
2005 Rhif 1649 (Cy.130)
BWYD, CYMRU
Rheoliadau Deunyddiau ac Eitemau Plastig mewn Cysylltiad â Bwyd (Diwygio) (Rhif 2) (Cymru) 2005
Wedi'u gwneud 21 Mehefin 2005
Yn dod i rym 24 Mehefin 2005
Mae Cynulliad Cenedlaethol Cymru, drwy arfer y pwerau a roddwyd gan adrannau 16(2), 17(1), 26(1)(a) a (3) a 48(1) o Ddeddf Diogelwch Bwyd 1990 ac sydd bellach wedi'u breinio ynddo ac wedi rhoi sylw yn unol ag adran 48(4A) o'r Ddeddf honno i gyngor perthnasol a roddwyd gan yr Asiantaeth Safonau Bwyd ac ar ôl ymgynghori fel sy'n ofynnol gan Erthygl 9 o Reoliad (EC) Rhif 178/2002 Senedd Ewrop a'r Cyngor, sy'n pennu egwyddorion cyffredinol a gofynion cyfraith bwyd, yn sefydlu Awdurdod Diogelwch Bwyd Ewrop ac yn pennu gweithdrefnau o ran materion diogelwch bwyd, yn gwneud y Rheoliadau a ganlyn:
Enwi, cymhwyso a chychwyn
1 
Enw'r Rheoliadau hyn yw Rheoliadau Deunyddiau ac Eitemau Plastig mewn Cysylltiad â Bwyd (Diwygio) (Rhif 2) (Cymru) 2005 sy'n gymwys o ran Cymru a deuant i rym ar 24 Mehefin 2005.
Diwygiadau i Reoliadau Deunyddiau ac Eitemau Plastig mewn Cysylltiad â Bwyd 1998
2 
Diwygir Rheoliadau Deunyddiau ac Eitemau Plastig mewn Cysylltiad â Bwyd 1998 i'r graddau y maent yn gymwys o ran Cymru yn unol â rheoliadau 3 i 16 o'r Rheoliadau hyn.
3 
Yn rheoliad 2 (dehongli) —
(a) ym mharagraff (1)—
(i) yn lle'r diffiniad o “additive” rhodder ““additive” means a substance as defined in paragraph 1 of the general introduction to Annex III to the Directive as read with paragraph 3 of article 4 of the Directive;”;
(ii) yn y diffiniad o “Council Directive 82/711”, hepgorer y geiriau “as amended” hyd at y diwedd;
(iii) ar ôl y diffiniad o “Council Directive 82/711” mewnosoder y diffiniadau canlynol—“
 “Council Directive 88/388” means Council Directive 88/388/EEC on the approximation of the laws of the Member States relating to flavourings for use in foodstuffs and to source materials for their production;
 “Council Directive 89/107” means Council Directive 89/107/EEC on the approximation of the laws of the Member States concerning food additives authorised in foodstuffs intended for human consumption;”;
(iv) hepgorer y diffiniad o “EEA Agreement”;
(v) yn lle'r diffiniad o “EEA State” rhodder ““EEA State” means a Member State (other than the United Kingdom), Norway, Iceland and Liechtenstein;”;
(vi) ar ôl y diffiniad o “EEA State” mewnosoder y diffiniad canlynol —“
 “EFSA” means the European Food Safety Authority;”;
(vii) ar ôl y diffiniad o “preparation” mewnosoder y diffiniad canlynol—“
 “the purity Directives” means Commission Directive 95/31/EC laying down specific criteria of purity concerning sweeteners for use in foodstuffs, Commission Directive 95/45/EC laying down purity criteria concerning colours for use in foodstuffs and Commission Directive 96/77/EC laying down specific purity criteria for food additives other than colours or sweeteners;”;
(b) ar ôl paragraff (5) ychwaneger—“
(6) Any reference in these Regulations to a Community instrument is to be construed as a reference to that instrument as amended at the time the Plastic Materials and Articles in Contact with Food (Amendment) (No. 2) (Wales) Regulations 2005 were made.”.
