
Article 1 

1. This Regulation lays down the provisions necessary for the ... application of the following aspects regarding tachographs:
(a) recording of the position of the vehicle at certain points during the daily working period of the driver;
(b) remote early detection of possible manipulation or misuse of smart tachographs;
(c) interface with intelligent transport systems;
(d) the administrative and technical requirements for the type-approval procedures of tachographs, including the security mechanisms.
2. The construction, testing, installation, inspection, operation and repair of smart tachographs and their components, shall comply with the technical requirements set out in Annex IC to this Regulation.
3. Tachographs other than smart tachographs shall continue, as regards construction, testing, installation, inspection, operation and repair, to comply with the requirements of either Annex I to Regulation (EU) No 165/2014 or Annex IB to  Regulation (EU) No 165/2014, as applicable.
4. ... The remote early detection facility shall also transmit the weight data provided by  any internal on-board weighing system installed to aid the enforcement of requirements as to the maximum authorised weight of vehicles, for the purpose of early fraud detection.
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 2 
For the purposes of this Regulation, the definitions laid down in Article 2 of Regulation (EU) No 165/2014 shall apply.
In addition, the following definitions shall apply:

((1)) ‘digital tachograph’ or ‘first generation tachograph’ means a digital tachograph other than a smart tachograph;
((2)) ‘external GNSS facility’ means a facility which contains the GNSS receiver when the vehicle unit is not a single unit, as well as other components needed to protect the communication of data about position to the rest of the vehicle unit;
((3)) ‘information folder’ means the complete folder, in electronic or paper form, containing all the information supplied by the manufacturer or its agent to the  Secretary of State  for the purpose of the type-approval of a tachograph or a component thereof, including the certificates referred to in Article 12(3) of Regulation (EU) No 165/2014, the performance of the tests defined in Annex IC to this Regulation, as well as drawings, photographs, and other relevant documents;
((4)) ‘information package’ means the information folder, in electronic or paper form, accompanied by any other documents added by the  Secretary of State  to the information folder in the course of carrying out their functions including, at the end of the type-approval process, the ... type-approval certificate of the tachograph or a component thereof;
((5)) ‘index to the information package’ means the document listing the numbered contents of the information package identifying all the relevant parts of this package. The format of that document shall distinguish the successive steps in the ... type-approval process, including the dates of any revisions and updating of that package;
((6)) ‘remote early detection facility’ means the equipment of the vehicle unit which is used to perform targeted roadside checks;
((7)) ‘smart tachograph’ or ‘second generation tachograph’ means a digital tachograph complying with Articles 8, 9 and 10 of Regulation (EU) No 165/2014 as well as with Annex IC to this Regulation;
((8)) ‘tachograph component’ means any of the following elements: the vehicle unit, the motion sensor, the record sheet, the external GNSS facility and the external remote early detection facility;
((9)) ...
((10)) ‘vehicle unit’ means the tachograph excluding the motion sensor and the cables connecting the motion sensor.
It may be a single unit or several units distributed in the vehicle and includes a processing unit, a data memory, a time measurement function, two smart card interface devices for driver and co-driver, a printer, a display, connectors and facilities for entering the user’s inputs, a GNSS receiver and a remote communication facility.
The vehicle unit may be composed of the following components subject to type-approval:

— vehicle unit, as a single component (including GNSS receiver and remote communication facility),
— vehicle unit main body (including remote communication facility), and external GNSS facility,
— vehicle unit main body (including GNSS receiver), and external remote communication facility,
— vehicle unit main body, external GNSS facility, and external remote communication facility.
If the vehicle unit is composed of several units distributed in the vehicle, the vehicle unit main body is the unit containing the processing unit, the data memory, and the time measurement function.
‘vehicle unit (VU)’ is used for ‘vehicle unit’ or ‘vehicle unit main body’.
Article 3 

1. Manufacturers shall ensure that smart tachographs are compatible with the positioning services provided by the Galileo and the European Geostationary Navigation Overlay Service (‘EGNOS’) systems.
2. In addition to the systems referred to in paragraph 1, manufacturers may also choose to ensure compatibility with other satellite navigation systems.
Article 4 

1. A manufacturer or its agent shall submit an application for type-approval of a tachograph or any of its components, or group of components, to  the Secretary of State. It shall consist of an information folder containing the information for each of the components concerned including, where applicable, the type-approval certificates of other components necessary to complete the tachograph, as well as any other relevant documents.
2. The Secretary of State  shall grant type-approval to any tachograph, component or group of components that conforms to the administrative and technical requirements referred to in Article 1(2) or (3), as applicable. In that case, the  Secretary of State  shall issue to the applicant a type-approval certificate that shall conform to the model laid down in Annex II to this Regulation.
3. The  Secretary of State  may request the manufacturer or its agent to supply any additional information.
4. The manufacturer or its agent shall make available to the Secretary of State, as well as to the  persons  responsible for issuing the certificates referred to in Article 12(3) of Regulation (EU) No 165/2014, as many tachographs or tachograph components as are necessary to enable the type-approval procedure to be conducted satisfactorily.
5. Where the manufacturer or its agent seeks a type-approval of certain components or groups of components of a tachograph, he shall provide the  Secretary of State  with the other components, already type-approved, as well as other parts necessary for the construction of the complete tachograph, in order for  the Secretary of State  to conduct the necessary tests.
Article 5 

1. The manufacturer or its agent shall inform  the Secretary of State without delay, about any modification in software or hardware of the tachograph or in the nature of the materials used for its manufacture which are recorded in the information package and shall submit an application for the modification of the type-approval.
2. The  Secretary of State  may revise or extend an existing type-approval, or issue a new type-approval according to the nature and characteristics of the modifications.A ‘revision’ shall be made where the  Secretary of State  considers that the modifications in software or hardware of the tachograph or in the nature of materials used for its manufacture are minor. In such cases, the Secretary of State shall issue the revised documents of the information package, indicating the nature of the modifications made and the date of their approval. An updated version of the information package in a consolidated form, accompanied by a detailed description of the modifications made, shall be sufficient to meet this requirement.An ‘extension’ shall be made where the Secretary of State considers that the modifications in software or hardware of the tachograph or in the nature of materials used for its manufacture are substantial. In such cases, it may request that new tests be conducted and inform the manufacturer or its agent accordingly. If those tests prove satisfactory, the Secretary of State shall issue a revised type-approval certificate containing a number referring to the extension granted. The type-approval certificate shall mention the reason of the extension and its date of issue.
3. The index to the information package shall indicate the date of the most recent extension or revision of the type-approval, or the date of the most recent consolidation of the updated version of the type-approval.
4. A new type-approval shall be necessary when the requested modifications to the type-approved tachograph or its components would lead to the issuance of a new security or interoperability certificate.
Article 6 
This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
It shall apply from 2 March 2016.
However, Annex IC shall apply from 15 June 2019 with the exception of Appendix 16 which shall apply from 2 March 2016.
...
ANNEX I C
The first generation digital tachograph system has been deployed since 1 May 2006. It may be used until its end of life for domestic transportation. For international transportation, instead, 15 years after the entry into force of this Commission Regulation, all vehicles shall be equipped with a compliant second generation smart tachograph, introduced by this Regulation.

This Annex contains second generation recording equipment and tachograph cards requirements. Starting from its introduction date, second generation recording equipment shall be installed in vehicles registered for the first time, and second generation tachograph cards shall be issued.

In order to foster a smooth introduction of the second generation tachograph system:


— second generation tachograph cards shall be designed to be also used in first generation vehicle units,
— replacement of valid first generation tachograph cards at the introduction date shall not be requested.

This will allow drivers to keep their unique driver card and use both systems with it.

Second generation recording equipment shall however only be calibrated using second generation workshop cards.

This Annex contains all requirements related to the interoperability between the first and the second generation tachograph system.

Appendix 15 contains additional details about how the coexistence of the two systems shall be managed.

1. 
In this Annex:


((a)) ‘activation’ means:
the phase in which the tachograph becomes fully operational and implements all functions, including security functions, through the use of a workshop card;
((b)) ‘authentication’ means:
a function intended to establish and verify a claimed identity;
((c)) ‘authenticity’ means:
the property that information is coming from a party whose identity can be verified;
((d)) ‘built-in test (BIT)’ means:
tests run at request, triggered by the operator or by external equipment;
((e)) ‘calendar day’ means:
a day ranging from 00:00 hours to 24:00 hours. All calendar days relate to UTC time (Universal Time Coordinated);
((f)) ‘calibration’ of a smart tachograph means:
updating or confirming vehicle parameters to be held in the data memory. Vehicle parameters include vehicle identification (VIN, VRN and registering Member State) and vehicle characteristics (w, k, l, tyre size, speed-limiting device setting (if applicable), current UTC time, current odometer value); during the calibration of a recording equipment, the types and identifiers of all type-approval relevant seals in place shall also be stored in the data memory;
any update or confirmation of UTC time only, shall be considered as a time adjustment and not as a calibration, provided it does not contradict Requirement 409;
calibrating recording equipment requires the use of a workshop card;
((g)) ‘card number’ means:
a 16-alphanumerical character number that uniquely identifies a tachograph card within a Member State. The card number includes a card consecutive index (if applicable), a card replacement index and a card renewal index;
a card is therefore uniquely identified by the code of the issuing Member State and the card number;
((h)) ‘card consecutive index’ means:
the 14th alphanumerical character of a card number that is used to differentiate the different cards issued to a company, a workshop or a control authority entitled to be issued several tachograph cards. The company, the workshop or the control authority is uniquely identified by the 13 first characters of the card number;
((i)) ‘card renewal index’ means:
the 16th alphanumerical character of a card number which is incremented each time a tachograph card is renewed;
((j)) ‘card replacement index’ means:
the 15th alpha-numerical character of a card number which is incremented each time a tachograph card is replaced;
((k)) ‘characteristic coefficient of the vehicle’ means:
the numerical characteristic giving the value of the output signal emitted by the part of the vehicle linking it with the recording equipment (gearbox output shaft or axle) while the vehicle travels a distance of one kilometre under standard test conditions as defined under requirement 414. The characteristic coefficient is expressed in impulses per kilometre (w = … imp/km);
((l)) ‘company card’ means:
a tachograph card issued by the authorities of a Member State to a transport undertaking needing to operate vehicles fitted with a tachograph, which identifies the transport undertaking and allows for the displaying, downloading and printing of the data, stored in the tachograph, which have been locked by that transport undertaking;
((m)) ‘constant of the recording equipment’ means:
the numerical characteristic giving the value of the input signal required to show and record a distance travelled of one kilometre; this constant shall be expressed in impulses per kilometre (k = … imp/km);
((n)) ‘continuous driving time’ is computed within the recording equipment as:
the continuous driving time is computed as the current accumulated driving times of a particular driver, since the end of his last AVAILABILITY or BREAK/REST or UNKNOWN period of 45 minutes or more (this period may have been split according to Regulation (EC) No 561/2006 of the European Parliament and of the Council). The computations involved take into account, as needed, past activities stored on the driver card. When the driver has not inserted his card, the computations involved are based on the data memory recordings related to the current period where no card was inserted and related to the relevant slot;
((o)) ‘control card’ means:
a tachograph card issued by the authorities of a Member State to a national competent control authority which identifies the control body and, optionally, the control officer, and which allows access to the data stored in the data memory or in the driver cards and, optionally, in the workshop cards for reading, printing and/or downloading;
It shall also give access to the roadside calibration checking function and to data on the remote early detection communication reader;
((p)) ‘cumulative break time’ is computed within the recording equipment as:
the cumulative break from driving time is computed as the current accumulated AVAILABILITY or BREAK/REST or UNKNOWN times of 15 minutes or more of a particular driver, since the end of his last AVAILABILITY or BREAK/REST or UNKNOWN period of 45 minutes or more (this period may have been split according to Regulation (EC) No 561/2006).
The computations involved take into account, as needed, past activities stored on the driver card. Unknown periods of negative duration (start of unknown period > end of unknown period) due to time overlaps between two different sets of recording equipment, are not taken into account for the computation.
When the driver has not inserted his card, the computations involved are based on the data memory recordings related to the current period where no card was inserted and related to the relevant slot;
((q)) ‘data memory’ means:
an electronic data storage device built into the recording equipment;
((r)) ‘digital signature’ means:
data appended to, or a cryptographic transformation of, a block of data that allows the recipient of the block of data to prove the authenticity and integrity of the block of data;
((s)) ‘downloading’ means:
the copying, together with the digital signature, of a part, or of a complete set, of data files recorded in the data memory of the vehicle unit or in the memory of a tachograph card, provided that this process does not alter or delete any stored data;
manufacturers of smart tachograph vehicle units and manufacturers of equipment designed and intended to download data files shall take all reasonable steps to ensure that the downloading of such data can be performed with the minimum delay by transport undertakings or drivers;
The downloading of the detailed speed file may not be necessary to establish compliance with Regulation (EC) No 561/2006, but may be used for other purposes such as accident investigation;
((t)) ‘driver card’ means:
a tachograph card, issued by the authorities of a Member State to a particular driver, which identifies the driver and allows for the storage of driver activity data;
((u)) ‘effective circumference of the wheels’ means:
the average of the distances travelled by each of the wheels moving the vehicle (driving wheels) in the course of one complete rotation. The measurement of these distances shall be made under standard test conditions as defined under requirement 414 and is expressed in the form ‘l = … mm’. Vehicle manufacturers may replace the measurement of these distances by a theoretical calculation which takes into account the distribution of the weight on the axles, vehicle unladen in normal running order. The methods for such theoretical calculation are subject to approval by a competent Member State authority and can take place only before tachograph activation;
((v)) ‘event’ means:
an abnormal operation detected by the smart tachograph which may result from a fraud attempt;
((w)) ‘external GNSS facility’ means
a facility which contains the GNSS receiver when the vehicle unit is not a single unit as well as other components needed to protect the communication of position data to the rest of the vehicle unit;
((x)) ‘fault’ means:
abnormal operation detected by the smart tachograph which may come from an equipment malfunction or failure;
((y)) ‘GNSS receiver’ means:
an electronic device that receives and digitally processes the signals from one or more Global Navigation Satellite System(s) (GNSS in English) in order to provide position, speed and time information;
((z)) ‘installation’ means:
the mounting of a tachograph in a vehicle;
((aa)) ‘interoperability’ means:
the capacity of systems and the underlying business processes to exchange data and to share information;
((bb)) ‘interface’ means:
a facility between systems which provides the media through which they can connect and interact;
((cc)) ‘position’ means:
geographical coordinates of the vehicle at a given time;
((dd)) ‘motion sensor’ means:
a part of the tachograph, providing a signal representative of vehicle speed and/or distance travelled;
((ee)) ‘non-valid card’ means:
a card detected as faulty, or which initial authentication failed, or whose start of validity date is not yet reached, or whose expiry date has passed;
((ff)) ‘open standard’ means:
a standard set out in a standard specification document available freely or at a nominal charge which it is permissible to copy, distribute or use for no fee or for a nominal fee;
((gg)) ‘out of scope’ means:
when the use of the recording equipment is not required, according to the provisions of Regulation (EC) No 561/2006;
((hh)) ‘over speeding’ means:
exceeding the authorised speed of the vehicle, defined as any period of more than 60 seconds during which the vehicle's measured speed exceeds the limit for setting the speed limitation device laid down in Council Directive 92/6/EEC, as last amended;
((ii)) ‘periodic inspection’ means:
a set of operations performed to check that the tachograph works properly, that its settings correspond to the vehicle parameters, and that no manipulation devices are attached to the tachograph;
((jj)) ‘printer’ means:
component of the recording equipment which provides printouts of stored data;
((kk)) ‘remote early detection communication’ means:
communication between the remote early detection communication facility and the remote early detection communication reader during targeted roadside checks with the aim of remotely detecting possible manipulation or misuse of recording equipment;
((ll)) ‘remote communication facility’ or ‘remote early detection facility’ means:
the equipment of the vehicle unit which is used to perform targeted roadside checks;
((mm)) ‘remote early detection communication reader’ means:
the system used by control officers for targeted roadside checks.
((nn)) ‘renewal’ means:
issue of a new tachograph card when an existing card reaches its expiry date, or is malfunctioning and has been returned to the issuing authority. Renewal always implies the certainty that two valid cards do not coexist;
((oo)) ‘repair’ means:
any repair of a motion sensor or of a vehicle unit or of a cable that requires the disconnection of its power supply, or its disconnection from other tachograph components, or the opening of the motion sensor or vehicle unit;
((pp)) ‘card replacement’ means:
issue of a tachograph card in replacement of an existing card, which has been declared lost, stolen or malfunctioning and has not been returned to the issuing authority. Replacement always implies a risk that two valid cards may coexist;
((qq)) ‘security certification’ means:
process to certify, by a common criteria certification body, that the recording equipment (or component) or the tachograph card under investigation fulfils the security requirements defined in the relative protection profiles;
((rr)) ‘self test’ means:
tests run cyclically and automatically by the recording equipment to detect faults;
((ss)) ‘time measurement’ means:
a permanent digital record of the coordinated universal date and time (UTC);
((tt)) ‘time adjustment’ means:
an adjustment of current time; this adjustment can be automatic at regular intervals, using the time provided by the GNSS receiver as a reference, or performed in calibration mode;
((uu)) ‘tyre size’ means:
the designation of the dimensions of the tyres (external driving wheels) in accordance with Council Directive 92/23/EEC as last amended;
((vv)) ‘vehicle identification’ means:
numbers identifying the vehicle: vehicle registration number (VRN) with indication of the registering Member State and vehicle identification number (VIN);
((ww)) for computing sake in the recording equipment ‘week’ means:
the period between 00:00 hours UTC on Monday and 24:00 UTC on Sunday;
((xx)) ‘workshop card’ means:
a tachograph card issued by the authorities of a Member State to designated staff of a tachograph manufacturer, a fitter, a vehicle manufacturer or a workshop, approved by that Member State, which identifies the cardholder and allows for the testing, calibration and activation of tachographs, and/or downloading from them;
((yy)) ‘adaptor’ means:
a device, providing a signal permanently representative of vehicle speed and/or distance travelled, other than the one used for the independent movement detection, and which is:

— installed and used only in M1 and N1 type vehicles (as defined in Annex II to Directive 2007/46/EC of the European Parliament and of the Council, as last amended),
— installed where it is not mechanically possible to install any other type of existing motion sensor which is otherwise compliant with the provisions of this Annex and its Appendixes 1 to 15,
— installed between the vehicle unit and where the speed/distance impulses are generated by integrated sensors or alternative interfaces,
— seen from a vehicle unit, the adaptor behaviour is the same as if a motion sensor, compliant with the provisions of this Annex and its Appendixes 1 to 16, was connected to the vehicle unit;
use of such an adaptor in those vehicles described above shall allow for the installation and correct use of a vehicle unit compliant with all the requirements of this Annex,
for those vehicles, the smart tachograph includes cables, an adaptor, and a vehicle unit;
((zz)) ‘data integrity’ means:
the accuracy and consistency of stored data, indicated by an absence of any alteration in data between two updates of a data record. Integrity implies that the data is an exact copy of the original version, e.g. that it has not been corrupted in the process of being written to, and read back from, a tachograph card or a dedicated equipment or during transmission via any communications channel;
((aaa)) ‘data privacy’ means:
the overall technical measures taken to ensure the proper implementation of the principles laid down in Directive 95/46/EC of the European Parliament and of the Council as well as of those laid down in Directive 2002/58/EC of the European Parliament and of the Council;
((bbb)) ‘smart tachograph’ system means:
the recording equipment, tachograph cards and the set of all directly or indirectly interacting equipment during their construction, installation, use, testing and control, such as cards, remote communication reader and any other equipment for data downloading, data analysis, calibration, generating, managing or introducing security elements, etc.;
((ccc)) ‘introduction date’:
36 months after the entry into force of the detailed provisions referred to in Article 11 of Regulation (EU) No 165/2014 of the European Parliament and of the Council
This is the date after which vehicles registered for the first time:

— shall be fitted with a tachograph connected to a positioning service based on a satellite navigation system,
— shall be able to communicate data for targeted roadside checks to competent control authorities while the vehicle is in motion,
— and may be equipped with standardised interfaces allowing the data recorded or produced by tachographs to be used in operational mode, by an external device.
((ddd)) ‘protection profile’ means:
a document used as part of certification process according Common Criteria, providing implementation independent specification of information assurance security requirements;
((eee)) ‘GNSS accuracy’:
in the context of recording the position from a Global Navigation Satellite System (GNSS) with tachographs, means the value of the horizontal dilution of precision (HDOP) calculated as the minimum of the HDOP values collected on the available GNSS systems;
((fff)) ‘accumulated driving time’ means:
a value representing the total accumulated number of minutes of driving of a particular vehicle.
The accumulated driving time value is a free running count of all minutes regarded as DRIVING by the monitoring of driving activities function of the recording equipment, and is only used for triggering the recording of the vehicle position, every time a multiple of three hours of accumulated driving is reached. The accumulation is started at the recording equipment activation. It is not affected by any other condition, like out of scope or ferry/train crossing.
The accumulated driving time value is not intended to be displayed, printed, or downloaded.

2.  2.1 
The purpose of the recording equipment is to record, store, display, print, and output data related to driver activities.

Any vehicle fitted with the recording equipment complying with the provisions of this Annex, must include a speed display and an odometer. These functions may be included within the recording equipment.
 (1) The recording equipment includes cables, a motion sensor, and a vehicle unit.
 (2) The interface between motion sensors and vehicle units shall comply with the requirements specified in Appendix 11.
 (3) The vehicle unit shall be connected to global navigation satellite system(s), as specified in Appendix 12.
 (4) The vehicle unit shall communicate with remote early detection communication readers, as specified in Appendix 14.
 (5) 
The recording equipment may be connected to other facilities through additional interfaces and/or through the optional ITS interface.
 (6) 
Recording equipment users identify themselves to the equipment via tachograph cards.
 (7) The recording equipment provides selective access rights to data and functions according to user's type and/or identity.

The recording equipment records and stores data in its data memory, in the remote communication facility and in tachograph cards.

This is done in accordance with Directive 95/46/EC of 24 October 1995 on the protection of individuals with regard to the processing of personal data and on the free movement of such data, with Directive 2002/58/EC of 12 July 2002 concerning the processing of personal data and the protection of privacy in the electronic communications sector and in compliance with Article 7 of Regulation (EU) No. 165/2014.
 2.2  (8) 

— monitoring cards insertions and withdrawals,
— speed, distance and position measurement,
— time measurement,
— monitoring driver activities,
— monitoring driving status,
— drivers manual entries:
— entry of places where daily work periods begin and/or end,
— manual entry of driver activities,
— entry of specific conditions,
— company locks management,
— monitoring control activities,
— detection of events and/or faults,
— built-in and self-tests,
— reading from data memory,
— recording and storing in data memory,
— reading from tachograph cards,
— recording and storing in tachograph cards,
— displaying,
— printing,
— warning,
— data downloading to external media,
— remote communication for targeted roadside checks,
— output data to additional facilities,
— calibration,
— roadside calibration check,
— time adjustment.
 2.3  (9) 

— operational mode,
— control mode,
— calibration mode,
— company mode.
 (10) 
Mode of operation Driver slot
No card Driver card Control card Workshop card Company card
Co-driver slot No card Operational Operational Control Calibration Company
Driver card Operational Operational Control Calibration Company
Control card Control Control Control Operational Operational
Workshop card Calibration Calibration Operational Calibration Operational
Company card Company Company Operational Operational Company
 (11) The recording equipment shall ignore non-valid cards inserted, except displaying, printing or downloading data held on an expired card which shall be possible.
 (12) 

— the calibration function is accessible in the calibration mode only,
— the roadside calibration checking function is accessible in the control mode only,
— the company locks management function is accessible in the company mode only,
— the monitoring of control activities function is operational in the control mode only,
— The downloading function is not accessible in the operational mode (except as provided for in requirement 193), and except downloading a driver card when no other card type is inserted into the VU.
 (13) 

— in the operational mode, any personal identification (surname and first name(s)) not corresponding to a tachograph card inserted shall be blanked and any card number not corresponding to a tachograph card inserted shall be partially blanked (every odd character — from left to right — shall be blanked),
— in the company mode, driver related data (requirements 102, 105 and 108) can be output only for periods where no lock exists or no other company holds a lock (as identified by the first 13 digits of the company card number),
— when no card is inserted in the recording equipment, driver related data can be output only for the current and 8 previous calendar days,
— personal data originating from the VU shall not be output through ITS interface of the VU unless the consent of the driver to whom the data relates is verified,
— the vehicle units have a normal operations validity period of 15 years, starting with the vehicle unit certificates effective date, but vehicle units can be used for additional 3 months, for data downloading only.
 2.4 
The system security aims at protecting the data memory in such a way as to prevent unauthorised access to and manipulation of the data and detecting any such attempts, protecting the integrity and authenticity of data exchanged between the motion sensor and the vehicle unit, protecting the integrity and authenticity of data exchanged between the recording equipment and the tachograph cards, protecting the integrity and authenticity of data exchanged between the vehicle unit and the external GNSS facility, if any, protecting the confidentiality, integrity and authenticity of data exchanged through the remote early detection communication for control purposes, and verifying the integrity and authenticity of data downloaded.
 (14) 

— vehicle unit,
— tachograph card,
— motion sensor,
— external GNSS facility (this Profile is only needed and applicable for the external GNSS variant).

3.  3.1  (15) The recording equipment shall monitor the card interface devices to detect card insertions and withdrawals.
 (16) 
If a card with the same card number and a higher renewal index has already been inserted in the recording equipment, the card shall be declared as non-valid.

If a card with the same card number and renewal index but with a higher replacement index has already been inserted in the recording equipment, the card shall be declared as non-valid.
 (17) First generation tachograph cards shall be considered as non-valid by the recording equipment, after the possibility of using first generation tachograph cards has been suppressed by a workshop, in compliance with Appendix 15 (req. MIG003).
 (18) First generation workshop cards which are inserted in the second generation recording equipment shall be considered as non-valid.
 (19) The recording equipment shall be so designed that the tachograph cards are locked in position on their proper insertion into the card interface devices.
 (20) The release of tachograph cards may function only when the vehicle is stopped and after the relevant data have been stored on the cards. The release of the card shall require positive action by the user.
 3.2  (21) The motion sensor (possibly embedded in the adaptor) is the main source for speed and distance measurement.
 (22) This function shall continuously measure and be able to provide the odometer value corresponding to the total distance travelled by the vehicle using the pulses provided by the motion sensor.
 (23) This function shall continuously measure and be able to provide the speed of the vehicle using the pulses provided by the motion sensor.
 (24) The speed measurement function shall also provide the information whether the vehicle is moving or stopped. The vehicle shall be considered as moving as soon as the function detects more than 1 imp/sec for at least 5 seconds from the motion sensor, otherwise the vehicle shall be considered as stopped.
 (25) Devices displaying speed (speedometer) and total distance travelled (odometer) installed in any vehicle fitted with a recording equipment complying with the provisions of this Regulation, shall comply with the requirements relating to maximum tolerances (see 3.2.1 and 3.2.2) laid down in this Annex.
 (26) To detect manipulation of motion data, information from the motion sensor shall be corroborated by vehicle motion information derived from the GNSS receiver and optionally by other source(s) independent from the motion sensor.
 (27) 

— positions where the driver and/or the co-driver begins his daily work period;
— positions where the accumulated driving time reaches a multiple of three hours;
— positions where the driver and/or the co-driver ends his daily work period.
 3.2.1  (28) 

— so as to cumulate both forward and reverse movements, or
— so as to include only forward movement.
 (29) The recording equipment shall measure distance from 0 to 9 999 999,9 km.
 (30) 

— ± 1 % before installation,
— ± 2 % on installation and periodic inspection,
— ± 4 % in use.
 (31) Distance measured shall have a resolution better than or equal to 0,1 km.
 3.2.2  (32) The recording equipment shall measure speed from 0 to 220 km/h.
 (33) 

— a ± 2 km/h tolerance for input variations (tyre variations, …),
— a ± 1 km/h tolerance in measurements made during installation or periodic inspections,

the recording equipment shall, for speeds between 20 and 180 km/h, and for characteristic coefficients of the vehicle between 4 000 and 25 000 imp/km, measure the speed with a tolerance of ± 1 km/h (at constant speed).
Note: The resolution of data storage brings an additional tolerance of ± 0,5 km/h to speed stored by the recording equipment. (34) The speed shall be measured correctly within the normal tolerances within 2 seconds of the end of a speed change when the speed has changed at a rate up to 2 m/s2.
 (35) Speed measurement shall have a resolution better than or equal to 1 km/h.
 3.2.3  (36) The recording equipment shall measure the absolute position of the vehicle using the GNSS receiver.
 (37) The absolute position is measured in geographical coordinates of latitude and longitude in degrees and minutes with a resolution of 1/10 of a minute.
 3.3  (38) The time measurement function shall measure permanently and digitally provide UTC date and time.
 (39) UTC date and time shall be used for dating data inside the recording equipment (recordings, data exchange) and for all printouts specified in Appendix 4 ‘Printouts’.
 (40) In order to visualise the local time, it shall be possible to change the offset of the time displayed, in half hour steps. No other offsets than negative or positive multiples of half hours shall be allowed;
 (41) Time drift shall be within ± 2 seconds per day in type approval conditions, in the absence of any time adjustment.
 (42) Time measured shall have a resolution better than or equal to 1 second.
 (43) Time measurement shall not be affected by an external power supply cut-off of less than 12 months in type approval conditions.
 3.4  (44) This function shall permanently and separately monitor the activities of one driver and one co-driver.
 (45) Driver activity shall be DRIVING, WORK, AVAILABILITY or BREAK/REST.
 (46) It shall be possible for the driver and/or the co-driver to manually select WORK, AVAILABILITY or BREAK/REST.
 (47) When the vehicle is moving, DRIVING shall be selected automatically for the driver and AVAILABILITY shall be selected automatically for the co-driver.
 (48) When the vehicle stops, WORK shall be selected automatically for the driver.
 (49) The first change of activity to BREAK/REST or AVAILABILITY arising within 120 seconds of the automatic change to WORK due to the vehicle stop shall be assumed to have happened at the time of vehicle stop (therefore possibly cancelling the change to WORK).
 (50) This function shall output activity changes to the recording functions at a resolution of one minute.
 (51) Given a calendar minute, if DRIVING is registered as the activity of both the immediately preceding and the immediately succeeding minute, the whole minute shall be regarded as DRIVING.
 (52) Given a calendar minute that is not regarded as DRIVING according to requirement 051, the whole minute shall be regarded to be of the same type of activity as the longest continuous activity within the minute (or the latest of the equally long activities).
 (53) This function shall also permanently monitor the continuous driving time and the cumulative break time of the driver.
 3.5  (54) This function shall permanently and automatically monitor the driving status.
 (55) The driving status CREW shall be selected when two valid driver cards are inserted in the equipment, the driving status SINGLE shall be selected in any other case.
 3.6  3.6.1  (56) This function shall allow for the entry of places where, according to the driver and/or the co-driver, his daily work periods begin and/or end.
 (57) Places are defined as the country and, in addition where applicable, the region, which are entered or confirmed manually.
 (58) At the time of a driver card withdrawal, the recording equipment shall prompt the (co-)driver to enter a ‘place where the daily work period ends’.
 (59) 
Under the following conditions temporary entry made at last card withdrawal is validated (i.e. shall not be overwritten anymore):


— entry of a place where the current daily work period begins during manual entry according to requirement (61);
— the next entry of a place where the current daily work period begins if the card holder doesn’t enter any place where the work period begins or ended during the manual entry according to requirement (61).

Under the following conditions temporary entry made at last card withdrawal is overwritten and the new value is validated:


— the next entry of a place where the current daily work period ends if the card holder doesn’t enter any place where the work period begins or ended during the manual input according to requirement (61).
 (60) It shall be possible to input places where daily work periods begin and/or end through commands in the menus. If more than one such input is done within one calendar minute, only the last begin place input and the last end place input done within that time shall be kept recorded.
 3.6.2  (61) 
At driver or workshop card insertion the cardholder shall be reminded of:


— the date and time of his last card withdrawal;
— optionally: the local time offset currently set for the vehicle unit.

At the first insertion of a given driver card or workshop card currently unknown to the vehicle unit, the cardholder shall be invited to express his consent for tachograph related personal data output through the optional ITS interface.

At any moment, the driver (resp. workshop) consent can be enabled or disabled through commands in the menu, provided the driver (resp. workshop) card is inserted.

It shall be possible to input activities with the following restrictions:


— Activity type shall be WORK, AVAILABILITY or BREAK/REST;
— Start and end times for each activity shall be within the period of the last card withdrawal — current insertion only;
— Activities shall not be allowed to overlap mutually in time.

It shall be possible to make manual entries, if required, at the first insertion of a previously unused driver (or workshop) card.

The procedure for manual entries of activities shall include as many consecutive steps as necessary to set a type, a start time and an end time for each activity. For any part of the time period between last card withdrawal and current card insertion, the cardholder shall have the option not to declare any activity.

During the manual entries associated with card insertion and if applicable, the card holder shall have the opportunity to input:


— a place where a previous daily work period ended, associated to the relevant time (thus overwriting and validating the entry made at the last card withdrawal),
— a place where the current daily work period begins, associated to the relevant time (thus validating a temporary entry made at last card withdrawal).

If the card holder doesn't enter any place where the work period begins or ended, during the manual entries associated with card insertion, this shall be considered as a declaration that his work period has not changed since the last card withdrawal. The next entry of a place where a previous daily work period ends shall then overwrite the temporary entry made at the last card withdrawal.

If a place is entered, it shall be recorded in the relevant tachograph card.

Manual entries shall be interrupted if:


— the card is withdrawn or,
— the vehicle is moving and the card is in the driver slot.

Additional interruptions are allowed, e.g. a timeout after a certain period of user inactivity. If manual entries are interrupted, the recording equipment shall validate any complete place and activity entries (having either unambiguous place and time, or activity type, begin time and end time) already made.

If a second driver or workshop card is inserted while manual entries of activities are in progress for a previously inserted card, the manual entries for this previous card shall be allowed to be completed before manual entries start for the second card.

The cardholder shall have the option to insert manual entries according to the following minimum procedure:


— Enter activities manually, in chronological order, for the period last card withdrawal — current insertion.
— Begin time of the first activity shall be set to card withdrawal time. For each subsequent entry, the start time shall be preset to immediately follow the end time of the previous entry. Activity type and end time shall be selected for each activity.

The procedure shall end when the end time of a manually entered activity equals the card insertion time. The recording equipment may then optionally allow the card holder to modify any activity manually entered, until validation by selection of a specific command. Thereafter, any such modification shall be forbidden.
 3.6.3  (62) 

— ‘OUT OF SCOPE’ (begin, end)
— ‘FERRY / TRAIN CROSSING’ (begin, end).

A ‘FERRY / TRAIN CROSSING’ may not occur if an ‘OUT OF SCOPE’ condition is opened.

An opened ‘OUT OF SCOPE’ condition must be automatically closed, by the recording equipment, if a driver card is inserted or withdrawn.

An opened ‘OUT OF SCOPE’ condition shall inhibit the following events and warnings:


— Driving without an appropriate card,
— Warnings associated with continuous driving time.

The FERRY / TRAIN CROSSING begin flag shall be set before shutting down the engine on the ferry/train.

