
COUNCIL DIRECTIVE of 26 July 1971 on the approximation of the laws of the Member States relating to 5 to 50 kilogramme medium accuracy rectangular bar weights and 1 to 10 kilogramme medium accuracy cylindrical weights (71/317/EEC) (repealed) 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Article 1 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 2 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 3 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 4 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 5 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNEX I
RECTANGULAR BAR WEIGHTS
1. Shape, constituent material and method of manufacture 
 1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 1.2. Material used: 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. Adjustment cavity 
Type 1 
 2.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Type 2 
 2.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. Adjustment 
 3.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. Positioning of the EEC initial verification mark 
 4.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. Markings and distinctive symbols 
 5.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 5.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. Dimensions and tolerances 
 6.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 6.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. Maximum permissible errors 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. Surface finish 
 8.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ANNEX II
RECTANGULAR BAR WEIGHTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ANNEX III
CYLINDRICAL WEIGHTS
1. Shape, constituent material and method of manufacture 
 1.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 1.2. Material used: any material with a density of 7 to 9·5 g/cm3, of a hardness at least equal to that of cast brass, not less resistant to corrosion and not more friable than grey cast iron, and with a surface comparable to that of grey cast iron carefully cast in a mould of fine sand. 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 1.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. Adjusting cavity 
 2.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 2.5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. Adjustment 
 3.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. Positioning of the EEC initial verification mark 
 4.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 4.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. Markings and distinctive symbols 
 5.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 5.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 5.3. The nominal value of the weight is indicated in the form: 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. Dimensions and their tolerances 
 6.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
 6.2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. Maximum permissible errors 

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. Surface finish 
 8.1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ANNEX IV
CYLINDRICAL WEIGHTS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