4 
Yn rheoliad 4 (cyfyngiad ar ddefnyddio monomerau wrth weithgynhyrchu deunyddiau ac eitemau plastig)—
(a) ym mharagraff (2) hepgorer is-baragraffau (a) a (b);
(b) ym mharagraff (5)(b)(ii) ar ôl y gair “material” ym mhob achos mewnosoder y geiriau “or article”.
5 
Yn rheoliad 5 (cyfyngiad ar ddefnyddio ychwanegion wrth weithgynhyrchu deunyddiau ac eitemau plastig)—
(a) ym mharagraff (1) ychwaneger ar ôl is-baragraff (d)—“
(e) any food additive authorised by Council Directive 89/107 or any flavouring authorised by Council Directive 88/388 that migrates into food —
(i) in a quantity that has a technological function in the final food product, or
(ii) where the food is of a type for which the use of any such food additive or flavouring is so authorised, in quantities exceeding the limits provided for in Council Directive 89/107 or Council Directive 88/388 as appropriate, or in Schedule 2 to these Regulations, whichever is the lower.”.
(b) ym mharagraff (4)(b)(ii) ar ôl y gair “material” ym mhob achos mewnosoder y geiriau “or article”.
6 
Ar ôl rheoliad 5A mewnosoder y rheoliad canlynol—“
Applications for inclusion of an additive in the Community list of authorised additives
5B. 

(1) This regulation applies where a person wishes to make an application for the inclusion of an eligible additive in the Community list referred to in article 4 of the Directive.
(2) An application mentioned in paragraph (1) including supporting data must be made to EFSA before 1st January 2007.
(3) If, during examination of the data referred to in paragraph (2), EFSA calls for supplementary information, the eligible additive may, if permitted to be used under the laws of England and Wales, continue to be so used until EFSA has issued an opinion, provided such information is submitted within the time limits specified by EFSA.
(4) For the purposes of this regulation an eligible additive is one whose use is permitted in one or more Member States before 1st January 2007.”.
7 
Yn lle rheoliad 8 (labelu) rhodder y canlynol —“
 At marketing stages other than the retail stage a person who is in possession of any plastic material or article intended to come into contact with food is to ensure that the plastic material or article is accompanied by a written declaration which —
(a) attests that it complies with the legislation applicable to it; and
(b) provides, in respect of substances that are subject to a restriction on quantities migrating into food, information obtained from experimental data or theoretical calculation concerning —
(i) the levels of migration specific to those substances;
(ii) where appropriate, purity criteria in accordance with the purity Directives.”.
8 
Yn rheoliad 10 (tramgwyddau) —
(a) ym mharagraff (1) yn lle'r ffigur “8(1)”, rhodder y ffigur “8”;
(b) ar ôl paragraff (24) ychwaneger —“
(25) In any proceedings for an offence under these Regulations it is a defence to prove that —
(a) the act constituting the offence was committed in relation to a plastic material or article which was manufactured or imported into the European Community before 1st March 2006; and
(b) the act constituting the offence would not have constituted an offence under these Regulations if the amendments made to them by the Plastic Materials and Articles in Contact with Food (Amendment) (No. 2) (Wales) Regulations 2005 had not been in force at the time that act occurred.”.
9 
Yn Atodlen 1, Rhan 1—
(a) yn Adran A (monomerau a awdurdodwyd heb derfyn amser) —
(i) mewnosoder yn y drefn rifo briodol y cofnodion a nodir yn Atodlen 1 i'r Rheoliadau hyn;
(ii) yn lle eitemau 15A, 39, 70, 120B, 147, 147A, 147B a 188 rhodder y cofnodion a nodir yn Atodlen 2 i'r Rheoliadau hyn;
(iii) hepgorer eitemau 76B a 76C a'u cofnodion cyfatebol;
(b) hepgorer Adrannau B a C.
10 
Yn Atodlen 1, Rhan II (atodol) paragraff 4—
(a) ar ddiwedd nodyn (21) yn lle “and 18670,” rhodder “,18670, 54880 a 59280”;
(b) ar ôl nodyn (25) ychwaneger y canlynol—“
(27) QMA(T) in this case means that the restriction is not to be exceeded by the sum of the residual quantities of the following substances having PM/REF Nos. 10599/90A, 10599/91, 10599/92A and 10599/93.