An opened FERRY / TRAIN CROSSING must end when any of following options occurs:


— The driver manually ends the FERRY/TRAIN CROSSING
— The driver ejects his card

An opened FERRY/TRAIN CROSSING shall end when it is no longer valid based on the rules stated in Regulation (EC) No. 561/2006.
 3.7  (63) This function shall allow the management of the locks placed by a company to restrict data access in company mode to itself.
 (64) Company locks consist in a start date/time (lock-in) and an end date/time (lock-out) associated with the identification of the company as denoted by the company card number (at lock-in).
 (65) Locks may be turned ‘in’ or ‘out’ in real time only.
 (66) Locking-out shall only be possible for the company whose lock is ‘in’ (as identified by the first 13 digits of the company card number), or,
 (67) Locking-out shall be automatic if another company locks in.
 (68) In the case where a company locks in and where the previous lock was for the same company, then it will be assumed that the previous lock has not been turned ‘out’ and is still ‘in’.
 3.8  (69) This function shall monitor DISPLAYING, PRINTING, VU and card DOWNLOADING, and ROADSIDE CALIBRATION check activities carried while in control mode.
 (70) This function shall also monitor OVER SPEEDING CONTROL activities while in control mode. An over speeding control is deemed to have happened when, in control mode, the ‘over speeding’ printout has been sent to the printer or to the display, or when ‘events and faults’ data have been downloaded from the VU data memory.
 3.9  (71) This function shall detect the following events and/or faults:
 3.9.1  (72) This event shall be triggered at the insertion of any non-valid card, at the insertion of a driver card already replaced and/or when an inserted valid card expires.
 3.9.2  (73) 
Card conflict Driver slot
No card Driver card Control card Workshop card Company card
Co-driver slot No card     
Driver card    X 
Control card   X X X
Workshop card  X X X X
Company card   X X X 3.9.3  (74) This event shall be triggered when the date / time of last withdrawal of a driver card, as read from the card, is later than the current date / time of the recording equipment in which the card is inserted.
 3.9.4  (75) 
Driving without an appropriate card Driver slot
No (or non-valid) card Driver card Control card Workshop card Company card
Co-driver slot No (or non-valid) card X  X  X
Driver card X  X X X
Control card X X X X X
Workshop card X X X  X
Company card X X X X X 3.9.5  (76) This event shall be triggered when a tachograph card is inserted in any slot, while driver activity is DRIVING.
 3.9.6  (77) This event shall be triggered when at card insertion the recording equipment detects that, despite the provisions laid down in paragraph 3.1., the previous card session has not been correctly closed (the card has been withdrawn before all relevant data have been stored on the card). This event shall be triggered by driver and workshop cards only.
 3.9.7  (78) This event shall be triggered for each over speeding.
 3.9.8  (79) This event shall be triggered, while not in calibration or control mode, in case of any interruption exceeding 200 milliseconds of the power supply of the motion sensor and/or of the vehicle unit. The interruption threshold shall be defined by the manufacturer. The drop in power supply due to the starting of the engine of the vehicle shall not trigger this event.
 3.9.9  (80) This event shall be triggered, while not in calibration mode, when the remote communication facility does not acknowledge the successful reception of remote communication data sent from the vehicle unit for more than three attempts.
 3.9.10  (81) This event shall be triggered, while not in calibration mode, in case of absence of position information originating from the GNSS receiver (whether internal or external) for more than three hours of accumulated driving time.
 3.9.11  (82) This event shall be triggered, while not in calibration mode, in case of interruption of the communication between the external GNSS facility and the vehicle unit for more than 20 continuous minutes, when the vehicle is moving.
 3.9.12  (83) This event shall be triggered, while not in calibration mode, in case of interruption of the normal data flow between the motion sensor and the vehicle unit and/or in case of data integrity or data authentication error during data exchange between the motion sensor and the vehicle unit.
 3.9.13  (84) This event shall be triggered, while not in calibration mode, in case motion information calculated from the motion sensor is contradicted by motion information calculated from the internal GNSS receiver or from the external GNSS facility and optionally by other independent sources, as specified in Appendix 12. This event shall not be triggered during a ferry/train crossing, an OUT OF SCOPE condition, or when the position information from the GNSS receiver is not available.
 3.9.14  (85) This event shall be triggered for any other event affecting the security of the motion sensor and/or of the vehicle unit and/or the external GNSS facility as required in Appendix 10, while not in calibration mode.
 3.9.15  (86) This event shall be triggered, 
                                    while not in calibration mode
                                 , when the VU detects a discrepancy of more than 1 minute between the time of the vehicle unit’s time measurement function and the time originating from the GNSS receiver. This event is recorded together with the internal clock value of the vehicle unit and comes together with an automatic time adjustment. After a time conflict event has been triggered, the VU will not generate other time conflict events for the next 12 hours. This event shall not be triggered in cases where no valid GNSS signal was detectable by the GNSS receiver for 30 days or more.
 3.9.16  (87) This fault shall be triggered when a tachograph card failure occurs during operation.
 3.9.17  (88) 

— VU internal fault
— Printer fault
— Display fault
— Downloading fault
— Sensor fault
— GNSS receiver or external GNSS facility fault
— Remote Communication facility fault
— ITS interface fault (if applicable)
 3.10  (89) 
Sub-assembly to test Self-test Built-in-test
Software  Integrity
Data memory Access Access, data integrity
Card interface devices Access Access
Keyboard  Manual check
Printer (up to manufacturer) Printout
Display  Visual check
Downloading(performed only during downloading) Proper operation 
Sensor Proper operation Proper operation
Remote communication facility Proper operation Proper operation
GNSS facility Proper operation Proper operation
ITS interface (optional)
                                     
                                       Proper operation
                                      3.11  (90) The recording equipment shall be able to read any data stored in its data memory.
 3.12 
For the purpose of this paragraph,


— ‘365 days’ is defined as 365 calendar days of average drivers' activity in a vehicle. The average activity per day in a vehicle is defined as at least 6 drivers or co-drivers, 6 card insertion withdrawal cycles, and 256 activity changes. ‘365 days’ therefore include at least 2 190 (co-)drivers, 2 190 card insertion withdrawal cycles, and 93 440 activity changes,
— the average number of positions per day is defined as at least 6 positions where the daily work period begins, 6 positions when the accumulated driving time reaches a multiple of three hours, and 6 positions where the daily work period ends, so that ‘365 days’ include at least 6 570 positions,
— times are recorded with a resolution of one minute, unless otherwise specified,
— odometer values are recorded with a resolution of one kilometre,
— speeds are recorded with a resolution of 1 km/h,
— positions (latitudes and longitudes) are recorded in degrees and minutes, with a resolution of 1/10 of minute, with the associated GNSS accuracy and acquisition time.
 (91) Data stored into the data memory shall not be affected by an external power supply cut-off of less than twelve months in type approval conditions. In addition, data stored in the external remote communication facility, as defined in Appendix 14, shall not be affected by power-supply cut-off of less than 28 days.
 (92) The recording equipment shall be able to record and store implicitly or explicitly in its data memory the following:
 3.12.1  3.12.1.1  (93) 

— name of the manufacturer,
— address of the manufacturer,
— part number,
— serial number,
— VU generation,
— ability to use first generation tachograph cards,
— software version number,
— software version installation date,
— year of equipment manufacture,
— approval number,
 (94) Vehicle unit identification data are recorded and stored once and for all by the vehicle unit manufacturer, except the software related data and the approval number which may be changed in case of software upgrade and the ability to use first generation tachograph cards.
 3.12.1.2  (95) 

— name of the manufacturer,
— serial number,
— approval number,
— embedded security component identifier (e.g. internal chip/processor part number),
— operating system identifier (e.g. software version number).
 (96) Motion sensor identification data are recorded and stored once and for all in the motion sensor, by the motion sensor manufacturer.
 (97) 
The following data shall be recorded for each of these pairings:


— motion sensor identification data:
— serial number
— approval number
— motion sensor pairing data:
— pairing date.
 3.12.1.3  (98) 

— name of the manufacturer,
— serial number,
— approval number,
— embedded security component identifier (e.g. internal chip/processor part number),
— operating system identifier (e.g. software version number).
 (99) The identification data are recorded and stored once and for all in the external GNSS facility, by the external GNSS facility manufacturer.
 (100) 
The following data shall be recorded for each of these couplings:


— external GNSS facility identification data:
— serial number,
— approval number,
— external GNSS facility coupling data:
— coupling date
 3.12.2  (101) The recording equipment shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part A and part B.
 3.12.3  (102) 

— the card holder's surname and first name(s) as stored in the card,
— the card's number, issuing Member State and expiry date as stored in the card,
— the card generation,
— the insertion date and time,
— the vehicle odometer value at card insertion,
— the slot in which the card is inserted,
— the withdrawal date and time,
— the vehicle odometer value at card withdrawal,
— the following information about the previous vehicle used by the driver, as stored in the card:
— VRN and registering Member State,
— VU generation (when available),
— card withdrawal date and time,
— a flag indicating whether, at card insertion, the card holder has manually entered activities or not.
 (103) The data memory shall be able to hold these data for at least 365 days.
 (104) When storage capacity is exhausted, new data shall replace oldest data.
 3.12.4  (105) 

— the driving status (CREW, SINGLE),
— the slot (DRIVER, CO-DRIVER),
— the card status in the relevant slot (INSERTED, NOT INSERTED),
— the activity (DRIVING, AVAILABILITY, WORK, BREAK/REST),
— the date and time of the change.

INSERTED means that a valid driver or workshop card is inserted in the slot. NOT INSERTED means the opposite i.e. no valid driver or workshop card is inserted in the slot (e.g. a company card is inserted or no card is inserted)

Activity data manually entered by a driver are not recorded in the data memory.
 (106) The data memory shall be able to hold driver activity data for at least 365 days.
 (107) When storage capacity is exhausted, new data shall replace oldest data.
 3.12.5  (108) 

— places and positions where the driver and/or co-driver begins his daily work period;
— positions where the accumulated driving time reaches a multiple of three hours;
— places and positions where the driver and/or the co-driver ends his daily work period.
 (109) When the position of the vehicle is not available from the GNSS receiver at these times, the recording equipment shall use the latest available position, and the related date and time.
 (110) 

— the (co-)driver card number and card issuing Member State,
— the card generation,
— the date and time of the entry,
— the type of entry (begin, end or 3 hours accumulated driving time),
— the related GNSS accuracy, date and time if applicable;
— the vehicle odometer value.
 (111) The data memory shall be able to hold places and positions where daily work periods begin, end and/or where 3 hours accumulated driving time is reached for at least 365 days.
 (112) When storage capacity is exhausted, new data shall replace oldest data.
 3.12.6  (113) The recording equipment shall record in its data memory the vehicle odometer value and the corresponding date at midnight every calendar day.
 (114) The data memory shall be able to store midnight odometer values for at least 365 calendar days.
 (115) When storage capacity is exhausted, new data shall replace oldest data.
 3.12.7  (116) The recording equipment shall record and store in its data memory the instantaneous speed of the vehicle and the corresponding date and time at every second of at least the last 24 hours that the vehicle has been moving.
 3.12.8 
For the purpose of this subparagraph, time shall be recorded with a resolution of 1 second.
 (117) 
Event Storage rules Data to be recorded per event
Insertion of a non-valid card 
— the 10 most recent events. 
— date and time of event,
— card(s) type, number, issuing Member State and generation of the card creating the event.
— number of similar events that day
Card conflict 
— the 10 most recent events. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of the two cards creating the conflict.
Driving without an appropriate card 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Card insertion while driving 
— the last event for each of the 10 last days of occurrence, 
— date and time of the event,
— card(s) type, number, issuing Member State and generation,
— number of similar events that day
Last card session not correctly closed 
— the 10 most recent events. 
— date and time of card insertion,
— card(s) type, number, issuing Member State and generation,
— last session data as read from the card:
— date and time of card insertion,
— VRN, Member State of registration and VU generation.
Over speeding (1) 
— the most serious event for each of the 10 last days of occurrence (i.e. the one with the highest average speed),
— the 5 most serious events over the last 365 days.
— the first event having occurred after the last calibration 
— date and time of beginning of event,
— date and time of end of event,
— maximum speed measured during the event,
— arithmetic average speed measured during the event,
— card type, number, issuing Member State and generation of the driver card (if applicable),
— number of similar events that day.
Power supply interruption (2) 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Communication error with the remote communication facility 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Absence of position information from GNSS receiver 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Communication error with the external GNSS facility
                                        
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Motion data error 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Vehicle motion conflict 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Security breach attempt 
— the 10 most recent events per type of event. 
— date and time of beginning of event,
— date and time of end of event (if relevant),
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— type of event.
Time conflict
                                        
— the most serious event for each of the 10 last days of occurrence (i.e. the ones with the greatest difference between recording equipment date and time, and GNSS date and time).
— the 5 most serious events over the last 365 days. 
— recording equipment date and time
— GNSS date and time,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.

((1)) The recording equipment shall also record and store in its data memory:

— the date and time of the last OVER SPEEDING CONTROL,
— the date and time of the first over speeding following this OVER SPEEDING CONTROL,
— the number of over speeding events since the last OVER SPEEDING CONTROL.
((2)) These data may be recorded at power supply reconnection only, times may be known with an accuracy to the minute.
 3.12.9 
For the purpose of this subparagraph, time shall be recorded with a resolution of 1 second.
 (118) 
Fault Storage rules Data to be recorded per fault
Card fault 
— the 10 most recent driver card faults. 
— date and time of beginning of fault,
— date and time of end of fault,
— card(s) type, number, issuing Member State and generation.
Recording equipment faults 
— the 10 most recent faults for each type of fault,
— the first fault after the last calibration. 
— date and time of beginning of fault,
— date and time of end of fault,
— type of fault,
— card(s) type, number and issuing Member State and generation of any card inserted at beginning and/or end of the fault. 3.12.10  (119) 

— known calibration parameters at the moment of activation,
— its very first calibration following its activation,
— its first calibration in the current vehicle (as identified by its VIN),
— the 20 most recent calibrations (if several calibrations happen within one calendar day, only the first and the last one of the day shall be stored).
 (120) 

— purpose of calibration (activation, first installation, installation, periodic inspection),
— workshop name and address,
— workshop card number, card issuing Member State and card expiry date,
— vehicle identification,
— parameters updated or confirmed: w, k, l, tyre size, speed limiting device setting, odometer (old and new values), date and time (old and new values),
— the types and identifiers of all the seals in place.
 (121) In addition, the recording equipment shall record and store in its data memory its ability to use first generation tachograph cards (still activated or not).
 (122) 

— first pairing with a VU (date, time, VU approval number, VU serial number),
— last pairing with a VU (date, time, VU approval number, VU serial number).
 (123) 

— first coupling with a VU (date, time, VU approval number, VU serial number),
— last coupling with a VU (date, time, VU approval number, VU serial number).
 3.12.11  (124) 

— the most recent time adjustment,
— the 5 largest time adjustments.
 (125) 

— date and time, old value,
— date and time, new value,
— workshop name and address,
— workshop card number, card issuing Member State, card generation and card expiry date.
 3.12.12  (126) 

— date and time of the control,
— control card number, card issuing Member State and card generation,
— type of the control (displaying and/or printing and/or VU downloading and/or card downloading and/or roadside calibration checking).
 (127) In case of downloading, the dates of the oldest and of the most recent days downloaded shall also be recorded.
 3.12.13  (128) 

— lock-in date and time,
— lock-out date and time,
— company card number, card issuing Member State and card generation,
— company name and address.

Data previously locked by a lock removed from memory due to the limit above, shall be treated as not locked.
 3.12.14  (129) 

— date and time of downloading,
— company or workshop card number, card issuing Member State and card generation,
— company or workshop name.
 3.12.15  (130) 

— date and time of the entry,
— type of specific condition.
 (131) The data memory shall be able to hold specific conditions data for at least 365 days (with the assumption that on average, 1 condition is opened and closed per day). When storage capacity is exhausted, new data shall replace oldest data.
 3.12.16  (132) 

— the tachograph card number and its serial number,
— the manufacturer of the tachograph card,
— the tachograph card type,
— the tachograph card version.
 (133) The recording equipment shall be able to store at least 88 such records.
 3.13  (134) 

— to identify the card type, the card holder, the previously used vehicle, the date and time of the last card withdrawal and the activity selected at that time,
— to check that last card session was correctly closed,
— to compute the driver's continuous driving time, cumulative break time and cumulated driving times for the previous and the current week,
— to print requested printouts related to data recorded on a driver card,
— to download a driver card to external media.

This requirement only applies to first generation tachograph cards if their use has not been suppressed by a workshop.
 (135) In case of a reading error, the recording equipment shall try again, three times maximum, the same read command, and then if still unsuccessful, declare the card faulty and non-valid.
 3.14  3.14.1  (136) Provided first generation tachograph cards use has not been suppressed by a workshop, the recording equipment shall record and store data exactly in the same way as a first generation recording equipment would do.
 (137) The recording equipment shall set the ‘card session data’ in the driver or workshop card right after the card insertion.
 (138) The recording equipment shall update data stored on valid driver, workshop, company and/or control cards with all necessary data relevant to the period while the card is inserted and relevant to the card holder. Data stored on these cards are specified in Chapter 4.
 (139) The recording equipment shall update driver activity and places data (as specified in 4.5.3.1.9 and 4.5.3.1.11), stored on valid driver and/or workshop cards, with activity and places data manually entered by the cardholder.
 (140) All events not defined for the first generation recording equipment, shall not be stored on the driver and workshop cards.
 (141) Tachograph cards data update shall be such that, when needed and taking into account card actual storage capacity, most recent data replace oldest data.
 (142) In the case of a writing error, the recording equipment shall try again, three times maximum, the same write command and then if still unsuccessful, declare the card faulty and non-valid.
 (143) Before releasing a driver card and after all relevant data have been stored on the card, the recording equipment shall reset the ‘card session data’.
 3.14.2  (144) Second generation tachograph cards shall contain 2 different card applications, the first of which shall be exactly the same as the TACHO application of first generation tachograph cards, and the second the ‘TACHO_G2’ application, as specified in Chapter 4 and Appendix 2.
 (145) The recording equipment shall set the ‘card session data’ in the driver or workshop card right after the card insertion.
 (146) The recording equipment shall update data stored on the 2 card applications of valid driver, workshop, company and/or control cards with all necessary data relevant to the period while the card is inserted and relevant to the card holder. Data stored on these cards are specified in Chapter 4.
 (147) The recording equipment shall update driver activity places and positions data (as specified in 4.5.3.1.9, 4.5.3.1.11, 4.5.3.2.9 and 4.5.3.2.11), stored on valid driver and/or workshop cards, with activity and places data manually entered by the cardholder.
 (148) Tachograph cards data update shall be such that, when needed and taking into account card actual storage capacity, most recent data replace oldest data.
 (149) In the case of a writing error, the recording equipment shall try again, three times maximum, the same write command and then if still unsuccessful, declare the card faulty and non-valid.
 (150) Before releasing a driver card and after all relevant data have been stored on the 2 card applications of the card, the recording equipment shall reset the ‘card session data’.
 3.15  (151) The display shall include at least 20 characters.
 (152) The minimum character size shall be 5 mm high and 3.5 mm wide.
 (153) The display shall support the characters specified in Appendix 1 Chapter 4 ‘Character sets’. The display may use simplified glyphs (e.g. accented characters may be displayed without accent, or lower case letters may be shown as upper case letters).
 (154) The display shall be provided with adequate non-dazzling lighting.
 (155) Indications shall be visible from outside the recording equipment.
 (156) 

— default data,
— data related to warnings,
— data related to menu access,
— other data requested by a user.

Additional information may be displayed by the recording equipment, provided that it is clearly distinguishable from information required above.
 (157) The display of the recording equipment shall use the pictograms or pictograms combinations listed in Appendix 3. Additional pictograms or pictograms combinations may also be provided by the display, if clearly distinguishable from the aforementioned pictograms or pictograms combinations.
 (158) The display shall always be ON when the vehicle is moving.
 (159) 
Displaying format is specified in Appendix 5.
 3.15.1  (160) 

— the local time (as a result of UTC time + offset as set by the driver),
— the mode of operation,
— the current activity of the driver and the current activity of the co-driver,
— information related to the driver:
— if his current activity is DRIVING, his current continuous driving time and his current cumulative break time,
— if his current activity is not DRIVING, the current duration of this activity (since it was selected) and his current cumulative break time.
 (161) Display of data related to each driver shall be clear, plain and unambiguous. In the case where the information related to the driver and the co-driver cannot be displayed at the same time, the recording equipment shall display by default the information related to the driver and shall allow the user to display the information related to the co-driver.
 (162) In the case where the display width does not allow displaying by default the mode of operation, the recording equipment shall briefly display the new mode of operation when it changes.
 (163) The recording equipment shall briefly display the card holder name at card insertion.
 (164) When an ‘OUT OF SCOPE’ or FERRY/TRAIN condition is opened, then the default display must show using the relevant pictogram that the particular condition is opened (it is acceptable that the driver's current activity may not be shown at the same time).
 3.15.2  (165) The recording equipment shall display warning information using primarily the pictograms of Appendix 3, completed where needed by additional numerically coded information. A literal description of the warning may also be added in the driver's preferred language.
 3.15.3  (166) The recording equipment shall provide necessary commands through an appropriate menu structure.
 3.15.4  (167) 

— the UTC date and time, and local time offset,
— the content of any of the six printouts under the same formats as the printouts themselves,
— the continuous driving time and cumulative break time of the driver,
— the continuous driving time and cumulative break time of the co-driver,
— the cumulated driving time of the driver for the previous and the current week,
— the cumulated driving time of the co-driver for the previous and the current week,

optional:


— the current duration of co-driver activity (since it was selected),
— the cumulated driving time of the driver for current week,
— the cumulated driving time of the co-driver for the current daily work period,
— the cumulated driving time of the driver for the current daily work period.
 (168) 
Printout lines devoted to hand-written information may be omitted for display.
 3.16  (169) 

— driver activities from card daily printout,
— driver activities from Vehicle Unit daily printout,
— events and faults from card printout,
— events and faults from Vehicle Unit printout,
— technical data printout,
— over speeding printout.
— tachograph card data history for a given VU (see chapter 3.12.16)

The detailed format and content of these printouts are specified in Appendix 4.

Additional data may be provided at the end of the printouts.

Additional printouts may also be provided by the recording equipment, if clearly distinguishable from the seven aforementioned printouts.
 (170) The ‘driver activities from card daily printout’ and ‘Events and faults from card printout’ shall be available only when a driver card or a workshop card is inserted in the recording equipment. The recording equipment shall update data stored on the relevant card before starting printing.
 (171) 

— either automatically select the driver card or the workshop card if one only of these cards is inserted,
— or provide a command to select the source card or select the card in the driver slot if two of these cards are inserted in the recording equipment.
 (172) The printer shall be able to print 24 characters per line.
 (173) The minimum character size shall be 2.1 mm high and 1.5 mm wide.
 (174) The printer shall support the characters specified in Appendix 1 Chapter 4 ‘Character sets’.
 (175) Printers shall be so designed as to produce these printouts with a degree of definition likely to avoid any ambiguity when they are read.
 (176) Printouts shall retain their dimensions and recordings under normal conditions of humidity (10-90 %) and temperature.
 (177) The type approved paper used by the recording equipment shall bear the relevant type approval mark and an indication of the type(s) of recording equipment with which it may be used.
 (178) Printouts shall remain clearly legible and identifiable under normal conditions of storage, in terms of light intensity, humidity and temperature, for at least two years.
 (179) Printouts shall conform at least to the test specifications defined in Appendix 9.
 (180) It shall also be possible to add hand-written notes, such as the driver's signature, to these documents.
 (181) The recording equipment shall manage ‘paper out’ events while printing by, once paper has been re-loaded, restarting printing from printout beginning or by continuing printing and providing an unambiguous reference to previously printed part.
 3.17  (182) The recording equipment shall warn the driver when detecting any event and/or fault.
 (183) Warning of a power supply interruption event may be delayed until the power supply is reconnected.
 (184) The recording equipment shall warn the driver 15 minutes before and at the time of exceeding the maximum allowed continuous driving time.
 (185) Warnings shall be visual. Audible warnings may also be provided in addition to visual warnings.
 (186) Visual warnings shall be clearly recognisable by the user, shall be situated in the driver's field of vision and shall be clearly legible both by day and by night.
 (187) Visual warnings may be built into the recording equipment and/or remote from the recording equipment.
 (188) In the latter case it shall bear a ‘T’ symbol.
 (189) Warnings shall have a duration of at least 30 seconds, unless acknowledged by the user by hitting one or more specific keys of the recording equipment. This first acknowledgement shall not erase warning cause display referred to in next paragraph.
 (190) Warning cause shall be displayed on the recording equipment and remain visible until acknowledged by the user using a specific key or command of the recording equipment.
 (191) Additional warnings may be provided, as long as they do not confuse drivers in relation to previously defined ones.
 3.18  (192) The recording equipment shall be able to download on request data from its data memory or from a driver card to external storage media via the calibration/downloading connector. The recording equipment shall update data stored on the relevant card before starting downloading.
 (193) In addition and as an optional feature, the recording equipment may, in any mode of operation, download data through any another means to a company authenticated through this channel. In such a case, company mode data access rights shall apply to this download.
 (194) Downloading shall not alter or delete any stored data.
 (195) The calibration/downloading connector electrical interface is specified in Appendix 6.
 (196) Downloading protocols are specified in Appendix 7.
 3.19  (197) When the ignition is on, the Vehicle Unit shall store every 60 seconds in the remote communication facility the most recent data necessary for the purpose of targeted roadside checks. Such data shall be encrypted and signed as specified in Appendix 11 and Appendix 14.
 (198) Data to be checked remotely shall be available to remote communication readers through wireless communication, as specified in Appendix 14.
 (199) 

— the latest security breach attempt,
— the longest power supply interruption,
— sensor fault,
— motion data error,
— vehicle motion conflict,
— driving without a valid card,
— card insertion while driving,
— time adjustment data,
— calibration data including the dates of the two latest stored calibration records,
— vehicle registration number,
— speed recorded by the tachograph.
 3.20  (200) 
In Appendix 13, an optional ITS interface is specified and standardized. Other vehicle unit interfaces may co-exist, provided they fully comply with the requirements of Appendix 13 in term of minimum list of data, security and driver consent.

The driver consent doesn’t apply to data transmitted by the recording equipment to the vehicle network. In case the personal data injected in the vehicle network are further processed outside the vehicle network, it is the responsibility of the vehicle manufacturer to have that personal data process compliant with Regulation (EU) 2016/679 (‘General Data Protection Regulation’).

The driver consent doesn’t apply either to tachograph data downloaded to a remote company (requirement 193), as this scenario is monitored by the company card access right.

The following requirements apply to ITS data made available through that interface:


— these data are a set of selected existing data from the tachograph data dictionary (Appendix 1),
— a subset of these selected data are marked ‘personal data’,
— the subset of ‘personal data’ is only available if the verifiable consent of the driver, accepting his personal data can leave the vehicle network, is enabled,
— At any moment, the driver consent can be enabled or disabled through commands in the menu, provided the driver card is inserted,
— the set and subset of data will be broadcasted via Bluetooth wireless protocol in the radius of the vehicle cab, with a refresh rate of 1 minute,
— the pairing of the external device with the ITS interface will be protected by a dedicated and random PIN of at least 4 digits, recorded in and available through the display of each vehicle unit,
— in any circumstances, the presence of the ITS interface cannot disturb or affect the correct functioning and the security of the vehicle unit.

Other data may also be output in addition to the set of selected existing data, considered as the minimum list, provided they cannot be considered as personal data.

The recording equipment shall have the capacity to communicate the driver consent status to other platforms in the vehicle network.

When the ignition of the vehicle is ON, these data shall be permanently broadcasted.
 (201) The serial link interface as specified in Annex 1B to Regulation (EEC) No. 3821/85, as last amended, can continue to equip tachographs for back compatibility. Anyhow, the driver consent is still required in case personal data are transmitted.
 3.21  (202) 

— to automatically pair the motion sensor with the VU,
— to automatically couple the external GNSS facility with the VU if applicable,
— to digitally adapt the constant of the recording equipment (k) to the characteristic coefficient of the vehicle (w),
— to adjust the current time within the validity period of the inserted workshop card,
— to adjust the current odometer value,
— to update motion sensor identification data stored in the data memory,
— to update, if applicable, external GNSS facility identification data stored in the data memory,
— to update the types and identifiers of all the seals in place,
— to update or confirm other parameters known to the recording equipment: vehicle identification, w, l, tyre size and speed limiting device setting if applicable.
 (203) In addition, the calibration function shall allow to supress the use of first generation tachograph cards in the recording equipment, provided the conditions specified in Appendix 15 are met.
 (204) 

— updating motion sensor installation data held by the motion sensor (as needed),
— copying from the motion sensor to the VU data memory the necessary motion sensor identification data.
 (205) 

— updating external GNSS facility installation data held by the external GNSS facility (as needed),
— copying from the external GNSS facility to the VU data memory the necessary external GNSS facility identification data including the serial number of the external GNSS facility,

The coupling shall be followed by the verification of the GNSS position information.
 (206) The calibration function shall be able to input necessary data through the calibration/downloading connector in accordance with the calibration protocol defined in Appendix 8. The calibration function may also input necessary data through other means.
 3.22  (207) The roadside calibration checking function shall allow reading the motion sensor serial number (possibly embedded in the adaptor) and the external GNSS facility serial number (when applicable), connected to the vehicle unit, at the time of the request.
 (208) This reading shall at least be possible on the vehicle unit display through commands in the menus.
 (209) The roadside calibration checking function shall also allow controlling the selection of the I/O mode of the calibration I/O signal line specified in Appendix 6, via the K-line interface. This shall be done through the ECUAdjustmentSession, as specified in Appendix 8, section 7 Control of Test Pulses — Input output control functional unit.
 3.23  (210) The time adjustment function shall allow for automatically adjusting the current time. Two time sources are used in the recording equipment for time adjustment: 1) the internal VU clock, 2) the GNSS receiver.
 (211) The time setting of the VU internal clock shall be automatically re-adjusted every 12 hours. When this re-adjustment is not possible because the GNSS signal is not available, the time setting shall be done as soon as the VU can access a valid time provided by GNSS receiver, according to the vehicle ignition conditions. The time reference for the automatic time setting of the VU internal clock shall be derived from the GNSS receiver.
 (212) The time adjustment function shall also allow for triggered adjustment of the current time, in calibration mode.
 3.24  (213) The Vehicle Unit shall be fully operational in the temperature range – 20 °C to 70 °C, the external GNSS facility in the temperature range – 20 °C to 70 °C, and the motion sensor in the temperature range – 40 °C to 135 °C. Data memory content shall be preserved at temperatures down to – 40 °C.
 (214) The tachograph shall be fully operational in the humidity range 10 % to 90 %.
 (215) The seals used in the smart tachograph shall withstand the same conditions than those applicable to the tachograph components to which they are affixed.
 (216) The recording equipment shall be protected against over-voltage, inversion of its power supply polarity, and short circuits.
 (217) 

— react to a magnetic field disturbing vehicle motion detection. In such circumstances, the vehicle unit will record and store a sensor fault (requirement 88) or,
— have a sensing element that is protected from, or immune to, magnetic fields.
 (218) The recording equipment and the external GNSS facility shall conform to international regulation UN ECE R10 and shall be protected against electrostatic discharges and transients.
 3.25  (219) All the constituent parts of the recording equipment shall be made of materials of sufficient stability and mechanical strength and with stable electrical and magnetic characteristics.
 (220) For normal conditions of use, all the internal parts of the equipment shall be protected against damp and dust.
 (221) The Vehicle Unit and the external GNSS facility shall meet the protection grade IP 40 and the motion sensor shall meet the protection grade IP 64, as per standard IEC 60529:1989 including A1:1999 and A2:2013.
 (222) The recording equipment shall conform to applicable technical specifications related to ergonomic design.
 (223) The recording equipment shall be protected against accidental damage.
 3.26  (224) 

— near the figure indicating the distance, the unit of measurement of distance, indicated by the abbreviation ‘km’,
— near the figure showing the speed, the entry ‘km/h’.

The recording equipment may also be switched to display the speed in miles per hour, in which case the unit of measurement of speed shall be shown by the abbreviation ‘mph’. The recording equipment may also be switched to display the distance in miles, in which case the unit of measurement of distance shall be shown by the abbreviation ‘mi’.
 (225) 

— name and address of the manufacturer,
— manufacturer's part number and year of manufacture,
— serial number,
— type-approval mark.
 (226) When physical space is not sufficient to show all above mentioned details, the descriptive plaque shall show at least: the manufacturer's name or logo and the part number.

4.  4.1 
The front page shall contain:
 (227) the words ‘Driver card’ or ‘Control card’ or ‘Workshop card’ or ‘Company card’ printed in capital letters in the official language or languages of the Member State issuing the card, according to the type of the card.
 (228) the name of the Member State issuing the card (optional);
 (229) 
BBGCZCY BelgiumBulgariaCzech RepublicCyprus LVLLTM LatviaLuxembourgLithuaniaMalta
DK Denmark NL The Netherlands
DEST GermanyEstonia APL AustriaPoland
GR Greece PROSKSLO PortugalRomaniaSlovakiaSlovenia
E Spain FIN Finland
FHRH FranceCroatiaHungary S Sweden
IRL Ireland UK The United Kingdom
I Italy   (230) 
 Driver card Control Card Company or Workshop card
1. surname of the driver control body name company or workshop name
2. first name(s) of the driver surname of the controller(if applicable) surname of card holder(if applicable)
3. birth date of the driver first name(s) of the controller(if applicable) first name(s) of card holder(if applicable)
4.a card start of validity date
4.b card expiry date
4.c the name of the issuing authority (may be printed on reverse page)
4.d a different number from the one under heading 5, for administrative purposes (optional)
5. a Driving licence number(at the date of issue of the driver card) — —
5. b Card number
6. Photograph of the driver photograph of the controller (optional) photograph of the fitter (optional)-
7. Signature of the holder (optional)
8. Normal place of residence, or postal address of the holder (optional). Postal address of control body postal address of company or workshop (231) dates shall be written using a ‘dd/mm/yyyy’ or ‘dd.mm.yyyy’ format (day, month, year).

The reverse page shall contain:
 (232) an explanation of the numbered items which appear on the front page of the card;
 (233) with the specific written agreement of the holder, information which is not related to the administration of the card may also be added, such addition will not alter in any way the use of the model as a tachograph card.
 (234) 
— driver cardwhite,— control cardblue,— workshop cardred,— company cardyellow.
 (235) 

— a security design background with fine guilloche patterns and rainbow printing,
— in the area of the photograph, the security design background and the photograph shall overlap,
— at least one two-coloured microprint line.


 (236) After consulting the Commission, Member States may add colours or markings, such as national symbols and security features, without prejudice to the other provisions of this Annex.
 (237) Temporary cards referred to in Article 26.4 of Regulation (EU) No. 165/2014 shall comply with the provisions of this Annex.
 4.2 
The system security aims at protecting integrity and authenticity of data exchanged between the cards and the recording equipment, protecting the integrity and authenticity of data downloaded from the cards, allowing certain write operations onto the cards to recording equipment only, decrypting certain data, ruling out any possibility of falsification of data stored in the cards, preventing tampering and detecting any attempt of that kind.
 (238) In order to achieve the system security, the tachograph cards shall meet the security requirements defined in Appendixes 10 and 11.
 (239) Tachograph cards shall be readable by other equipment such as personal computers.
 4.3  (240) 

— ISO/IEC 7810 Identification cards — Physical characteristics,
— ISO/IEC 7816 Identification cards — Integrated circuit cards:
— Part 1: Physical characteristics,
— Part 2: Dimensions and position of the contacts (ISO/IEC 7816-2:2007),
— Part 3: Electrical interface and transmission protocols (ISO/IEC 7816-3:2006),
— Part 4: Organisation, security and commands for interchange (ISO/IEC 7816-4:2013 + Cor 1:2014),
— Part 6: Interindustry data elements for interchange (ISO/IEC 7816-6:2004 + Cor 1:2006),
— Part 8: Commands for security operations (ISO/IEC 7816-8:2004).
— Tachograph cards shall be tested in accordance to ISO/IEC 10373-3:2010 Identification cards — Test methods — Part 3: Integrated circuit cards with contacts and related interface devices.
 4.4  (241) Tachograph cards shall be capable of operating correctly in all the climatic conditions normally encountered in Community territory and at least in the temperature range – 25 °C to + 70 °C with occasional peaks of up to + 85 °C, ‘occasional’ meaning not more than 4 hours each time and not over 100 times during the life time of the card.
 (242) Tachograph cards shall be capable of operating correctly in the humidity range 10 % to 90 %.
 (243) Tachograph cards shall be capable of operating correctly for a five-year period if used within the environmental and electrical specifications.
 (244) During operation, tachograph cards shall conform to ECE R10, related to electromagnetic compatibility, and shall be protected against electrostatic discharges.
 4.5 
For the purpose of this paragraph,


— times are recorded with a resolution of one minute, unless otherwise specified,
— odometer values are recorded with a resolution of one kilometre,
— speeds are recorded with a resolution of 1 km/h,
— positions (latitudes and longitudes) are recorded in degrees and minutes with a resolution of 1/10 of minute.

The tachograph cards functions, commands and logical structures, fulfilling data storage requirements are specified in Appendix 2.

If not otherwise specified, data storage on tachograph cards shall be organized in such a way, that new data replaces stored oldest data in case the foreseen memory size for the particular records is exhausted.
 (245) This paragraph specifies minimum storage capacity for the various application data files. Tachograph cards shall be able to indicate to the recording equipment the actual storage capacity of these data files.
 (246) Any additional data that may be stored on tachograph cards, related to other applications possibly borne by the card, shall be stored in accordance with Directive 95/46/EC and with Directive 2002/58/EC and in compliance with Article 7 of Regulation (EU) No. 165/2014.
 (247) 

— DF Tachograph, which contains the application accessible to first generation vehicle units, which is also present in first generation tachograph cards,
— DF Tachograph_G2, which contains the application only accessible to second generation vehicle units, which is only present in second generation tachograph cards.

