
Article 1 
Regulation (EU) No 1013/2006 is amended as follows:

((1)) Annexes IC, III, IIIA, IV, V and VII are amended in accordance with Annex I to this Regulation;
((2)) Annex VIII is replaced by the text in Annex II to this Regulation.
Article 2 
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
Article 1(1) shall apply from 1 January 2021.
This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Brussels, 19 October 2020.
For the Commission
The President
Ursula VON DER LEYEN
ANNEX I

Annexes IC, III, IIIA, IV, V and VII to Regulation (EC) No 1013/2006 are amended as follows:

((1)) in Annex IC, the second paragraph of point 25(e) is replaced by the following:
'Such codes may be included in Annexes IIIA, IIIB, IV (EU48) or IVA of this Regulation. In that case, the Annex number should be stated in front of the codes. As regards Annex IIIA, the relevant code(s) as indicated in Annex IIIA should be used, as appropriate in sequence. Certain Basel entries such as B1100 and B3020 are restricted to particular waste streams only, as indicated in Annex IIIA.';
((2)) Annex III is amended as follows:

((a)) the title is replaced by the following:
'LIST OF WASTES SUBJECT TO THE GENERAL INFORMATION REQUIREMENTS LAID DOWN IN ARTICLE 18 (“GREEN” LISTED WASTE)';
((b)) in part I, point (a) is replaced by the following:
'
((a)) Any reference in Annex IX of the Basel Convention to list A shall be understood as a reference to Annex IV to this Regulation;';
((c)) in part I, point (g) is replaced by the following:
'
((g)) For waste shipped within the Union, Basel entry B3011 does not apply and the following entry applies instead:

EU3011 Plastic waste (note the related entry AC300 in part II of Annex IV, and the related entry EU48 in part I of Annex IV):
Plastic waste listed below, provided it is almost free from contamination and other types of waste:

— Plastic waste almost exclusively consisting of one non-halogenated polymer, including but not limited to the following polymers:
— Polyethylene (PE)
— Polypropylene (PP)
— Polystyrene (PS)
— Acrylonitrile butadiene styrene (ABS)
— Polyethylene terephthalate (PET)
— Polycarbonates (PC)
— Polyethers
— Plastic waste almost exclusively consisting of one cured resin or condensation product, including but not limited to the following resins:
— Urea formaldehyde resins
— Phenol formaldehyde resins
— Melamine formaldehyde resins
— Epoxy resins
— Alkyd resins
— Plastic waste almost exclusively consisting of one of the following fluorinated polymers:
— Perfluoroethylene/propylene (FEP)
— Perfluoroalkoxy alkanes:
— Tetrafluoroethylene/perfluoroalkyl vinyl ether (PFA)
— Tetrafluoroethylene/perfluoromethyl vinyl ether (MFA)
— Polyvinylfluoride (PVF)
— Polyvinylidenefluoride (PVDF)
— Polytetrafluoroethylene (PTFE)
— Polyvinyl chloride (PVC).';
((d)) in part II, the following text is deleted:
'
GH013 391530 ex 390410—40 Polymers of vinyl chloride';
((3)) Annex IIIA is amended as follows:

((a)) in point 3, points (d), (e) and (f) are deleted;
((b)) the following point 4 is added:
'
4.. The following mixtures of wastes classified under separate indents or sub-indents of one single entry are included in this Annex only for the purposes of shipments within the Union:

((a)) mixtures of wastes classified under entry EU3011 and listed under the indent referring to non-halogenated polymers;
((b)) mixtures of wastes classified under entry EU3011 and listed under the indent referring to cured resins or condensation products;
((c)) mixtures of wastes classified under entry EU3011 and listed under “perfluoroalkoxy alkanes”.';
((4)) Annex IV is amended as follows:

((a)) the title is replaced by the following:
'LIST OF WASTES SUBJECT TO THE PROCEDURE OF PRIOR WRITTEN NOTIFICATION AND CONSENT (“AMBER” LISTED WASTE)';
((b)) Part I is amended as follows:

((i)) the first and second paragraphs are replaced by the following:
'The following wastes will be subject to the procedure of prior written notification and consent:Wastes listed in Annexes II and VIII to the Basel Convention.';
((ii)) point (a) is replaced by the following:
'
((a)) Any reference in Annex VIII of the Basel Convention to list B shall be understood as a reference to Annex III to this Regulation'.
((iii)) the following points (e) and (f) are added:
'
((e)) Basel entry A3210 does not apply and entry AC300 in part II applies instead.
((f)) For waste shipped within the Union, Basel entry Y48 does not apply and the following entry applies instead:

EU48: Plastic waste not covered by entry AC300 in part II or by entry EU3011 in part I of Annex III, as well as mixtures of plastic waste not covered by point 4 of Annex IIIA.';
((c)) In Part II, the following entry is inserted after the entry AC270:
'
AC300 Plastic waste, including mixtures of such wastes, containing or contaminated with Annex I constituents, to an extent that it exhibits an Annex III characteristic (note the related entry EU3011 in part I of Annex III, and the related entry EU48 in part I)';
((5)) Annex V is amended as follows:

((a)) Part 1 is amended as follows:

((i)) in List A, section A3, the following entry is added:
'
A3210 Plastic waste, including mixtures of such waste, containing or contaminated with Annex I constituents, to an extent that it exhibits an Annex III characteristic (note the related entry B3011, in list B of this Part, and entry Y48, in list A of Part 3)';
((ii)) in List B, section B3 is amended as follows:

— entry B3010 is deleted;
— the following entry is inserted before entry B3020:
'
B3011 Plastic waste (note the related entry A3210, in list A of this Part, and entry Y48, in list A of Part 3)

— Plastic waste listed below, provided it is destined for recycling in an environmentally sound manner and almost free from contamination and other types of wastes:
— Plastic waste almost exclusively consisting of one non-halogenated polymer, including but not limited to the following polymers:
— Polyethylene (PE)
— Polypropylene (PP)
— Polystyrene (PS)
— Acrylonitrile butadiene styrene (ABS)
— Polyethylene terephthalate (PET)
— Polycarbonates (PC)
— Polyethers
— Plastic waste almost exclusively consisting of one cured resin or condensation product, including but not limited to the following resins:
— Urea formaldehyde resins
— Phenol formaldehyde resins
— Melamine formaldehyde resins
— Epoxy resins
— Alkyd resins
— Plastic waste almost exclusively consisting of one of the following fluorinated polymers:
— Perfluoroethylene/propylene (FEP)
— Perfluoroalkoxy alkanes:
— Tetrafluoroethylene/perfluoroalkyl vinyl ether (PFA)
— Tetrafluoroethylene/perfluoromethyl vinyl ether (MFA)
— Polyvinylfluoride (PVF)
— Polyvinylidenefluoride (PVDF)
— Mixtures of plastic waste, consisting of polyethylene (PE), polypropylene (PP) and/or polyethylene terephthalate (PET), provided they are destined for separate recycling of each material and in an environmentally sound manner, and almost free from contamination and other types of wastes.';
((b)) in Part 3, List A is replaced by the following:
'

Y46 Waste collected from households
Y47 Residues arising from the incineration of household wastes
Y48 Plastic waste, including mixtures of such waste, with the exception of the following:

— Plastic waste that is hazardous waste (see entry A3210 in part 1 of list A in Annex V)
— Plastic waste listed below, provided it is destined for recycling in an environmentally sound manner and almost free from contamination and other types of wastes:
— Plastic waste almost exclusively consisting of one non-halogenated polymer, including but not limited to the following polymers:
— Polyethylene (PE)
— Polypropylene (PP)
— Polystyrene (PS)
— Acrylonitrile butadiene styrene (ABS)
— Polyethylene terephthalate (PET)
— Polycarbonates (PC)
— Polyethers
— Plastic waste almost exclusively consisting of one cured resin or condensation product, including but not limited to the following resins:
— Urea formaldehyde resins
— Phenol formaldehyde resins
— Melamine formaldehyde resins
— Epoxy resins
— Alkyd resins
— Plastic waste almost exclusively consisting of one of the following fluorinated polymers:
— Perfluoroethylene/propylene (FEP)
— Perfluoroalkoxy alkanes:
— Tetrafluoroethylene/perfluoroalkyl vinyl ether (PFA)
— Tetrafluoroethylene/perfluoromethyl vinyl ether (MFA)
— Polyvinylfluoride (PVF)
— Polyvinylidenefluoride (PVDF)
— Mixtures of plastic waste, consisting of polyethylene (PE), polypropylene (PP) and/or polyethylene terephthalate (PET), provided they are destined for separate recycling of each material and in an environmentally sound manner and almost free from contamination and other types of wastes.
';
((c)) in Part 3, the heading of List B is replaced by the following:
'List B (Waste from Appendix 4, Part II of the OECD Decision)';
((6)) Annex VII is amended as follows:
In block 10, the following is added:
'
((vii)) Other (please specify):'.

ANNEX II

'
ANNEX VIII  I.  1. Technical guidelines on the environmentally sound management of biomedical and health care wastes (Y1; Y3)
 2. Technical guidelines on the environmentally sound management of waste lead acid batteries1
 3. Technical guidelines on the environmentally sound management of the full and partial dismantling of ships1
 4. Technical guidelines on the environmentally sound recycling/reclamation of metals and metal compounds (R4)
 5. General technical guidelines for the environmentally sound management of wastes consisting of, containing or contaminated with persistent organic pollutants
 6. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with 1,1,1 trichloro 2,2 bis (4 chlorophenyl) ethane (DDT)
 7. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with hexabromocyclododecane (HBCD)
 8. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with perfluorooctane sulfonic acid (PFOS), its salts and perfluorooctane sulfonyl fluoride (PFOSF)5
 9. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with pentachlorophenol and its salts and esters (PCP)
 10. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with the pesticides aldrin, alpha hexachlorocyclohexane, beta hexachlorocyclohexane, chlordane, chlordecone, dieldrin, endrin, heptachlor, hexachlorobenzene, hexachlorobutadiene, lindane, mirex, pentachlorobenzene, pentachlorophenol and its salts, perfluorooctane sulfonic acid, technical endosulfan and its related isomers or toxaphene or with hexachlorobenzene as an industrial chemical (POP Pesticides)6
 11. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with polychlorinated biphenyls, polychlorinated terphenyls, polychlorinated naphthalenes or polybrominated biphenyls including hexabromobiphenyl (PCBs, PCTs, PCNs or PBBs, including HBB)6
 12. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with hexabromodiphenyl ether and heptabromodiphenyl ether, or tetrabromodiphenyl ether and pentabromodiphenyl ether or decabromodiphenyl ether (POP-BDEs)3
 13. Technical Guidelines for the Environmentally Sound Management of Wastes Containing or Contaminated with unintentionally produced polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, hexachlorobenzene, polychlorinated biphenyls, pentachlorobenzene, polychlorinated naphthalenes or hexachlorobutadiene3
 14. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with hexachlorobutadiene3
 15. Technical guidelines on the environmentally sound management of wastes consisting of, containing or contaminated with short-chain chlorinated paraffins3
 16. Technical guidelines for the environmentally sound management of used and waste pneumatic tyres
 17. Technical guidelines for the environmentally sound management of wastes consisting of, containing or contaminated with mercury or mercury compounds5
 18. Technical guidelines for the environmentally sound co-processing of hazardous wastes in cement kilns7
 19. Guidance document on the environmentally sound management of used and end-of-life computing equipment6
 20. Guidance document on environmentally sound management of used and end-of-life mobile phones7
 21. Framework for the environmentally sound management of hazardous wastes and other wastes
 22. Practical manuals for the promotion of the environmentally sound management of wastes
 II. 
Technical guidance for the environmentally sound management of specific waste streams:

Used and scrap personal computers
 III. 
Guidelines on ship recycling
 IV. 
Safety and health in shipbreaking guidelines for Asian countries and Turkey
'