(28) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 13480 and 39680.
(29) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 22775 and 69920.
(32) Compliance testing when there is a fat contact should be performed using isoctane as substitute of simulant D (unstable).
(33) QMA(T) in this case means that the restriction is not to be exceeded by the sum of the residual quantities of the following substances having PM/REF Nos. 14800 and 45600.”
11 
Yn Atodlen 2, Rhan I (rhestr anghyflawn o ychwanegion a ddefnyddir wrth weithgynhyrchu deunyddiau ac eitemau plastig) —
(a) mewnosoder yn y drefn rifo briodol y cofnodion a nodir yn Atodlen 3 i'r Rheoliadau hyn;
(b) yn lle eitemau 60A a 198A rhodder y cofnodion a nodir yn Atodlen 4 i'r Rheoliadau hyn;
(c) hepgorer eitemau 112, 173A, 195C a 240 gyda'u cofnodion cyfatebol.
12 
Yn Atodlen 2, Rhan II (rhestr anghyflawn o ychwanegion a ddefnyddir wrth weithgynhyrchu deunyddiau ac eitemau plastig y mae paragraff 5 o Ran III o Atodlen 2 yn gymwys iddi) —
(a) mewnosoder yn y drefn rifo briodol y cofnodion a nodir yn Atodlen 5 i'r Rheoliadau hyn;
(b) hepgorer eitemau 28, 80 a 111A gyda'u cofnodion cyfatebol.
13 
Yn Atodlen 2, Rhan III (atodol) —
(a) ym mharagraff 4—
(i) yn nodyn (8), mewnosoder yn y drefn rifo briodol “38000” a “67896”;
(ii) yn nodyn (10), ar ôl “levels” mewnosoder “(expressed as iodine)”;
(iii) ar ddiwedd nodyn (21), yn lle “and 18670,” rhodder “, 18670, 54880 a 59280”;
(iv) ar ôl nodyn (24) ychwaneger y canlynol—“
(26) QMA(T) in this case means that the restriction is not to be exceeded by the sum of the residual quantities of the following substances mentioned as reference Nos. 14950, 15700, 16240, 16570, 16600, 16630, 18640, 19110, 22332, 22420, 22570, 25210, 25240 and 25270.
(27) QMA(T) in this case means that the restriction is not to be exceeded by the sum of the residual quantities of the following substances having PM/REF Nos. 10599/90A, 10599/91, 10599/92A and 10599/93.
(28) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 13480 and 39680.
(29) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 22775 and 69920.
(30) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 86480, 86960 and 87120.
(31) Compliance testing when there is a fat contact should be performed using saturated fatty food simulants as simulant D.
(32) Compliance testing when there is a fat contact should be performed using isoctane as substitute of stimulant D (unstable).
(33) QMA(T) in this case means that the restriction is not to be exceeded by the sum of the residual quantities of the following substances having PM/REF Nos. 14800 and 45600.
(34) SML(T) in this case means that the restriction is not to be exceeded by the sum of the migration levels of the following substances having PM/REF Nos. 55200, 55280 and 55360.”;
(b) ym mharagraff 5 yn lle “1st January 2004” rhodder “1st July 2006”.
14 
Yn Atodlen 2A (cynhyrchion a gafwyd drwy eplesu bacterol) yn lle'r cofnod yn y golofn sy'n dwyn y pennawd “restrictions and specifications” rhodder y canlynol —“
 In compliance with specifications included in Schedule 2B”.
15 
Yn lle Atodlen 2B (manylebau) rhodder y tabl a nodir yn Atodlen 6 i'r Rheoliadau hyn.
16 
Yn lle paragraff 4(b) o Ran I (rheolau sylfaenol) o Atodlen 4 (profion ymfudo cyffredinol a phenodol gan ddefnyddio efelychwyr bwyd) rhodder —“
(b) omit the migration, the substitute or the alternative tests where —
(i) there is conclusive proof that the migration limits cannot be exceeded in any foreseeable conditions of use of the material or article, or
(ii) the conditions for non-compulsory testing set out in article 8.2 and 8.3 of the Directive are met.”.