The full details of the tachograph cards structure are specified in Appendix 2.
 4.5.1  4.5.2  (248) 

— clock stop,
— card serial number (including manufacturing references),
— card type approval number,
— card personaliser identification (ID),
— embedder ID,
— IC identifier.
 4.5.2.1  (249) 

— IC serial number,
— IC manufacturing references.
 4.5.2.2  (250) Tachograph cards shall be able to store the application identification data objects specified in Appendix 2.
 4.5.2.3  (251) 

— in the case the tachograph card supports extended length fields, the extended length information data object specified in Appendix 2.
 4.5.2.4  (252) 

— in the case the tachograph card supports extended length fields, the extended length information data objects specified in Appendix 2.
 4.5.3  4.5.3.1  4.5.3.1.1  (253) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.3.1.2  (254) The driver card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part A.
 4.5.3.1.3  (255) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date.
 4.5.3.1.4  (256) 

— surname of the holder,
— first name(s) of the holder,
— date of birth,
— preferred language.
 4.5.3.1.5  (257) 

— date and time of last card download (for other purposes than control).
 (258) The driver card shall be able to hold one such record.
 4.5.3.1.6  (259) 

— issuing Member State, issuing authority name,
— driving licence number (at the date of the issue of the card).
 4.5.3.1.7 
For the purpose of this subparagraph, time shall be stored with a resolution of 1 second.
 (260) 

— Time overlap (where this card is the cause of the event),
— Card insertion while driving (where this card is the subject of the event),
— Last card session not correctly closed (where this card is the subject of the event),
— Power supply interruption,
— Motion data error,
— Security breach attempts.
 (261) 

— Event code,
— Date and time of beginning of the event (or of card insertion if the event was on-going at that time),
— Date and time of end of the event (or of card withdrawal if the event was on-going at that time),
— VRN and registering Member State of vehicle in which the event happened.
Note: For the ‘Time overlap’ event:
— Date and time of beginning of the event shall correspond to the date and time of the card withdrawal from the previous vehicle,
— Date and time of end of the event shall correspond to the date and time of card insertion in current vehicle,
— Vehicle data shall correspond to the current vehicle raising the event.Note: For the ‘Last card session not correctly closed’ event:
— date and time of beginning of event shall correspond to the card insertion date and time of the session not correctly closed,
— date and time of end of event shall correspond to the card insertion date and time of the session during which the event was detected (current session),
— Vehicle data shall correspond to the vehicle in which the session was not correctly closed. (262) The driver card shall be able to store data for the six most recent events of each type (i.e. 36 events).
 4.5.3.1.8 
For the purpose of this subparagraph, time shall be recorded with a resolution of 1 second.
 (263) 

— Card fault (where this card is the subject of the fault),
— Recording equipment fault.
 (264) 

— Fault code,
— Date and time of beginning of the fault (or of card insertion if the fault was on-going at that time),
— Date and time of end of the fault (or of card withdrawal if the fault was on-going at that time),
— VRN and registering Member State of vehicle in which the fault happened.
 (265) The driver card shall be able to store data for the twelve most recent faults of each type (i.e. 24 faults).
 4.5.3.1.9  (266) 

— the date,
— a daily presence counter (increased by one for each of these calendar days),
— the total distance travelled by the driver during this day,
— a driver status at 00:00,
— whenever the driver has changed of activity, and/or has changed of driving status, and/or has inserted or withdrawn his card:
— the driving status (CREW, SINGLE),
— the slot (DRIVER, CO-DRIVER),
— the card status (INSERTED, NOT INSERTED),
— the activity (DRIVING, AVAILABILITY, WORK, BREAK/REST),
— the time of the change.
 (267) The driver card memory shall be able to hold driver activity data for at least 28 days (the average activity of a driver is defined as 93 activity changes per day).
 (268) The data listed under requirements 261, 264 and 266 shall be stored in a way allowing the retrieval of activities in the order of their occurrence, even in case of a time overlap situation.
 4.5.3.1.10  (269) 

— date and time of first use of the vehicle (i.e. first card insertion for this period of use of the vehicle, or 00h00 if the period of use is on-going at that time),
— vehicle odometer value at that time,
— date and time of last use of the vehicle, (i.e. last card withdrawal for this period of use of the vehicle, or 23h59 if the period of use is on-going at that time),
— vehicle odometer value at that time,
— VRN and registering Member State of the vehicle.
 (270) The driver card shall be able to store at least 84 such records.
 4.5.3.1.11  (271) 

— the date and time of the entry (or the date/time related to the entry if the entry is made during the manual entry procedure),
— the type of entry (begin or end, condition of entry),
— the country and region entered,
— the vehicle odometer value.
 (272) The driver card memory shall be able to hold at least 42 pairs of such records.
 4.5.3.1.12  (273) 

— date and time the session was opened (i.e. card insertion) with a resolution of one second,
— VRN and registering Member State.
 4.5.3.1.13  (274) 

— date and time of the control,
— control card number and card issuing Member State,
— type of the control (displaying and/or printing and/or VU downloading and/or card downloading (see note)),
— Period downloaded, in case of downloading,
— VRN and registering Member State of the vehicle in which the control happened.
Note: card downloading will only be recorded if performed through a recording equipment. (275) The driver card shall be able to hold one such record.
 4.5.3.1.14  (276) 

— Date and time of the entry,
— Type of specific condition.
 (277) The driver card shall be able to store at least 56 such records.
 4.5.3.2  4.5.3.2.1  (278) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.3.2.2  (279) The driver card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part B.
 4.5.3.2.3  (280) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date.
 4.5.3.2.4  (281) 

— surname of the holder,
— first name(s) of the holder,
— date of birth,
— preferred language.
 4.5.3.2.5  (282) 

— date and time of last card download (for other purposes than control).
 (283) The driver card shall be able to hold one such record.
 4.5.3.2.6  (284) 

— issuing Member State, issuing authority name,
— driving licence number (at the date of the issue of the card).
 4.5.3.2.7 
For the purpose of this subparagraph, time shall be stored with a resolution of 1 second.
 (285) 

— Time overlap (where this card is the cause of the event),
— Card insertion while driving (where this card is the subject of the event),
— Last card session not correctly closed (where this card is the subject of the event),
— Power supply interruption,
— Communication error with the remote communication facility,
— Absence of position information from GNSS receiver event,
— Communication error with the external GNSS facility
— Motion data error,
— Vehicle motion conflict,
— Security breach attempts,
— Time conflict.
 (286) 

— Event code,
— Date and time of beginning of the event (or of card insertion if the event was on-going at that time),
— Date and time of end of the event (or of card withdrawal if the event was on-going at that time),
— VRN and registering Member State of vehicle in which the event happened.
Note: For the ‘Time overlap’ event:
— Date and time of beginning of the event shall correspond to the date and time of the card withdrawal from the previous vehicle,
— Date and time of end of the event shall correspond to the date and time of card insertion in current vehicle,
— Vehicle data shall correspond to the current vehicle raising the event.Note: For the ‘Last card session not correctly closed’ event:
— date and time of beginning of event shall correspond to the card insertion date and time of the session not correctly closed,
— date and time of end of event shall correspond to the card insertion date and time of the session during which the event was detected (current session),
— Vehicle data shall correspond to the vehicle in which the session was not correctly closed. (287) The driver card shall be able to store data for the six most recent events of each type (i.e. 66 events).
 4.5.3.2.8 
For the purpose of this subparagraph, time shall be recorded with a resolution of 1 second.
 (288) 

— Card fault (where this card is the subject of the fault),
— Recording equipment fault.
 (289) 

— Fault code,
— Date and time of beginning of the fault (or of card insertion if the fault was on-going at that time),
— Date and time of end of the fault (or of card withdrawal if the fault was on-going at that time),
— VRN and registering Member State of vehicle in which the fault happened.
 (290) The driver card shall be able to store data for the twelve most recent faults of each type (i.e. 24 faults).
 4.5.3.2.9  (291) 

— the date,
— a daily presence counter (increased by one for each of these calendar days),
— the total distance travelled by the driver during this day,
— a driver status at 00:00,
— whenever the driver has changed of activity, and/or has changed of driving status, and/or has inserted or withdrawn his card:
— the driving status (CREW, SINGLE)
— the slot (DRIVER, CO-DRIVER),
— the card status (INSERTED, NOT INSERTED),
— the activity (DRIVING, AVAILABILITY, WORK, BREAK/REST).
— the time of the change,
 (292) The driver card memory shall be able to hold driver activity data for at least 28 days (the average activity of a driver is defined as 93 activity changes per day).
 (293) The data listed under requirements 286, 289 and 291 shall be stored in a way allowing the retrieval of activities in the order of their occurrence, even in case of a time overlap situation.
 4.5.3.2.10  (294) 

— date and time of first use of the vehicle (i.e. first card insertion for this period of use of the vehicle, or 00h00 if the period of use is on-going at that time),
— vehicle odometer value at that first use time,
— date and time of last use of the vehicle, (i.e. last card withdrawal for this period of use of the vehicle, or 23h59 if the period of use is on-going at that time),
— vehicle odometer value at that last use time,
— VRN and registering Member State of the vehicle,
— VIN of the vehicle.
 (295) The driver card shall be able to store at least 84 such records.
 4.5.3.2.11  (296) 

— the date and time of the entry (or the date/time related to the entry if the entry is made during the manual entry procedure),
— the type of entry (begin or end, condition of entry),
— the country and region entered,
— the vehicle odometer value,
— the vehicle position,
— the GNSS accuracy, date and time when the position was determined.
 (297) The driver card memory shall be able to hold at least 84 pairs of such records.
 4.5.3.2.12  (298) 

— date and time the session was opened (i.e. card insertion) with a resolution of one second,
— VRN and registering Member State.
 4.5.3.2.13  (299) 

— date and time of the control,
— control card number and card issuing Member State,
— type of the control (displaying and/or printing and/or VU downloading and/or card downloading (see note)),
— Period downloaded, in case of downloading,
— VRN and registering Member State of the vehicle in which the control happened.
Note: security requirements imply that card downloading will only be recorded if performed through a recording equipment. (300) The driver card shall be able to hold one such record.
 4.5.3.2.14  (301) 

— Date and time of the entry,
— Type of specific condition.
 (302) The driver card shall be able to store at least 56 such records.
 4.5.3.2.15  (303) 

— the date and time of the beginning of the period of use of the vehicle unit (i.e. first card insertion in the vehicle unit for the period),
— the manufacturer of the vehicle unit,
— the vehicle unit type,
— the vehicle unit software version number.
 (304) The driver card shall be able to store at least 84 such records.
 4.5.3.2.16  (305) 

— the date and time when the accumulated driving time reaches a multiple of three hours,
— the position of the vehicle,
— the GNSS accuracy, date and time when the position was determined,
— the vehicle odometer value.
 (306) The driver card shall be able to store at least 252 such records.
 4.5.4  4.5.4.1  4.5.4.1.1  (307) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.4.1.2  (308) The workshop card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part A.
 (309) The workshop card shall be able to store a Personal Identification Number (PIN code).
 4.5.4.1.3  (310) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date.
 4.5.4.1.4  (311) 

— workshop name,
— workshop address,
— surname of the holder,
— first name(s) of the holder,
— preferred language.
 4.5.4.1.5  (312) The workshop card shall be able to store a card download data record in the same manner as a driver card.
 4.5.4.1.6  (313) The workshop card shall be able to hold records of calibrations and/or time adjustments performed while the card is inserted in a recording equipment.
 (314) 

— Purpose of calibration (activation, first installation, installation, periodic inspection,),
— Vehicle identification,
— Parameters updated or confirmed (w, k, l, tyre size, speed limiting device setting, odometer (new and old values), date and time (new and old values)),
— Recording equipment identification (VU part number, VU serial number, motion sensor serial number).
 (315) The workshop card shall be able to store at least 88 such records.
 (316) The workshop card shall hold a counter indicating the total number of calibrations performed with the card.
 (317) The workshop card shall hold a counter indicating the number of calibrations performed since its last download.
 4.5.4.1.7  (318) The workshop card shall be able to store events and faults data records in the same manner as a driver card.
 (319) The workshop card shall be able to store data for the three most recent events of each type (i.e. 18 events) and the six most recent faults of each type (i.e. 12 faults).
 4.5.4.1.8  (320) The workshop card shall be able to store driver activity data in the same manner as a driver card.
 (321) The workshop card shall be able to hold driver activity data for at least 1 day of average driver activity.
 4.5.4.1.9  (322) The workshop card shall be able to store vehicles used data records in the same manner as a driver card.
 (323) The workshop card shall be able to store at least 4 such records.
 4.5.4.1.10  (324) The workshop card shall be able to store daily works period start and/or end data records in the same manner as a driver card.
 (325) The workshop card shall be able to hold at least 3 pairs of such records.
 4.5.4.1.11  (326) The workshop card shall be able to store a card session data record in the same manner as a driver card.
 4.5.4.1.12  (327) The workshop card shall be able to store a control activity data record in the same manner as a driver card.
 4.5.4.1.13  (328) The workshop card shall be able to store data relevant to specific conditions in the same manner as the driver card.
 (329) The workshop card shall be able to store at least 2 such records.
 4.5.4.2  4.5.4.2.1  (330) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.4.2.2  (331) The workshop card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part B.
 (332) The workshop card shall be able to store a Personal Identification Number (PIN code).
 4.5.4.2.3  (333) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date.
 4.5.4.2.4  (334) 

— workshop name,
— workshop address,
— surname of the holder,
— first name(s) of the holder,
— preferred language.
 4.5.4.2.5  (335) The workshop card shall be able to store a card download data record in the same manner as a driver card.
 4.5.4.2.6  (336) The workshop card shall be able to hold records of calibrations and/or time adjustments performed while the card is inserted in a recording equipment.
 (337) 

— purpose of calibration (activation, first installation, installation, periodic inspection,),
— vehicle identification,
— parameters updated or confirmed (w, k, l, tyre size, speed limiting device setting, odometer (new and old values), date and time (new and old values),
— recording equipment identification (VU part number, VU serial number, motion sensor serial number, remote communication facility serial number and external GNSS facility serial number, if applicable),
— seal type and identifier of all seals in place,
— ability of the VU to use first generation tachograph cards (enabled or not).
 (338) The workshop card shall be able to store at least 88 such records.
 (339) The workshop card shall hold a counter indicating the total number of calibrations performed with the card.
 (340) The workshop card shall hold a counter indicating the number of calibrations performed since its last download.
 4.5.4.2.7  (341) The workshop card shall be able to store events and faults data records in the same manner as a driver card.
 (342) The workshop card shall be able to store data for the three most recent events of each type (i.e. 33 events) and the six most recent faults of each type (i.e. 12 faults).
 4.5.4.2.8  (343) The workshop card shall be able to store driver activity data in the same manner as a driver card.
 (344) The workshop card shall be able to hold driver activity data for at least 1 day of average driver activity.
 4.5.4.2.9  (345) The workshop card shall be able to store vehicles used data records in the same manner as a driver card.
 (346) The workshop card shall be able to store at least 4 such records.
 4.5.4.2.10  (347) The workshop card shall be able to store daily works period start and/or end data records in the same manner as a driver card.
 (348) The workshop card shall be able to hold at least 3 pairs of such records.
 4.5.4.2.11  (349) The workshop card shall be able to store a card session data record in the same manner as a driver card.
 4.5.4.2.12  (350) The workshop card shall be able to store a control activity data record in the same manner as a driver card.
 4.5.4.2.13  (351) 

— the date and time of the beginning of the period of use of the vehicle unit (i.e. first card insertion in the vehicle unit for the period),
— the manufacturer of the vehicle unit,
— the vehicle unit type,
— the vehicle unit software version number.
 (352) The workshop card shall be able to store at least 4 such records.
 4.5.4.2.14  (353) 

— the date and time when the accumulated driving time reaches a multiple of three hours,
— the position of the vehicle,
— the GNSS accuracy, date and time when the position was determined,
— the vehicle odometer value.
 (354) The workshop card shall be able to store at least 18 such records.
 4.5.4.2.15  (355) The workshop card shall be able to store data relevant to specific conditions in the same manner as the driver card.
 (356) The workshop card shall be able to store at least 2 such records.
 4.5.5  4.5.5.1  4.5.5.1.1  (357) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.5.1.2  (358) The control card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part A.
 4.5.5.1.3  (359) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date (if any).
 4.5.5.1.4  (360) 

— control body name,
— control body address,
— surname of the holder,
— first name(s) of the holder,
— preferred language.
 4.5.5.1.5  (361) 

— date and time of the control,
— type of the control (displaying and/or printing and/or VU downloading and/or card downloading and/or roadside calibration checking),
— period downloaded (if any),
— VRN and Member State registering authority of the controlled vehicle,
— card number and card issuing Member State of the driver card controlled.
 (362) The control card shall be able to hold at least 230 such records.
 4.5.5.2  4.5.5.2.1  (363) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.5.2.2  (364) The control card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part B.
 4.5.5.2.3  (365) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date (if any).
 4.5.5.2.4  (366) 

— control body name,
— control body address,
— surname of the holder,
— first name(s) of the holder,
— preferred language.
 4.5.5.2.5  (367) 

— date and time of the control,
— type of the control (displaying and/or printing and/or VU downloading and/or card downloading and/or roadside calibration checking)
— period downloaded (if any),
— VRN and Member State registering authority of the controlled vehicle,
— card number and card issuing Member State of the driver card controlled.
 (368) The control card shall be able to hold at least 230 such records.
 4.5.6  4.5.6.1  4.5.6.1.1  (369) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.6.1.2  (370) The company card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part A.
 4.5.6.1.3  (371) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date (if any).
 4.5.6.1.4  (372) 

— company name,
— company address.
 4.5.6.1.5  (373) 

— date and time of the activity,
— type of the activity (VU locking in and/or out, and/or VU downloading and/or card downloading)
— period downloaded (if any),
— VRN and Member State registering authority of vehicle,
— card number and card issuing Member State (in case of card downloading).
 (374) The company card shall be able to hold at least 230 such records.
 4.5.6.2  4.5.6.2.1  (375) 

— tachograph application identification,
— type of tachograph card identification.
 4.5.6.2.2  (376) The company card shall be able to store a number of cryptographic keys and certificates, as specified in Appendix 11 part B.
 4.5.6.2.3  (377) 

— card number,
— issuing Member State, issuing authority name, issue date,
— card beginning of validity date, card expiry date (if any).
 4.5.6.2.4  (378) 

— company name,
— company address.
 4.5.6.2.5  (379) 

— date and time of the activity,
— type of the activity (VU locking in and/or out, and/or VU downloading and/or card downloading)
— period downloaded (if any),
— VRN and Member State registering authority of vehicle,
— card number and card issuing Member State (in case of card downloading).
 (380) The company card shall be able to hold at least 230 such records.

5.  5.1  (381) New recording equipment shall be delivered non-activated to fitters or vehicle manufacturers, with all calibration parameters, as listed in Chapter 3.21, set to appropriate and valid default values. Where no particular value is appropriate, literal parameters shall be set to strings of ‘?’ and numeric parameters shall be set to ‘0’. Delivery of security relevant parts of the recording equipment can be restricted if required during security certification.
 (382) Before its activation, the recording equipment shall give access to the calibration function even if not in calibration mode.
 (383) Before its activation, the recording equipment shall neither record nor store data referred by points 3.12.3, 3.12.9 and 3.12.12 to 3.12.15 inclusive.
 (384) During installation, vehicle manufacturers shall pre-set all known parameters.
 (385) Vehicle manufacturers or fitters shall activate the installed recording equipment at the latest before the vehicle is used in scope of Regulation (EC) No 561/2006.
 (386) The activation of the recording equipment shall be triggered automatically by the first insertion of a valid workshop card in either of its card interface devices.
 (387) Specific pairing operations required between the motion sensor and the vehicle unit, if any, shall take place automatically before or during activation.
 (388) In a similar way, specific coupling operations between the external GNSS facility and the vehicle unit, if any, shall take place automatically before or during activation.
 (389) After its activation, the recording equipment shall fully enforce functions and data access rights.
 (390) After its activation, the recording equipment shall communicate to the remote communication facility the secured data necessary for the purpose of targeted roadside checks.
 (391) The recording and storing functions of the recording equipment shall be fully operational after its activation.
 (392) Installation shall be followed by a calibration. The first calibration may not necessarily include entry of the vehicle registration number (VRN), when it is not known by the approved workshop having to undertake this calibration. In these circumstances, it shall be possible, for the vehicle owner, and at this time only, to enter the VRN using his Company Card prior to using the vehicle in scope of Regulation (EC) No 561/2006 (e.g by using commands through an appropriate menu structure of the vehicle unit's man-machine interface.). Any update or confirmation of this entry shall only be possible using a Workshop Card.
 (393) The installation of an external GNSS facility requires the coupling with the vehicle unit and the subsequent verification of the GNSS position information.
 (394) The recording equipment must be positioned in the vehicle in such a way as to allow the driver to access the necessary functions from his seat.
 5.2  (395) 
After every inspection by an approved fitter or workshop, a new plaque shall be affixed in place of the previous one.
 (396) 

— name, address or trade name of the approved fitter or workshop,
— characteristic coefficient of the vehicle, in the form ‘w = … imp/km’,
— constant of the recording equipment, in the form ‘k = … imp/km’,
— effective circumference of the wheel tyres in the form ‘l = … mm’,
— tyre size,
— the date on which the characteristic coefficient of the vehicle and the effective circumference of the wheel tyres were measured,
— the vehicle identification number,
— the presence (or not) of an external GNSS facility,
— the serial number of the external GNSS facility, if applicable,
— the serial number of the remote communication device, if any,
— the serial number of all the seals in place,
— the part of the vehicle where the adaptor, if any, is installed,
— the part of the vehicle where the motion sensor is installed, if not connected to the gear-box or an adaptor is not being used,
— a description of the colour of the cable between the adaptor and that part of the vehicle providing its incoming impulses,
— the serial number of the embedded motion sensor of the adaptor.
 (397) 
This second, additional plaque, if used, shall be affixed next to or beside the first primary plaque described in Requirement 396, and shall have the same protection level. Furthermore the secondary plaque shall also bear the name, address or trade name of the approved fitter or workshop that carried out the installation, and the date of installation.
 5.3  (398) 

— Any connection which, if disconnected, would cause undetectable alterations to be made or undetectable data loss (this may e.g. apply for the motion sensor fitting on the gearbox, the adaptor for M1/N1 vehicles, the external GNSS connection or the vehicle unit);
— The installation plaque, unless it is attached in such a way that it cannot be removed without the markings thereon being destroyed.
 (398a) The seals mentioned above shall be certified according to the standard EN 16882:2016.
 (399) 

— In case of emergency,
— To install, to adjust or to repair a speed limitation device or any other device contributing to road safety, provided that the recording equipment continues to function reliably and correctly and is resealed by an approved fitter or workshop (in accordance with Chapter 6) immediately after fitting the speed limitation device or any other device contributing to road safety or within seven days in other cases.
 (400) On each occasion that these seals are broken a written statement giving the reasons for such action shall be prepared and made available to the competent authority.
 (401) 
This unique identification number is defined as: MMNNNNNNNN by non-removable marking, with MM as unique manufacturer identification (database registration to be managed by EC) and NNNNNNNN seal alpha-numeric number, unique in the manufacturer domain.
 (402) 
This mark shall not cover the seal identification number.
 (403) Seals manufacturers shall be registered in a dedicated database when they get a seal model certified according to EN 16882:2016 and shall make their identification seals numbers public through a procedure to be established by the European Commission.
 (404) Approved workshops and vehicle manufacturers shall, in the frame of Regulation (EU) No 165/2014, only use seals certified according to EN 16882:2016 from those of the seals manufacturers listed in the database mentioned above.
 (405) Seal manufacturers and their distributors shall maintain full traceability records of the seals sold to be used in the frame of Regulation (EU) No 165/2014 and shall be prepared to produce them to competent national authorities whenever need be.
 (406) Seals unique identification numbers shall be visible on the installation plaque.

6. 
Requirements on the circumstances in which seals may be removed, as referred to in Article 22(5) of Regulation (EU) No 165/2014, are defined in Chapter 5.3 of this annex.
 6.1 
The Member States approve, regularly control and certify the bodies to carry out:


— installations,
— checks,
— inspections,
— repairs.

Workshop cards shall be issued only to fitters and/or workshops approved for the activation and/or the calibration of recording equipment in conformity with this annex and, unless duly justified:


— who are not eligible for a company card;
— and whose other professional activities do not present a potential compromise of the overall security of the system as required in Appendix 10.
 6.2  (407) Every individual device, whether new or repaired, shall be checked in respect of its proper operation and the accuracy of its reading and recordings, within the limits laid down in Chapter 3.2.1, 3.2.2, 3.2.3 and 3.3.
 6.3  (408) When being fitted to a vehicle, the whole installation (including the recording equipment) shall comply with the provisions relating to maximum tolerances laid down in Chapter 3.2.1, 3.2.2, 3.2.3 and 3.3. The whole installation shall be sealed in accordance with Chapter 5.3 and it shall include a calibration.
 6.4  (409) Periodic inspections of the equipment fitted to the vehicles shall take place after any repair of the equipment, or after any alteration of the characteristic coefficient of the vehicle or of the effective circumference of the tyres, or after equipment UTC time is wrong by more than 20 minutes, or when the VRN has changed, and at least once within two years (24 months) of the last inspection.
 (410) 

— that the recording equipment is working properly, including the data storage in tachograph cards function and the communication with remote communication readers,
— that compliance with the provisions of chapter 3.2.1 and 3.2.2 on the maximum tolerances on installation is ensured,
— that compliance with the provisions of chapter 3.2.3 and 3.3 is ensured,
— that the recording equipment carries the type approval mark,
— that the installation plaque, as defined by Requirement 396, and the descriptive plaque, as defined by Requirement 225, are affixed,
— the tyre size and the actual circumference of the tyres,
— that there are no manipulation devices attached to the equipment,
— that seals are correctly placed, in good state, that their identification numbers are valid (referenced seal manufacturer in the EC database) and that their identification numbers correspond to the installation plaque markings (see requirement 401).
 (411) 

a.. make a comparison between the motion sensor identification data of the motion sensor plugged into the gearbox with that of the paired motion sensor registered in the vehicle unit;
b.. check if the information recorded on the installation plaque matches with the information contained within the vehicle unit record;
c.. check if the motion sensor serial number and approval number, if printed on the body of the motion sensor, matches the information stored in the recording equipment data memory;
d.. compare identification data marked on the descriptive plaque of the external GNSS facility, if any, to the ones stored in the vehicle unit data memory;
 (412) Workshops shall keep traces in their inspection reports of any findings concerning broken seals or manipulations devices. These reports shall be kept by workshops for at least 2 years and made available to the Competent Authority whenever requested to do so.
 (413) These inspections shall include a calibration and a preventive replacement of the seals whose fitting is under the responsibility of workshops.
 6.5  (414) 

— vehicle unladen, in normal running order,
— tyre pressures in accordance with the manufacturer's instructions,
— tyre wear, within the limits allowed by national law,
— vehicle movement:
— the vehicle shall advance under its own engine power in a straight line on level ground and at a speed of 50 ± 5 km/h. The measuring distance shall be at least 1 000 m.
— provided that it is of comparable accuracy, alternative methods, such as a suitable test bench, may also be used for the test.
 6.6  (415) Workshops shall be able to download data from the recording equipment to give the data back to the appropriate transport company.
 (416) Approved workshops shall issue to transport companies a certificate of data un-downloadability where the malfunction of the recording equipment prevents previously recorded data to be downloaded, even after repair by this workshop. The workshops will keep a copy of each issued certificate for at least two years.

7. 
The card issuing processes set-up by the Member States shall conform to the following:
 (417) The card number of the first issue of a tachograph card to an applicant shall have a consecutive index (if applicable) and a replacement index and a renewal index set to “0”.
 (418) The card numbers of all non-personal tachograph cards issued to a single control body or a single workshop or a single transport company shall have the same first 13 digits, and shall all have a different consecutive index.
 (419) A tachograph card issued in replacement of an existing tachograph card shall have the same card number than the replaced one except the replacement index which shall be raised by “1” (in the order 0, …, 9, A, …, Z).
 (420) A tachograph card issued in replacement of an existing tachograph card shall have the same card expiry date as the replaced one.
 (421) A tachograph card issued in renewal of an existing tachograph card shall have the same card number as the renewed one except the replacement index which shall be reset to “0” and the renewal index which shall be raised by “1” (in the order 0, …, 9, A, …, Z).
 (422) The exchange of an existing tachograph card, in order to modify administrative data, shall follow the rules of the renewal if within the same Member State, or the rules of a first issue if performed by another Member State.
 (423) The ‘card holder surname’ for non-personal workshop or control cards shall be filled with workshop or control body name or with the fitter or control officer's name would Member States so decide.
 (424) Member States shall exchange data electronically in order to ensure the uniqueness of driver cards that they issue in accordance with Article 31 of Regulation (EU) No 165/2014.

8.  8.1 
For the purpose of this chapter, the words ‘recording equipment’ mean ‘recording equipment or its components’. No type approval is required for the cable(s) linking the motion sensor to the VU, the external GNSS facility to the VU or the external remote communication facility to the VU. The paper, for use by the recording equipment, shall be considered as a component of the recording equipment.

Any manufacturer may ask for type approval of recording equipment component(s) with any other recording equipment component(s), provided each component complies with the requirements of this annex. Alternately, manufacturers may also ask for type approval of recording equipment.

As described in definition (10) in Article 2 of this Regulation, vehicle units have variants in components assembly. Whatever the vehicle unit components assembly, the external antenna and (if applicable) the antenna splitter connected to the GNSS receiver or to the remote communication facility are not part of the vehicle unit type approval.

Nevertheless, manufacturers having obtained type approval for recording equipment shall maintain a publicly available list of compatible antennas and splitters with each type approved vehicle unit, external GNSS facility and external remote communication facility.
 (425) Recording equipment shall be submitted for approval complete with any integrated additional devices.
 (426) Type approval of recording equipment and of tachograph cards shall include security related tests, functional tests and interoperability tests. Positive results to each of these tests are stated by an appropriate certificate.
 (427) 

— a security certificate (if requested by this Annex),
— a functional certificate,
— and an interoperability certificate (if requested by this Annex)

for the recording equipment or the tachograph card, subject of the request for type approval.
 (428) Any modification in software or hardware of the equipment or in the nature of materials used for its manufacture shall, before being used, be notified to the authority which granted type-approval for the equipment. This authority shall confirm to the manufacturer the extension of the type approval, or may require an update or a confirmation of the relevant functional, security and/or interoperability certificates.
 (429) Procedures to upgrade in-situ recording equipment software shall be approved by the authority which granted type approval for the recording equipment. Software upgrade must not alter nor delete any driver activity data stored in the recording equipment. Software may be upgraded only under the responsibility of the equipment manufacturer.
 (430) Type approval of software modifications aimed to upgrade a previously type approved recording equipment may not be refused if such modifications only apply to functions not specified in this Annex. Software upgrade of a recording equipment may exclude the introduction of new character sets, if not technically feasible.
 8.2  (431) The security certificate is delivered in accordance with the provisions of Appendix 10 of this Annex. Recording equipment components to be certified are vehicle unit, motion sensor, external GNSS facility and tachograph cards.
 (432) In the exceptional circumstance that the security certification authorities refuse to certify new equipment on the ground of obsolescence of the security mechanisms, type approval shall continue to be granted only in these specific and exceptional circumstances, and when no alternative solution, compliant with the Regulation, exists.
 (433) In this circumstance the Member State concerned shall, without delay, inform the European Commission, which shall, within twelve calendar months of the grant of the type approval, launch a procedure to ensure that the level of security is restored to its original levels.
 8.3  (434) Each candidate for type approval shall provide the Member State's type approval authority with all the material and documentation that the authority deems necessary.
 (435) Manufacturers shall provide the relevant samples of type approval candidate products and associated documentation required by laboratories appointed to perform functional tests, and within one month of the request being made. Any costs resulting from this request shall be borne by the requesting entity. Laboratories shall treat all commercially sensitive information in confidence.
 (436) A functional certificate shall be delivered to the manufacturer only after all functional tests specified in Appendix 9, at least, have been successfully passed.
 (437) The type approval authority delivers the functional certificate. This certificate shall indicate, in addition to the name of its beneficiary and the identification of the model, a detailed list of the tests performed and the results obtained.
 (438) The functional certificate of any recording equipment component shall also indicate the type approval numbers of the other type approved compatible recording equipment components tested for its certification.
 (439) The functional certificate of any recording equipment component shall also indicate the ISO or CEN standard against which the functional interface has been certified.
 8.4  (440) Interoperability tests are carried out by a single laboratory under the authority and responsibility of the European Commission.
 (441) The laboratory shall register interoperability test requests introduced by manufacturers in the chronological order of their arrival.
 (442) 

— the entire set of material and documents necessary for such interoperability tests,
— the corresponding security certificate,
— the corresponding functional certificate,

The date of the registration of the request shall be notified to the manufacturer.
 (443) No interoperability tests shall be carried out by the laboratory, for recording equipment or tachograph cards that have not been granted a security certificate and a functional certificate, except in the exceptional circumstances described in Requirement 432.
 (444) Any manufacturer requesting interoperability tests shall commit to leave to the laboratory in charge of these tests the entire set of material and documents which he provided to carry out the tests.
 (445) 

— for which type approval is still valid or,
— for which type approval is pending and that have a valid interoperability certificate.
 (446) The interoperability tests shall cover all generations of recording equipment or tachograph cards still in use.
 (447) The interoperability certificate shall be delivered by the laboratory to the manufacturer only after all required interoperability tests have been successfully passed.
 (448) If the interoperability tests are not successful with one or more of the recording equipment or tachograph card(s), the interoperability certificate shall not be delivered, until the requesting manufacturer has realised the necessary modifications and has succeeded the interoperability tests. The laboratory shall identify the cause of the problem with the help of the manufacturers concerned by this interoperability fault and shall attempt to help the requesting manufacturer in finding a technical solution. In the case where the manufacturer has modified its product, it is the manufacturer's responsibility to ascertain from the relevant authorities that the security certificate and the functional certificates are still valid.
 (449) The interoperability certificate is valid for six months. It is revoked at the end of this period if the manufacturer has not received a corresponding type approval certificate. It is forwarded by the manufacturer to the type approval authority of the Member State who has delivered the functional certificate.
 (450) Any element that could be at the origin of an interoperability fault shall not be used for profit or to lead to a dominant position.
 8.5  (451) The type approval authority of the Member State may deliver the type approval certificate as soon as it holds the three required certificates.
 (452) The type approval certificate of any recording equipment component shall also indicate the type approval numbers of the other type approved interoperable recording equipment.
 (453) The type approval certificate shall be copied by the type approval authority to the laboratory in charge of the interoperability tests at the time of deliverance to the manufacturer.
 (454) 

— for which a request for interoperability tests have been registered,
— having received an interoperability certificate (even provisional),
— having received a type approval certificate.
 8.6  (455) Until four months after a first couple of 2nd generation recording equipment and 2nd generation tachograph cards (driver, workshop, control and company cards) have been certified to be interoperable, any interoperability certificate delivered (including the first ones), regarding requests registered during this period, shall be considered provisional.
 (456) If at the end of this period, all products concerned are mutually interoperable, all corresponding interoperability certificates shall become definitive.
 (457) If during this period, interoperability faults are found, the laboratory in charge of interoperability tests shall identify the causes of the problems with the help of all manufacturers involved and shall invite them to realize the necessary modifications.
 (458) If at the end of this period, interoperability problems still remain, the laboratory in charge of interoperability tests, with the collaboration of the manufacturers concerned and with the type approval authorities who delivered the corresponding functional certificates shall find out the causes of the interoperability faults and establish which modifications should be made by each of the manufacturers concerned. The search for technical solutions shall last for a maximum of two months, after which, if no common solution is found, the Commission, after having consulted the laboratory in charge of interoperability tests, shall decide which equipment(s) and cards get a definitive interoperability certificate and state the reasons why.
 (459) Any request for interoperability tests, registered by the laboratory between the end of the four month period after the first provisional interoperability certificate has been delivered and the date of the decision by the Commission referred to in requirement 455, shall be postponed until the initial interoperability problems have been solved. Those requests are then processed in the chronological order of their registration.

Appendix 1 1. 
This appendix specifies data formats, data elements, and data structures for use within the recording equipment and tachograph cards.
 1.1. 
This appendix uses Abstract Syntax Notation One (ASN.1) to define data types. This enables simple and structured data to be defined without implying any specific transfer syntax (encoding rules) which will be application and environment dependent.

ASN.1 type naming conventions are done in accordance with ISO/IEC 8824-1. This implies that:


— where possible, the meaning of the data type is implied through the names being selected,
— where a data type is a composition of other data types, the data type name is still a single sequence of alphabetical characters commencing with a capital letter, however capitals are used within the name to impart the corresponding meaning,
— in general, the data types names are related to the name of the data types from which they are constructed, the equipment in which data is stored and the function related to the data.

If an ASN.1 type is already defined as part of another standard and if it is relevant for usage in the recording equipment, then this ASN.1 type will be defined in this appendix.

To enable several types of encoding rules, some ASN.1 types in this appendix are constrained by value range identifiers. The value range identifiers are defined in paragraph 3 and Appendix 2.
 1.2. 
The following references are used in this Appendix:

ISO 639Code for the representation of names of languages. First Edition: 1988.ISO 3166Codes for the representation of names of countries and their subdivisions — Part 1: Country codes, 2013ISO 3779Road vehicles — Vehicle identification number (VIN) — Content and structure. 2009ISO/IEC 7816-5Identification cards — Integrated circuit cards — Part 5: Registration of application providers.
Second edition: 2004.ISO/IEC 7816-6Identification cards — Integrated circuit cards — Part 6: Interindustry data elements for interchange, 2004 + Technical Corrigendum 1: 2006ISO/IEC 8824-1Information technology — Abstract Syntax Notation One (ASN.1): Specification of basic notation. 2008 + Technical Corrigendum 1: 2012 and Technical Corrigendum 2: 2014.ISO/IEC 8825-2Information technology — ASN.1 encoding rules: Specification of Packed Encoding Rules (PER). 2008.ISO/IEC 8859-1Information technology — 8 bit single-byte coded graphic character sets — Part 1: Latin alphabet No.1. First edition: 1998.ISO/IEC 8859-7Information technology — 8 bit single-byte coded graphic character sets — Part 7: Latin/Greek alphabet. 2003.ISO 16844-3Road vehicles — Tachograph systems — Motion Sensor Interface. 2004 + Technical Corrigendum 1: 2006..TR-03110-3BSI / ANSSI Technical Guideline TR-03110-3, Advanced Security Mechanisms for Machine Readable Travel Documents and eIDAS Token — Part 3 Common Specifications, version 2.20, 3. February 2015
 2. 
For any of the following data types, the default value for an ‘unknown’ or a ‘not applicable’ content will consist in filling the data element with ‘FF’ bytes.

All data types are used for Generation 1 and Generation 2 applications unless otherwise specified.

For card data types used for Generation 1 and Generation 2 applications, the size specified in this Appendix is the one for Generation 2 application. The size for Generation 1 application is supposed to be already known by the reader. The Annex IC requirement numbers related to such data types cover both Generation 1 and Generation 2 applications.
 2.1. 
This data type enables to code, within a two bytes word, a slot status at 00:00 and/or a driver status at 00:00 and/or changes of activity and/or changes of driving status and/or changes of card status for a driver or a co-driver. This data type is related to Annex 1C requirements 105, 266, 291, 320, 321, 343, and 344.

For Data Memory recordings (or slot status):

‘s’BSlot:
 ‘0’B: DRIVER,
 ‘1’B: CO-DRIVER,‘c’BDriving status:
 ‘0’B: SINGLE,
 ‘1’B: CREW,‘p’BDriver (or workshop) card status in the relevant slot:
 ‘0’B: INSERTED, a card is inserted,
 ‘1’B: NOT INSERTED, no card is inserted (or a card is withdrawn),‘aa’BActivity:
 ‘00’B: BREAK/REST,
 ‘01’B: AVAILABILITY,
 ‘10’B: WORK,
 ‘11’B: DRIVING,‘ttttttttttt’BTime of the change: Number of minutes since 00h00 on the given day.

For Driver (or Workshop) card recordings (and driver status):

‘s’BSlot (not relevant when ‘p’=1 except note below):
 ‘0’B: DRIVER,
 ‘1’B: CO-DRIVER,‘c’BDriving status (case ‘p’=0) or
Following activity status (case ‘p’=1):
 ‘0’B: SINGLE,
 ‘0’B: UNKNOWN
 ‘1’B: CREW,
 ‘1’B: KNOWN (=manually entered)‘p’BCard status:
 ‘0’B: INSERTED, the card is inserted in a recording equipment,
 ‘1’B: NOT INSERTED, the card is not inserted (or the card is withdrawn),‘aa’BActivity (not relevant when ‘p’=1 and ‘c’=0 except note below):
 ‘00’B: BREAK/REST,
 ‘01’B: AVAILABILITY,
 ‘10’B: WORK,
 ‘11’B: DRIVING,‘ttttttttttt’BTime of the change: Number of minutes since 00h00 on the given day.

When the card is withdrawn:


— ‘s’ is relevant and indicates the slot from which the card is withdrawn,
— ‘c’ must be set to 0,
— ‘p’ must be set to 1,
— ‘aa’ must code the current activity selected at that time,

As a result of a manual entry, the bits ‘c’ and ‘aa’ of the word (stored in a card) may be overwritten later to reflect the entry.
 2.2. 
An address.

codePage specifies a character set defined in Chapter 4,

address is an address encoded using the specified character set.
 2.3. 
Generation 2:

An AES key with a length of 128, 192 or 256 bits.

Value assignment: not further specified.
 2.4. 
Generation 2:

An AES128 key.

length denotes the length of the AES128 key in octets.

aes128Key is an AES key with a length of 128 bits.

Value assignment:

The length shall have the value 16.
 2.5. 
Generation 2:

An AES192 key.

length denotes the length of the AES192 key in octets.

aes192Key is an AES key with a length of 192 bits.

Value assignment:

The length shall have the value 24.
 2.6. 
Generation 2:

An AES256 key.

length denotes the length of the AES256 key in octets.

aes256Key is an AES key with a length of 256 bits.

Value assignment:

The length shall have the value 32.
 2.7. 
BCDString is applied for Binary Code Decimal (BCD) representation. This data type is used to represent one decimal digit in one semi octet (4 bits). BCDString is based on the ISO/IEC 8824-1 ‘CharacterStringType’.

BCDString uses an ‘hstring’ notation. The leftmost hexadecimal digit shall be the most significant semi octet of the first octet. To produce a multiple of octets, zero trailing semi octets shall be inserted, as needed, from the leftmost semi octet position in the first octet.

Permitted digits are: 0, 1, .. 9.
 2.8. 
Code explaining why a set of calibration parameters was recorded. This data type is related to Annex 1B requirements 097 and 098 and Annex 1C requirements 119.

Value assignment:


 Generation 1:
‘00’Hreserved value,‘01’Hactivation: recording of calibration parameters known, at the moment of the VU activation,‘02’Hfirst installation: first calibration of the VU after its activation,‘03’Hinstallation: first calibration of the VU in the current vehicle,‘04’Hperiodic inspection.
 Generation 2:
In addition to generation 1 the following values are used:
‘05’Hentry of VRN by company,‘06’Htime adjustment without calibration,‘07’H to ‘7F’HRFU,‘80’H to ‘FF’HManufacturer specific.
 2.9. 
Information, stored in a card, related to the driver activities for a particular calendar day. This data type is related to Annex 1C requirements 266, 291, 320 and 343.

activityPreviousRecordLength is the total length in bytes of the previous daily record. The maximum value is given by the length of the OCTET STRING containing these records (see CardActivityLengthRange Appendix 2 paragraph 4). When this record is the oldest daily record, the value of activityPreviousRecordLength must be set to 0.

activityRecordLength is the total length in bytes of this record. The maximum value is given by the length of the OCTET STRING containing these records.

activityRecordDate is the date of the record.

activityDailyPresenceCounter is the daily presence counter for the card this day.

activityDayDistance is the total distance travelled this day.

activityChangeInfo is the set of ActivityChangeInfo data for the driver this day. It may contain at maximum 1440 values (one activity change per minute). This set always includes the activityChangeInfo coding the driver status at 00:00.
 2.10. 
Number of bytes in a driver or a workshop card, available to store driver activity records.

Value assignment: see Appendix 2.
 2.11. 
Type approval number of the card.

Value assignment:

The approval number shall be provided as published on the corresponding European Commission web site, i.e. for example including hyphens if any. The approval number shall be left-aligned.
 2.12. 
Generation 1:

Certificate of the public key of a card.
 2.13. 
Information, stored in a card, related to the identification of the card's Integrated Circuit (IC) (Annex 1C requirement 249). The icSerialNumber together with the icManufacturingReferences identifies the card chip uniquely. The icSerialNumber alone does not uniquely identify the card chip.

icSerialNumber is the IC serial number.

icManufacturingReferences is the IC manufacturer specific identifier.
 2.14. 
A card consecutive index (definition h)).

Value assignment: (see Annex 1C chapter 7)

Order for increase: ‘0, …, 9, A, …, Z, a, …, z’
 2.15. 
Information, stored in a driver or workshop card, related to the last control the driver has been subject to (Annex 1C requirements 274, 299, 327, and 350).

controlType is the type of the control.

controlTime is the date and time of the control.

controlCardNumber is the FullCardNumber of the control officer having performed the control.

controlVehicleRegistration is the VRN and registering Member State of the vehicle in which the control happened.

controlDownloadPeriodBegin and controlDownloadPeriodEnd is the period downloaded, in case of downloading.
 2.16. 
Information about the actual usage of the card (Annex 1C requirement 273, 298, 326, and 349).

sessionOpenTime is the time when the card is inserted for the current usage. This element is set to zero at card removal.

sessionOpenVehicle is the identification of the currently used vehicle, set at card insertion. This element is set to zero at card removal.
 2.17. 
Information, stored in a driver or a workshop card, related to the activities of the driver (Annex 1C requirements 267, 268, 292, 293, 321 and 344).

activityPointerOldestDayRecord is the specification of the begin of the storage place (number of bytes from the beginning of the string) of the oldest complete day record in the activityDailyRecords string. The maximum value is given by the length of the string.

activityPointerNewestRecord is the specification of the begin of the storage place (number of bytes from the beginning of the string) of the most recent day record in the activityDailyRecords string. The maximum value is given by the length of the string.

activityDailyRecords is the space available to store the driver activity data (data structure: CardActivityDailyRecord) for each calendar day where the card has been used.

Value assignment: this octet string is cyclically filled with records of CardActivityDailyRecord. At the first use storing is started at the first byte of the string. All new records are appended at the end of the previous one. When the string is full, storing continues at the first byte of the string independently of a break being inside a data element. Before placing new activity data in the string (enlarging current activityDailyRecord, or placing a new activityDailyRecord) that replaces older activity data, activityPointerOldestDayRecord must be updated to reflect the new location of the oldest complete day record, and activityPreviousRecordLength of this (new) oldest complete day record must be reset to 0.
 2.18. 
Information, stored in a driver card, related to the card holder driver licence data (Annex 1C requirement 259 and 284).

drivingLicenceIssuingAuthority is the authority responsible for issuing the driving licence.

drivingLicenceIssuingNation is the nationality of the authority that issued the driving licence.

drivingLicenceNumber is the number of the driving licence.
 2.19. 
Generation 1:

Information, stored in a driver or workshop card, related to the events associated with the card holder (Annex IC requirements 260 and 318).




                                    CardEventData
                                  is a sequence, ordered by ascending value of EventFaultType, of cardEventRecords (except security breach attempts related records which are gathered in the last set of the sequence).


                                    cardEventRecords
                                  is a set of event records of a given event type (or category for security breach attempts events).

Generation 2:

Information, stored in a driver or workshop card, related to the events associated with the card holder (Annex IC requirements 285 and 341).




                                    CardEventData
                                  is a sequence, ordered by ascending value of EventFaultType, of cardEventRecords (except security breach attempts related records which are gathered in the last set of the sequence).


                                    cardEventRecords
                                  is a set of event records of a given event type (or category for security breach attempts events).
 2.20. 
Information, stored in a driver or a workshop card, related to an event associated to the card holder (Annex 1C requirements 261, 286, 318 and 341).

eventType is the type of the event.

eventBeginTime is the date and time of beginning of event.

eventEndTime is the date and time of end of event.

eventVehicleRegistration is the VRN and registering Member State of vehicle in which the event happened.
 2.21. 
Information, stored in a driver or a workshop card, related to the faults associated to the card holder (Annex 1C requirements 263, 288, 318, and 341).

CardFaultData is a sequence of Recording Equipment faults set of records followed by card faults set of records.

cardFaultRecords is a set of fault records of a given fault category (Recording Equipment or card).
 2.22. 
Information, stored in a driver or a workshop card, related to a fault associated to the card holder (Annex 1C requirement 264, 289, 318, and 341).

faultType is the type of the fault.

faultBeginTime is the date and time of beginning of fault.

faultEndTime is the date and time of end of fault.

faultVehicleRegistration is the VRN and registering Member State of vehicle in which the fault happened.
 2.23. 
Information, stored in a card, related to the identification of the integrated circuit (IC) card (Annex 1C requirement 248).

clockStop is the Clockstop mode as defined in appendix 2.

cardExtendedSerialNumber is the IC card unique serial number as further specified by the ExtendedSerialNumber data type.

cardApprovalNumber is the type approval number of the card.

cardPersonaliserID is the card personaliser ID encoded as ManufacturerCode.

embedderIcAssemblerId provides information about the embedder/IC assembler.

icIdentifier is the Identifier of the IC on the card and its IC manufacturer as defined in ISO/IEC 7816-6.
 2.24. 
Information, stored in a card, related to the identification of the card (Annex 1C requirements 255, 280, 310, 333, 359, 365, 371, and 377).

cardIssuingMemberState is the code of the Member State issuing the card.

cardNumber is the card number of the card.

cardIssuingAuthorityName is the name of the authority having issued the Card.

cardIssueDate is the issue date of the Card to the current holder.

cardValidityBegin is the first date of validity of the card.

cardExpiryDate is the date when the validity of the card ends.
 2.25. 
Generation 2:

Certificate of the card public key for mutual authentication with a VU. The structure of this certificate is specified in Appendix 11.
 2.26. 
A card number as defined by definition g).

driverIdentification is the unique identification of a driver in a Member State.

ownerIdentification is the unique identification of a company or a workshop or a control body within a member state.

cardConsecutiveIndex is the card consecutive index.

cardReplacementIndex is the card replacement index.

cardRenewalIndex is the card renewal index.

The first sequence of the choice is suitable to code a driver card number, the second sequence of the choice is suitable to code workshop, control, and company card numbers.
 2.27. 
Information, stored in a driver or a workshop card, related to the places where daily work periods begin and/or end (Annex 1C requirements 272, 297, 325, and 348).

placePointerNewestRecord is the index of the last updated place record.

Value assignment: Number corresponding to the numerator of the place record, beginning with ‘0’ for the first occurrence of the place records in the structure.

placeRecords is the set of records containing the information related to the places entered.
 2.28. 
Generation 1:

The private key of a card.
 2.29. 
The public key of a card.
 2.30. 
A card renewal index (definition i)).




                                    Value assignment
                                 : (see this Annex chapter 7).

‘0’First issue.

Order for increase: ‘0, …, 9, A, …, Z’
 2.31. 
A card replacement index (definition j)).

Value assignment: (see this Annex chapter VII).

‘0’Original card.

Order for increase: ‘0, …, 9, A, …, Z’
 2.32. 
Generation 2:

Certificate of the card public key for signature. The structure of this certificate is specified in Appendix 11.
 2.33. 
Code to distinguish between the two slots of a Vehicle Unit.

Value assignment: not further specified.
 2.34. 
Code indicating the type of cards inserted in the two slots of the vehicle unit.

Value assignment — Octet Aligned: ‘ccccdddd’B

‘cccc’BIdentification of the type of card inserted in the co-driver slot,‘dddd’BIdentification of the type of card inserted in the driver slot,

with the following identification codes:

‘0000’Bno card is inserted,‘0001’Ba driver card is inserted,‘0010’Ba workshop card is inserted,‘0011’Ba control card is inserted,‘0100’Ba company card is inserted.
 2.35. 
Generation 2:

The CardSlotsStatus plus metadata as used in the download protocol.

recordType denotes the type of the record (CardSlotsStatus). Value Assignment: See RecordType

recordSize is the size of the CardSlotsStatus in bytes.

noOfRecords is the number of records in the set records.

records is the set of CardSlotsStatus records.
 2.36. 
Code indicating the version of the implemented structure in a tachograph card.

Value assignment: ‘aabb’H:

‘aa’HIndex for changes of the structure.
 ‘00’H for Generation 1 applications
 ‘01’H for Generation 2 applications‘bb’HIndex for changes concerning the use of the data elements defined for the structure given by the high byte.
 ‘00’H for this version of Generation 1 applications
 ‘00’H for this version of Generation 2 applications
 2.37. 
Information, stored in a driver or workshop card, related to a period of use of a vehicle during a calendar day (Annex 1C requirements 269, 294, 322, and 345).


 Generation 1:

vehicleOdometerBegin is the vehicle odometer value at the beginning of the period of use of the vehicle.
vehicleOdometerEnd is the vehicle odometer value at the end of the period of use of the vehicle.
vehicleFirstUse is the date and time of the beginning of the period of use of the vehicle.
vehicleLastUse is the date and time of the end of the period of use of the vehicle.
vehicleRegistration is the VRN and the registering Member State of the vehicle.
vuDataBlockCounter is the value of the VuDataBlockCounter at last extraction of the period of use of the vehicle.
 Generation 2:

In addition to generation 1 the following data element is used:
VehicleIdentificationNumber is the vehicle identification number referring to the vehicle as a whole.
 2.38. 
Information, stored in a driver or workshop card, related to the vehicles used by the card holder (Annex 1C requirements 270, 295, 323, and 346).

vehiclePointerNewestRecord is the index of the last updated vehicle record.

Value assignment: Number corresponding to the numerator of the vehicle record, beginning with ‘0’ for the first occurrence of the vehicle records in the structure.

cardVehicleRecords is the set of records containing information on vehicles used.
 2.39. 
Generation 2:

Information, stored in a driver or workshop card, related to a vehicle unit that was used (Annex 1C requirement 303 and 351).

timeStamp is the beginning of the period of use of the vehicle unit (i.e. first card insertion in the vehicle unit for the period).

manufacturerCode identifies the manufacturer of the Vehicle Unit.

deviceID identifies the Vehicle Unit type of a manufacturer. The value is manufacturer specific.

vuSoftwareVersion is the software version number of the Vehicle Unit.
 2.40. 
Generation 2:

Information, stored in a driver or workshop card, related to the vehicle units used by the card holder (Annex 1C requirement 306 and 352).

vehicleUnitPointerNewestRecord is the index of the last updated vehicle unit record.

Value assignment: Number corresponding to the numerator of the vehicle unit record, beginning with ‘0’ for the first occurrence of the vehicle unit records in the structure.

cardVehicleUnitRecords is the set of records containing information on vehicle units used.
 2.41. 
The certificate of a public key issued by a Certification Authority.


 Generation 1:

Value assignment: digital signature with partial recovery of a CertificateContent according to Appendix 11 common security mechanisms: Signature (128 bytes) || Public Key remainder (58 bytes) || Certification Authority Reference (8 bytes).
 Generation 2:

Value assignment: See Appendix 11
 2.42. 
Generation 1:

The (clear) content of the certificate of a public key according to Appendix 11 common security mechanisms.

certificateProfileIdentifier is the version of the corresponding certificate.

Value assignment: ‘01h’ for this version.

certificationAuthorityReference identifies the Certification Authority issuing the certificate. It also references the Public Key of this Certification Authority.

certificateHolderAuthorisation identifies the rights of the certificate holder.

certificateEndOfValidity is the date when the certificate expires administratively.

certificateHolderReference identifies the certificate holder. It also references his Public Key.

publicKey is the public key that is certified by this certificate.
 2.43. 
Identification of the rights of a certificate holder.


 Generation 1:
 tachographApplicationID is the application identifier for the tachograph application.
Value assignment: ‘FFh’‘54h’‘41h’‘43h’‘48h’‘4Fh’. This AID is a proprietary non registered application identifier in accordance with ISO/IEC 7816-5.
 equipmentType is the identification of the type of equipment to which the certificate is intended.
Value assignment: in accordance with EquipmentType data type. 0 if certificate is the one of a Member State.
 Generation 2:
 tachographApplicationID denotes the 6 most significant bytes of the generation 2 tachograph card application identifier (AID). The AID for the tachograph card application is specified in chapter 6.2.
Value assignment:‘FF 53 4D 52 44 54’.
 equipmentType is the identification of the type of equipment as specified for generation 2 to which the certificate is intended.
Value assignment: in accordance with EquipmentType data type.
 2.44. 
Unique identification of a certificate request. It can also be used as a Vehicle Unit Public Key Identifier if the serial number of the vehicle Unit to which the key is intended is not known at certificate generation time.

requestSerialNumber is a serial number for the certificate request, unique for the manufacturer and the month below.

requestMonthYear is the identification of the month and the year of the certificate request.

Value assignment: BCD coding of Month (two digits) and Year (two last digits).

crIdentifier: is an identifier to distinguish a certificate request from an extended serial number.

Value assignment: ‘FFh’.

manufacturerCode: is the numerical code of the manufacturer requesting the certificate.
 2.45. 
Identifier of the Public Key of a Certification Authority (a Member State or the European Certification Authority).

nationNumeric is the numerical nation code of the Certification Authority.

nationAlpha is the alphanumerical nation code of the Certification Authority.

keySerialNumber is a serial number to distinguish the different keys of the Certification Authority in the case keys are changed.

additionalInfo is a two byte field for additional coding (Certification Authority specific).

caIdentifier is an identifier to distinguish a Certification Authority Key Identifier from other Key Identifiers.

Value assignment: ‘01h’.
 2.46. 
Information, stored in a company card, related to activities performed with the card (Annex 1C requirement 373 and 379).

companyPointerNewestRecord is the index of the last updated companyActivityRecord.

Value assignment: Number corresponding to the numerator of the company activity record, beginning with ‘0’ for the first occurrence of the company activity record in the structure.

companyActivityRecords is the set of all company activity records.

companyActivityRecord is the sequence of information related to one company activity.

companyActivityType is the type of the company activity.

companyActivityTime is the date and time of the company activity.

cardNumberInformation is the card number and the card issuing Member State of the card downloaded, if any.

vehicleRegistrationInformation is the VRN and registering Member State of the vehicle downloaded or locked in or out.

downloadPeriodBegin and downloadPeriodEnd is the period downloaded from the VU, if any.
 2.47. 
Code indicating an activity carried out by a company using its company card.
 2.48. 
Information, stored in a company card related to the identification of the application of the card (Annex 1C requirement 369 and 375).

typeOfTachographCardId is specifying the implemented type of card.

cardStructureVersion is specifying the the version of the structure that is implemented in the card.

noOfCompanyActivityRecords is the number of company activity records the card can store.
 2.49. 
Information, stored in a company card, related to the cardholder identification (Annex 1C requirement 372 and 378).

companyName is the name of the holder company.

companyAddress is the address of the holder company.

cardHolderPreferredLanguage is the preferred language of the card holder.
 2.50. 
Information, stored in a control card related to the identification of the application of the card (Annex 1C requirement 357 and 363).

typeOfTachographCardId is specifying the implemented type of card.

cardStructureVersion is specifying the version of the structure that is implemented in the card.

noOfControlActivityRecords is the number of control activity records the card can store.
 2.51. 
Information, stored in a control card, related to control activity performed with the card (Annex 1C requirement 361 and 367).

controlPointerNewestRecord is the index of the last updated control activity record.

Value assignment: Number corresponding to the numerator of the control activity record, beginning with ‘0’ for the first occurrence of the control activity record in the structure.

controlActivityRecords is the set of all control activity records.

controlActivityRecord is the sequence of information related to one control.

controlType is the type of the control.

controlTime is the date and time of the control.

controlledCardNumber is the card number and the card issuing Member State of the card controlled.

controlledVehicleRegistration is the VRN and registering Member State of the vehicle in which the control happened.

controlDownloadPeriodBegin and controlDownloadPeriodEnd is the period eventually downloaded.
 2.52. 
Information, stored in a control card, related to the identification of the cardholder (Annex 1C requirement 360 and 366).

controlBodyName is the name of the control body of the card holder.

controlBodyAddress is the address of the control body of the card holder.

cardHolderName is the name and first name(s) of the holder of the Control Card.

cardHolderPreferredLanguage is the preferred language of the card holder.
 2.53. 
Code indicating the activities carried out during a control. This data type is related to Annex 1C requirements 126, 274, 299, 327, and 350.


 Generation 1:
Value assignment — Octet aligned: ‘cvpdxxxx’B (8 bits)
‘c’Bcard downloading:
 ‘0’B: card not downloaded during this control activity,
 ‘1’B: card downloaded during this control activity‘v’BVU downloading:
 ‘0’B: VU not downloaded during this control activity,
 ‘1’B: VU downloaded during this control activity‘p’Bprinting:
 ‘0’B: no printing done during this control activity,
 ‘1’B: printing done during this control activity‘d’Bdisplay:
 ‘0’B: no display used during this control activity,
 ‘1’B: display used during this control activity‘xxxx’BNot used.
 Generation 2:
Value assignment — Octet aligned: ‘cvpdexxx’B (8 bits)
‘c’Bcard downloading:
 ‘0’B: card not downloaded during this control activity,
 ‘1’B: card downloaded during this control activity‘v’BVU downloading:
 ‘0’B: VU not downloaded during this control activity,
 ‘1’B: VU downloaded during this control activity‘p’Bprinting:
 ‘0’B: no printing done during this control activity,
 ‘1’B: printing done during this control activity‘d’Bdisplay:
 ‘0’B: no display used during this control activity,
 ‘1’B: display used during this control activity‘e’Broadside calibration checking:
 ‘0’B: calibration parameters not checked during this control activity,
 ‘1’B: calibration parameters checked during this control activity‘xxx’BRFU.
 2.54. 
The current date and time of the recording equipment.

Value assignment: not further specified.
 2.55. 
Generation 2:

The current date and time plus metadata as used in the download protocol.

recordType denotes the type of the record (CurrentDateTime). Value Assignment: See RecordType

recordSize is the size of the CurrentDateTime in bytes.

noOfRecords is the number of records in the set records.

records is a set of current date and time records.
 2.56. 
Counter, stored in a driver or workshop card, increased by one for each calendar day the card has been inserted in a VU. This data type is related to Annex 1C requirements 266, 299, 320, and 343.

Value assignment: Consecutive Number with maximum value = 9 999, starting again with 0. At the time of first issuing of the card the number is set to 0.
 2.57. 
Date expressed in a readily printable numeric format.

Value assignment:

yyyyYearmmMonthddDay‘00000000’Hdenotes explicitly no date.
 2.58. 
Generation 2:

The date and time of the download.

Value assignment: not further specified.
 2.59. 
Generation 2:

The date and time of the download plus metadata as used in the download protocol.

recordType denotes the type of the record (DateOfDayDownloaded). Value Assignment: See RecordType

recordSize is the size of the CurrentDateTime in bytes.

noOfRecords is the number of records in the set records.

records is the set of date and time of the download records.
 2.60. 
A distance travelled (result of the calculation of the difference between two vehicle's odometer values in kilometers).

Value assignment: Unsigned binary. Value in km in the operational range 0 to 9 999 km.
 2.61. 
Information, stored in a driver card related to the identification of the application of the card (Annex 1C requirement 253 and 278).


 Generation 1:

typeOfTachographCardId is specifying the implemented type of card.
cardStructureVersion is specifying the the version of the structure that is implemented in the card.
noOfEventsPerType is the number of events per type of event the card can record.
noOfFaultsPerType is the number of faults per type of fault the card can record.
activityStructureLength indicates the number of bytes available for storing activity records.
noOfCardVehicleRecords is the number of vehicle records the card can contain.
noOfCardPlaceRecords is the number of places the card can record.
 Generation 2:

In addition to generation 1 the following data elements are used:

                                             noOfGNSSADRecords
                                           is the number of GNSS accumulated driving records the card can store.

                                             noOfSpecificConditionRecords
                                           is the number of specific condition records the card can store.

                                             noOfCardVehicleUnitRecords
                                           is the number of vehicle units used records the card can store.
 2.62. 
Information, stored in a driver card, related to the identification of the cardholder (Annex 1C requirement 256 and 281).

cardHolderName is the name and first name(s) of the holder of the Driver Card.

cardHolderBirthDate is the date of birth of the holder of the Driver Card.

cardHolderPreferredLanguage is the preferred language of the card holder.
 2.63.  2.64. 
Generation 2:

Certificate of the external GNSS facility public key for mutual authentication with a VU. The structure of this certificate is specified in Appendix 11.
 2.65. 
Provides information about the IC embedder.

countryCode is the 2 letter country code of the module embedder according to ISO 3166.

moduleEmbedder identifies the module embedder.

manufacturerInformation for manufacturer internal usage.
 2.66. 
Code to distinguish between begin and end for an entry of a daily work period place and condition of the entry.


 Generation 1

Value assignment: according to ISO/IEC8824-1.
 Generation 2

Value assignment: according to ISO/IEC8824-1.
 2.67. 
Code to distinguish different types of equipment for the tachograph application.


 Generation 1:

Value assignment: According to ISO/IEC8824-1.
Value 0 is reserved for the purpose of designating a Member State or Europe in the CHA field of certificates.
 Generation 2:
The same values as in generation 1 are used with the following additions:
 
                                             Note 1:
                                           The generation 2 values for the Plaque, Adapter and the External GNSS connection as well as the generation 1 values for the Vehicle Unit and Motion Sensor may be used in SealRecord, i.e. if applicable.
 
                                             Note 2:
                                           In the CardHolderAuthorisation (CHA) field of a generation 2 certificate, the values (1), (2), and (6) are to be interpreted as indicating a certificate for Mutual Authentication for the respective equipment type. For indicating the respective certificate for creating a digital signature, the values (17), (18) or (19) must be used.

 2.68. 
Generation 1:

The European public key.
 2.69. 
Code explaining why an event or a fault has been recorded.

Value assignment:


 one of the 10 most recent (or last) events or faultsthe longest event for one of the last 10 days of occurrenceone of the 5 longest events over the last 365 daysthe last event for one of the last 10 days of occurrencethe most serious event for one of the last 10 days of occurrenceone of the 5 most serious events over the last 365 daysthe first event or fault having occurred after the last calibrationan active/on-going event or faultRFUmanufacturer specific
 2.70. 
Code qualifying an event or a fault.

Value assignment:


 Generation 1:
 General events,No further details,Insertion of a non valid card,Card conflict,Time overlap,Driving without an appropriate card,Card insertion while driving,Last card session not correctly closed,Over speeding,Power supply interruption,Motion data error,Vehicle Motion Conflict,RFU,
 Vehicle unit related security breach attempt events,No further details,Motion sensor authentication failure,Tachograph card authentication failure,Unauthorised change of motion sensor,Card data input integrity errorStored user data integrity error,Internal data transfer error,Unauthorised case opening,Hardware sabotage,RFU,
 Sensor related security breach attempt events,No further details,Authentication failure,Stored data integrity error,Internal data transfer error,Unauthorised case opening,Hardware sabotage,RFU,
 Recording equipment faults,No further details,VU internal fault,Printer fault,Display fault,Downloading fault,Sensor fault,RFU,
 Card faults,No further details,RFU,
 RFU,
 Manufacturer specific.
 Generation 2:
 General events,No further details,Insertion of a non valid card,Card conflict,Time overlap,Driving without an appropriate card,Card insertion while driving,Last card session not correctly closed,Over speeding,Power supply interruption,Motion data error,Vehicle Motion Conflict,Time conflict (GNSS versus VU internal clock),Communication error with the remote communication facility,Absence of position information from GNSS receiver,Communication error with the external GNSS facility,RFU,
 Vehicle unit related security breach attempt events,No further details,Motion sensor authentication failure,Tachograph card authentication failure,Unauthorised change of motion sensor,Card data input integrity errorStored user data integrity error,Internal data transfer error,Unauthorised case opening,Hardware sabotage,Tamper detection of GNSS,External GNSS facility authentication failure,External GNSS facility certificate expired,RFU,
 Sensor related security breach attempt events,No further details,Authentication failure,Stored data integrity error,Internal data transfer error,Unauthorised case opening,Hardware sabotage,RFU,
 Recording equipment faults,No further details,VU internal fault,Printer fault,Display fault,Downloading fault,Sensor fault,Internal GNSS receiver,External GNSS facility,Remote communication facility,ITS interface,RFU,
 Card faults,No further details,RFU,
 
                                                   RFU,
                                                
 
                                                   Manufacturer specific.
 2.71. 
Generation 2:

The extended seal identifier uniquely identifies a seal (Annex IC requirement 401).




                                    manufacturerCode
                                  is a code of the manufacturer of the seal.


                                    sealIdentifier
                                  is an identifier for the seal which is unique for the manufacturer.
 2.72. 
Unique identification of an equipment. It can also be used as an equipment Public Key Identifier.


 Generation 1:

serialNumber is a serial number for the equipment, unique for the manufacturer, the equipment's type and the month and year below.
monthYear is the identification of the month and the year of manufacturing (or of serial number assignment).
Value assignment: BCD coding of Month (two digits) and Year (two last digits).
type is an identifier of the type of equipment.
Value assignment: manufacturer specific, with ‘FFh’ reserved value.
manufacturerCode: is the numerical code identifying a manufacturer of type approved equipment.
 Generation 2:

serialNumber see Generation 1
monthYear see Generation 1
type indicates the type of equipment
manufacturerCode: see Generation 1.
 2.73. 
Code fully identifying a tachograph card.

cardType is the type of the tachograph card.

cardIssuingMemberState is the code of the Member State having issued the card.

cardNumber is the card number.
 2.74. 
Generation 2:

Code fully identifying a tachograph card and its generation.

fullcardNumber identifies the tachograph card.

generation indicates the generation of the tachograph card used.
 2.75. 
Generation 2:

Indicates the generation of tachograph used.

Value assignment:

‘00’HRFU‘01’HGeneration 1‘02’HGeneration 2‘03’H .. ‘FF’HRFU
 2.76. 
Generation 2:

The geo-coordinates are encoded as integers. These integers are multiples of the ±DDMM.M encoding for the latitude and ±DDDMM.M for the longitude. Here ±DD respectively ±DDD denotes the degrees and MM.M the minutes.

latitude is encoded as a multiple (factor 10) of the ±DDMM.M representation.

longitude is encoded as a multiple (factor 10) of the ±DDDMM.M representation.
 2.77. 
Generation 2:

The accuracy of the GNSS position data (definition eee)). This accuracy is encoded as integer and is a multiple (factor 10) of the X.Y value provided by the GSA NMEA sentence.
 2.78. 
Generation 2:

Information, stored in a driver or workshop card, related to the GNSS position of the vehicle if the accumulated driving time reaches a multiple of three hours (Annex IC requirement 306 and 354).




                                    gnssADPointerNewestRecord
                                  is the index of the last updated GNSS accumulated driving record.


                                    Value assignment
                                  is the number corresponding to the numerator of the GNSS accumulated driving record, beginning with '0' for the first occurrence of the GNSS accumulated driving record in the structure.


                                    gnssAccumulatedDrivingRecords
                                  is the set of records containing the date and time the accumulated driving reaches a multiple of three hours and information on the position of the vehicle.
 2.79. 
Generation 2:

Information, stored in a driver or workshop card, related to the GNSS position of the vehicle if the accumulated driving time reaches a multiple of three hours (Annex IC requirement 305 and 353)




                                    timeStamp
                                  is the date and time when the accumulated driving time reaches a multiple of three hours.


                                    gnssPlaceRecord
                                  contains information related to the position of the vehicle.


                                    vehicleOdometerValue
                                  is the odometer value when the accumulated driving time reaches a multiple of three hours.
 2.80. 
Generation 2:

Information related to the GNSS position of the vehicle (Annex 1C requirements 108, 109, 110, 296, 305, 347, and 353).

timeStamp is the date and time when the GNSS position of the vehicle was determined.

gnssAccuracy is the accuracy of the GNSS position data.

geoCoordinates is the recorded location using GNSS.
 2.81. 
Odometer value of the vehicle: Accumulated distance travelled by the vehicle during its operation.

Value assignment: Unsigned binary. Value in 1/200 km in the operating range 0 to 21 055 406 km.
 2.82. 
A distance travelled during all or part of a journey.

Value assignment: Unsigned binary. Value in 1/200 km in the operating range 0 to 21 055 406 km.
 2.83. 
The surname and first name(s) of a card holder.

holderSurname is the surname (family name) of the holder. This surname does not include titles.

Value assignment: When a card is not personal, holderSurname contains the same information as companyName or workshopName or controlBodyName.

holderFirstNames is the first name(s) and initials of the holder.
 2.84. 
Generation 2:

Information if the GNSS receiver is internal or external to the vehicle unit. True means that the GNSS receiver is internal to the VU. False means that the GNSS receiver is external.
 2.85. 
Constant of the recording equipment (definition m)).

Value assignment: Pulses per kilometer in the operating range 0 to 64 255 pulses/km.
 2.86. 
A unique identifier of a Public Key used to reference and select the key. It also identifies the holder of the key.



The first choice is suitable to reference the public key of a Vehicle Unit, of a tachograph card or of an external GNSS facility.

The second choice is suitable to reference the public key of a Vehicle Unit (in cases where the serial number of the Vehicle Unit cannot be known at certificate generation time).

The third choice is suitable to reference the public key of a Member State.
 2.87. 
Generation 2:

AES key and its associated key version used for VU — Motion Sensor pairing. For details see Appendix 11.

kMWCKey is the length of the AES key concatenated with the key which is used for VU — Motion Sensor pairing.

keyVersion denotes the key version of the AES key.
 2.88. 
Code identifying a language.

Value assignment: Two-letter lower-case coding according to ISO 639.
 2.89. 
Date and time, stored on a driver card, of last card download (for other purposes than control) Annex 1C requirement 257 and 282. This date is updateable by a VU or any card reader.

Value assignment: not further specified.
 2.90. 
Generation 2:

The link certificate between European Root CA key pairs.
 2.91. 
Effective circumference of the wheel tyres (definition u)).

Value assignment: Unsigned binary, value in 1/8 mm in the operating range 0 to 8 031 mm.
 2.92. 
Generation 2:

A cryptographic check sum of 8, 12 or 16 bytes length corresponding to the cipher suites specified in Appendix 11.


 2.93. 
Code identifying whether a cardholder has manually entered driver activities at card insertion or not (Annex 1B requirement 081 and Annex 1C requirement 102).

Value assignment: not further specified.
 2.94. 
Code identifying a manufacturer of type approved equipment.

The laboratory competent for interoperability tests maintains and publishes the list of manufacturer codes on its web site (Annex 1C requirement 454).

ManufacturerCodes are provisionally assigned to developers of tachograph equipment on application to the laboratory competent for interoperability tests.
 2.95. 
Generation 2:

Manufacturer specific error codes simplify the error analysis and maintenance of vehicle units.

manufacturerCode identifies the manufacturer of the Vehicle Unit.

manufacturerSpecificErrorCode is an error code specific to the manufacturer.
 2.96. 
The certificate of the public key of a member state issued by the European certification authority.
 2.97. 
Generation 2:

The member state certificate plus metadata as used in the download protocol.

recordType denotes the type of the record (MemberStateCertificate). Value Assignment: See RecordType

recordSize is the size of the MemberStateCertificate in bytes.

noOfRecords is the number of records in the set records. The value shall be set to 1 as the certficates may have different lengths.

records is the set of member state certificates.
 2.98. 
Generation 1:

The public key of a Member State.
 2.99. 
A name.

codePage specifies a character set defined in Chapter 4,

name is a name encoded using the specified character set.
 2.100. 
Alphabetic reference to a country shall be in accordance with the distinguishing signs used on vehicles in international traffic (United Nations Vienna Convention on Road Traffic, 1968).

The Nation Alpha and Numeric codes shall be held on a list maintained on the website of the laboratory appointed to carry out interoperability testing, as set out in Annex 1C requirement 440.
 2.101. 
Numerical reference to a country.

Value assignment: see data type 2.100 (NationAlpha).

Any amendment or updating of the Nation Alpha or Numeric specification described in the above paragraph shall only be made out after the appointed laboratory has obtained the views of type approved digital and smart tachograph vehicle unit manufacturers.
 2.102. 
Number of calibration records, a workshop card can store.


 Generation 1:

Value assignment: see Appendix 2.
 Generation 2:

Value assignment: see Appendix 2.
 2.103. 
Counter indicating the number of calibrations performed with a workshop card since its last download (Annex 1C requirement 317 and 340).

Value assignment: Not specified further.
 2.104. 
Number of place records a driver or workshop card can store.


 Generation 1:

Value assignment: see Appendix 2.
 Generation 2:

Value assignment: see Appendix 2.
 2.105. 
Number of vehicles used records a driver or workshop card can store.

Value assignment: see Appendix 2.
 2.106. 
Generation 2:

Number of vehicle units used records a driver or workshop card can store.

Value assignment: see Appendix 2.
 2.107. 
Number of company activity records, a company card can store.

Value assignment: see Appendix 2.
 2.108. 
Number of control activity records, a control card can store.

Value assignment: see Appendix 2.
 2.109. 
Number of events per type of event a card can store.

Value assignment: see Appendix 2.
 2.110. 
Number of faults per type of fault a card can store.

Value assignment: see Appendix 2.
 2.111. 
Generation 2:

Number of GNSS accumulated driving records a card can store.




                                    Value assignment:
                                  see Appendix 2.
 2.112. 
Generation 2:

Number of specific condition records a card can store.

Value assignment: see Appendix 2.
 2.113. 
Odometer value of the vehicle in a short form.

Value assignment: Unsigned binary. Value in km in the operating range 0 to 9 999 999 km.
 2.114. 
The vehicle's odometer value at midnight on a given day (Annex 1B requirement 090 and Annex 1C requirement 113).

Value assignment: not further specified.
 2.115. 
Generation 2:

The OdometerValueMidnight plus metadata used in the download protocol.

recordType denotes the type of the record (OdometerValueMidnight). Value Assignment: See RecordType

recordSize is the size of the OdometerValueMidnight in bytes.

noOfRecords is the number of records in the set records.

records is the set of OdometerValueMidnight records.
 2.116. 
Number of over speeding events since the last over speeding control.

Value assignment: 0 means that no over speeding event has occurred since the last over speeding control, 1 means that one over speeding event has occurred since the last over speeding control …255 means that 255 or more over speeding events have occurred since the last over speeding control.
 2.117. 
Information related to a place where a daily work period begins or ends (Annex 1C requirements 108, 271, 296, 324, and 347).


 Generation 1:

entryTime is a date and time related to the entry.
entryTypeDailyWorkPeriod is the type of entry.
dailyWorkPeriodCountry is the country entered.
dailyWorkPeriodRegion is the region entered.
vehicleOdometerValue is the odometer value at the time of place entry.
 Generation 2:

In addition to Generation 1 the following component is used:
entryGNSSPlaceRecord is the recorded location and time.
 2.118. 
Information related to the vehicle previously used by a driver when inserting his card in a vehicle unit (Annex 1B requirement 081 and Annex 1C requirement 102).


 Generation 1:

vehicleRegistrationIdentification is the VRN and the registering Member State of the vehicle.
cardWithdrawalTime is the card withdrawal date and time.
 Generation 2:

In addition to generation 1 the following data element is used:
vuGeneration identifies the generation of the vehicle unit.
 2.119. 
Generation 1:

A public RSA key.

rsaKeyModulus is the Modulus of the key pair.

rsaKeyPublicExponent is the public exponent of the key pair.
 2.120. 
Generation 2:

Reference to a record type. This data type is used in RecordArrays.

Value assignment:


 ActivityChangeInfo,CardSlotsStatus,CurrentDateTime,MemberStateCertificate,OdometerValueMidnight,DateOfDayDownloaded,SensorPaired,Signature,SpecificConditionRecord,VehicleIdentificationNumber,VehicleRegistrationNumber,VuCalibrationRecord,VuCardIWRecord,VuCardRecord,VuCertificate,VuCompanyLocksRecord,VuControlActivityRecord,VuDetailedSpeedBlock,VuDownloadablePeriod,VuDownloadActivityData,VuEventRecord,VuGNSSADRecord,VuITSConsentRecord,VuFaultRecord,VuIdentification,VuOverSpeedingControlData,VuOverSpeedingEventRecord,VuPlaceDailyWorkPeriodRecord,VuTimeAdjustmentGNSSRecord,VuTimeAdjustmentRecord,VuPowerSupplyInterruptionRecord,SensorPairedRecord,SensorExternalGNSSCoupledRecord,RFU,Manufacturer specific.
 2.121. 
Alphabetic reference to a region within a specified country.


 Generation 1:
Value assignment:

 Generation 2:
The RegionAlpha codes shall be held on a list maintained on the website of the laboratory appointed to carry out interoperability testing.
 2.122. 
Numerical reference to a region within a specified country.


 Generation 1:
Value assignment:

 Generation 2:
The RegionNumeric codes shall be held on a list maintained on the website of the laboratory appointed to carry out interoperability testing.
 2.123. 
Generation 2:

Serial number of the Remote Communication Module.
 2.124. 
Generation 1:

The modulus of a RSA key pair.

Value assignment: Unspecified.
 2.125. 
Generation 1:

The private exponent of a RSA key pair.

Value assignment: Unspecified.
 2.126. 
Generation1:

The public exponent of a RSA key pair.

Value assignment: Unspecified.
 2.127. 
Generation2:

For the definition of this data type see Appendix 14.
 2.128. 
Generation 2:

This data type stores information about the seals that are attached to the different components of a vehicle and is intended for storage on a card. This data type is related to Annex 1C requirement 337.

noOfSealRecords is the number of records in sealRecords.

sealRecords is a set of seal records.
 2.129. 
Generation 2:

This data type stores information about the seals that are attached to the different components of a vehicle and is intended for storage in a Vehicle Unit.

sealRecords is a set of seal records. If there are less than 5 seals available the value of the EquipmentType in all unused sealRecords shall be set to 16, i.e. unused.
 2.130. 
Generation 2:

This data type stores information about a seal that is attached to a component. This data type is related to Annex 1C requirement 337.

equipmentType identifies the type of equipment the seal is attached to.

extendedSealIdentifier is the identifier of the seal attached to the equipment.
 2.131. 
Type approval number of the sensor.


 Generation 1:

Value assignment: Unspecified.
 Generation 2:

Value assignment:
The approval number shall be provided as published on the corresponding European Commission web site, i.e. for example including hyphens if any. The approval number shall be left-aligned.
 2.132. 
Generation 2:

Type approval number of the external GNSS facility.

Value assignment:

The approval number shall be provided as published on the corresponding European Commission web site, i.e. for example including hyphens if any. The approval number shall be left-aligned.
 2.133. 
Generation 2:

Information, stored in a vehicle unit, related to the identification of the external GNSS facility coupled with the vehicle unit (Annex 1C requirement 100).

sensorSerialNumber is the serial number of the external GNSS facility coupled with the vehicle unit.

sensorApprovalNumber is the approval number of this external GNSS facility.

sensorCouplingDate is a date of coupling of this external GNSS facility with the vehicle unit.
 2.134. 
Generation 2:

Information related to the identification of the external GNSS facility (Annex 1C requirement 98).

sensorSerialNumber is the extended serial number of the external GNSS facility.

sensorApprovalNumber is the approval number of the external GNSS facility.

sensorSCIdentifier is the identifier of the security component of the external GNSS facility.

sensorOSIdentifier is the identifier of the operating system of the external GNSS facility.
 2.135. 
Generation 2:

Information, stored in an external GNSS facility, related to the installation of the external GNSS sensor (Annex 1C requirement 123).

sensorCouplingDateFirst is the date of the first coupling of external GNSS facility with a vehicle unit.

firstVuApprovalNumber is the approval number of the first vehicle unit coupled with the external GNSS facility.

firstVuSerialNumber is the serial number of the first vehicle unit paired with the external GNSS facility.

sensorCouplingDateCurrent is the date of the current coupling of external GNSS facility with a vehicle unit.

currentVuApprovalNumber is the approval number of the vehicle unit currently coupled with the external GNSS facility.

currentVUSerialNumber is the serial number of the vehicle unit currently coupled with the external GNSS facility.
 2.136. 
Generation 2:

Identifier of the operating system of the external GNSS facility.