Llofnodwyd ar ran Cynulliad Cenedlaethol Cymru o dan adran 66(1) o Ddeddf Llywodraeth Cymru 1998
D. Elis-Thomas
Llywydd y Cynulliad Cenedlaethol
21 Mehefin 2005
ATODLEN 1
(COFNODION I'W MEWNOSOD YN ADRAN A O RAN I O ATODLEN 1)
Rheoliad 9(a)(i)


 1 2 3 4
Item PM/REF No. CAS No. Name Restrictions and specifications
6A 10599/90A 061788-89-4 Acids, fatty, unsaturated (C18), dimers, distilled QMA(T) = 0.05 mg/6 dm2 (27)
6B 10599/91 061788-89-4 Acids, fatty, unsaturated (C18), dimers, non distilled QMA(T) = 0.05 mg/6 dm2 (27)
6C 10599/92A 068783-41-5 Acids, fatty, unsaturated (C18), dimers, hydrogenated, distilled QMA(T) = 0.05 mg/6 dm2 (27)
6D 10599/93 068783-41-5 Acids, fatty, unsaturated (C18), dimers, hydrogenated, non distilled QMA(T) = 0.05 mg/6 dm2 (27)
37A 13323 000102-40-9 1,3-Bis(2-hydroxyethoxy) benzene SML = 0.05 mg/kg
68MA 14800 003724-65-0 Crotonic acid QMA(T) = 0.05 mg/6 dm2 (33)
87A 16210 006864-37-5 3,3'-Dimethyl-4,4'- diaminodicyclohexylmethane SML = 0.05 mg/kg (32). To be used only in polyamides.
89A 16540 000102-09-0 Diphenyl carbonate SML = 0.05 mg/kg
101A 17110 016219-75-3 5-Ethylidenebicyclo [2,2,1]hept-2-ene QMA = 0.05 mg/6 dm2. The ratio surface / quantity of food shall be lower than 2 dm2/kg
118MA 18700 000629-11-8 1,6-Hexanediol SML = 0.05 mg/kg
120ZA 18896 001679-51-2 4-(Hydroxymethyl)-1-cyclohexene SML = 0.05 mg/kg
135BM 20440 000097-90-5 Methacrylic acid, diester with ethyleneglycol SML = 0.05 mg/kg
142A 21400 054276-35-6 Methacrylic acid, sulphopropyl ester QMA = 0.05 mg/6 dm2
156XA 22775 000144-62-7 Oxalic acid SML(T) = 6 mg/kg(29)
161A 23070 000102-39-6 (1,3-Phenylenedioxy) diacetic acid QMA = 0.05 mg/6 dm2
ATODLEN 2
(COFNODION I'W RHOI YN LLE COFNODION YN ADRAN A O RAN I O ATOCLEN 1)
Rheoliad 9(a)(ii)


 1 2 3 4
Item PM/REF No. CAS No. Name Restrictions and specifications
15A 11530 00999-61-1 Acrylic acid, 2-hydroxypropyl ester QMA = mg/6 dm2 for the sum of acrylic acid, 2-hydroxypropyl ester and acrylic acid, 2-hydroxyisopropyl ester and in compliance with the specifications laid down in Schedule 2B
39 13480 000080-05-7 2,2-Bis (4-hydroxyphenyl) propane SML(T) = 0.6 mg/kg (28)
70 14950 003173-53-3 Cyclohexyl isocyanate QMT(T) = 1 mg/kg in FP (expressed as NCO) (26)
120B 18898 000103-90-2 N-(4-Hydroxyphenyl) acetamide SML = 0.05 mg/kg
147 22150 000691-37-2 4-Methyl-1-pentene SML = 0.05 mg/kg
147A 22331 025513-64-8 Mixture of (35-45% w/w) 1,6-diamino-2,2, 4-trimethylhexane and (55—65% w/w) 1,6-diamino-2,4,4-trimethylhexane QMA = 5 mg/6 dm2
147B 22332 — Mixture of (40% w/w) 2,2, 4-trimethylhexane-1,6-diisocyanate and (60% w/w) 2,4,4-trimethylhexane-1,6-diisocyanate QM(T) — 1 mg/kg (expressed as NCO) (26)