Value assignment: manufacturer specific.
 2.137. 
Generation 2:

This type is used e.g. to identify the cryptographic module of the external GNSS facility.

Identifier of the security component of the external GNSS facility.

Value assignment: component manufacturer specific.
 2.138. 
Generation 2:

Date of a coupling of the external GNSS facility with a vehicle unit.

Value assignment: Unspecified.
 2.139. 
Generation 2:

This type is used to store the serial number of the GNSS receiver both when it is inside the VU and when it is outside the VU.

Serial number of the GNSS receiver.
 2.140. 
Information, stored in a motion sensor, related to the identification of the motion sensor (Annex 1B requirement 077 and Annex 1C requirement 95).

sensorSerialNumber is the extended serial number of the motion sensor (includes part number and manufacturer code).

sensorApprovalNumber is the approval number of the motion sensor.

sensorSCIdentifier is the identifier of the security component of the motion sensor.

sensorOSIdentifier is the identifier of the operating system of the motion sensor.
 2.141. 
Information, stored in a motion sensor, related to the installation of the motion sensor (Annex 1B requirement 099 and Annex 1C requirement 122).

sensorPairingDateFirst is the date of the first pairing of the motion sensor with a vehicle unit.

firstVuApprovalNumber is the approval number of the first vehicle unit paired with the motion sensor.

firstVuSerialNumber is the serial number of the first vehicle unit paired with the motion sensor.

sensorPairingDateCurrent is the date of the current pairing of the motion sensor with the vehicle unit.

currentVuApprovalNumber is the approval number of the vehicle unit currently paired with the motion sensor.

currentVUSerialNumber is the serial number of the vehicle unit currently paired with the motion sensor.
 2.142. 
Information, stored in a workshop card, related to the security data needed for pairing motion sensors to vehicle units (Annex 1C requirement 308 and 331).


 Generation 1:

Value assignment: in accordance with ISO 16844-3.
 Generation 2:
As described in Appendix 11 a workshop card shall store up to three keys for VU Motion Sensor pairing. These keys have different key versions.

 2.143. 
Identifier of the operating system of the motion sensor.

Value assignment: manufacturer specific.
 2.144. 
Generation 1:

Information, stored in a vehicle unit, related to the identification of the motion sensor paired with the vehicle unit (Annex 1B requirement 079).

sensorSerialNumber is the serial number of the motion sensor currently paired with the vehicle unit.

sensorApprovalNumber is the approval number of the motion sensor currently paired with the vehicle unit.

sensorPairingDateFirst is the date of the first pairing with a vehicle unit of the motion sensor currently paired with the vehicle unit.
 2.145. 
Generation 2:

Information, stored in a vehicle unit, related to the identification of a motion sensor paired with the vehicle unit (Annex 1C requirement 97).

sensorSerialNumber is the serial number of a motion sensor paired with the vehicle unit.

sensorApprovalNumber is the approval number of this motion sensor.

sensorPairingDate is a date of pairing of this motion sensor with the vehicle unit.
 2.146. 
Date of a pairing of the motion sensor with a vehicle unit.

Value assignment: Unspecified.
 2.147. 
Identifier of the security component of the motion sensor.

Value assignment: component manufacturer specific.
 2.148. 
Serial number of the motion sensor.
 2.149. 
A digital signature.


 Generation 1:

Value assignment: in accordance with Appendix 11 Common security mechanisms.
 Generation 2:

Value assignment: in accordance with Appendix 11 Common security mechanisms.
 2.150. 
Generation 2:

A set of signatures plus metadata used in the download protocol.

recordType denotes the type of the record (Signature). Value Assignment: See RecordType

recordSize is the size of the Signature in bytes.

noOfRecords is the number of records in the set records. The value shall be set to 1 as the signatures may have different lengths.

records is the set of signatures.
 2.151. 
The number of similar events for one given day (Annex 1B requirement 094 and Annex 1C requirement 117).

Value assignment: 0 is not used, 1 means that only one event of that type has occurred and has been stored on that day, 2 means that 2 events of that type has occurred on that day (one only has been stored), …255 means that 255 or more events of that type have occurred on that day.
 2.152. 
Information, stored in a driver card, a workshop card or a vehicle unit, related to a specific condition (requirements Annex 1C 130, 276, 301, 328, and 355).

entryTime is the date and time of the entry.

specificConditionType is the code identifying the specific condition.
 2.153. 
Information, stored in a driver card, a workshop card or a vehicle unit, related to a specific condition (Annex 1C requirement 131, 277, 302, 329, and 356).

Generation 2:

conditionPointerNewestRecord is the index of the last updated specific condition record.

Value assignment: Number corresponding to the numerator of the specific condition record, beginning with ‘0’ for the first occurrence of the specific condition record in the structure.

specificConditionRecords is the set of records containing information on the specific conditions recorded.
 2.154. 
Code identifying a specific condition (Annex 1B requirements 050b, 105a, 212a and 230a and Annex 1C requirements 62).


 Generation 1:
Value assignment:
‘00’HRFU‘01’HOut of scope — Begin‘02’HOut of scope — End‘03’HFerry / Train crossing‘04’H .. ‘FF’HRFU
 Generation 2:
Value assignment:
‘00’HRFU‘01’HOut of scope — Begin‘02’HOut of scope — End‘03’HFerry / Train crossing — Begin‘04’HFerry / Train crossing — End‘05’H .. ‘FF’HRFU
 2.155. 
Speed of the vehicle (km/h).

Value assignment: kilometers per hour in the operational range 0 to 220 km/h.
 2.156. 
Maximum authorised Speed of the vehicle (definition hh)).
 2.157. 
Average speed in a previously defined duration (km/h).
 2.158. 
Maximum speed measured in a previously defined duration.
 2.159. 
Generation 2:

For the definition of this data type see Appendix 14.
 2.160.  2.161. 
Generation 1:

A triple DES session key.

Value assignment: not further specified.
 2.162. 
Code for a combined date and time field, where the date and time are expressed as seconds past 00h.00m.00s. on 1 January 1970 UTC.




                                    Value assignment
                                  – 
                                    Octet aligned
                                 : Number of seconds since midnight 1 January 1970 UTC.

The max. possible date/time is in the year 2106.
 2.163. 
Designation of tyre dimensions.

Value assignment: in accordance with Directive 92/23 (EEC) 31/03/92 O.J. L129 p.95.
 2.164. 
Vehicle Identification Number (VIN) referring to the vehicle as a whole, normally chassis serial number or frame number.

Value assignment: As defined in ISO 3779.
 2.165. 
Generation 2:

The Vehicle Idenification Number plus metadata as used in the download protocol.

recordType denotes the type of the record (VehicleIdentificationNumber). Value Assignment: See RecordType

recordSize is the size of the VehicleIdentificationNumber in bytes.

noOfRecords is the number of records in the set records.

records is the set of vehicle identification numbers.
 2.166. 
Identification of a vehicle, unique for Europe (VRN and Member State).

vehicleRegistrationNation is the nation where the vehicle is registered.

vehicleRegistrationNumber is the registration number of the vehicle (VRN).
 2.167. 
Registration number of the vehicle (VRN). The registration number is assigned by the vehicle licensing authority.

codePage specifies a character set defined in Chapter 4,

vehicleRegNumber is a VRN encoded using the specified character set.

Value assignment: Country specific.
 2.168. 
Generation 2:

The Vehicle Registration Number plus metadata as used in the download protocol.

recordType denotes the type of the record (VehicleRegistrationNumber). Value Assignment: See RecordType

recordSize is the size of the VehicleRegistrationNumber in bytes.

noOfRecords is the number of records in the set records.

records is the set of vehicle registration numbers.
 2.169. 
Generation 2:

Information stored in a VU on the ability of the VU to use generation 1 tachograph cards or not (Annex 1C requirement 121).

Value assignment — Octet Aligned:‘xxxxxxxa’B (8 bits)

For the ability to support of generation 1:

‘a’BAbility to support generation 1 tachograph cards:
 ‘0’ B Generation 1 is supported,
 ‘1’B Generation1 is not supported,‘xxxxxxx’BRFU
 2.170. 
Generation 1:

Information, stored in a VU, related to changes of activity and/or changes of driving status and/or changes of card status for a given calendar day (Annex 1B requirement 084 and Annex 1C requirement 105, 106, 107) and to slots status at 00:00 that day.

noOfActivityChanges is the number of ActivityChangeInfo words in the activityChangeInfos set.

activityChangeInfos is the set of ActivityChangeInfo words stored in the VU for the day. It always includes two ActivityChangeInfo words giving the status of the two slots at 00:00 that day.
 2.171. 
Generation 2:

Information, stored in a VU, related to changes of activity and/or changes of driving status and/or changes of card status for a given calendar day (Annex 1C requirement 105, 106, 107) and to slots status at 00:00 that day.

recordType denotes the type of the record (ActivityChangeInfo). Value Assignment: See RecordType

recordSize is the size of the ActivityChangeInfo in bytes.

noOfRecords is the number of records in the set records.

records is the set of ActivityChangeInfo words stored in the VU for the day. It always includes two ActivityChangeInfo words giving the status of the two slots at 00:00 that day.
 2.172. 
Type approval number of the vehicle unit.


 Generation 1:

Value assignment: Unspecified.
 Generation 2:

Value assignment:
The approval number shall be provided as published on the corresponding European Commission web site, i.e. for example including hyphens if any. The approval number shall be left-aligned.
 2.173. 
Generation 1:

Information, stored in a vehicle unit, related to the calibrations of the recording equipment (Annex 1B requirement 098).

noOfVuCalibrationRecords is the number of records contained in the vuCalibrationRecords set.

vuCalibrationRecords is the set of calibration records.
 2.174. 
Information, stored in a vehicle unit, related a calibration of the recording equipment (Annex 1B requirement 098 and Annex 1C requirement 119 and 120).


 Generation 1:

calibrationPurpose is the purpose of the calibration.
workshopName, workshopAddress are the workshop name and address.
workshopCardNumber identifies the workshop card used during the calibration.
workshopCardExpiryDate is the card expiry date.
vehicleIdentificationNumber is the VIN.
vehicleRegistrationIdentification contains the VRN and registering Member State.
wVehicleCharacteristicConstant is the characteristic coefficient of the vehicle.
kConstantOfRecordingEquipment is the constant of the recording equipment.
lTyreCircumference is the effective circumference of the wheel tyres.
tyreSize is the designation of the dimension of the tyres mounted on the vehicle
authorisedSpeed is the authorised speed of the vehicle.
oldOdometerValue, newOdometerValue are the old and new values of the odometer.
oldTimeValue, newTimeValue are the old and new values of date and time.
nextCalibrationDate is the date of the next calibration of the type specified in CalibrationPurpose to be carried out by the authorised inspection authority.
 Generation 2:

In addition to generation 1 the following data element is used:
sealDataVu gives information about the seals that are attached to different components of the vehicle.
 2.175. 
Generation 2:

Information, stored in a vehicle unit, related to the calibrations of the recording equipment (Annex 1C requirement 119 and 120).

recordType denotes the type of the record (VuCalibrationRecord). Value Assignment: See RecordType

recordSize is the size of the VuCalibrationRecord in bytes.

noOfRecords is the number of records in the set records.

records is the set of calibration records.
 2.176. 
Generation 1:

Information, stored in a vehicle unit, related to insertion and withdrawal cycles of driver cards or of workshop cards in the vehicle unit (Annex 1B requirement 081 and Annex 1C requirement 103).

noOfIWRecords is the number of records in the set vuCardIWRecords.

vuCardIWRecords is a set of records related to card insertion withdrawal cycles.
 2.177. 
Information, stored in a vehicle unit, related to an insertion and withdrawal cycle of a driver card or of a workshop card in the vehicle unit (Annex 1B requirement 081 and Annex 1C requirement 102).


 Generation 1:

cardHolderName is the driver or workshop card holder's surname and first names as stored in the card.
fullCardNumber is the type of card, its issuing Member State and its card number as stored in the card.
cardExpiryDate is the card's expiry date as stored in the card.
cardInsertionTime is the insertion date and time.
vehicleOdometerValueAtInsertion is the vehicle odometer value at card insertion.
cardSlotNumber is the slot in which the card is inserted.
cardWithdrawalTime is the withdrawal date and time.
vehicleOdometerValueAtWithdrawal is the vehicle odometer value at card withdrawal.
previousVehicleInfo contains information about the previous vehicle used by the driver, as stored in the card.
manualInputFlag is a flag identifying if the cardholder has manually entered driver activities at card insertion.
 Generation 2:

Instead of fullCardNumber the generation 2 data structure makes use of the following data element.
fullCardNumberAndGeneration is the type of card, its issuing Member State, its card number and generation as stored in the card.
 2.178. 
Generation 2:

Information, stored in a vehicle unit, related to insertion and withdrawal cycles of driver cards or of workshop cards in the vehicle unit (Annex 1C requirement 103).

recordType denotes the type of the record (VuCardIWRecord). Value Assignment: See RecordType

recordSize is the size of the VuCardIWRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of records related to card insertion withdrawal cycles.
 2.179. 
Generation 2:

Information, stored in a vehicle unit, about a tachograph card used (Annex IC requirement 132).




                                    cardNumberAndGenerationInformation
                                  is the full card number and generation of the card used (data type 2.74).


                                    cardExtendedSerialNumber
                                  as read from the file EF_ICC under the MF of the card.


                                    cardStructureVersion
                                  as read from the file EF_Application_Identification under the DF_Tachograph_G2.


                                    cardNumber
                                  as read from the file EF_Identification under the DF_Tachograph_G2.
 2.180. 
Generation 2:

Information stored in a vehicle unit about the tachograph cards used with this VU. This information is intended for the analysis of VU — card problems (Annex 1C requirement 132).

recordType denotes the type of the record (VuCardRecord). Value Assignment: See RecordType

recordSize is the size of the VuCardRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of records related to the tachograph cards used with the VU.
 2.181. 
Certificate of the public key of a vehicle unit.
 2.182. 
Generation 2:

The VU certificate plus metadata as used in the download protocol.

recordType denotes the type of the record (VuCertificate). Value Assignment: See RecordType

recordSize is the size of the VuCertificate in bytes.

noOfRecords is the number of records in the set records. The value shall be set to 1 as the certificates may have different lengths.

records is a set of VU certificates.
 2.183. 
Generation 1:

Information, stored in a vehicle unit, related to company locks (Annex 1B requirement 104).

noOfLocks is the number of locks listed in vuCompanyLocksRecords.

vuCompanyLocksRecords is the set of company locks records.
 2.184. 
Information, stored in a vehicle unit, related to one company lock (Annex 1B requirement 104 and Annex 1C requirement 128).


 Generation 1:

lockInTime, lockOutTime are the date and time of lock-in and lock-out.
companyName, companyAddress are the company name and address related with the lock-in.
companyCardNumber identifies the card used at lock-in.
 Generation 2:

Instead of companyCardNumber the generation 2 data structure makes use of the following data element.
companyCardNumberAndGeneration identifies the card including its generation used at lock-in.
 2.185. 
Generation 2:

Information, stored in a vehicle unit, related to company locks (Annex 1C requirement 128).

recordType denotes the type of the record (VuCompanyLocksRecord). Value Assignment: See RecordType

recordSize is the size of the VuCompanyLocksRecord in bytes.

noOfRecords is the number of records in the set records. Value 0..255.

records is the set of company locks records.
 2.186. 
Generation 1:

Information, stored in a vehicle unit, related to controls performed using this VU (Annex 1B requirement 102).

noOfControls is the number of controls listed in vuControlActivityRecords.

vuControlActivityRecords is the set of control activity records.
 2.187. 
Information, stored in a vehicle unit, related to a control performed using this VU (Annex 1B requirement 102 and Annex 1C requirement 126).


 Generation 1:

controlType is the type of the control.
controlTime is the date and time of the control.
controlCardNumber identifies the control card used for the control.
downloadPeriodBeginTime is the begin time of the downloaded period, in case of downloading.
downloadPeriodEndTime is the end time of the downloaded period, in case of downloading.
 Generation 2:

Instead of controlCardNumber the generation 2 data structure makes use of the following data element.
controlCardNumberAndGeneration identifies the control card including its generation used for the control.
 2.188. 
Generation 2:

Information, stored in a vehicle unit, related to controls performed using this VU (Annex 1C requirement 126).

recordType denotes the type of the record (VuControlActivityRecord). Value Assignment: See RecordType

recordSize is the size of the VuControlActivityRecord in bytes.

noOfRecords is the number of records in the set records.

records is the set of VU control activity records.
 2.189. 
Counter, stored in a card, identifying sequentially the insertion withdrawal cycles of the card in vehicle units.

Value assignment: Consecutive Number with max, value 9 999, starting again with 0.
 2.190. 
Information, stored in a vehicle unit, related to the vehicle's detailed speed for a minute during which the vehicle has been moving (Annnex 1B requirement 093 and Annex 1C requirement 116).

speedBlockBeginDate is the date and time of the first speed value within the block.

speedsPerSecond is the chronological sequence of measured speeds every seconds for the minute starting at speedBlockBeginDate (included).
 2.191. 
Generation 2:

Information, stored in a vehicle unit, related to the detailed speed of the vehicle.

recordType denotes the type of the record (VuDetailedSpeedBlock). Value Assignment: See RecordType

recordSize is the size of the VuDetailedSpeedBlock in bytes.

noOfRecords is the number of records in the set records.

records is the set of detailed speed blocks.
 2.192. 
Generation 1:

Information, stored in a vehicle unit, related to the detailed speed of the vehicle.

noOfSpeedBlocks is the number of speed blocks in the vuDetailedSpeedBlocks set.

vuDetailedSpeedBlocks is the set of detailed speed blocks.
 2.193. 
Oldest and latest dates for which a vehicle unit holds data related to drivers activities (Annex 1B requirements 081, 084 or 087 and Annex 1C requirements 102, 105, 108).

minDownloadableTime is the oldest card insertion or activity change or place entry date and time stored in the VU.

maxDownloadableTime is the latest card withdrawal or activity change or place entry date and time stored in the VU.
 2.194. 
Generation 2:

The VUDownloadablePeriod plus metadata used in the download protocol.

recordType denotes the type of the record (VuDownloadablePeriod). Value Assignment: See RecordType

recordSize is the size of the VuDownloadablePeriod in bytes.

noOfRecords is the number of records in the set records.

records is the set of VuDownloadablePeriod records.
 2.195. 
Information, stored in a vehicle unit, related to its last download (Annex 1B requirement 105 and Annex 1C requirement 129).


 Generation 1:

downloadingTime is the date and time of downloading.
fullCardNumber identifies the card used to authorise the download.
companyOrWorkshopName is the company or workshop name.
 Generation 2:

Instead of fullCardNumber the generation 2 data structure makes use of the following data element.
fullCardNumberAndGeneration identifies the card including its generation used to authorise the download.
 2.196. 
Generation 2:

Information related to the last VU download (Annex 1C requirement 129).

recordType denotes the type of the record (VuDownloadActivityData). Value Assignment: See RecordType

recordSize is the size of the VuDownloadActivityData in bytes.

noOfRecords is the number of records in the set records.

records is the set of download activity data records.
 2.197. 
Generation 1:

Information, stored in a vehicle unit, related to events (Annex 1B requirement 094 except over speeding event).

noOfVuEvents is the number of events listed in the vuEventRecords set.

vuEventRecords is a set of events records.
 2.198. 
Information, stored in a vehicle unit, related to an event (Annex 1B requirement 094 and Annex 1C requirement 117 except over speeding event).


 Generation 1:

eventType is the type of the event.
eventRecordPurpose is the purpose for which this event has been recorded.
eventBeginTime is the date and time of beginning of event.
eventEndTime is the date and time of end of event.
cardNumberDriverSlotBegin identifies the card inserted in the driver slot at the beginning of the event.
cardNumberCodriverSlotBegin identifies the card inserted in the co-driver slot at the beginning of the event.
cardNumberDriverSlotEnd identifies the card inserted in the driver slot at the end of the event.
cardNumberCodriverSlotEnd identifies the card inserted in the co-driver slot at the end of the event.
similarEventsNumber is the number of similar events that day.
This sequence can be used for all events other than over speeding events.
 Generation 2:

In addition to generation 1 the following data elements are used:
manufacturerSpecificEventFaultData contains additional, manufacturer specific information about the event.
Instead of cardNumberDriverSlotBegin, cardNumberCodriverSlotBegin, cardNumberDriverSlotEnd, and cardNumberCodriverSlotEnd the generation 2 data structure makes use of the following data elements:

 cardNumberAndGenDriverSlotBegin identifies the card including its generation which is inserted in the driver slot at the beginning of the event.
 cardNumberAndGenCodriverSlotBegin identifies the card including its generation which is inserted in the co-driver slot at the beginning of the event.
 cardNumberAndGenDriverSlotEnd identifies the card including its generation which is inserted in the driver slot at the end of the event.
 cardNumberAndGenCodriverSlotEnd identifies the card including its generation which is inserted in the co-driver slot at the end of the event.If the event is a time conflict the eventBeginTime and eventEndTime are to be interpreted as follows:
 eventBeginTime is the recording equipment date and time.
 eventEndTime is the GNSS date and time.
 2.199. 
Generation 2:

Information, stored in a vehicle unit, related to events (Annex 1C requirement 117 except over speeding event).

recordType denotes the type of the record (VuEventRecord). Value Assignment: See RecordType

recordSize is the size of the VuEventRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of events records.
 2.200. 
Generation 1:

Information, stored in a vehicle unit, related to faults (Annex 1B requirement 096).

noOfVuFaults is the number of faults listed in the vuFaultRecords set.

vuFaultRecords is a set of faults records.
 2.201. 
Information, stored in a vehicle unit, related to a fault (Annex 1B requirement 096 and Annex 1C requirement 118).


 Generation 1:

faultType is the type of recording equipment fault.
faultRecordPurpose is the purpose for which this fault has been recorded.
faultBeginTime is the date and time of beginning of fault.
faultEndTime is the date and time of end of fault.
cardNumberDriverSlotBegin identifies the card inserted in the driver slot at the beginning of the fault.
cardNumberCodriverSlotBegin identifies the card inserted in the co-driver slot at the beginning of the fault.
cardNumberDriverSlotEnd identifies the card inserted in the driver slot at the end of the fault.
cardNumberCodriverSlotEnd identifies the card inserted in the co-driver slot at the end of the fault.
 Generation 2:

In addition to generation 1 the following data element is used:
manufacturerSpecificEventFaultData contains additional, manufacturer specific information about the fault.
Instead of cardNumberDriverSlotBegin, cardNumberCodriverSlotBegin, cardNumberDriverSlotEnd, and cardNumberCodriverSlotEnd the generation 2 data structure makes use of the following data elements:
 cardNumberAndGenDriverSlotBegin identifies the card including its generation which is inserted in the driver slot at the beginning of the fault.
 cardNumberAndGenCodriverSlotBegin identifies the card including its generation which is inserted in the co-driver slot at the beginning of the fault.
 cardNumberAndGenDriverSlotEnd identifies the card including its generation which is inserted in the driver slot at the end of the fault.
 cardNumberAndGenCodriverSlotEnd identifies the card including its generation which is inserted in the co-driver slot at the end of the fault.
 2.202. 
Generation 2:

Information, stored in a vehicle unit, related to faults (Annex 1C requirement 118).

recordType denotes the type of the record (VuFaultRecord). Value Assignment: See RecordType

recordSize is the size of the VuFaultRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of faults records.
 2.203. 
Generation 2:

Information, stored in a vehicle unit, related to the GNSS position of the vehicle if the accumulated driving time reaches a multiple of three hours (Annex IC requirement 108, 110).




                                    timeStamp
                                  is the date and time when the accumulated driving time reaches a multiple of three hours.


                                    cardNumberAndGenDriverSlot
                                  identifies the card including its generation which is inserted in the driver slot.


                                    cardNumberAndGenCodriverSlot
                                  identifies the card including its generation which is inserted in the co-driver slot.


                                    gnssPlaceRecord
                                  contains information related to the position of the vehicle.


                                    vehicleOdometerValue
                                  is the odometer value when the accumulated driving time reaches a multiple of three hours.
 2.204. 
Generation 2:

Information, stored in a vehicle unit, related to the GNSS position of the vehicle if the accumulated driving time reaches a multiple of three hours (Annex IC requirement 108 and 110).




                                    recordType
                                  denotes the type of the record (VuGNSSADRecord).


                                    Value Assignment
                                 : See RecordType.


                                    recordSize
                                  is the size of the VuGNSSADRecord in bytes.


                                    noOfRecords
                                  is the number of records in the set records.


                                    records
                                  is a set of GNSS accumulated driving records.
 2.205. 
Information, stored in a vehicle unit, related to the identification of the vehicle unit (Annex 1B requirement 075 and Annex 1C requirement 93 and 121).


 Generation 1:

vuManufacturerName is the name of the manufacturer of the vehicle unit.
vuManufacturerAddress is the address of the manufacturer of the vehicle unit.
vuPartNumber is the part number of the vehicle unit.
vuSerialNumber is the serial number of the vehicle unit.
vuSoftwareIdentification identifies the software implemented in the vehicle unit.
vuManufacturingDate is the manufacturing date of the vehicle unit.
vuApprovalNumber is the type approval number of the vehicle unit.
 Generation 2:

In addition to generation 1 the following data element are used:
 vuGeneration identifies the generation of the vehicle unit.
 vuAbility provides information whether the VU supports generation 1 tachograph cards or not.
 2.206. 
Generation 2:

The VuIdentification plus metadata used in the download protocol.

recordType denotes the type of the record (VuIdentification). Value Assignment: See RecordType

recordSize is the size of the VuIdentification in bytes.

noOfRecords is the number of records in the set records.

records is a set of VuIdentification records.
 2.207. 
Generation 2:

Information stored in a vehicle unit, related to the consent of a driver to use Intelligent Transport Systems.

cardNumberAndGen identifies the card including its generation. This must be a driver card or a workshop card.

consent is a flag which indicates whether the driver has given his consent on the usage of Intelligent Transport Systems with this vehicle / vehicle unit.

Value assignment:

TRUEindicates the driver's consent to use Intelligent Transport SystemsFALSEindicates the driver's denial to use Intelligent Transport Systems
 2.208. 
Generation 2:

Information, stored in a vehicle unit, related to drivers' consent on the usage of Intelligent Transport Systems (Annex 1C requirement 200).

recordType denotes the type of the record (VuITSConsentRecord). Value Assignment: See RecordType

recordSize is the size of the VuITSConsentRecord in bytes.

noOfRecords is the number of records in the set records.

records is the set of ITS consent records.
 2.209. 
Address of the manufacturer of the vehicle unit.

Value assignment: Unspecified.
 2.210. 
Name of the manufacturer of the vehicle unit.

Value assignment: Unspecified.
 2.211. 
Date of manufacture of the vehicle unit.

Value assignment: Unspecified.
 2.212. 
Information, stored in a vehicle unit, related to over speeding events since the last over speeding control (Annex 1B requirement 095 and Annex 1C requirement 117).

lastOverspeedControlTime is the date and time of the last over speeding control.

firstOverspeedSince is the date and time of the first over speeding following this over speeding control.

numberOfOverspeedSince is the number of over speeding events since the last over speeding control.
 2.213. 
Generation 2:

The VuOverSpeedingControlData plus metadata used in the download protocol.

recordType denotes the type of the record (VuOverSpeedingControlData). Value Assignment: See RecordType

recordSize is the size of the VuOverSpeedingControlData in bytes.

noOfRecords is the number of records in the set records.

records is a set of over speeding control data records.
 2.214. 
Generation 1:

Information, stored in a vehicle unit, related to over speeding events (Annex 1B requirement 094).

noOfVuOverSpeedingEvents is the number of events listed in the vuOverSpeedingEventRecords set.

vuOverSpeedingEventRecords is a set of over speeding events records.
 2.215. 

 Generation 1:
Information, stored in a vehicle unit, related to over speeding events (Annex 1B requirement 094 and Annex 1C requirement 117).

eventType is the type of the event.
eventRecordPurpose is the purpose for which this event has been recorded.
eventBeginTime is the date and time of beginning of event.
eventEndTime is the date and time of end of event.
maxSpeedValue is the maximum speed measured during the event.
averageSpeedValue is the arithmetic average speed measured during the event.
cardNumberDriverSlotBegin identifies the card inserted in the driver slot at the beginning of the event.
similarEventsNumber is the number of similar events that day.
 Generation 2:
Information, stored in a vehicle unit, related to over speeding events (Annex 1B requirement 094 and Annex 1C requirement 117).

Instead of cardNumberDriverSlotBegin, the generation 2 data structure makes use of the following data element:
cardNumberAndGenDriverSlotBegin identifies the card including its generation which is inserted in the driver slot at the beginning of the event.
 2.216. 
Generation 2:

Information, stored in a vehicle unit, related to over speeding events (Annex 1C requirement 117).

recordType denotes the type of the record (VuOverSpeedingEventRecord). Value Assignment: See RecordType

recordSize is the size of the VuOverSpeedingEventRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of over speeding events records.
 2.217. 
Part number of the vehicle unit.

Value assignment: VU manufacturer specific.
 2.218. 
Generation 1:

Information, stored in a vehicle unit, related to places where drivers begin or end a daily work period (Annex 1B requirement 087 and Annex 1C requirement 108 and 110).

noOfPlaceRecords is the number of records listed in the vuPlaceDailyWorkPeriodRecords set.

vuPlaceDailyWorkPeriodRecords is a set of place related records.
 2.219. 

 Generation 1:
Information, stored in a vehicle unit, related to a place where a driver begins or ends a daily work period (Annex 1B requirement 087 and Annex 1C requirement 108 and 110).

fullCardNumber is the driver's card type, card issuing Member State and card number.
placeRecord contains the information related to the place entered.
 Generation 2:
Information, stored in a vehicle unit, related to a place where a driver begins or ends a daily work period (Annex 1B requirement 087 and Annex 1C requirement 108 and 110).

Instead of fullCardNumber, the generation 2 data structure makes use of the following data element:
fullCardNumberAndGeneration is the type of card, its issuing Member State, its card number and generation as stored in the card.
 2.220. 
Generation 2:

Information, stored in a vehicle unit, related to places where drivers begin or end a daily work period (Annex 1C requirement 108 and 110).

recordType denotes the type of the record (VuPlaceDailyWorkPeriodRecord). Value Assignment: See RecordType

recordSize is the size of the VuPlaceDailyWorkPeriodRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of place related records.
 2.221. 
Generation 1:

The private key of a vehicle unit.
 2.222. 
Generation 1:

The public key of a vehicle unit.
 2.223. 
Serial number of the vehicle unit (Annex 1B requirement 075 and Annex 1C requirement 93).
 2.224. 
Date of installation of the vehicle unit software version.

Value assignment: Unspecified.
 2.225. 
Information, stored in a vehicle unit, related to the software installed.

vuSoftwareVersion is the software version number of the Vehicle Unit.

vuSoftInstallationDate is the software version installation date.
 2.226. 
Software version number of the vehicle unit.

Value assignment: Unspecified.
 2.227. 
Generation 1:

Information, stored in a vehicle unit, related to specific conditions.

noOfSpecificConditionRecords is the number of records listed in the specificConditionRecords set.

specificConditionRecords is a set of specific conditions related records.
 2.228. 
Generation 2:

Information, stored in a vehicle unit, related to specific conditions (Annex 1C requirement 130).

recordType denotes the type of the record (SpecificConditionRecord). Value Assignment: See RecordType

recordSize is the size of the SpecificConditionRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of specific conditions related records.
 2.229. 
Generation 1:

Information, stored in a vehicle unit, related to time adjustments performed outside the frame of a regular calibration (Annex 1B requirement 101).

noOfVuTimeAdjRecords is the number of records in vuTimeAdjustmentRecords.

vuTimeAdjustmentRecords is a set of time adjustment records.
 2.230.  2.231.  2.232. 
Information, stored in a vehicle unit, related a time adjustment performed outside the frame of a regular calibration (Annex 1B requirement 101 and Annex 1C requirement 124 and 125).


 Generation 1:

oldTimeValue, newTimeValue are the old and new values of date and time.
workshopName, workshopAddress are the workshop name and address.
workshopCardNumber identifies the workshop card used to perform the time adjustment.
 Generation 2:

Instead of workshopCardNumber the generation 2 data structure makes use of the following data element.
workshopCardNumberAndGeneration identifies the workshop card including its generation used to perform the time adjustment.
 2.233. 
Generation 2:

Information, stored in a vehicle unit, related to time adjustments performed outside the frame of a regular calibration (Annex 1C requirement 124 and 125).

recordType denotes the type of the record (VuTimeAdjustmentRecord). Value Assignment: See RecordType

recordSize is the size of the VuTimeAdjustmentRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of time adjustment records.
 2.234. 
Information, stored in a workshop card related to the identification of the application of the card (Annex 1C requirement 307 and 330).


 Generation 1:

typeOfTachographCardId is specifying the implemented type of card.
cardStructureVersion is specifying the the version of the structure that is implemented in the card.
noOfEventsPerType is the number of events per type of event the card can record.
noOfFaultsPerType is the number of faults per type of fault the card can record.
activityStructureLength indicates the number of bytes available for storing activity records.
noOfCardVehicleRecords is the number of vehicle records the card can contain.
noOfCardPlaceRecords is the number of places the card can record.
noOfCalibrationRecords is the number of calibration records the card can store.
 Generation 2:

In addition to generation 1 the following data elements are used:

                                             noOfGNSSADRecords
                                           is the number of GNSS accumulated driving records the card can store.

                                             noOfSpecificConditionRecords
                                           is the number of specific condition records the card can store.

                                             noOfCardVehicleUnitRecords
                                           is the number of vehicle units used records the card can store.
 2.235. 
Information, stored in a workshop card, related to workshop activity performed with the card (Annex 1C requirements 314, 316, 337, and 339).

calibrationTotalNumber is the total number of calibrations performed with the card.

calibrationPointerNewestRecord is the index of the last updated calibration record.

Value assignment: Number corresponding to the numerator of the calibration record, beginning with ‘0’ for the first occurrence of the calibration records in the structure.

calibrationRecords is the set of records containing calibration and/or time adjustment information.
 2.236. 
Information, stored in a workshop card, related to a calibration performed with the card (Annex 1C requirement 314 and 337).


 Generation 1:

calibrationPurpose is the purpose of the calibration.
vehicleIdentificationNumber is the VIN.
vehicleRegistration contains the VRN and registering Member State.
wVehicleCharacteristicConstant is the characteristic coefficient of the vehicle.
kConstantOfRecordingEquipment is the constant of the recording equipment.
lTyreCircumference is the effective circumference of the wheel tyres.
tyreSize is the designation of the dimensions of the tyres mounted on the vehicle.
authorisedSpeed is the maximum authorised speed of the vehicle.
oldOdometerValue, newOdometerValue are the old and new values of the odometer.
oldTimeValue, newTimeValue are the old and new values of date and time.
nextCalibrationDate is the date of the next calibration of the type specified in CalibrationPurpose to be carried out by the authorised inspection authority.
vuPartNumber, vuSerialNumber and sensorSerialNumber are the data elements for recording equipment identification.
 Generation 2:

In addition to generation 1 the following data elements are used:
 sensorGNSSSerialNumber which identifies an external GNSS facility.
 rcmSerialNumber which identifies a Remote Communication Module.
 sealDataCard gives information about the seals that are attached to different components of the vehicle.
 2.237. 
Information, stored in a workshop card, related to the identification of the cardholder (Annex 1C requirement 311 and 334).

workshopName is name of the workshop of the card holder.

workshopAddress is the address of the workshop of the card holder.

cardHolderName is the name and first name(s) of the holder (e.g. the name of the mechanic).

cardHolderPreferredLanguage is the preferred language of the card holder.
 2.238. 
Personal identification number of the Workshop Card (Annex 1C requirement 309 and 332).

Value assignment: The PIN known to the cardholder, right padded with ‘FF’ bytes up to 8 bytes.
 2.239. 
Characteristic coefficient of the vehicle (definition k)).

Value assignment: Impulses per kilometer in the operating range 0 to 64 255 pulses/km.
 2.240. 
Generation 2:

Information, stored in a vehicle unit, related to Power Supply Interruption events (Annex 1C requirement 117).

eventType is the type of the event.

eventRecordPurpose is the purpose for which this event has been recorded.

eventBeginTime is the date and time of beginning of event.

eventEndTime is the date and time of end of event.

cardNumberAndGenDriverSlotBegin identifies the card including its generation inserted in the driver slot at the beginning of the event.

cardNumberAndGenDriverSlotEnd identifies the card including its generation inserted in the driver slot at the end of the event.

cardNumberAndGenCodriverSlotBegin identifies the card including its generation inserted in the co-driver slot at the beginning of the event.

cardNumberAndGenCodriverSlotEnd identifies the card including its generation inserted in the co-driver slot at the end of the event.

similarEventsNumber is the number of similar events that day.
 2.241. 
Generation 2:

Information, stored in a vehicle unit, related to Power Supply Interruption events (Annex 1C requirement 117).

recordType denotes the type of the record (VuPowerSupplyInterruptionRecord). Value Assignment: See RecordType

recordSize is the size of the VuPowerSupplyInterruptionRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of power supply interruption events records.
 2.242. 
Generation 2:

A set of SensorExternalGNSSCoupledRecord plus metadata used in the download protocol.

recordType denotes the type of the record (SensorExternalGNSSCoupledRecord). Value Assignment: See RecordType

recordSize is the size of the SensorExternalGNSSCoupledRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of Sensor External GNSS Coupled records.
 2.243. 
Generation 2:

A set of SensorPairedRecord plus metadata used in the download protocol.

recordType denotes the type of the record (SensorPairedRecord). Value Assignment: See RecordType

recordSize is the size of the SensorPairedRecord in bytes.

noOfRecords is the number of records in the set records.

records is a set of sensor paired records.
 3. 
Definition of variable values used for definitions in paragraph 2.
 4. 
IA5Strings use the ASCII characters as defined by ISO/IEC 8824-1. For readability and for easy referencing the value assignment is given below. The ISO/IEC 8824-1 supersedes this informative note in case of discrepancy.


Other character strings (Address, Name, VehicleRegistrationNumber) use, in addition, characters from the decimal character code range 161 — 255 of the following 8-bit, standard character sets, specified by the Code Page number:Standard Character Set Code Page(Decimal)
ISO/IEC 8859-1 Latin-1 Western European 1
ISO/IEC 8859-2 Latin-2 Central European 2
ISO/IEC 8859-3 Latin-3 South European 3
ISO/IEC 8859-5 Latin / Cyrillic 5
ISO/IEC 8859-7 Latin / Greek 7
ISO/IEC 8859-9 Latin-5 Turkish 9
ISO/IEC 8859-13 Latin-7 Baltic Rim 13
ISO/IEC 8859-15 Latin-9 15
ISO/IEC 8859-16 Latin-10 South Eastern European 16
KOI8-R Latin / Cyrillic 80
KOI8-U Latin / Cyrillic 85
 5. 
When encoded with ASN.1 encoding rules, all data types defined shall be encoded according to ISO/IEC 8825-2, aligned variant.
 6.  6.1. 
The Object Identifiers (OIDs) listed in this chapter are only relevant for generation 2. These OIDs are specified in TR-03110-3 and repeated here for the sake of completeness. These OIDs are contained in the subtree of bsi-de:

Example: Suppose VU Authentication is to be done with SHA-384, then the object identifier to use is (in ASN.1 notation) . The value of this object identifier in dot notation is .


 Dot notation Byte notation
  ‘04 00 7F 00 07 02 02 02 02 03’
  ‘04 00 7F 00 07 02 02 02 02 04’
  ‘04 00 7F 00 07 02 02 02 02 05’

Example: Suppose Chip Authentication is to be done by using the ECDH algorithm, resulting in an AES session key length of 128 bits. This session key will subsequently be used in the CBC mode of operation to ensure data confidentiality and with the CMAC algorithm to ensure data authenticity. Therefore, the object identifier to use is (in ASN.1 notation) . The value of this object identifier in dot notation is .


 Dot notation Byte notation
  ‘04 00 7F 00 07 02 02 03 02 02’
  ‘04 00 7F 00 07 02 02 03 02 03’
  ‘04 00 7F 00 07 02 02 03 02 04’
 6.2. 
Generation 2:

The Application Identifier (AID) for the External GNSS Facility (Generation 2) is given by ‘FF 44 54 45 47 4D’. This is a proprietary AID according to ISO/IEC 7816-4.
Note: The last 5 bytes encode DTEGM for smart Tachograph External GNSS Facility.
The Application Identifier for the generation 2 tachograph card application is given by ‘FF 53 4D 52 44 54’. This is a proprietary AID according to ISO/IEC 7816-4.

Appendix 2 1.  1.1. 
For the purpose of this appendix, the following abbreviations apply.

ACAccess conditionsAESAdvanced Encryption StandardAIDApplication IdentifierALWAlwaysAPDUApplication Protocol Data Unit (structure of a command)ATRAnswer To ResetAUTAuthenticated.C6, C7Contacts No 6 and 7 of the card as described in ISO/IEC 7816-2ccclock cyclesCHA
                                    Certificate Holder AuthorisationCHVCard holder Verification InformationCLAClass byte of an APDU commandDO
                                    Data ObjectDSRCDedicated Short Range CommunicationDFDedicated File. A DF can contain other files (EF or DF)ECCElliptic Curve CryptographyEFElementary Fileetuelementary time unitG1Generation 1G2Generation 2ICIntegrated CircuitICCIntegrated Circuit CardIDIdentifierIFDInterface DeviceIFSInformation Field SizeIFSCInformation Field Size for the cardIFSDInformation Field Size Device (for the Terminal)INSInstruction byte of an APDU commandLcLength of the input data for a APDU commandLeLength of the expected data (output data for a command)MFMaster File (root DF)NADNode Address used in T=1 protocolNEVNeverP1-P2Parameter bytesPINPersonal Identification NumberPRO SMProtected with secure messagingPTSProtocol Transmission SelectionRFUReserved for Future UseRSTReset (of the card)SFIDShort EF IdentifierSMSecure MessagingSW1-SW2Status bytesTSInitial ATR characterVPPProgramming VoltageVUVehicle UnitXXhValue XX in hexadecimal notation‘XXh’Value XX in hexadecimal notation||Concatenation symbol 03||04=0304
 1.2. 
The following references are used in this Appendix:

ISO/IEC 7816-2Identification cards — Integrated circuit cards — Part 2: Dimensions and location of the contacts. ISO/IEC 7816-2:2007.ISO/IEC 7816-3Identification cards — Integrated circuit cards — Part 3: Electrical interface and transmission protocols. ISO/IEC 7816-3:2006.ISO/IEC 7816-4Identification cards — Integrated circuit cards — Part 4: Organization, security and commands for interchange. ISO/IEC 7816-4:2013 + Cor 1: 2014.ISO/IEC 7816-6Identification cards — Integrated circuit cards — Part 6: Interindustry data elements for interchange. ISO/IEC 7816-6:2004 + Cor 1: 2006.ISO/IEC 7816-8Identification cards — Integrated circuit cards — Part 8: Commands for security operations. ISO/IEC 7816-8:2004.ISO/IEC 9797-2Information technology — Security techniques — Message Authentication Codes (MACs) — Part 2: Mechanisms using a dedicated hash-function. ISO/IEC 9797-2:2011
 2.  TCS_01 All electronic signals shall be in accordance with ISO/IEC 7816-3 unless specified otherwise.
 TCS_02 The location and dimensions of the card contacts shall comply with the ISO/IEC 7816-2.
 2.1.  TCS_03 The card shall work according to specifications within the consumption limits specified in ISO/IEC 7816-3.
 TCS_04 
Voltage selection shall be performed according to ISO/IEC 7816-3.
 2.2.  TCS_05 The card shall not require a programming voltage at pin C6. It is expected that pin C6 is not connected in an IFD. Contact C6 may be connected to Vcc in the card but shall not be connected to ground. This voltage should not be interpreted in any case.
 2.3.  TCS_06 The card shall operate within a frequency range of 1 to 5 MHz and may support higher frequencies. Within one card session the clock frequency may vary ± 2 %. The clock frequency is generated by the Vehicle Unit and not the card itself. The duty cycle may vary between 40 and 60 %.
 TCS_07 
Low High  
Bit 3 Bit 2 Bit 1
0 0 1 Clockstop allowed, no preferred level
0 1 1 Clockstop allowed, high level preferred
1 0 1 Clockstop allowed, low level preferred
0 0 0 Clockstop not allowed
0 1 0 Clockstop only allowed on high level
1 0 0 Clockstop only allowed on low level
Bits 4 to 8 are not used.
 2.4.  TCS_08 The I/O contact C7 is used to receive data from and to transmit data to the IFD. During operation only either the card or the IFD shall be in transmit mode. Should both units be in transmit mode no damage shall occur to the card. Unless transmitting, the card shall enter the reception mode.
 2.5.  TCS_09 

 Operation state while executing commands or interfacing with Digital Unit,
 Idle state at all other times; in this state all data shall be retained by the card.
 3.  3.1. 
This paragraph describes the minimum functionality required by Tachograph cards and VUs to ensure correct operation and interoperability.

Tachograph cards are as compliant as possible with the available ISO/IEC applicable norms (especially ISO/IEC 7816). However, commands and protocols are fully described in order to specify some restricted usage or some differences if they exist. The commands specified are fully compliant with the referred norms except where indicated.
 3.2.  TCS_10 The Transmission protocol shall be compliant with ISO/IEC 7816-3 for T = 0 and T = 1. In particular, the VU shall recognise waiting time extensions sent by the card.
 3.2.1  TCS_11 The card shall provide both protocol T=0 and protocol T=1. In addition the card may support further contact-oriented protocols.
 TCS_12 T=0 is the default protocol, a PTS command is therefore necessary to change the protocol to T=1.
 TCS_13 Devices shall support direct convention in both protocols: the direct convention is hence mandatory for the card.
 TCS_14 The Information Field Size Card byte shall be presented at the ATR in character TA3. This value shall be at least ‘F0h’ (=240 bytes).

The following restrictions apply to the protocols:
 TCS_15 

— The interface device shall support an answer on I/O after the rising edge of the signal on RST from 400 cc.
— The interface device shall be able to read characters separated with 12 etu.
— The interface device shall read an erroneous character and its repetition if separated with 13 etu. If an erroneous character is detected, the Error signal on I/O can occur between 1 etu and 2 etu. The device shall support a 1 etu delay.
— The interface device shall accept a 33 bytes ATR (TS+32)
— If TC1 is present in the ATR, the Extra Guard Time shall be present for characters sent by the interface device although characters sent by the card can still be separated with 12 etu. This is also true for the ACK character sent by the card after a P3 character emitted by the interface device.
— The interface device shall take into account a NUL character emitted by the card.
— The interface device shall accept the complementary mode for ACK.
— The get-response command cannot be used in chaining mode to get a data which length could exceed 255 bytes.
 TCS_16 

— NAD byte: not used (NAD shall be set to ‘00’).
— S-block ABORT: not used.
— S-block VPP state error: not used.
— The total chaining length for a data field will not exceed 255 bytes (to be ensured by the IFD).
— The Information Field Size Device (IFSD) shall be indicated by the IFD immediately after the ATR: the IFD shall transmit the S-Block IFS request after the ATR and the card shall send back S-Block IFS. The recommended value for IFSD is 254 bytes.
— The card will not ask for an IFS readjustment.
 3.2.2  TCS_17 
Example of Basic Biprotocol ATR according to ISO/IEC 7816-3

Character Value Remarks
TS ‘3Bh’ Indicates direct convention.
T0 ‘85h’ TD1 present; 5 historical bytes are presents.
TD1 ‘80h’ TD2 present; T=0 to be used
TD2 ‘11h’ TA3 present; T=1 to be used
TA3 ‘XXh’ (at least ‘F0h’) Information Field Size Card ( IFSC)
TH1 to TH5 ‘XXh’ Historical characters
TCK ‘XXh’ Check Character (exclusive OR) TCS_18 After the Answer To Reset (ATR), the Master File (MF) is implicitly selected and becomes the Current Directory.
 3.2.3  TCS_19 The default Protocol is T=0. To set the T=1 protocol, a PTS (also known as PPS) must be sent to the card by the device.
 TCS_20 
The PTS can be used, as indicated in ISO/IEC 7816-3, to switch to higher baud rates than the default one proposed by the card in the ATR if any (TA(1) byte).

Higher baud rates are optional for the card.
 TCS_21 
Examples of basic PTS for protocol selection are the following:

Character Value Remarks
PPSS ‘FFh’ The Initiate Character.
PPS0 ‘00h’ or ‘01h’ PPS1 to PPS3 are not present; ‘00h’ to select T0, ‘01h’ to select T1.
PK ‘XXh’ Check Character‘XXh’ = ‘FFh’ if PPS0 = ‘00h’,
‘XXh’ = ‘FEh’ if PPS0 = ‘01h’. 3.3.  TCS_22 An access rule specifies for an access mode, i.e. command, the corresponding security conditions. If these security conditions are fulfilled the corresponding command is processed.
 TCS_23 
Abbreviation Meaning
ALW The action is always possible and can be executed without any restriction. Command and response APDU are sent in plain text, i.e. without secure messaging.
NEV The action is never possible.
PLAIN-C The command APDU is sent in plain, i.e. without secure messaging.
PWD The action may only be executed if the workshop card PIN has been successfully verified, i.e. if the card internal security status ‘PIN_Verified’ is set. The command must be sent without secure messaging.
EXT-AUT-G1 The action may only be executed if the External Authenticate command for the generation 1 authentication (see also Appendix 11 Part A) has been successfully performed.
SM-MAC-G1 The APDU (command and response) must be applied with generation 1 secure messaging in authentication-only mode (see Appendix 11 Part A).
SM-C-MAC-G1 The command APDU must be applied with generation 1 secure messaging in authentication only mode (see Appendix 11 Part A).
SM-R-ENC-G1 The response APDU must be applied with generation 1 secure messaging in encryption mode (see Appendix 11 Part A), i.e. no message authentication code is returned.
SM-R-ENC-MAC-G1 The response APDU must be applied with generation 1 secure messaging in encrypt-then-authenticate mode (see Appendix 11 Part A).
SM-MAC-G2 The APDU (command and response) must be applied with generation 2 secure messaging in authentication-only mode (see Appendix 11 Part B).
SM-C-MAC-G2 The command APDU must be applied with generation 2 secure messaging in authentication only mode (see Appendix 11 Part B).
SM-R-ENC-MAC-G2 The response APDU must be applied with generation 2 secure messaging in encrypt-then-authenticate mode (see Appendix 11 Part B). TCS_24 

                                          AND
                                       All security conditions must be fulfilled
                                          OR
                                       At least one security condition must be fulfilled

The access rules for the file system, i.e. the SELECT, READ BINARY and UPDATE BINARY command, are specified in chapter 4. The access rules for the remaining commands are specified in the following tables. The term ‘not applicable’ is used if there is no requirement to support the command. In this case the command may or may not be supported, but the access condition is out of scope.
 TCS_25 
Command
                                           
                                             Driver Card
                                           
                                             Workshop Card
                                           
                                             Control Card
                                           
                                             Company Card
                                          

                                             External Authenticate
                                              
 — For generation 1 authentication
 
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          
 — For generation 2 authentication
 
                                             ALW
                                           
                                             PWD
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Internal Authenticate
                                           
                                             ALW
                                           
                                             PWD
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             General Authenticate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Get Challenge
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET AT
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET DST
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Process DSRC Message
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Compute Digital Signature
                                           ALW ORSM-MAC-G2 ALW ORSM-MAC-G2 
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Hash
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                          

                                             PERFORM HASH of FILE
                                           ALW ORSM-MAC-G2 ALW ORSM-MAC-G2 
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Verify Certificate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             PSO: Verify Digital Signature
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                          

                                             Verify
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                           
                                             Not applicable TCS_26 
Command
                                           
                                             Driver Card
                                           
                                             Workshop Card
                                           
                                             Control Card
                                           
                                             Company Card
                                          

                                             External Authenticate
                                              
 — For generation 1 authentication
 
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          
 — For generation 2 authentication
 
                                             ALW
                                           
                                             PWD
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Internal Authenticate
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             General Authenticate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Get Challenge
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET AT
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET DST
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Process DSRC Message
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             Not applicable
                                          

                                             PSO: Compute Digital Signature
                                           ALW ORSM-MAC-G2 ALW ORSM-MAC-G2 
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Hash
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                          

                                             PERFORM HASH of FILE
                                           ALW ORSM-MAC-G2 ALW ORSM-MAC-G2 
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Verify Certificate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             PSO: Verify Digital Signature
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                          

                                             Verify
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                           
                                             Not applicable TCS_27 
Command
                                           
                                             Driver Card
                                           
                                             Workshop Card
                                           
                                             Control Card
                                           
                                             Company Card
                                          

                                             External Authenticate
                                              
 — For generation 1 authentication
 
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          
 — For generation 2 authentication
 
                                             ALW
                                           
                                             PWD
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Internal Authenticate
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             General Authenticate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Get Challenge
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET AT
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             MSE:SET DST
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             Process DSRC Message
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Compute Digital Signature
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Hash
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PERFORM HASH of FILE
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             PSO: Verify Certificate
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                           
                                             ALW
                                          

                                             PSO: Verify Digital Signature
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                           
                                             Not applicable
                                          

                                             Verify
                                           
                                             Not applicable
                                           
                                             ALW
                                           
                                             Not applicable
                                           
                                             Not applicable TCS_28 Note: The command descriptions provide more information on the support of the commands for the different tachograph card types and the different DFs. 3.4. 
Commands and file organisation are deduced from and complies with ISO/IEC 7816-4.

This section describes the following APDU command-response pairs. The command variants which are supported by a generation 1 and 2 application are specified in the corresponding command descriptions.


Command INS
SELECT ‘A4h’
READ BINARY ‘B0h’, ‘B1h’
UPDATE BINARY ‘D6h’, ‘D7h’
GET CHALLENGE ‘84h’
VERIFY ‘20h’
GET RESPONSE ‘C0h’
PERFORM SECURITY OPERATION ‘2Ah’
 — VERIFY CERTIFICATE
 
 — COMPUTE DIGITAL SIGNATURE
 
 — VERIFY DIGITAL SIGNATURE
 
 — HASH
 
 — PERFORM HASH OF FILE
 
 — PROCESS DSRC MESSAGE
 
INTERNAL AUTHENTICATE ‘88h’
EXTERNAL AUTHENTICATE ‘82h’
MANAGE SECURITY ENVIRONMENT ‘22h’
 — SET DIGITAL SIGNATURE TEMPLATE
 
 — SET AUTHENTICATION TEMPLATE
 
GENERAL AUTHENTICATE ‘86h’
 TCS_29 

                                             SW1
                                           
                                             SW2
                                           
                                             Meaning
                                          

                                             90
                                           
                                             00
                                           
                                             Normal processing.
                                          

                                             61
                                           
                                             XX
                                           
                                             Normal processing. XX = number of response bytes available.
                                          

                                             62
                                           
                                             81
                                           
                                             Warning processing. Part of returned data may be corrupted
                                          

                                             63
                                           
                                             00
                                           
                                             Authentication failed (Warning)
                                          

                                             63
                                           
                                             CX
                                           
                                             Wrong CHV (PIN). Remaining attempts counter provided by 
                                             ‘
                                             X
                                             ’
                                             .
                                          

                                             64
                                           
                                             00
                                           
                                             Execution error - State of non-volatile memory unchanged. Integrity error.
                                          

                                             65
                                           
                                             00
                                           
                                             Execution error - State of non-volatile memory changed
                                          

                                             65
                                           
                                             81
                                           
                                             Execution error - State of non-volatile memory changed – Memory failure
                                          

                                             66
                                           
                                             88
                                           
                                                      Security error
                                                   wrong cryptographic checksum (during Secure Messaging) or
wrong certificate (during certificate verification) or
wrong cryptogram (during external authentication) or
wrong signature (during signature verification)

                                             67
                                           
                                             00
                                           
                                             Wrong length (wrong Lc or Le)
                                          

                                             68
                                           
                                             83
                                           
                                             Last command of the chain expected
                                          

                                             69
                                           
                                             00
                                           
                                             Forbidden command (no response available in T=0)
                                          

                                             69
                                           
                                             82
                                           
                                             Security status not satisfied.
                                          

                                             69
                                           
                                             83
                                           
                                             Authentication method blocked.
                                          

                                             69
                                           
                                             85
                                           
                                             Conditions of use not satisfied.
                                          

                                             69
                                           
                                             86
                                           
                                             Command not allowed (no current EF).
                                          

                                             69
                                           
                                             87
                                           
                                             Expected Secure Messaging Data Objects missing
                                          

                                             69
                                           
                                             88
                                           
                                             Incorrect Secure Messaging Data Objects
                                          

                                             6A
                                           
                                             80
                                           
                                             Incorrect parameters in data field
                                          

                                             6A
                                           
                                             82
                                           
                                             File not found.
                                          

                                             6A
                                           
                                             86
                                           
                                             Wrong parameters P1-P2.
                                          

                                             6A
                                           
                                             88
                                           
                                             Referenced data not found.
                                          

                                             6B
                                           
                                             00
                                           
                                             Wrong parameters (offset outside the EF).
                                          

                                             6C
                                           
                                             XX
                                           
                                             Wrong length, SW2 indicates the exact length. No data field is returned.
                                          

                                             6D
                                           
                                             00
                                           
                                             Instruction code not supported or invalid.
                                          

                                             6E
                                           
                                             00
                                           
                                             Class not supported.
                                          

                                             6F
                                           
                                             00
                                            — Other checking errors

Additional status words as defined in ISO/IEC 7816-4 can be returned, if their behaviour is not explicitly mentioned in this appendix.

For example the following status words can be optionally returned:

6881: Logical channel not supported

6882: Secure messaging not supported
 TCS_30 If more than one error condition is fulfilled in one command APDU the card may return any of the appropriate status words.
 3.5. 
The mandatory commands for the Tachograph cards are described in this chapter.

Additional relevant details, related to cryptographic operations involved, are given in Appendix 11 Common security mechanisms for Tachograph Generation 1 and Generation 2.

All commands are described independently of the used protocol (T=0 or T=1). The APDU bytes CLA, INS, P1, P2, Lc and Le are always indicated. If Lc or Le is not needed for the described command, the associated length, value and description are empty.
 TCS_31 If both length bytes (Lc and Le) are requested, the described command has to be split in two parts if the IFD is using protocol T=0: the IFD sends the command as described with P3=Lc + data and then sends a GET RESPONSE (see § 3.5.6) command with P3=Le.
 TCS_32 

— When using protocol T=1, the card shall answer to Le=0 by sending all available output data.
— When using protocol T=0, the IFD shall send the first command with P3=Lc + data, the card shall answer (to this implicit Le=0) by the Status bytes ‘61La’, where La is the number of response bytes available. The IFD shall then generate a GET RESPONSE command with P3 = La to read the data.
 TCS_33 

— Indicate the extended length field support in the ATR
— Provide the supported buffer sizes by means of the extended length information in the EF ATR/INFO see TCS_146.
— Indicate whether it supports extended length fields for T = 1 and / or T = 0 in the EF Extended Length, see TCS_147.
— Support extended length fields for the tachograph application generation 1 and 2.
All commands are specified for short length fields. The usage of extended length APDUs is clear from ISO/IEC 7816-4.In general the commands are specified for the plain mode, i.e. without secure messaging, as the secure messaging layer is specified in Appendix 11. It is clear from the access rules for a command whether the command shall support secure messaging or not and whether the command shall support generation 1 and / or generation 2 secure messaging. Some command variants are described with secure messaging to illustrate the usage of secure messaging. TCS_34 The VU shall perform the complete generation 2 VU — card mutual authentication protocol for a session including the certificate verification (if required) either in the DF Tachograph, the DF Tachograph_G2 or the MF.
 3.5.1 
This command is compliant with ISO/IEC 7816-4, but has a restricted usage compared to the command defined in the norm.

The SELECT command is used:


— to select an application DF (selection by name must be used)
— to select an elementary file corresponding to the submitted file ID
 3.5.1.1 
This command allows selecting an application DF in the card.
 TCS_35 This command can be performed from anywhere in the file structure (after the ATR or at any time).
 TCS_36 The selection of an application resets the current security environment. After performing the application selection, no current public key is selected anymore. The EXT-AUT-G1 access condition is also lost. If the command was performed without secure messaging, the former secure messaging session keys are no longer available.
 TCS_37 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘A4h’ 
P1 1 ‘04h’ Selection by name (AID)
P2 1 ‘0Ch’ No response expected
Lc 1 ‘NNh’ Number of bytes sent to the card (length of the AID):‘06h’ for the Tachograph application
#6-#(5+NN) NN ‘XX..XXh’ AID: ‘FF 54 41 43 48 4F’ for the Generation 1 tachograph applicationAID: ‘FF 53 4D 52 44 54’ for the Generation 2 tachograph application
No response to the SELECT command is needed (Le absent in T=1, or no response asked in T=0).
 TCS_38 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the application corresponding with the AID is not found, the processing state returned is ‘6A82’.
— In T=1, if the byte Le is present, the state returned is ‘6700’.
— In T=0, if a response is asked after the SELECT command, the state returned is ‘6900’.
— If the selected application is considered to be corrupted (integrity error is detected within the file attributes), the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
 3.5.1.2  TCS_39 Command Message
 TCS_40 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘A4h’ 
P1 1 ‘02h’ Selection of an EF under the current DF
P2 1 ‘0Ch’ No response expected
Lc 1 ‘02h’ Number of bytes sent to the card
#6-#7 2 ‘XXXXh’ File Identifier
No response to the SELECT command is needed (Le absent in T=1, or no response asked in T=0).
 TCS_41 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the file corresponding with the file identifier is not found, the processing state returned is ‘6A82’.
— In T=1, if the byte Le is present, the state returned is ‘6700’.
— In T=0, if a response is asked after the SELECT command, the state returned is ‘6900’.
— If the selected file is considered to be corrupted (integrity error is detected within the file attributes), the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
 3.5.2 
This command is compliant with ISO/IEC 7816-4, but has a restricted usage compared to the command defined in the norm.

The READ BINARY command is used to read data from a transparent file.

The response of the card consists of returning the data read, optionally encapsulated in a secure messaging structure.
 3.5.2.1 
This command enables the IFD to read data from the EF currently selected, without secure messaging.
Note: This command without secure messaging can only be used to read a file that supports the ALW security condition for the Read access mode. TCS_42 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘B0h’ Read Binary
P1 1 ‘XXh’ Offset in bytes from the beginning of the file: Most Significant Byte
P2 1 ‘XXh’ Offset in bytes from the beginning of the file: Least Significant Byte
Le 1 ‘XXh’ Length of data expected. Number of Bytes to be read.Note: bit 8 of P1 must be set to 0. TCS_43 
Byte Length Value Description
#1-#X X ‘XX..XXh’ Data read
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no EF is selected, the processing state returned is ‘6986’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be read is not compatible with the size of the EF (Offset + Le > EF size) the processing state returned is ‘6700’ or ‘6Cxx’ where ‘xx’ indicates the exact length.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
— If an integrity error is detected within the stored data, the card shall return the demanded data, and the processing state returned is ‘6281’.
 3.5.2.1.1 
This command enables the IFD to read data from the EF currently selected with secure messaging, in order to verify the integrity of the data received and to protect the confidentiality of the data if the security condition SM-R-ENC-MAC-G1 (generation 1) or SM-R-ENC-MAC-G2 (generation 2) is applied.
 TCS_44 
Byte Length Value Description
CLA 1 ‘0Ch’ Secure Messaging asked
INS 1 ‘B0h’ Read Binary
P1 1 ‘XXh’ P1 ( offset in bytes from the beginning of the file): Most Significant Byte
P2 1 ‘XXh’ P2 ( offset in bytes from the beginning of the file): Least Significant Byte
Lc 1 ‘XXh’ Length of input data for secure messaging
#6 1 ‘97h’ TLE: Tag for expected length specification.
#7 1 ‘01h’ LLE: Length of expected length
#8 1 ‘NNh’ Expected length specification (original Le): Number of Bytes to be read
#9 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#10 1 ‘XXh’ LCC: Length of following cryptographic checksum
 ‘04h’ for Generation 1 secure messaging (see Appendix 11 Part A)
 ‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#11-#(10+L) L ‘XX..XXh’ Cryptographic checksum
Le 1 ‘00h’ As specified in ISO/IEC 7816-4 TCS_45 
Byte
                                                    
                                                      Length
                                                    
                                                      Value
                                                    
                                                      Description
                                                   

                                                      #1
                                                    
                                                      1
                                                    
                                                      ‘
                                                      81h
                                                      ’
                                                    
                                                      T
                                                      
                                                         PV
                                                      
                                                      : Tag for plain value data
                                                   

                                                      #2
                                                    
                                                      L
                                                    ‘NNh’ or‘81 NNh’ L
                                                               PV
                                                            : length of returned data (=original Le).L is 2 bytes if L
                                                               PV
                                                            >127 bytes.

                                                      #(2+L) - #(1+L+NN)
                                                    
                                                      NN
                                                    
                                                      ‘
                                                      XX..XXh
                                                      ’
                                                    
                                                      Plain Data value
                                                   

                                                      #(2+L+NN)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      99h
                                                      ’
                                                    
                                                      Tag for Processing Status (SW1-SW2) – optional for generation 1 secure messaging
                                                   

                                                      #(3+L+NN)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      02h
                                                      ’
                                                    
                                                      Length of Processing Status – optional for generation 1 secure messaging
                                                   

                                                      #(4+L+NN) - #(5+L+NN)
                                                    
                                                      2
                                                    
                                                      ‘
                                                      XX XXh
                                                      ’
                                                    
                                                      Processing Status of the unprotected response APDU – optional for generation 1 secure messaging
                                                   

                                                      #(6+L+NN)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      8Eh
                                                      ’
                                                    
                                                      TCC: Tag for cryptographic checksum
                                                   

                                                      #(7+L+NN)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      XXh
                                                      ’
                                                    LCC: Length of following cryptographic checksum
 ‘04h’ for Generation 1 secure messaging (see Appendix 11 Part A)
 ‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)

                                                      #(8+L+NN)-#(7+M+L+NN)
                                                    
                                                      M
                                                    
                                                      ‘
                                                      XX..XXh
                                                      ’
                                                    
                                                      Cryptographic checksum
                                                   

                                                      SW
                                                    
                                                      2
                                                    
                                                      ‘
                                                      XXXXh
                                                      ’
                                                    
                                                      Status Words (SW1,SW2) TCS_46 
Byte
                                                    
                                                      Length
                                                    
                                                      Value
                                                    
                                                      Description
                                                   

                                                      #1
                                                    
                                                      1
                                                    
                                                      ‘
                                                      87h
                                                      ’
                                                    
                                                      T
                                                      
                                                         PI CG
                                                      
                                                      : Tag for encrypted data (cryptogram)
                                                   

                                                      #2
                                                    
                                                      L
                                                    ‘MMh’ or‘81 MMh’ L
                                                               PI CG
                                                            : length of returned encrypted data (different of original Le of the command due to padding).L is 2 bytes if LPI CG > 127 bytes.

                                                      #(2+L)-#(1+L+MM)
                                                    
                                                      MM
                                                    
                                                      ‘
                                                      01XX..XXh
                                                      ’
                                                    
                                                      Encrypted Data: Padding Indicator and cryptogram
                                                   

                                                      #(2+L+MM)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      99h
                                                      ’
                                                    
                                                      Tag for Processing Status (SW1-SW2) – optional for generation 1 secure messaging
                                                   

                                                      #(3+L+MM)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      02h
                                                      ’
                                                    
                                                      Length of Processing Status – optional for generation 1 secure messaging
                                                   

                                                      #(4+L+MM) - #(5+L+MM)
                                                    
                                                      2
                                                    
                                                      ‘
                                                      XX XXh
                                                      ’
                                                    
                                                      Processing Status of the unprotected response APDU – optional for generation 1 secure messaging
                                                   

                                                      #(6+L+MM)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      8Eh
                                                      ’
                                                    
                                                      TCC: Tag for cryptographic checksum
                                                   

                                                      #(7+L+MM)
                                                    
                                                      1
                                                    
                                                      ‘
                                                      XXh
                                                      ’
                                                    LCC: Length of following cryptographic checksum
 ‘04h’ for Generation 1 secure messaging (see Appendix 11 Part A)
 ‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)

                                                      #(8+L+MM)-#(7+N+L+MM)
                                                    
                                                      N
                                                    
                                                      ‘
                                                      XX..XXh
                                                      ’
                                                    
                                                      Cryptographic checksum
                                                   

                                                      SW
                                                    
                                                      2
                                                    
                                                      ‘
                                                      XXXXh
                                                      ’
                                                    
                                                      Status Words (SW1,SW2)
The READ BINARY command may return regular processing states listed in TCS_43 under Tag ‘99h’ as described in TCS_59 using the secure messaging response structure.

Additionally, some errors specifically related to secure messaging can happen. In that case, the processing state is simply returned, with no secure messaging structure involved:
 TCS_47 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If no current session key is available, the processing state ‘6A88’ is returned. It happens either if the session key has not already been generated or if the session key validity has expired (in this case the IFD must re-run a mutual authentication process to set a new session key).
— If some expected data objects (as specified above) are missing in the secure messaging format, the processing state ‘6987’ is returned: this error happens if an expected tag is missing or if the command body is not properly constructed.
— If some data objects are incorrect, the processing state returned is ‘6988’: this error happens if all the required tags are present but some lengths are different from the ones expected.
— If the verification of the cryptographic checksum fails, the processing state returned is ‘6688’.
 3.5.2.2 
This command variant enables the IFD to select an EF by means of a short EF identifier and read data from this EF.
 TCS_48 A tachograph card shall support this command variant for all Elementary Files with a specified short EF identifier. These short EF identifiers are specified in chapter 4.
 TCS_49 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘B0h’ Read Binary
P1 1 ‘XXh’ Bit 8 is set to 1Bit 7 and 6 are set to 00Bit 5 — 1 encode the short EF identifier of the corresponding EF
P2 1 ‘XXh’ Encodes an offset from 0 to 255 bytes in the EF referenced by P1
Le 1 ‘XXh’ Length of data expected. Number of Bytes to be read.Note: The short EF identifiers used for the Generation 2 tachograph application are specified in chapter 4.
If P1 encodes a short EF identifier and the command is successful, the identified EF becomes the currently selected EF (current EF).
 TCS_50 
Byte Length Value Description
#1-#L L ‘XX..XXh’ Data read
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the file corresponding with the short EF identifier is not found, the processing state returned is ‘6A82’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be read is not compatible with the size of the EF (Offset + Le > EF size) the processing state returned is ‘6700’ or ‘6Cxx’ where ‘xx’ indicates the exact length.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
— If an integrity error is detected within the stored data, the card shall return the demanded data, and the processing state returned is ‘6281’.
 3.5.2.3 
This command variant enables the IFD to read data from an EF with 32 768 bytes or more.
 TCS_51 A tachograph card which supports EFs with 32 768 bytes or more shall support this command variant for these EFs. A tachograph card may or may not support this command variant for other EFs with the exception of the EF Sensor_Installation_Data see TCS_156 and TCS_160.
 TCS_52 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘B1h’ Read Binary
P1 1 ‘00h’ Current EF
P2 1 ‘00h’
Lc 1 ‘NNh’ Lc Length of offset data object.
#6-#(5+NN) NN ‘XX..XXh’ Offset data object:Tag‘54h’Length‘01h’ or ‘02h’Valueoffset
Le
                                                 
                                                   1
                                                 
                                                   'XXh'
                                                 
                                                   As specified in ISO/IEC 7816-4
The IFD shall encode the offset data object's length with a minimum possible number of octets, i.e. using the length byte ‘01h’ the IFD shall encode an offset from 0 to 255 and using the length byte ‘02h’ an offset from ‘256’ up to ‘65 535’ bytes.

In case of T = 0 the card assumes the value Le = ‘00h’ if no secure messaging is applied.

In case of T = 1 the processing state returned is ‘6700’ if Le=‘01h’.
 TCS_53 
Byte Length Value Description
#1-#L L ‘XX..XXh’ Data read encapsulated in a discretionary data object with tag ‘53h’.
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no EF is selected, the processing state returned is ‘6986’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be read is not compatible with the size of the EF (Offset + Le > EF size) the processing state returned is ‘6700’ or ‘6Cxx’ where ‘xx’ indicates the exact length.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
— If an integrity error is detected within the stored data, the card shall return the demanded data, and the processing state returned is ‘6281’.
 3.5.2.3.1 
The following example illustrates the usage of secure messaging if the security condition SM-MAC-G2 applies.
 TCS_54 
Byte Length Value Description
CLA 1 ‘0Ch’ Secure Messaging asked
INS 1 ‘B1h’ Read Binary
P1 1 ‘00h’ Current EF
P2 1 ‘00h’
Lc 1 ‘XXh’ Length of the secured data field
#6 1 ‘B3h’ Tag for plain value data encoded in BER-TLV
#7 1 ‘NNh’ LPV: length of transmitted data
#(8)-#(7+NN) NN ‘XX..XXh’ Plain Data encoded in BER-TLV, i.e. the offset data object with tag ‘54’
#(8+NN) 1 ‘97h’ TLE: Tag for expected length specification.
#(9+NN) 1 ‘01h’ LLE: Length of expected length
#(10+NN) 1 ‘XXh’ Expected length specification (original Le): Number of bytes to be read
#(11+NN) 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#(12+NN) 1 ‘XXh’ LCC: Length of following cryptographic checksum‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#(13+NN)-#(12+M+NN) M ‘XX..XXh’ Cryptographic checksum
Le 1 ‘00h’ As specified in ISO/IEC 7816-4 TCS_55 
Byte Length Value Description
#1 1 ‘B3h’ Plain Data encoded in BER-TLV
#2 L ‘NNh’ or‘81 NNh’ LPV: length of returned data (=original Le).L is 2 bytes if LPV>127 bytes.
#(2+L)-#(1+L+NN) NN ‘XX..XXh’ Plain Data value encoded in BER-TLV, i.e. data read encapsulated in a discretionary data object with tag ‘53h’.
#(2+L+NN) 1 ‘99h’ Processing Status of the unprotected response APDU
#(3+L+NN) 1 ‘02h’ Length of Processing Status
#(4+L+NN) — #(5+L+NN) 2 ‘XX XXh’ Processing Status of the unprotected response APDU
#(6+L+NN) 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#(7+L+NN) 1 ‘XXh’ LCC: Length of following cryptographic checksum‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#(8+L+NN)-#(7+M+L+NN) M ‘XX..XXh’ Cryptographic checksum
SW 2 ‘XXXXh’ Status Words (SW1,SW2) 3.5.3 
This command is compliant with ISO/IEC 7816-4, but has a restricted usage compared to the command defined in the norm.

The UPDATE BINARY command message initiates the update (erase + write) of the bits already present in an EF binary with the bits given in the command APDU.
 3.5.3.1 
This command enables the IFD to write data into the EF currently selected, without the card verifying the integrity of data received.
Note: This command without secure messaging can only be used to update a file that supports the ALW security condition for the Update access mode. TCS_56 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘D6h’ Update Binary
P1 1 ‘XXh’ Offset in bytes from the beginning of the file: Most Significant Byte
P2 1 ‘XXh’ Offset in bytes from the beginning of the file: Least Significant Byte
Lc 1 ‘NNh’ Lc Length of data to Update. Number of bytes to be written.
#6-#(5+NN) NN ‘XX..XXh’ Data to be writtenNote: bit 8 of P1 must be set to 0. TCS_57 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no EF is selected, the processing state returned is ‘6986’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be written is not compatible with the size of the EF (Offset + Lc > EF size) the processing state returned is ‘6700’.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘6400’ or ‘6500’.
— If writing is unsuccessful, the processing state returned is ‘6581’.
 3.5.3.1.1 
This command enables the IFD to write data into the EF currently selected, with the card verifying the integrity of data received. As no confidentiality is required, the data are not encrypted.
 TCS_58 
Byte Length Value Description
CLA 1 ‘0Ch’ Secure Messaging asked
INS 1 ‘D6h’ Update Binary
P1 1 ‘XXh’ Offset in bytes from the beginning of the file:Most Significant Byte
P2 1 ‘XXh’ Offset in bytes from the beginning of the file:Least Significant Byte
Lc 1 ‘XXh’ Length of the secured data field
#6 1 ‘81h’ TPV: Tag for plain value data
#7 L ‘NNh’ or‘81 NNh’ LPV: length of transmitted data.L is 2 bytes if LPV > 127 bytes.
#(7+L)-#(6+L+NN) NN ‘XX..XXh’ Plain Data value (Data to be written)
#(7+L+NN) 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#(8+L+NN) 1 ‘XXh’ LCC: Length of following cryptographic checksum‘04h’ for Generation 1 secure messaging (see Appendix 11 Part A)‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#(9+L+NN)-#(8+M+L+NN) M ‘XX..XXh’ Cryptographic checksum
Le 1 ‘00h’ As specified in ISO/IEC 7816-4 TCS_59 
Byte Length Value Description
#1 1 ‘99h’ TSW: Tag for Status Words (to be protected by CC)
#2 1 ‘02h’ LSW: length of returned Status Words
#3-#4 2 ‘XXXXh’ Processing Status of the unprotected response APDU
#5 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#6 1 ‘XXh’ LCC: Length of following cryptographic checksum
 ‘04h’ for Generation 1 secure messaging (see Appendix 11 Part A)
 ‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#7-#(6+L) L ‘XX..XXh’ Cryptographic checksum
SW 2 ‘XXXXh’ Status Words (SW1,SW2)
The ‘regular’ processing states, described for the UPDATE BINARY command with no secure messaging (see §3.5.3.1), can be returned using the response message structure described above.

Additionally, some errors specifically related to secure messaging can happen. In that case, the processing state is simply returned, with no secure messaging structure involved:
 TCS_60 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If no current session key is available, the processing state ‘6A88’ is returned.
— If some expected data objects (as specified above) are missing in the secure messaging format, the processing state ‘6987’ is returned: this error happens if an expected tag is missing or if the command body is not properly constructed.
— If some data objects are incorrect, the processing state returned is ‘6988’: this error happens if all the required tags are present but some lengths are different from the ones expected.
— If the verification of the cryptographic checksum fails, the processing state returned is ‘6688’.
 3.5.3.2 
This command variant enables the IFD to select an EF by means of a short EF identifier and write data from this EF.
 TCS_61 A tachograph card shall support this command variant for all Elementary Files with a specified short EF identifier. These short EF identifiers are specified in chapter 4.
 TCS_62 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘D6h’ Update Binary
P1 1 ‘XXh’ Bit 8 is set to 1Bit 7 and 6 are set to 00Bit 5 — 1 encode the short EF identifier of the corresponding EF
P2 1 ‘XXh’ Encodes an offset from 0 to 255 bytes in the EF referenced by P1
Lc 1 ‘NNh’ Lc Length of data to Update. Number of bytes to be written.
#6-#(5+NN) NN ‘XX..XXh’ Data to be written TCS_63 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)Note: The short EF identifiers used for the generation 2 tachograph application are specified in chapter 4.
If P1 encodes a short EF identifier and the command is successful, the identified EF becomes the currently selected EF (current EF).