188 24190 065997-05-9 Rosin Wood 
ATODLEN 3
(COFNODION I'W MEWNOSOD YN RAN I O ATODLEN 22)
Rheoliad 11(a)


 1 2 3 4
Item PM/REF No. CAS No. Name Restrictions and specifications
18A 34850 143925-92-2 Amines, bis(hydrogenated tallow alkyl) oxidised QM = For use only:
(a) in polyolefines at 0.1% (w/w) but not in LDPE when it is in contact with foods for which the Directive 85/572/EEC establishes a reduction factor less than 3;
(b) in PET at 0.25% (w/w) in contact with foods other of those for which the simulant D is laid down in Directive 85/572/EEC
18B 34895 000088-68-6 2-Aminobenzamide SML = 0.05 mg/kg. To be used only for PET for water and beverages
37AA 39680 000080-05-7 2,2-Bis(4-hydroxyphenyl) propane SML(T) = 0.6 mg/kg (28)
51A 42880 008001-79-4 Castor oil 
61A 45600 003724-65-0 Crotonic acid QMA(T) = 0.05 mg/6 dm2 (33)
61B 45640 005232-99-5 2-Cyano-3,3-diphenylacrylic acid, ethyl ester SML = 0.05 mg/kg
69A 46700 — 15,7-di-tert-Butyl-3-(3,4-and 2,3-di-methylphenyl)-3H-benzofuran-2-one containing: 3(a)5,7-di-tert-butyl-3-(3,4-dimethylphenyl)-3H-benzofuran-2-one (80-100% w/w); and 3(b)5,7-di-tert-butyl-3-(2,3-dimethylphenyl)-3H-benzofuran-2-one (0-20% w/w) SML = 5 mg/kg
69B 46720 004130-42-1 2,6-Di-tert-butyl-4-ethylphenol QMA = 4.8 mg/6 dm2
109A 56535 — Glycerol, esters with nonanoic acid 
131A 59280 000100-97-0 Hexamethylenetetramine SML(T) = 15 mg/kg (21) (expressed as Formaldehyde)
178A 68078 027253-31-2 Neodecanoic acid, cobalt salt SML(T) = 0.05 mg/kg (expressed as Neodecanoic acid) and SML(T) = 0.05 mg/kg (13) (expressed as Cobalt). Not for use in polymers contacting foods for which simulant D is laid down in Directive 85/572/EEC
182A 69920 000144-62-7 Oxalic acid SML(T) = 6 mg/kg (29)
195D 76866 — Polyesters of 1,2-propanediol and/or 1,3- and/or 1,4-butanediol and/or polypropyleneglycol with adipic acid, which may be end-capped with acetic acid or fatty acids C12-C18 or n-octanol and / or n-decanol SML = 30 mg/kg
240ZA 85601 — Silicates, natural (with the exception of asbestos) 
280B 95000 028931-67-1 Trimethylolpropane trimethacrylatemethyl methacrylate copolymer 
ATODLEN 4
(COFNODION I'W RHOI YN LLE COFNODION YN RAN I O ATODLEN 2)
Rheoliad 11(b)


 1 2 3 4
Item PM/REF No. CAS No. Name Restrictions and specifications
60A 45450 068610-51-5 p-Cresol-dicyclopentadiene-isobutylene, copolymer SML = 5 mg/kg
198A 77895 068439-49-6 Polyethyleneglycol (EO = 2-6) monoalkyl (C16—C18) ether SML = 0.05 mg/kg and in compliance with the specifications laid down in Schedule 2B
ATODLEN 5
(COFNODION I'W MEWNOSOD YN RAN II O ATODLEN 2)
Rheoliad 12(a)


 1 2 3 4
Item PM/REF No. CAS No. Name Restrictions and specifications