— If the command is successful, the card returns ‘9000’.
— If the file corresponding with the short EF identifier is not found, the processing state returned is ‘6A82’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be written is not compatible with the size of the EF (Offset + Lc > EF size) the processing state returned is ‘6700’.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘
                                                      6400
                                                   ’ or ‘
                                                      6500
                                                   ’.
— If writing is unsuccessful, the processing state returned is ‘6581’.
 3.5.3.3 
This command variant enables the IFD to write data to an EF with 32 768 bytes or more.
 TCS_64 A tachograph card which supports EFs with 32 768 bytes or more shall support this command variant for these EFs. A tachograph card may or may not support this command variant for other EFs.
 TCS_65 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘D7h’ Update Binary
P1 1 ‘00h’ Current EF
P2 1 ‘00h’
Lc 1 ‘NNh’ Lc Length of data in the command data field
#6-#(5+NN) NN ‘XX..XXh’ Offset data object with tag ‘54h’ || Discretionary data object with tag ‘53h’ that encapsulates the data to be written
The IFD shall encode the offset data object's and the discretionary data object's length with the minimum possible number of octets, i.e. using the length byte ‘01h’ the IFD shall encode an offset / length from 0 to 255 and using the length byte ‘02h’ an offset / length from ‘256’ up to ‘65 535’ bytes.
 TCS_66 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no EF is selected, the processing state returned is ‘6986’.
— If the security conditions of the selected file are not satisfied, the command is interrupted with ‘6982’.
— If the Offset is not compatible with the size of the EF (Offset > EF size), the processing state returned is ‘6B00’.
— If the size of the data to be written is not compatible with the size of the EF (Offset + Lc > EF size) the processing state returned is ‘6700’.
— If an integrity error is detected within the file attributes, the card shall consider the file as corrupted and unrecoverable, the processing state returned is ‘6400’ or ‘6500’.
— If writing is unsuccessful, the processing state returned is ‘6581’.
 3.5.3.3.1 
The following example illustrates the usage of secure messaging if the security condition SM-MAC-G2 applies.
 TCS_67 
Byte Length Value Description
CLA 1 ‘0Ch’ Secure Messaging asked
INS 1 ‘D7h’ Update Binary
P1 1 ‘00h’ Current EF
P2 1 ‘00h’
Lc 1 ‘XXh’ Length of the secured data field
#6 1 ‘B3h’ Tag for plain value data encoded in BER-TLV
#7 L ‘NNh’ or‘81 NNh’ LPV: length of transmitted data.L is 2 bytes if LPV > 127 bytes.
#(7+L)-#(6+L+NN) NN ‘XX..XXh’ Plain Data encoded in BER-TLV, i.e. offset data object with tag ‘54h’ || Discretionary data object with tag ‘53h’ that encapsulates the data to be written
#(7+L+NN) 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#(8+L+NN) 1 ‘XXh’ LCC: Length of following cryptographic checksum‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#(9+L+NN)-#(8+M+L+NN) M ‘XX..XXh’ Cryptographic checksum
Le 1 ‘00h’ As specified in ISO/IEC 7816-4 TCS_68 
Byte Length Value Description
#1 1 ‘99h’ TSW: Tag for Status Words (to be protected by CC)
#2 1 ‘02h’ LSW: length of returned Status Words
#3-#4 2 ‘XXXXh’ Processing Status of the unprotected response APDU
#5 1 ‘8Eh’ TCC: Tag for cryptographic checksum
#6 1 ‘XXh’ LCC: Length of following cryptographic checksum‘08h’, ‘0Ch’ or ‘10h’ depending on AES key length for Generation 2 secure messaging (see Appendix 11 Part B)
#7-#(6+L) L ‘XX..XXh’ Cryptographic checksum
SW 2 ‘XXXXh’ Status Words (SW1,SW2) 3.5.4 
This command is compliant with ISO/IEC 7816-4, but has a restricted usage compared to the command defined in the norm.

The GET CHALLENGE command asks the card to issue a challenge in order to use it in a security related procedure in which a cryptogram or some ciphered data are sent to the card.
 TCS_69 The Challenge issued by the card is only valid for the next command, which uses a challenge, sent to the card.
 TCS_70 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘84h’ INS
P1 1 ‘00h’ P1
P2 1 ‘00h’ P2
Le 1 ‘08h’ Le (Length of Challenge expected). TCS_71 
Byte Length Value Description
#1-#8 8 ‘XX..XXh’ Challenge
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If Le is different from ‘08h’, the processing state is ‘6700’.
— If parameters P1-P2 are incorrect, the processing state is ‘6A86’.
 3.5.5 
This command is compliant with ISO/IEC 7816-4, but has a restricted usage compared to the command defined in the norm.

Only the workshop card is required to support this command.

Other types of tachograph cards may or may not implement this command, but for these cards no reference CHV is personalized. Therefore these cards cannot perform this commend successfully. For other types of tachograph cards than workshop cards the behavior, i.e. the error code returned, is out of the scope of this specification, if this command is sent.

The Verify command initiates the comparison in the card of the CHV (PIN) data sent from the command with the reference CHV stored in the card.
 TCS_72 The PIN entered by the user must be ASCII encoded and right padded with ‘FFh’ bytes up to a length of 8 bytes by the IFD, see also the data type WorkshopCardPIN in Appendix 1.
 TCS_73 The tachograph applications generation 1 and 2 shall use the same reference CHV.
 TCS_74 The tachograph card shall check whether the command is encoded correctly. If the command is not encoded correctly the card shall not compare the CHV values, not decrement the remaining CHV attempt counter and not reset the security status ‘PIN_Verified’, but abort the command. A command is encoded correctly, if the CLA, INS, P1, P2, Lc bytes have the specified values, Le is absent, and the command data field has the correct length.
 TCS_75 Note: Using the same reference CHV and a global security status prevents that a workshop employee must re-enter the PIN after a selection of another tachograph application DF. TCS_76 An unsuccessful comparison is recorded in the card, i.e. the remaining CHV attempts counter shall be decremented by one, in order to limit the number of further attempts of the use of the reference CHV.
 TCS_77 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘20h’ INS
P1 1 ‘00h’ P1
P2 1 ‘00h’ P2 (the verified CHV is implicitly known)
Lc 1 ‘08h’ Length of CHV code transmitted
#6-#13 8 ‘XX..XXh’ CHV TCS_78 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the reference CHV is not found, the processing state returned is ‘6A88’.
— If the CHV is blocked, (the remaining attempt counter of the CHV is null), the processing state returned is ‘6983’. Once in that state, the CHV can never be successfully presented anymore.
— If the comparison is unsuccessful, the remaining attempt Counter is decreased and the status ‘63CX’ is returned (X>0 and X equals the remaining CHV attempts counter.
— If the reference CHV is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.
— If Lc is different from ‘08h’, the processing state is ‘6700’.
 3.5.6 
This command is compliant with ISO/IEC 7816-4.

This command (only necessary and available for T=0 Protocol) is used to transmit prepared data from the card to the interface device (case where a command had included both Lc and Le).

The GET RESPONSE command has to be issued immediately after the command preparing the data, otherwise, the data are lost. After the execution of the GET RESPONSE command (except if the error ‘61xx’ or ‘6Cxx’ occur, see below), the previously prepared data are no longer available.
 TCS_79 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘C0h’ 
P1 1 ‘00h’ 
P2 1 ‘00h’ 
Le 1 ‘XXh’ Number of bytes expected TCS_80 
Byte Length Value Description
#1-#X X ‘XX..XXh’ Data
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no data have been prepared by the card, the processing state returned is ‘6900’ or ‘6F00’.
— If Le exceeds the number of available bytes or if Le is null, the processing state returned is ‘6Cxx’, where xx denotes the exact number of available bytes. In that case, the prepared data are still available for a subsequent GET RESPONSE command.
— If Le is not null and is smaller than the number of available bytes, the required data are sent normally by the card, and the processing state returned is ‘61xx’, where ‘xx’ indicates a number of extra bytes still available by a subsequent GET RESPONSE command.
— If the command is not supported (protocol T=1), the card returns ‘6D00’.
 3.5.7 
This command is compliant with ISO/IEC 7816-8, but has a restricted usage compared to the command defined in the norm.

The VERIFY CERTIFICATE command is used by the card to obtain a Public Key from the outside and to check its validity.
 3.5.7.1  TCS_81 This command variant is only supported by a generation 1 tachograph application.
 TCS_82 When a VERIFY CERTIFICATE command is successful, the Public Key is stored for a future use in the Security environment. This key shall be explicitly set for the use in security related commands (INTERNAL AUTHENTICATE, EXTERNAL AUTHENTICATE or VERIFY CERTIFICATE) by the MSE command (see § 3.5.11) using its key identifier.
 TCS_83 In any case, the VERIFY CERTIFICATE command uses the public key previously selected by the MSE command to open the certificate. This public key must be the one of a Member State or of Europe.
 TCS_84 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘2Ah’ Perform Security Operation
P1 1 ‘00h’ P1
P2 1 ‘AEh’ P2: non BER-TLV coded data (concatenation of data elements)
Lc 1 ‘C2h’ Lc: Length of the certificate, 194 bytes
#6-#199 194 ‘XX..XXh’ Certificate: concatenation of data elements (as described in Appendix 11) TCS_85 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the certificate verification fails, the processing state returned is ‘6688’. The verification and unwrapping process of the certificate is described in Appendix 11 for G1 and G2.
— If no Public Key is present in the Security Environment, ‘6A88’ is returned.
— If the selected public key (used to unwrap the certificate) is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.
— Generation 1 only: If the selected public key (used to unwrap the certificate) has a CHA.LSB () different from ‘00’ (i.e. is not the one of a Member State or of Europe), the processing state returned is ‘6985’.
 3.5.7.2 
Depending on the curve size ECC certificates may be so long that they cannot be transmitted in a single APDU. In this case command chaining according to ISO/IEC 7816-4 must be applied and the certificate transmitted in two consecutive PSO: Verify Certificate APDUs.

The certificate structure and the domain parameters are defined in Appendix 11.
 TCS_86 The command can be performed in the MF, DF Tachograph and DF Tachograph_G2, see also TCS_33.
 TCS_87 
Byte Length Value Description
CLA 1 ‘X0h’ CLA byte indicating command chaining:
 ‘00h’ the only or last command of the chain
 ‘10h’ not the last command of a chain
INS 1 ‘2Ah’ Perform Security Operation
P1 1 ‘00h’ 
P2 1 ‘BEh’ Verify self-descriptive certificate
Lc 1 ‘XXh’ Length of the command data field, see TCS_88 and TCS_89.
#6-#5+L L ‘XX..XXh’ DER-TLV encoded data: ECC Certificate Body data object as first data object concatenated with the ECC Certificate Signature data object as second data object or a part of this concatenation. The tag ‘7F21’ and the corresponding length shall not be transmitted.The order of these data objects is fixed. TCS_88 For short length APDUs the following provisions apply: The IFD shall use the minimum number of APDUs required to transmit the command payload and transmit the maximum number of bytes in the first command APDU according to the value of the Information Field Size Card Byte, see TCS_14. If the IFD behaves differently, the behavior of the card is out of scope.
 TCS_89 Note: According to Appendix 11 the card stores the certificate or the relevant contents of the certificate and updates its currentAuthenticatedTime.
The response message structure and status words are as defined in TCS_85.
 TCS_90 

— If the selected public key (used to unwrap the certificate) has a CHA.LSB (CertificateHolderAuthorisation.equipmentType) that is not suitable for the certificate verification according to Appendix 11, the processing state returned is ‘6985’.
— If the currentAuthenticatedTime of the card is later than the Certificate Expiration Date, the processing state returned is ‘6985’.
— If the last command of the chain is expected, the card returns ‘6883’.
— If incorrect parameters are sent in the command data field, the card returns ‘6A80’ (also used in case the data objects are not sent in the specified order).
 3.5.8 
This command is compliant with ISO/IEC 7816-4.
 TCS_91 All tachograph cards shall support this command in the DF Tachograph generation 1. The command may or may not be accessible in the MF and / or the DF Tachograph_G2. If so, the command shall terminate with a suitable error code as the private key of the card (Card.SK) for the generation 1 authentication protocol is only accessible in the DF_Tachograph generation 1.

Using the INTERNAL AUTHENTICATE command, the IFD can authenticate the card. The authentication process is described in Appendix 11. It includes the following statements:
 TCS_92 The INTERNAL AUTHENTICATE command uses the card Private Key (implicitly selected) to sign authentication data including K1 (first element for session key agreement) and RND1, and uses the Public Key currently selected (through the last MSE command) to encrypt the signature and form the authentication token (more details in Appendix 11).
 TCS_93 
Byte Length Value Description
CLA 1 ‘00h’ CLA
INS 1 ‘88h’ INS
P1 1 ‘00h’ P1
P2 1 ‘00h’ P2
Lc 1 ‘10h’ Length of data sent to the card
#6 — #13 8 ‘XX..XXh’ Challenge used to authenticate the card
#14 -#21 8 ‘XX..XXh’ VU.CHR (see Appendix 11)
Le 1 ‘80h’ Length of the data expected from the card TCS_94 
Byte Length Value Description
#1-#128 128 ‘XX..XXh’ Card authentication token (see Appendix 11)
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If no Public Key is present in the Security Environment, the processing state returned is ‘6A88’.
— If no Private Key is present in the Security Environment, the processing state returned is ‘6A88’.
— If VU.CHR does not match the current public key identifier, the processing state returned is ‘6A88’.
— If the selected private key is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.
 TCS_95  
                                          Note:
                                        For generation 2 session keys see Appendix 11 CSM_193 and CSM_195. If generation 2 session keys are established and the tachograph card receives the plain INTERNAL AUTHENTICATE command APDU, it aborts the generation 2 secure messaging session and destroys the generation 2 session keys.
 3.5.9 
This command is compliant with ISO/IEC 7816-4.

Using the EXTERNAL AUTHENTICATE command, the card can authenticate the IFD. The authentication process is described in Appendix 11 for Tachograph G1 and G2 (VU authentication).
 TCS_96 The command variant for the generation 1 mutual authentication mechanism is only supported by a generation 1 tachograph application.
 TCS_97  
                                          Note:
                                        For generation 2 session keys see Appendix 11 CSM_193 and CSM_195. If generation 2 session keys are established and the tachograph card receives the plain EXTERNAL AUTHENTICATE command APDU, it aborts the generation 2 secure messaging session and destroys the generation 2 session keys.
 TCS_98 
Byte Length Value Description
CLA 1 ‘00h’ CLA
INS 1 ‘82h’ INS
P1 1 ‘00h’ Keys and algorithms implicitly known
P2 1 ‘00h’ 
Lc 1 ‘XXh’ Lc (Length of the data sent to the card )
#6-#(5+L) L ‘XX..XXh’ Generation 1 authentication: Cryptogram (see Appendix 11 Part A)Generation 2 authentication: Signature generated by the IFD (see Appendix 11 Part B) TCS_99 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the CHA of the currently set public key is not the concatenation of the Tachograph application AID and of a VU equipment Type, the processing state returned is ‘6F00’.
— If the command is not immediately preceded with a GET CHALLENGE command, the processing state returned is ‘6985’.

The Generation 1 Tachograph application may return the following additional error codes:


— If no Public Key is present in the Security Environment, ‘6A88’ is returned.
— If no Private Key is present in the Security Environment, the processing state returned is ‘6A88’.
— If the verification of the cryptogram is wrong, the processing state returned is ‘6688’.
— If the selected private key is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.

The command variant for the Generation 2 authentication may return the following additional error code:


— If signature verification failed, the card returns ‘6300’.
 3.5.10 
This command is used for the generation 2 chip authentication protocol specified in Appendix 11 Part B and is compliant with ISO/IEC 7816-4.
 TCS_100 The command can be performed in the MF, DF Tachograph and DF Tachograph_G2, see also TCS_34.
 TCS_101 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘86h’ 
P1 1 ‘00h’ Keys and protocol implicitly known
P2 1 ‘00h’ 
Lc 1 ‘NNh’ Lc: length of subsequent data field
#6-#(5+L) L ‘7Ch’ + L7C + ‘80h’ + L80 + ‘XX..XXh’ DER-TLV encoded ephemeral public key value (see Appendix 11)The VU shall send the data objects in this order.
5 + L + 1
                                              
                                                1
                                              
                                                ‘
                                                00h
                                                ’
                                              
                                                As specified in ISO/IEC 7816-4 TCS_102 
Byte Length Value Description
#1-#L L ‘7Ch’ + L7C + ‘81h’ + ‘08h’ + ‘XX..XXh’ + ‘82h’ + L82 + ‘XX..XXh’ DER-TLV encoded Dynamic Authentication Data: nonce and authentication token (see Appendix 11)
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— The card returns ‘6A80’ to indicate incorrect parameters in data field.
— The card returns ‘6982’ if the External Authenticate command has not been performed successfully

The response Dynamic Authentication Data object ‘7Ch’


— must be present if the operation is successful, i.e. the Status Words are ‘9000’,
— must be absent in case of an execution error or checking error, i.e. if the Status Words are in the range ‘6400’ — ‘6FFF’, and
— may be absent in case of a warning, i.e. if the Status Words are in the range ‘6200’ — ‘63FF’.
 3.5.11 
This command is used to set a public key for authentication purpose.
 3.5.11.1 
This command is compliant with ISO/IEC 7816-4. The use of this command is restricted regarding the related standard.
 TCS_103 This command is only supported by a generation 1 tachograph application.
 TCS_104 The key referenced in the MSE data field remains the current public key until the next correct MSE command, a DF is selected or the card is reset.
 TCS_105 If the key referenced is not (already) present into the card, the security environment remains unchanged.
 TCS_106 
Byte Length Value Description
CLA 1 ‘00h’ CLA
INS 1 ‘22h’ INS
P1 1 ‘C1h’ P1: referenced key valid for all cryptographic operations
P2 1 ‘B6h’ P2 (referenced data concerning Digital Signature)
Lc 1 ‘0Ah’ Lc: length of subsequent data field
#6 1 ‘83h’ Tag for referencing a public key in asymmetric cases
#7 1 ‘08h’ Length of the key reference (key identifier)
#8-#15 8 ‘XX..XXh’ Key identifier as specified in Appendix 11 TCS_107 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the referenced key is not present into the card, the processing state returned is ‘6A88’.
— If some expected data objects are missing in the secure messaging format, the processing state ‘6987’ is returned. This can happen if the tag ‘83h’ is missing.
— If some data objects are incorrect, the processing state returned is ‘6988’. This can happen if the length of the key identifier is not ‘08h’.
— If the selected key is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.
 3.5.11.2 
For the Generation 2 authentication the tachograph card supports the following MSE: Set command versions which are compliant with ISO/IEC 7816-4. These command versions are not supported for the Generation 1 authentication.
 3.5.11.2.1 
The following MSE:SET AT command is used to select the parameters for the Chip Authentication that is performed by a subsequent General Authenticate command.
 TCS_108 The command can be performed in the MF, DF Tachograph and DF Tachograph_G2, see also TCS_34.
 TCS_109 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘22h’ 
P1 1 ‘41h’ Set for internal authentication
P2 1 ‘A4h’ Authentication
Lc 1 ‘NNh’ Lc: length of subsequent data field
#6-#(5+L) L ‘80h’ + ‘0Ah’ + ‘XX..XXh’ DER-TLV encoded cryptographic mechanism reference: Object Identifier of Chip Authentication (value only, Tag ‘06h’ is omitted).See Appendix 1 for the values of object identifiers; the byte notation shall be used. See Appendix 11 for guidance on how to select one of these object identifiers. 3.5.11.2.2 
The following MSE:SET AT command is used to select the parameters and keys for the VU Authentication that is performed by a subsequent External Authenticate command.
 TCS_110 The command can be performed in the MF, DF Tachograph and DF Tachograph_G2, see also TCS_34.
 TCS_111 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘22h’ 
P1 1 ‘81h’ Set for external authentication
P2 1 ‘A4h’ Authentication
Lc 1 ‘NNh’ Lc: length of subsequent data field
#6-#(5+L) L ‘80h’ + ‘0Ah’ + ‘XX..XXh’ DER-TLV encoded cryptographic mechanism reference: Object Identifier of VU Authentication (value only, Tag ‘06h’ is omitted).See Appendix 1 for the values of object identifiers; the byte notation shall be used. See Appendix 11 for guidance on how to select one of these object identifiers.
‘83h’ + ‘08h’ + ‘XX..XXh’ DER-TLV encoded reference of the VU public key by the Certificate Holder Reference mentioned in its certificate.
‘91h’ + L91 + ‘XX..XXh’ DER-TLV encoded compressed representation of the ephemeral public key of the VU that will be used during Chip Authentication (see Appendix 11) 3.5.11.2.3 
The following MSE:SET DST command is used to set a public key either


— for the verification of a signature that is provided in a subsequent PSO: Verify Digital Signature command or
— for the signature verification of a certificate that is provided in a subsequent PSO: Verify Certificate command
 TCS_112 The command can be performed in the MF, DF Tachograph and DF Tachograph_G2, see also TCS_33.
 TCS_113 
Byte Length Value Description
CLA 1 ‘00h’ 
INS 1 ‘22h’ 
P1 1 ‘81h’ Set for verification
P2 1 ‘B6h’ Digital Signature
Lc 1 ‘NNh’ Lc: length of subsequent data field
#6-#(5+L) L ‘83h’ + ‘08h’ + ‘XX...XXh’ DER-TLV encoded reference of a public key, i.e. the Certificate Holder Reference in the certificate of the public key (see Appendix 11)
For all command versions the response message structure and status words are given by:
 TCS_114 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’. The protocol has been selected and initialised.
— ‘6A80’ indicates incorrect parameters in the command data field.
— ‘6A88’ indicates that referenced data (i.e. a referenced key) is not available.
— If the currentAuthenticatedTime of the card is later than the Expiration Date of the selected public key, the processing state returned is 
                                                         ‘
                                                         6A88
                                                         ’
                                                         .
                                                      
 
                                                Note:
                                              In the case of a MSE: SET AT for VU Authentication command, the referenced key is a VU_MA public key. The card shall set the VU_MA public key for use, if available in its memory, which matches the Certificate Holder Reference (CHR) given in the command data field (the card can identify VU_MA public keys by means of the certificate's CHA field). A card shall return ‘6A 88’ to this command in case only the VU_Sign public key or no public key of the Vehicle Unit is available. See the definition of the CHA field in Appendix 11 and of data type equipmentType in Appendix 1.

Similarly, in case an MSE: SET DST command referencing an EQT (i.e. a VU or a card) is sent to a control card, according to CSM_234 the referenced key is always an EQT_Sign key that has to be used for the verification of a digital signature. According to Figure 13 in Appendix 11, the control card will always have stored the relevant EQT_Sign public key. In some cases, the control card may have stored the corresponding EQT_MA public key. The control card shall always set the EQT_Sign public key for use when it receives an MSE: SET DST command.
 3.5.12 
This command is used to transfer to the card the result of a hash calculation on some data. This command is used for the verification of digital signatures. The hash value is stored temporarily for the subsequent command PSO: Verify Digital Signature

This command is compliant with ISO/IEC 7816-8. The use of this command is restricted regarding the related standard.

Only the control card is required to support this command in the DF Tachograph and DF Tachograph_G2.

Other types of tachograph cards may or may not implement this command. The command may or may not be accessible in the MF.

The control card application generation 1 supports only SHA-1.
 TCS_115 The temporarily stored hash value shall be deleted if a new hash value is computed by means of the PSO: HASH command, if a DF is selected, and if the tachograph card is reset.
 TCS_116 
Byte Length Value Description
CLA 1 ‘00h’ CLA
INS 1 ‘2Ah’ Perform Security Operation
P1 1 ‘90h’ Return Hash code
P2 1 ‘A0h’ Tag: data field contains DOs relevant for hashing
Lc 1 ‘XXh’ Length Lc of the subsequent data field
#6 1 ‘90h’ Tag for the hash code
#7 1 ‘XXh’ Length L of the hash code:
 ‘14h’ in Generation 1 application (see Appendix 11 Part A)
 ‘20h’, ‘30h’ or ‘40h’ in Generation 2 application (see Appendix 11 Part B)
#8-#(7+L) L ‘XX..XXh’ Hash code TCS_117 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If some expected data objects (as specified above) are missing, the processing state ‘6987’ is returned. This can happen if one of the tag ‘90h’ is missing.
— If some data objects are incorrect, the processing state returned is ‘6988’. This error happens if the required tag is present but with a length different from ‘14h’ for SHA-1, ‘20h’ for SHA-256, ‘30h’ for SHA-384, ‘40h’ for SHA-512 (Generation 2 application).
 3.5.13 
This command is not compliant with ISO/IEC 7816-8. Thus the CLA byte of this command indicates that there is a proprietary use of the PERFORM SECURITY OPERATION / HASH.

Only the driver card and the workshop card are required to support this command in the DF Tachograph and DF Tachograph_G2.

Other types of tachograph cards may or may not implement this command. If a company or control card implements this command, the command shall be implemented as specified in this chapter.

The command may or may not be accessible in the MF. If so, the command shall be implemented as specified in this chapter, i.e. shall not allow the calculation of a hash value, but terminate with a suitable error code.
 TCS_118 The PERFORM HASH of FILE command is used to hash the data area of the currently selected transparent EF.
 TCS_119 A tachograph card shall support this command only for the EFs that are listed in chapter 4 under the DF_Tachograph and DF_Tachograph_G2 with the following exception. A tachograph card shall not support the command for the EF Sensor_Installation_Data of DF Tachograph_G2..
 TCS_120 The result of the hash operation is stored temporarily in the card. It can then be used to get a digital signature of the file, using the PSO: COMPUTE DIGITAL SIGNATURE command.
 TCS_121 The temporarily stored hash of file value shall be deleted if a new hash of file value is computed by means of the PERFORM HASH of FILE command, if a DF is selected, and if the tachograph card is reset.
 TCS_122 The Tachograph Generation 1 application shall support SHA-1.
 TCS_123 The Tachograph Generation 2 application shall support the SHA-2 algorithm (SHA-256, SHA-384 or SHA-512), specified by the cipher suite in Appendix 11 Part B for the card signature key Card_Sign.
 TCS_124 
Byte
                                              
                                                Length
                                              
                                                Value
                                              
                                                Description
                                             

                                                CLA
                                              
                                                1
                                              
                                                ‘
                                                80h
                                                ’
                                              
                                                CLA
                                             

                                                INS
                                              
                                                1
                                              
                                                ‘
                                                2Ah
                                                ’
                                              
                                                Perform Security Operation
                                             

                                                P1
                                              
                                                1
                                              
                                                ‘
                                                90h
                                                ’
                                              
                                                Tag: Hash
                                             

                                                P2
                                              
                                                1
                                              
                                                ‘
                                                00h
                                                ’
                                              Algorithm implicitly knownFor the Tachograph Generation 1 application: SHA-1For the Tachograph Generation 2 application: SHA-2 algorithm (SHA-256, SHA-384 or SHA-512) defined by the cipher suite in Appendix 11 Part B for the card signature key Card_Sign TCS_125 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the current EF does not allow this command (EF Sensor_Installation_Data in DF Tachograph_G2), the processing state ‘6985’ is returned.
— If the selected EF is considered corrupted (file attributes or stored data integrity errors), the processing state returned is ‘6400’ or ‘6581’.
— If the selected file is not a transparent file or if there is no current EF, the processing state returned is ‘6986’.
 3.5.14 
This command is used to compute the digital signature of previously computed hash code (see PERFORM HASH of FILE, §3.5.13).

Only the driver card and the workshop card are required to support this command in the DF Tachograph and DF Tachograph_G2.

Other types of tachograph cards may or may not implement this command. In case of the Generation 2 tachograph application, only the driver card and the workshop card have a generation 2 signature key, other cards are not able to successfully perform the command and terminate with a suitable error code.

The command may or may not be accessible in the MF. If the command is not accessible in the MF, it shall terminate with a suitable error code.

This command is compliant with ISO/IEC 7816-8. The use of this command is restricted regarding the related standard.
 TCS_126 This command shall not compute a digital signature of previously computed hash code with the PSO: HASH command.
 TCS_127 The card private key is used to compute the digital signature and is implicitly known by the card.
 TCS_128 The Generation 1 tachograph application performs a digital signature using a padding method compliant with PKCS1 (see Appendix 11 for details).
 TCS_129 The Generation 2 tachograph application computes an elliptic curve based digital signature (see Appendix 11 for details).
 TCS_130 
Byte Length Value Description
CLA 1 ‘00h’ CLA
INS 1 ‘2Ah’ Perform Security Operation
P1 1 ‘9Eh’ Digital signature to be returned
P2 1 ‘9Ah’ Tag: data field contains data to be signed. As no data field is included, the data are supposed to be already present in the card (hash of file)
Le 1 ‘NNh’ Length of the expected signature TCS_131 
Byte Length Value Description
#1-#L L ‘XX..XXh’ Signature of the previously computed hash
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the implicitly selected private key is considered as corrupted, the processing state returned is ‘6400’ or ‘6581’.
— If the hash which was computed in a previous Perform Hash of File command is not available, the processing state returned is ‘6985’.
 3.5.15 
This command is used to verify the digital signature, provided as an input, whose hash is known to the card. The signature algorithm is implicitly known by the card.

This command is compliant with ISO/IEC 7816-8. The use of this command is restricted regarding the related standard.

Only the control card is required to support this command in the DF Tachograph and DF Tachograph_G2.

Other types of tachograph cards may or may not implement this command. The command may or may not be accessible in the MF.
 TCS_132 The VERIFY DIGITAL SIGNATURE command always uses the public key selected by the previous Manage Security Environment MSE: Set DST command and the previous hash code entered by a PSO: HASH command.
 TCS_133 
Byte
                                              
                                                Length
                                              
                                                Value
                                              
                                                Description
                                             

                                                CLA
                                              
                                                1
                                              
                                                ‘
                                                00h
                                                ’
                                              
                                                CLA
                                             

                                                INS
                                              
                                                1
                                              
                                                ‘
                                                2Ah
                                                ’
                                              
                                                Perform Security Operation
                                             

                                                P1
                                              
                                                1
                                              
                                                ‘
                                                00h
                                                ’
                                              

                                                P2
                                              
                                                1
                                              
                                                ‘
                                                A8h
                                                ’
                                              
                                                Tag: data field contains DOs relevant for verification
                                             

                                                Lc
                                              
                                                1
                                              
                                                ‘
                                                XXh
                                                ’
                                              
                                                Length Lc of the subsequent data field
                                             

                                                #6
                                              
                                                1
                                              
                                                ‘
                                                9Eh
                                                ’
                                              
                                                Tag for Digital Signature
                                             
#7 or#7-#8 
                                                L
                                              ‘NNh’ or‘81 NNh’ Length of digital signature (L is 2 bytes if the digital signature is longer than 127 bytes):
 128 bytes coded in accordance with Appendix 11 Part A for Tachograph Generation 1 application.
 Depending on the selected curve for Tachograph Generation 2 application (see Appendix 11 Part B).

                                                #(7+L)-#(6+L+NN)
                                              
                                                NN
                                              
                                                ‘
                                                XX..XXh
                                                ’
                                              
                                                Digital signature content TCS_134 
Byte Length Value Description
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— If the verification of the signature fails, the processing state returned is ‘6688’. The verification process is described in Appendix 11.
— If no public key is selected, the processing state returned is ‘6A88’.
— If some expected data objects (as specified above) are missing, the processing state ‘6987’ is returned. This can happen if one of the required tag is missing.
— If no hash code is available to process the command (as a result of a previous PSO: Hash command), the processing state returned is ‘6985’.
— If some data objects are incorrect, the processing state returned is ‘6988’. This can happen if one of the required data objects length is incorrect.
— If the selected public key is considered corrupted, the processing state returned is ‘6400’ or ‘6581’.
— If the selected public key (used to verify the digital signature) has a CHA.LSB (CertificateHolderAuthorisation.equipmentType) that is not suitable for the digital signature verification according to Appendix 11, the processing state returned is ‘
                                                   6985
                                                ’.
 3.5.16 
This command is used to verify the integrity and authenticity of the DSRC message and to decipher the data communicated from a VU to a control authority or a workshop over the DSRC link. The card derives the encryption key and the MAC key used to secure the DSRC message as described in Appendix 11 Part B chapter 13.

Only the control card and the workshop card are required to support this command in the DF Tachograph_G2.

Other types of tachograph cards may or may not implement this command, but shall not have a DSRC master key. Therefore these cards cannot perform the command successfully, but terminate with a suitable error code.

The command may or may not be accessible in the MF and / or the DF Tachograph. If so, the command shall terminate with a suitable error code.
 TCS_135 The DSRC master key is accessible only in the DF Tachograph_G2, i.e. the control and workshop card shall support a successful execution of the command only in the DF Tachograph_G2.
 TCS_136 The command shall only decrypt the DSRC data and verify the cryptographic checksum, but not interpret the input data.
 TCS_137 The order of the data objects in the command data field is fixed by this specification.
 TCS_138 
Byte Length Value Description
CLA 1 ‘80h’ Proprietary CLA
INS 1 ‘2Ah’ Perform Security Operation
P1 1 ‘80h’ Response data: plain value
P2 1 ‘B0h’ Command data: plain value encoded in BER-TLV and including SM DOs
Lc 1 ‘NNh’ Length Lc of the subsequent data field
#6-#(5+L) L ‘87h’ + L87 + ‘XX..XXh’ DER-TLV encoded padding-content indicator byte followed by encrypted tachograph payload. For the padding-content indicator byte the value ‘00h’ (‘no further indication’ according to ISO/IEC 7816-4:2013 Table 52) shall be used. For the encryption mechanism see Appendix 11, Part B chapter 13.Allowed values for the length L87 are the multiples of the AES block length plus 1 for the padding-content indicator byte, i.e. from 17 bytes up to and including 193 bytes.Note: See ISO/IEC 7816-4:2013 Table 49 for the SM data object with tag ‘87h’.
‘81h’ + ‘10h’ DER-TLV encoded Control Reference Template for Confidentiality nesting the concatenation of the following data elements (see Appendix 1 DSRCSecurityData and Appendix 11 Part B chapter 13):
— 4 byte time stamp
— 3 byte counter
— 8 byte VU serial number
— 1 byte DSRC master key versionNote: See ISO/IEC 7816-4:2013 Table 49 for the SM data object with tag ‘81h’.
‘8Eh’ + L8E + ‘XX..XXh’ DER-TLV encoded MAC over the DSRC message. For the MAC algorithm and calculation see Appendix 11, Part B chapter 13.Note: See ISO/IEC 7816-4:2013 Table 49 for the SM data object with tag ‘8Eh’.
5 + L + 1
                                              
                                                1
                                              
                                                ‘
                                                00h
                                                ’
                                              
                                                As specified in ISO/IEC 7816-4 TCS_139 
Byte Length Value Description
#1-#L L ‘XX..XXh’ Absent (in case of an error) or deciphered data (padding removed)
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the card returns ‘9000’.
— ‘6A80’ indicates incorrect parameters in the command data field (also used in case the data objects are not sent in the specified order).
— ‘6A88’ indicates that referenced data is not available, i.e. the referenced DSRC master key is not available.
— ‘6900’ indicates that the verification of the cryptographic checksum or the decryption of the data failed.
— ‘6985
                                                ’ indicates that the 4-byte time stamp provided in the command data field is earlier than cardValidityBegin or later than cardExpiryDate.
 4. 
This paragraph specifies the file structures of the Tachograph cards for storage of accessible data.

It does not specify card manufacturer dependent internal structures, such as e.g. file headers, nor storage and handling of data elements needed for internal use only such as ,, or.
 TCS_140 A generation 2 tachograph card shall host the Master File MF and a generation 1 and a generation 2 tachograph application of the same type (e.g. driver card applications).
 TCS_141 
The maximum and minimum numbers of records are specified in this chapter for the different applications.

For the security conditions used in the access rules throughout this chapter please refer to chapter 3.3. In general the access mode ‘read’ denotes the READ BINARY command with even and if supported odd INS byte with the exception of the EF Sensor_Installation_Data on the workshop card, see TCS_156 and TCS_160. The access mode ‘update’ denotes the Update Binary command with even and if supported odd INS byte and the access mode ‘select’ the SELECT command.
 4.1.  TCS_142 Note: The short EF identifier SFID is given as decimal number, e.g. the value 30 corresponds to 11110 in binary.


The following abbreviation for the security condition is used in this table:

SC1ALW OR SM-MAC-G2
 TCS_143 All EF structures shall be transparent.
 TCS_144 

 TCS_145 The elementary file EF DIR shall contain the following application related data objects: ‘61 08 4F 06 FF 54 41 43 48 4F 61 08 4F 06 FF 53 4D 52 44 54’
 TCS_146 The elementary file EF ATR/INFO shall be present if the tachograph card indicates in its ATR that it supports extended length fields. In this case the EF ATR/INFO shall contain the extended length information data object (DO‘7F66’) as specified in ISO/IEC 7816-4:2013 clause 12.7.1.
 TCS_147 
The value ‘01’ indicates extended length field support for the T = 1 protocol.

The value ‘10’ indicates extended length field support for the T = 0 protocol.

The value ‘11’ indicates extended length field support for the T = 1 and the T = 0 protocol.
 4.2.  4.2.1  TCS_148 


The following abbreviations for the security conditions are used in this table:

SC1ALW OR SM-MAC-G2SC2ALW OR SM-MAC-G1 OR SM-MAC-G2SC3SM-MAC-G1 OR SM-MAC-G2
 TCS_149 All EF structures shall be transparent.
 TCS_150 



 TCS_151 

 4.2.2  TCS_152 Note: The short EF identifier SFID is given as decimal number, e.g. the value 30 corresponds to 11110 in binary.


The following abbreviation for the security condition is used in this table:

SC1ALW OR SM-MAC-G2
 TCS_153 All EF structures shall be transparent.
 TCS_154 





 TCS_155 

 4.3.  4.3.1  TCS_156 


The following abbreviations for the security conditions are used in this table:

SC1ALW OR SM-MAC-G2SC2ALW OR SM-MAC-G1 OR SM-MAC-G2SC3SM-MAC-G1 OR SM-MAC-G2SC4
                                             For the READ BINARY command with even INS byte:
 (SM-C-MAC-G1 AND SM-R-ENC-MAC-G1) OR
 (SM-C-MAC-G2 AND SM-R-ENC-MAC-G2)
 For the READ BINARY command with odd INS byte (if supported): NEV
 TCS_157 All EF structures shall be transparent.
 TCS_158 





 TCS_159 

 4.3.2  TCS_160 Note: The short EF identifier SFID is given as decimal number, e.g. the value 30 corresponds to 11110 in binary.


The following abbreviations for the security conditions are used in this table:

SC1ALW OR SM-MAC-G2SC5For the Read Binary command with even INS byte: SM-C-MAC-G2 AND SM-R-ENC-MAC-G2
For the Read Binary command with odd INS byte (if supported): NEV
 TCS_161 All EFs structures shall be transparent.
 TCS_162 





 TCS_163 

 4.4.  4.4.1  TCS_164 


The following abbreviations for the security conditions are used in this table:

SC1ALW OR SM-MAC-G2SC2ALW OR SM-MAC-G1 OR SM-MAC-G2SC3SM-MAC-G1 OR SM-MAC-G2SC6EXT-AUT-G1 OR SM-MAC-G1 OR SM-MAC-G2
 TCS_165 All EF structures shall be transparent.
 TCS_166 

 TCS_167 

 4.4.2  TCS_168 Note: The short EF identifier SFID is given as decimal number, e.g. the value 30 corresponds to 11110 in binary.