4A 34650 151841-65-5 Aluminium hydroxybis [2,2'-methylenebis (4,6-di-tert-butylphenyl) phosphate] SML = 5 mg/kg
7A 38000 000553-54-8 Benzoic acid, lithium salt SML(T) = 0.6 mg/kg (8) (expressed as Lithium)
18A 40720 025013-16-5 tert-Butyl-4-hydroxyanisole (= BHA) SML = 30 mg/kg
27B 46640 000128-37-0 2,6-Di-tert-butyl-p-cresol (= BHT) SML = 3.0 mg/kg
54A 54880 000050-00-0 Formaldehyde SML(T) = 15 mg/kg (21)
54B 55200 001166-52-5 Gallic acid, dodecyl ester SML(T) = 30 mg/kg (34)
54C 55280 001034-01-1 Gallic acid, octyl ester SML(T) = 30 mg/kg (34)
54D 55360 000121-79-9 Gallic acid, propyl ester SML(T) = 30 mg/kg (34)
79A 67896 020336-96-3 Myristic acid, lithium salt SML(T) = 0.6 mg/kg (8) (expressed as Lithium)
83A 71935 007601-89-0 Perchloric acid, sodium salt monohydrate SML = 0.05 mg/kg (31)
88A 76680 068132-00-3 Polycyclopentadiene, hydrogenated SML = 5 mg/kg (1)
101A 86480 007631-90-5 Sodium bisulphite SML(T) = 10 mg/kg (30) (expressed as S02)
102A 86920 007632-00-0 Sodium nitrite SML = 0.6 mg/kg
102B 86960 007757-83-7 Sodium sulphite SML(T) = 10 mg/kg (30) (expressed as S02)
102C 87120 007772-98-7 Sodium thiosulphate SML(T) = 10 mg/kg (30) (expressed as S02)
110A 94400 036443-68-2 Triethyleneglycol bis[3-(3-tert-butyl-4-hydroxy-5-methylphenyl) propionate] SML = 9 mg/kg
ATODLEN 6
(TABL I'W ROI YN LLE TABL YN ATODLEN 2B)
Rheoliad 15


Item PM/REF No. Specifications
1 11530 Acrylic acid, 2-hydroxypropyl ester.It may contain up to 25% (m/m) of acrylic acid, 2-hydroxyisopropyl ester (CAS No. 002918-23-2)
2 16690 DivinylbenzeneIt may contain up to 45% (m/m) of Ethylvinylbenzene
3 18888 3-Hydroxybutanoic acid-3-hydroxypentanoic acid, copolymer
  Definition The copolymers are produced by the controlled fermentation of Alcaligenes eutrophus using mixtures of glucose and propanoic acid as carbon sources. The organism used has not been genetically engineered and has been derived from a single wild-type organism Alcaligenes eutrophus strain H16 NCIMB 10422. Master stocks of the organism are stored as freeze-dried ampoules. A submaster / working stock is prepared from the master stock and stored in liquid nitrogen and used to prepare inocula for the fermenter. Fermenter samples will be examined daily both microscopically and for any changes in colonial morphology on a variety of agars at different temperatures. The copolymers are isolated from heat treatment bacteria by controlled digestion of the other cellular components, washing and drying. These copolymers are normally offered as formulated, melt formed granules containing additives such as nucleating agents, plasticisers, fillers, stabilisers and pigments which all conform to the general and individual specifications.
  Chemical name Poly(3-D-hydroxybutanoate-co-3-D-hydroxypentanoate)
  CAS number 080181-31-3
  Structural formula   CH3 
   CH3 O CH2 O
   | || | ||
   (-O-CH-CH2-C-)m-(O-CH-CH2-C-)n
   where n / (m + n) greater than 0 and less or equal to 0.25
  Average molecular weight Not less than 150 000 Daltons (measured by gel permeation chromatography)
  Assay Not less than 98% poly(3-D-hydroxybutanoate-co-3-D-hydroxypentanoate) analysed after hydrolysis as a mixture of 3-D-hydroxybutanoic and 3-D-hydroxypentanoic acids
  Description White to off-white powder after isolation
  Characteristics
  Identification tests:
  Solubility Soluble in chlorinated hydrocarbons such as a chloroform or dichloromethane but practically insoluble in ethanol, aliphatic alkanes and water
  Restriction QMA for crotonic acid is 0.05 mg/6 dm2
  Purity Prior to granulation the raw material copolymer powder must contain:
  — nitrogen Not more than 2 500 mg/kg of plastic
  — zinc Not more than 100 mg/kg of plastic
  — copper Not more than 5 mg/kg of plastic
  — lead Not more than 2 mg/kg of plastic
  — arsenic Not more than 1 mg/kg of plastic
  — chromium Not more than 1 mg/kg of plastic
4 23547 Polydimethylsiloxane (MW > 6800)Minimum viscosity 100 centistokes at 25°C
5 25385 Triallylamine40 mg/kg hydrogel at a ratio of 1 kg food to a maximum of 1.5 grams of hydrogel.For use only in hydrogels intended for non-direct food contact use.
6 38320 4-(2-Benzoxazolyl)-4'-(5-methyl-2-benzoxazolyl) stilbeneNot more than 0.05% w/w (quantity of substance used / quantity of the formulation)
7 43680 Chlorodifluoromethane Content of chlorofluoromethane less than 1 substance
8 47210 Dibutylthiostannoic acid polymerMolecular unit = (C8H18S3Sn2)n (n = 1,5-2)
9 76721 Polydimethylsiloxane (Mw > 6800)Minimum viscosity 100 × 10-6 m2/s (= 100 centistokes) at 25°C
10 77895 Polyethyleneglycol (EO = 2—6) monoalkyl (C16—C18) etherThe composition of this mixture is as follows:
— polyethyleneglycol (EO = 2—6) monoalkyl (C16—C18) ether (approximately 28%)
— fatty alcohols (C16—C18) (approximately 48%)
— ethyleneglycol monoalkyl (C16—C18) ether (approximately 24%)
11 83595 Reaction product of di-tert-butylphosphonite with biphenyl, obtained by condensation of 2,4-di-tert-butylphenol with friedel craft reaction product of phosphorus trichloride and biphenyl
  Composition
— 4,4'-Biphenylene-bis [0,0-bis (2,4-di-tert-butylphenyl) phosphonite] (CAS No. 38613-77-3) (36-46% w/w (1))
— 4,3'-Biphenylene-bis [0,0-bis (2,4-di-tert-butylphenyl) phosphonite] (CAS No. 118421-00-4) (17-23% w/w)
— 3,3'-Biphenylene-bis [0,0-bis (2,4-di-tert-butylphenyl) phosphonite] (CAS No. 118421-01-5) (1-5% w/w)
— 4-Biphenylene-0,0-bis [0,0-bis (2,4-di-tert-butylphenyl) phosphonite] (CAS No. 91362-37-7) (11-19% w/w)
— Tris (2,4-di-tert-butylphenyl) phosphite (CAS No. 31570-04-4) (9-18% w/w)
— 4,4'-Biphenylene-0,0-bis [0,0-bis (2,4-di-tert-butylphenyl) phosphonate-0,0-bis (2,4-di-tert-butylphenyl) phosphonite] (CAS No. 112949-970) (5% w/w )Other specifications
— Phosphor content of minimum 5.4% to 5.9%
— Acid value of maximum 10 mg KOH per gram
— Melt range of 85—110°C
12 88640 Soyabean oil, epoxidizedOxirane < 8%, iodine number < 6
13 95859 Waxes, refined, derived from petroleum based or synthetic hydrocarbon feedstocksThe product has the following specifications:
— Content of mineral hydrocarbons with carbon number less than 25: not more than 5% (w/w)
— Viscosity not less than 11 × 10−6 m2/s (= 11 centistokes) at 100°C
— Average molecular weight not less than 500
14 95883 White mineral oils, paraffinic, derived from petroleum hydrocarbon feedstocksThe product has the following specifications:
— Content of mineral hydrocarbons with carbon number less than 25: not more than 5% (w/w)
— Viscosity note less than 8.5 × 10−6 m2/s (= 8.5 centistokes) at 100°C
— Average molecular weight not less than 480