The following abbreviation for the security condition is used in this table:

SC1ALW OR SM-MAC-G2
 TCS_169 All EF structures shall be transparent.
 TCS_170 

 TCS_171 

 4.5.  4.5.1  TCS_172 


The following abbreviations for the security conditions are used in this table:

SC1ALW OR SM-MAC-G2SC2ALW OR SM-MAC-G1 OR SM-MAC-G2SC3SM-MAC-G1 OR SM-MAC-G2SC6EXT-AUT-G1 OR SM-MAC-G1 OR SM-MAC-G2
 TCS_173 All EF structures shall be transparent.
 TCS_174 

 TCS_175 

 4.5.2  TCS_176 Note: The short EF identifier SFID is given as decimal number, e.g. the value 30 corresponds to 11110 in binary.


The following abbreviation for the security condition is used in this table:

SC1ALW OR SM-MAC-G2
 TCS_177 All EF structures shall be transparent.
 TCS_178 

 TCS_179 


Appendix 3 PIC_001 

1.. BASIC PICTOGRAMS

 People Actions Modes of operation
 Company  Company mode
 Controller Control Control mode
 Driver Driving Operational mode
 Workshop/test station Inspection/calibration Calibration mode
 Manufacturer  
 Activities Duration
 Available Current availability period
 Driving Continuous driving time
 Rest Current rest period
 Other Work Current work period
 Break Cumulative break time
 Unknown 
 Equipment Functions
 Driver slot 
 Co-driver slot 
 Card 
 Clock 
 Display Displaying
 External storage Downloading
 Power supply 
 Printer/printout Printing
 Sensor 
 Tyre size 
 Vehicle/vehicle unit 
 GNSS facility 
 Remote Detection facility 
 ITS interface 
 Specific conditions
 Out of scope
 Ferry/train crossing
 Miscellaneous  
 Events  Faults
 Start of daily work period  End of daily work period
 Location  
 Manual entry of driver activities  
 Security  
 Speed  
 Time  
 Total/summary  
 Qualifiers
24h Daily
 Weekly
 Two weeks
 From or to
2.. PICTOGRAM COMBINATIONS

 Miscellaneous  
 Control place  
 Location start of daily work period  Location end of daily work period
 Position after 3 hours accumulated driving time
                                                  
 From time  To time
 From vehicle  
 Out of scope begin  Out of scope end
 Cards
 Driver card
 Company card
 Control card
 Workshop card
 No card
 Driving
 Crew driving
 Driving time for one week
 Driving time for two weeks
 Printouts
 Driver activities from card daily printout
 Driver activities from VU daily printout
 Events and faults from card printout
 Events and faults from VU printout
 Technical data printout
 Over speeding printout
 Events
 Insertion of a non valid card
 Card conflict
 Time overlap
 Driving without an appropriate card
 Card insertion while driving
 Last card session not correctly closed
 Over speeding
 Power supply interruption
 Motion data error
 Vehicle motion conflict
 Security breach
 Time conflict or time adjustment (by workshop)
 Over speeding control
 Absence of position information from GNSS receiver or Communication error with the external GNSS facility
                                                
 
                                                   Communication error with the remote communication facility
 Faults
 Card fault (driver slot)
 Card fault (co-driver slot)
 Display fault
 Downloading fault
 Printer fault
 Sensor fault
 VU internal fault
 GNSS fault
 Remote Detection fault
 Manual entries procedure
 Still same daily work period ?
 End of previous work period ?
 Confirm or enter location of end of work period
 Enter start time
 Enter location of start of work period.
Note: Additional pictogram combinations to form printout blocks or record identifiers are defined in Appendix 4.
Appendix 4 1. 
Each printout is built up by chaining various data blocks, possibly identified with a block identifier.

A data block contains one or more records, possibly identified with a record identifier.

PRT_001When a block identifier immediately precedes a record identifier, the record identifier is not printed.PRT_002In the case where a data item is unknown, or must not be printed for data access rights reasons, spaces are printed instead.PRT_003If the content of a complete line is unknown, or need not to be printed, then the complete line is omitted.PRT_004Numerical data fields are printed right aligned, with a space separator for thousands and millions, and without leading zeros.PRT_005String data fields are printed left aligned and filled up with spaces to data item length, or truncated to data item length when needed (names and addresses).PRT_006In case of a line-break due to a long text a special character (dot at middle line-height, ‘•’) should be printed as first character in the new line.
 2. 
In this chapter the following format notation conventions have been used:


— Characters printed in bold denote plain text to be printed (printing remains in normal characters),
— Normal characters denote variables (pictograms or data) to be replaced by their values for printing,
— Variable names have been padded with underscores to show the data item length available for the variable,
— Dates are specified with a ‘dd/mm/yyyy’ (day, month, year) format. A ‘dd.mm.yyyy’ format may also be used,
— The term ‘card identification’ denotes the composition of: the type of card through a card pictograms combination, the card issuing Member State code, a forward slash character and the card number with the replacement index and the renewal index separated with a space:
P  x x x / x x x x x x x x x x x x x x  x  x
Card Pictogram combination Issuing Member State code  First 14 characters of card number(possibly including a consecutive index)  Replacement index  Renewal index
 PRT_007 

 3. 
In this chapter the following notation conventions have been used:


N Print block or record number N

N Print block or record number N repeated as many times as necessary

X/Y Print blocks or records X and/or Y as needed, and repeating as many times as necessary.
 3.1.  PRT_008 
1 Date and time at which the document is printed
2 Type of printout
3 Controller identification (if a control card is inserted in the VU)
3 Driver identification (from card subject of the printout + GEN)
4 Vehicle identification (vehicle from which printout is taken)
5 VU identification (VU from which printout is taken + GEN)
6 Last calibration of this VU
7 Last control the inspected driver has been subject to
8 Driver activities delimiter
8a Out of scope condition in the beginning of this day
8.1a/8.1b/8.1c/8.2/8.3/8.3a/8.4 Activities of the driver in order of occurrence
11 Daily summary delimiter
11.4 Places entered in chronological order
11.5
                                           
                                             Positions after 3 hours accumulated driving time in chronological order
11.6 Activity totals
12.1 Events or faults from card delimiter
12.4 Event/Fault records (Last 5 events or faults stored in the card)
13.1 Events or faults from VU delimiter
13.4 Event/Fault records (Last 5 events or faults stored or on-going in the VU)
22.1 Control place
22.2 Controller's signature
22.5 Driver's signature 3.2.  PRT_009 
1
                                           
                                             Date and time at which the document is printed
                                          

                                             2
                                           
                                             Type of printout
                                          

                                             3
                                           
                                             Card holder identification (for all cards inserted in VU + GEN)
                                          

                                             4
                                           
                                             Vehicle identification (vehicle from which printout is taken)
                                          

                                             5
                                           
                                             VU identification (VU from which printout is taken + GEN)
                                          

                                             6
                                           
                                             Last calibration of this VU
                                          

                                             7
                                           
                                             Last control on this tachograph
                                          

                                             9
                                           
                                             Driver activities delimiter
                                          

                                             10
                                           
                                             Driver slot delimiter (slot 1)
                                          

                                             10a
                                           
                                             Out of scope condition in the beginning of this day
                                          

                                             10.1 / 10.2 / 10.3 / 10.3a / 10.4
                                           
                                             Activities in chronological order (driver slot)
                                          

                                             10
                                           
                                             Co-driver slot delimiter (slot 2)
                                          

                                             10a
                                           
                                             Out of scope condition in the beginning of this day
                                          

                                             10.1 / 10.2 / 10.3 / 10.3a / 10.4
                                           
                                             Activities in chronological order (co-driver slot)
                                          

                                             11
                                           
                                             Daily summary delimiter
                                          

                                             11.1
                                           
                                             Summary of periods without card in driver slot
                                          

                                             11.4
                                           
                                             Places entered in chronological order
                                          

                                             11.5
                                           
                                             Positions after 3 hours accumulated driving time in chronological order
                                          

                                             11.7
                                           
                                             Activity totals
                                          

                                             11.2
                                           
                                             Summary of periods without card in co-driver slot
                                          

                                             11.4
                                           
                                             Places entered in chronological order
                                          

                                             11.5
                                           
                                             Positions after 3 hours accumulated driving time in chronological order
                                          

                                             11.8
                                           
                                             Activity totals
                                          

                                             11.3
                                           
                                             Summary of activities for a driver both slots included
                                          
 
                                             11.4
                                            
                                             Places entered by this driver in chronological order
                                          
 
                                             11.5
                                            
                                             Positions after 3 hours accumulated driving time in chronological order
                                          

                                             11.9
                                           
                                             Activity totals for this driver
                                          

                                             13.1
                                           
                                             Events faults delimiter
                                          

                                             13.4
                                           
                                             Event/Fault records (Last 5 events or faults stored or on-going in the VU)
                                          

                                             22.1
                                           
                                             Control place
                                          

                                             22.2
                                           
                                             Controller’s signature
                                          

                                             22.3
                                           
                                             From time (space available for a driver without a card to indicate
                                          

                                             22.4
                                           
                                             To time which periods are relevant to himself)
                                          

                                             22.5
                                           
                                             Driver's signature 3.3.  PRT_010 
1 Date and time at which the document is printed
2 Type of printout
3 Controller identification (if a control card is inserted in the VU + GEN)
3 Driver identification (from card subject of the printout)
4 Vehicle identification (vehicle from which printout is taken)
12.2 Events delimiter
12.4 Event records (all events stored on the card)
12.3 Faults delimiter
12.4 Fault records (all faults stored on the card)
22.1 Control place
22.2 Controller's signature
22.5 Driver's signature 3.4.  PRT_011 
1 Date and time at which the document is printed
2 Type of printout
3 Card holder identification (for all cards inserted in VU + GEN)
4 Vehicle identification (vehicle from which printout is taken)
13.2 Events delimiter
13.4 Event records (All Events stored or on-going in the VU)
13.3 Faults delimiter
13.4 Fault records (All Faults stored or on-going in the VU)
22.1 Control place
22.2 Controller's signature
22.5 Driver's signature 3.5.  PRT_012 
1 Date and time at which the document is printed
2 Type of printout
3 Card holder identification (for all cards inserted in VU + GEN)
4 Vehicle identification (vehicle from which printout is taken)
14 VU identification
15 Sensor identification
15.1 Sensor Pairing data (all data available in chronological order)
16 GNSS identification
16.1 External GNSS facility coupling data (all data available in chronological order)
17 Calibration data delimiter
17.1 Calibration records (all records available in chronological order)
18 Time adjustment delimiter
18.1 Time adjustment records (all records available from time adjustment and from calibration data records)
19 Most recent event and Fault recorded in the VU 3.6.  PRT_013 
1 Date and time at which the document is printed
2 Type of printout
3 Card holder identification (for all cards inserted in VU + GEN)
4 Vehicle identification (vehicle from which printout is taken)
20 Over speeding control information
21.1 Over speeding data identifier
21.4/21.5 First over speeding after the last calibration
21.2 Over speeding data identifier
21.4/21.5 The 5 most serious over speeding events over the last 365 days
21.3 Over speeding data identifier
21.4/21.5 The most serious over speeding for each of the last 10 days of occurrence
22.1 Control place
22.2 Controller's signature
22.5 Driver's signature 3.7.  PRT_014 

                                             1
                                           
                                             Date and time at which the document is printed
                                          

                                             2
                                           
                                             Type of printout
                                          

                                             3
                                           
                                             Card holder identifications (of all cards inserted in the VU)
                                          

                                             23
                                           
                                             Most recent card inserted in the VU
                                          

                                             23.1
                                           
                                             Inserted cards (up to 88 records)
                                          

                                             12.3
                                           
                                             Faults delimiter
Appendix 5
In this appendix the following format notation conventions have been used:


— characters printed in bold denote plain text to be displayed (display remains in normal character),
— normal characters denote variables (pictograms or data) to be replaced by their values for displaying:
— dd mm yyyyday, month, year,— hhhours,— mmminutes,— Dduration pictogram,— EFevent or fault pictograms combination,— Omode of operation pictogram.
 DIS_001 
Data Format
Default display
Local time 
Mode of operation 
Information related to the driver 
Information related to the co-driver 
Out of scope condition opened 
Warning display
Exceeding continuous driving time 
Event or fault 
Other displays
UTC date 
time
Driver's continuous driving time and cumulative break time 
Co-driver's continuous driving time and cumulative break time 
Driver's cumulated driving time for the previous and the current week 
Co-driver's cumulated driving time for the previous and the current week 
Appendix 6 1.  1.1.  INT_001 


The following diagram shows a typical 6 pin mating plug:


 1.2.  INT_002 
Pin Description Remark
1 Battery minus Connected to the battery minus of the vehicle
2 Data communication K-line (ISO 14230-1)
3 RxD — Downloading Data input to tachograph
4 Input/output signal Calibration
5 Permanent power output The voltage range is specified to be that of the vehicle power minus 3V to allow for the voltage drop across the protective circuitryOutput 40 mA
6 TxD — Downloading Data output from tachograph 1.3.  INT_003 

 2.  INT_004 The downloading interface shall comply to RS232 specifications.
 INT_005 


Start bitone bit with logic level 0;Data bitstransmitted with LSB first;Parity biteven parityStop bitone bit with logic level 1

When numerical data composed by more than one byte are transmitted, the most significant byte is transmitted first and the least significant byte last.
 INT_006 Transmission baud rates shall be adjustable from 9 600 bps to 115 200 bps. Transmission shall be achieved at the highest possible transmission speed, the initial baud rate after a start of communication being set at 9 600 bps.
 3.  INT_007 The data communication shall comply to ISO 14230-1 Road vehicles — Diagnostic systems — Keyword protocol 2000 — Part 1: Physical layer, First edition: 1999.
 INT_008 
Parameter Minimum Typical Maximum Remark
U low (in)   1,0 V I = 750 μA
U high (in) 4 V   I = 200 μA
Frequency   4 kHz 
U low (out)   1,0 V I = 1 mA
U high (out) 4 V   I = 1 mA INT_009 


Appendix 7 1. 
This appendix specifies the procedures to follow in order to perform the different types of data download to an External Storage Medium, together with the protocols that must be implemented to assure the correct data transfer and the full compatibility of the downloaded data format to allow any controller to inspect these data and be able to control their authenticity and their integrity before analysing them.
 1.1. 
Data may be downloaded to an ESM:


— from a Vehicle Unit by an Intelligent Dedicated Equipment (IDE) connected to the VU,
— from a tachograph card by an IDE fitted with a card interface device (IFD),
— from a tachograph card via a vehicle unit by an IDE connected to the VU.

To give the possibility to verify the authenticity and integrity of downloaded data stored on an ESM, data is downloaded with a signature appended in accordance with Appendix 11 Common Security Mechanisms. The source equipment (VU or card) identification and its security certificates (Member state and equipment) are also downloaded. The verifier of the data must possess independently a trusted European public key.

Data downloaded from a VU are signed using Appendix 11 Common Security Mechanisms Part B (Second-generation tachograph system), except when drivers' control is performed by a non EU control authority, using a first generation control card, in which case data are signed using Appendix 11 Common Security Mechanisms Part A (First-generation tachograph system), as requested by Appendix 15 Migration, requirement MIG_015.

This Appendix specifies therefore two types of data downloads from the VU:


— Generation 2 type of VU data download, providing the generation 2 data structure, signed using Appendix 11 Common Security Mechanisms Part B,
— Generation 1 type of VU data download, providing the generation 1 data structure, signed using Appendix 11 Common Security Mechanisms Part A.

Similarly, there are two types of data downloads from second generation driver cards inserted in a VU, as specified in paragraphs 3 and 4 of this Appendix.
 1.2. 
The following acronyms are used in this appendix:

AIDApplication IdentifierATRAnswer To ResetCSChecksum byteDFDedicated FileDS_Diagnostic SessionEFElementary FileESMExternal Storage MediumFIDFile Identifier (File ID)FMTFormat Byte (first byte of message header)ICCIntegrated Circuit CardIDEIntelligent Dedicated Equipment: The equipment used to perform data downloading to the ESM (e.g. Personal Computer)IFDInterface DeviceKWPKeyword Protocol 2000LENLength Byte (last byte of message header)PPSProtocol Parameter SelectionPSOPerform Security OperationSIDService IdentifierSRCSource byteTGTTarget ByteTLVTag Length ValueTREPTransfer Response ParameterTRTPTransfer Request ParameterVUVehicle Unit
 2.  2.1. 
In order to carry on a VU data download, the operator must perform the following operations:


— Insert his tachograph card inside a card slot of the VU;
— Connect the IDE to the VU download connector;
— Establish the connection between the IDE and the VU;
— Select on the IDE the data to download and send the request to the VU;
— Close the download session.
 2.2. 
The protocol is structured on a master-slave basis, with the IDE playing the master role and the VU playing the slave role.

The message structure, types and flow are principally based on the Keyword Protocol 2000 (KWP) (ISO 14230-2 Road vehicles — Diagnostic systems — Keyword protocol 2000 — Part2: Data link layer).

The application layer is principally based on the current draft to date of ISO 14229-1 (Road vehicles — Diagnostic systems — Part 1: Diagnostic services, version 6 of 22 February 2001).
 2.2.1  DDP_002 

— Header composed by a Format byte (FMT), a Target byte (TGT), a Source byte (SRC) and possibly a Length byte (LEN),
— Data field composed by a Service Identifier byte (SID) and a variable number of data bytes, which can include an optional diagnostic session byte (DS_) or an optional transfer parameter byte (TRTP or TREP).
— Checksum composed by a Checksum byte (CS).

Header Data field Checksum
FMT TGT SRC LEN SID DATA … … … CS
4 bytes Max 255 bytes 1 byte
The TGT and SRC byte represent the physical address of the recipient and originator of the message. Values are F0 Hex for the IDE and EE Hex for the VU.

The LEN byte is the length of the Data field part.

The Checksum byte is the 8 bit sum series modulo 256 of all the bytes of the message excluding the CS itself.

FMT, SID, DS_, TRTP and TREP bytes are defined later in this document.
 DDP_003 In the case where the data to be carried by the message is longer than the space available in the data field part, the message is actually sent in several sub messages. Each sub message bears a header, the same SID, TREP and a 2-byte sub message counter indicating the sub message number within the total message. To enable error checking and abort the IDE acknowledges every sub message. The IDE can accept the sub message, ask for it to be re-transmitted, request the VU to start again or abort the transmission.
 DDP_004 
Example:

Header SID TREP Message CS
4 Bytes Longer than 255 Bytes 
Will be transmitted as:

Header SID TREP 00 01 Sub message 1 CS
4 Bytes 255 Bytes Header SID TREP 00 02 Sub message 2 CS
4 Bytes 255 Bytes 
…

Header SID TREP xx yy Sub message n CS
4 Bytes Less than 255 Bytes 
or as:

Header SID TREP 00 01 Sub message 1 CS
4 Bytes 255 Bytes Header SID TREP 00 02 Sub message 2 CS
4 Bytes 255 Bytes 
…

Header SID TREP xx yy Sub message n CS
4 Bytes 255 Bytes Header SID TREP xx yy + 1 CS
4 Bytes 4 bytes  2.2.2 
The communication protocol for data download between the VU and the IDE requires the exchange of 8 different message types.

The following table summarises these messages.


Message Structure
                                              
                                                Max 4 Bytes Header
                                              
                                                Max 255 Bytes Data
                                              
                                                1 Byte CheckSum
                                             

                                                   IDE ->
                                                 
                                                   <- VU
                                                 
                                                FMT
                                              
                                                TGT
                                              
                                                SRC
                                              
                                                LEN
                                              
                                                SID
                                              
                                                DS_ / TRTP
                                              
                                                DATA
                                              
                                                CS
                                             

                                                Start Communication Request
                                              
                                                81
                                              
                                                EE
                                              
                                                F0
                                               
                                                81
                                                
                                                E0
                                             

                                                Positive Response Start Communication
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                C1
                                               
                                                EA, 8F
                                              
                                                9B
                                             

                                                Start Diagnostic Session Request
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                10
                                              
                                                81
                                               
                                                F1
                                             

                                                Positive Response Start Diagnostic
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                02
                                              
                                                50
                                              
                                                81
                                               
                                                31
                                             

                                                Link Control Service
                                              

                                                Verify Baud Rate (stage 1)
                                              

                                                9 600
                                                 Bd
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                04
                                              
                                                87
                                               
                                                01,01,01
                                              
                                                EC
                                             

                                                19 200
                                                 Bd
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                04
                                              
                                                87
                                               
                                                01,01,02
                                              
                                                ED
                                             

                                                38 400
                                                 Bd
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                04
                                              
                                                87
                                               
                                                01,01,03
                                              
                                                EE
                                             

                                                57 600
                                                 Bd
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                04
                                              
                                                87
                                               
                                                01,01,04
                                              
                                                EF
                                             

                                                115 200
                                                 Bd
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                04
                                              
                                                87
                                               
                                                01,01,05
                                              
                                                F0
                                             

                                                Positive Response Verify Baud Rate
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                02
                                              
                                                C7
                                               
                                                01
                                              
                                                28
                                             

                                                Transition Baud Rate (stage 2)
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                03
                                              
                                                87
                                               
                                                02,03
                                              
                                                ED
                                             

                                                Request Upload
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                0A
                                              
                                                35
                                               00,00,00,00,00,FF,FF,FF,FF 
                                                99
                                             

                                                Positive Response Request Upload
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                75
                                               
                                                00,FF
                                              
                                                D5
                                             

                                                Transfer Data Request
                                              

                                                Overview
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                36
                                              
                                                01 or 21
                                               
                                                97
                                             

                                                Activities
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                06
                                              
                                                36
                                              
                                                02 or 22
                                              
                                                Date
                                              
                                                CS
                                             

                                                Events & Faults
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                36
                                              
                                                03 or 23
                                              
                                                Date
                                              
                                                99
                                             

                                                Detailed Speed
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                36
                                              
                                                04 or 24
                                              
                                                Date
                                              
                                                9 A
                                             

                                                Technical Data
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                36
                                              
                                                05 or 25
                                              
                                                Date
                                              
                                                9B
                                             

                                                Card download
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                02
                                              
                                                36
                                              
                                                06
                                              
                                                Slot
                                              
                                                CS
                                             

                                                Positive Response Transfer Data
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                Len
                                              
                                                76
                                              
                                                TREP
                                              
                                                Data
                                              
                                                CS
                                             

                                                Request Transfer Exit
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                01
                                              
                                                37
                                                
                                                96
                                             

                                                Positive Response Request Transfer Exit
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                01
                                              
                                                77
                                                
                                                D6
                                             

                                                Stop Communication Request
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                01
                                              
                                                82
                                                
                                                E1
                                             

                                                Positive Response Stop Communication
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                01
                                              
                                                C2
                                                
                                                21
                                             

                                                Acknowledge sub message
                                              
                                                80
                                              
                                                EE
                                              
                                                F0
                                              
                                                Len
                                              
                                                83
                                               
                                                Data
                                              
                                                CS
                                             

                                                Negative responses
                                              

                                                General reject
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                10
                                              
                                                CS
                                             

                                                Service not supported
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                11
                                              
                                                CS
                                             

                                                Sub function not supported
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                12
                                              
                                                CS
                                             

                                                Incorrect Message Length
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                13
                                              
                                                CS
                                             

                                                Conditions not correct or Request sequence error
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                22
                                              
                                                CS
                                             

                                                Request out of range
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                31
                                              
                                                CS
                                             

                                                Upload not accepted
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                50
                                              
                                                CS
                                             

                                                Response pending
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                78
                                              
                                                CS
                                             

                                                Data not available
                                              
                                                80
                                              
                                                F0
                                              
                                                EE
                                              
                                                03
                                              
                                                7F
                                              
                                                Sid Req
                                              
                                                FA
                                              
                                                CS

— TRTP 21 to 25 are used for Generation 2 type of VU data download requests, TRTP 01 to 05 are used for Generation 1 type of VU data download requests, which can only be accepted by the VU in the frame of drivers' control performed by a non EU control authority, using a first generation control card.
— TRTP 11 to 19 and 31 to 39 are reserved for manufacturer specific download requests.
— Sid Req = the Sid of the corresponding request.
— TREP = the TRTP of the corresponding request.
— Dark cells denote that nothing is transmitted.
— The term upload (as seen from the IDE) is used for compatibility with ISO 14229. It means the same as download (as seen from the VU).
— Potential 2-byte sub message counters are not shown in this table.
— Slot is the slot number, either “1” (card on driver slot) or “2” (card on co-driver slot)
— In case the slot is not specified, the VU shall select slot 1 if a card is inserted in this slot and it shall select slot 2 only in case it is specifically selected by the user. 2.2.2.1  DDP_005 This message is issued by the IDE to establish the communication link with the VU. Initial communications are always performed at 9 600 baud (until baud rate is eventually changed using the appropriate Link control services).
 2.2.2.2  DDP_006 This message is issued by the VU to answer positively to a start communication request. It includes the 2 key bytes ‘EA’‘8F’ indicating that the unit supports protocol with header including target source and length information.
 2.2.2.3  DDP_007 The Start Diagnostic Session request message is issued by the IDE in order to request a new diagnostic session with the VU. The sub function ‘default session’ (81 Hex) indicates a standard diagnostic session is to be opened.
 2.2.2.4  DDP_008 The Positive Response Start Diagnostic message is sent by the VU to answer positively to Diagnostic Session Request.
 2.2.2.5  DDP_052 The Link Control Service is used by the IDE to initiate a change in baud rate. This takes place in two steps. In step one the IDE proposes the baud rate change, indicating the new rate. On receipt of a positive message from the VU the IDE sends out confirmation of the baud rate change to the VU (step two). The IDE then changes to the new baud rate. After receipt of the confirmation the VU changes to the new baud rate
 2.2.2.6  DDP_053 The Link Control Positive Response is issued by the VU to answer positively to Link Control Service request (step one). Note that no response is given to the confirmation request (step two).
 2.2.2.7  DDP_009 The Request Upload message is issued by the IDE to specify to the VU that a download operation is requested. To meet the requirements of ISO14229 data is included covering address, the size and format details for the data requested. As these are not known to the IDE prior to a download, the memory address is set to 0, format is unencrypted and uncompressed and the memory size is set to the maximum.
 2.2.2.8  DDP_010 The Positive Response Request Upload message is sent by the VU to indicate to the IDE that the VU is ready to download data. To meet the requirements of ISO 14229 data is included in this positive response message, indicating to the IDE that further Positive Response Transfer Data messages will include 00FF hex bytes maximum.
 2.2.2.9  DDP_011 
There are six types of data transfer. For VU data download, two different TRTP values can be used for each transfer type:


                                                   Data transfer type
                                                 
                                                   TRTP value for generation 1 type of VU data download
                                                 
                                                   TRTP value for generation 2 type of VU data download
                                                

                                                   Overview
                                                 
                                                   01
                                                 
                                                   21
                                                

                                                   Activities of a specified date
                                                 
                                                   02
                                                 
                                                   22
                                                

                                                   Events and faults
                                                 
                                                   03
                                                 
                                                   23
                                                

                                                   Detailed speed
                                                 
                                                   04
                                                 
                                                   24
                                                

                                                   Technical data
                                                 
                                                   05
                                                 
                                                   25
                                                
                                                   Data transfer type
                                                 
                                                   TRTP value
                                                

                                                   Card download
                                                 
                                                   06 DDP_054 
In the second case (TRTP 02 or 22) the Transfer Data Request message includes the indication of the calendar day (  format) to be downloaded.
 2.2.2.10  DDP_012 The Positive Response Transfer Data is sent by the VU in response to the Transfer Data Request. The message contains the requested data, with a Transfer Response Parameter (TREP) corresponding to the TRTP of the request.
 DDP_055 

— Security certificates,
— Vehicle identification,
— VU current date and time,
— Min and Max downloadable date (VU data),
— Indication of cards presence in the VU,
— Previous download to a company,
— Company locks,
— Previous controls.
 2.2.2.11  DDP_013 The Request Transfer Exit message is sent by the IDE to inform the VU that the download session is terminated.
 2.2.2.12  DDP_014 The Positive Response Request Transfer Exit message is sent by the VU to acknowledge the Request Transfer Exit.
 2.2.2.13  DDP_015 The Stop Communication Request message is sent by the IDE to disconnect the communication link with the VU.
 2.2.2.14  DDP_016 The Positive Response Stop Communication message is sent by the VU to acknowledge the Stop Communication Request.
 2.2.2.15  DDP_017 

— MsgC+1 Acknowledges correct receipt of sub message number MsgC.
Request from the IDE to the VU to send next sub message
— MsgC indicates a problem with the receipt of sub message number MsgC.
Request from the IDE to the VU to send the sub message again.
— FFFF requests termination of the message.
This can be used by the IDE to end the transmission of the VU message for any reason.

The last sub message of a message (LEN byte < 255) may be acknowledged using any of these codes or not acknowledged.

The VU responses that will consist of several sub messages are:


— Positive Response Transfer Data (SID 76)
 2.2.2.16  DDP_018 

— 10 general reject
The action cannot be performed for a reason not covered below.
— 11 service not supported
The SID of the request is not understood.
— 12 sub function not supported
The DS_ or TRTP of the request is not understood, or there are no further sub messages to be transmitted.
— 13 incorrect message length
The length of the received message is wrong.
— 22 conditions not correct or request sequence error
The required service is not active or the sequence of request messages is not correct.
— 31 Request out of range
The request parameter record (data field) is not valid.
— 50 upload not accepted
The request cannot be performed (VU in a non appropriate mode of operation or internal fault of the VU).
— 78 response pending
The action requested cannot be completed in time and the VU is not ready to accept another request.
— FA data not available
The data object of a data transfer request are not available in the VU (e.g. no card is inserted, generation 1 type of VU data download requested outside the frame of a driver’s control by a non EU control authority…).
 2.2.3 
A typical message flow during a normal data download procedure is the following:


IDE  VU
Start Communication Request ⇨ 
 ⇦ Positive Response
Start Diagnostic Service Request ⇨ 
 ⇦ Positive Response
Request Upload ⇨ 
 ⇦ Positive Response
Transfer Data Request Overview ⇨ 
 ⇦ Positive Response
Transfer Data Request #2 ⇨ 
 ⇦ Positive Response #1
Acknowledge Sub Message #1 ⇨ 
 ⇦ Positive Response #2
Acknowledge Sub Message #2 ⇨ 
 ⇦ Positive Response #m
Acknowledge Sub Message #m ⇨ 
 ⇦ Positive Response (Data Field < 255 Bytes)
Acknowledge Sub Message (optional) ⇨ 
…
Transfer Data Request #n ⇨ 
 ⇦ Positive Response
Request Transfer Exit ⇨ 
 ⇦ Positive Response
Stop Communication Request ⇨ 
 ⇦ Positive Response
 2.2.4  DDP_019 
Figure 1
Where:

P1Inter byte time for VU response.P2Time between end of IDE request and start of VU response, or between end of IDE acknowledge and start of next VU response.P3Time between end of VU response and start of new IDE request, or between end of VU response and start of IDE acknowledge, or between end of IDE request and start of new IDE request if VU fails to respond.P4Inter byte time for IDE request.P5Extended value of P3 for card downloading.

The allowed values for the timing parameters are showed in the following table (KWP extended timing parameters set, used in case of physical addressing for faster communication).


Timing Parameter Lower limitValue (ms) Upper limitValue (ms)
P1 0 20
P2 20 1 000
P3 10 5 000
P4 5 20
P5 10 20 minutes

 2.2.5 
If an error occurs during the message exchange, the message flow scheme is modified depending on which equipment has detected the error and on the message generating the error.

In figure 2 and figure 3 the error handling procedures for the VU and the IDE are respectively shown.
 2.2.5.1  DDP_020 If the IDE detects an error during the Start Communication phase, either by timing or by the bit stream, then it will wait for a period P3 min before issuing again the request.
 DDP_021 If the VU detects an error in the sequence coming from the IDE, it shall send no response and wait for another Start Communication Request message within a period P3 max.
 2.2.5.2 
Two different error handling areas can be defined:


1.. The VU detects an IDE transmission error.

DDP_022 For every received message the VU shall detect timing errors, byte format errors (e.g. start and stop bit violations) and frame errors (wrong number of bytes received, wrong checksum byte).
DDP_023 If the VU detects one of the above errors, then it sends no response and ignores the message received.
DDP_024 The VU may detect other errors in the format or content of the received message (e.g. message not supported) even if the message satisfies the length and checksum requirements; in such a case, the VU shall respond to the IDE with a Negative Response message specifying the nature of the error.
Figure 2
2.. The IDE detects a VU transmission error.

DDP_025 For every received message the IDE shall detect timing errors, byte format errors (e.g. start and stop bit violations) and frame errors (wrong number of bytes received, wrong checksum byte).
DDP_026 The IDE shall detect sequence errors, e.g. incorrect sub message counter increments in successive received messages.
DDP_027 If the IDE detects an error or there was no response from the VU within a P2 max period, the request message will be sent again for a maximum of three transmissions in total. For the purposes of this error detection a sub message acknowledge will be considered as a request to the VU.
DDP_028 The IDE shall wait at least for a period of P3 min before beginning each transmission; the wait period shall be measured from the last calculated occurrence of a stop bit after the error was detected.
Figure 3
 2.2.6 
This paragraph specifies the content of the data fields of the various positive response messages.

Data elements are defined in Appendix 1 data dictionary.
Remark: For generation 2 downloads, each top-level data element is represented by a record array, even if it contains only one record. A record array starts with a header; this header contains the record type, the record size and the number of records. Record arrays are named by ‘…RecordArray’ (with header) in the following tables. 2.2.6.1  DDP_029 

Data structure generation 1 (TREP 01 Hex)
Data element  Comment
 VU Security certificates
 Vehicle identification
 VU current date and time
 Downloadable period
 Type of cards inserted in the VU
 Previous VU download
 All company locks stored. If the section is empty, only noOfLocks = 0 is sent.
 All control records stored in the VU. If the section is empty, only noOfControls = 0 is sent
 RSA signature of all data (except certificates) starting from VehicleIdentificationNumber down to last byte of last VuControlActivityData.
Data structure generation 2 (TREP 21 Hex)
Data element  Comment
 Member state certificate
 VU certificate
 Vehicle identification
 Vehicle registration number
 VU current date and time
 Downloadable period
 Type of cards inserted in the VU
 Previous VU download
 All company locks stored. If the section is empty, an array header with noOfRecords = 0 is sent
 All control records stored in the VU. If the section is empty, an array header with noOfRecords = 0 is sent
 ECC signature of all preceding data except the certificates. 2.2.6.2  DDP_030 

Data structure generation 1 (TREP 02 Hex)
Data element  Comment
 Date of day downloaded
 Odometer at end of downloaded day
 Cards insertion withdrawal cycles data.
— If this section contains no available data, only noOfVuCardIWRecords = 0 is sent.
— When a VuCardIWRecord lies across 00:00 (card insertion on previous day) or across 24:00 (card withdrawal the following day) it shall appear in full within the two days involved.
 Slots status at 00:00 and activity changes recorded for the day downloaded.
 Places related data recorded for the day downloaded. If the section is empty, only noOfPlaceRecords = 0 is sent.
 Specific conditions data recorded for the day downloaded. If the section is empty, only noOfSpecificConditionRecords=0 is sent
 RSA signature of all data starting from TimeReal down to last byte of last specific condition record.
Data structure generation 2 (TREP 22 Hex)
Data element  Comment
 Date of day downloaded
 Odometer at end of downloaded day
 Cards insertion withdrawal cycles data.
— If this section contains no available data, an array header with noOfRecords = 0 is sent.
— When a VuCardIWRecord lies across 00:00 (card insertion on previous day) or across 24:00 (card withdrawal the following day) it shall appear in full within the two days involved.
 Slots status at 00:00 and activity changes recorded for the day downloaded.
 Places related data recorded for the day downloaded. If the section is empty, an array header with noOfRecords = 0 is sent.
 
                                                   GNSS positions of the vehicle when the accumulated driving time of the vehicle reaches a multiple of three hours. If the section is empty, an array header with noOfRecords = 0 is sent.
 Specific conditions data recorded for the day downloaded. If the section is empty, an array header with noOfRecords =0 is sent
 ECC signature of all preceding data. 2.2.6.3  DDP_031 

Data structure generation 1 (TREP 03 Hex)
Data element  Comment
 All faults stored or on-going in the VU.If the section is empty, only noOfVuFaults = 0 is sent.
 All events (except over speeding) stored or on-going in the VU.If the section is empty, only noOfVuEvents = 0 is sent.
 Data related to last over speeding control (default value if no data).
 All over speeding events stored in the VU.If the section is empty, only noOfVuOverSpeedingEvents = 0 is sent.
 All time adjustment events stored in the VU (outside the frame of a full calibration).If the section is empty, only noOfVuTimeAdjRecords = 0 is sent.
 RSA signature of all data starting from noOfVuFaults down to last byte of last time adjustment record
Data structure generation 2 (TREP 23 Hex)
Data element  Comment
 All faults stored or on-going in the VU.If the section is empty, an array header with noOfRecords = 0 is sent.
 All events (except over speeding) stored or on-going in the VU.If the section is empty, an array header with noOfRecords = 0 is sent.
 Data related to last over speeding control (default value if no data).
 All over speeding events stored in the VU.If the section is empty, an array header with noOfRecords = 0 is sent.
 All time adjustment events stored in the VU (outside the frame of a full calibration).If the section is empty, an array header with noOfRecords = 0 is sent.

 ECC signature of all preceding data. 2.2.6.4  DDP_032 

Data structure generation 1 (TREP 04)
Data element  Comment
 All detailed speed stored in the VU (one speed block per minute during which the vehicle has been moving)60 speed values per minute (one per second).
 RSA signature of all data starting from noOfSpeedBlocks down to last byte of last speed block.
Data structure generation 2 (TREP 24)
Data element  Comment
 All detailed speed stored in the VU (one speed block per minute during which the vehicle has been moving)60 speed values per minute (one per second).
 ECC signature of all preceding data. 2.2.6.5  DDP_033 

Data structure generation 1 (TREP 05)
Data element  Comment
 
 
 All calibration records stored in the VU.
 RSA signature of all data starting from vuManufacturerName down to last byte of last VuCalibrationRecord.
Data structure generation 2 (TREP 25)
Data element  Comment
 
 All MS pairings stored in the VU
 All external GNSS facility couplings stored in the VU
 All calibration records stored in the VU.
 All card insertion data stored in the VU.
 
 
 ECC signature of all preceding data. 2.3.  DDP_034 When a download session has included a VU data transfer, the IDE shall store within one single physical file all data received from the VU during the download session within Positive Response Transfer Data messages. Data stored excludes message headers, sub-message counters, empty sub-messages and checksums but include the SID and TREP (of the first sub-message only if several sub-messages).
 3.  3.1. 
This paragraph describes the direct card data downloading of a tachograph card to an IDE. The IDE is not part of the secure environment; therefore no authentication between the card and the IDE is performed.
 3.2. 
Download sessionEach time a download of the ICC data is performed. The session covers the complete procedure from the reset of the ICC by an IFD until the deactivation of the ICC (withdraw of the card or next reset).Signed Data FileA file from the ICC. The file is transferred to the IFD in plain text. On the ICC the file is hashed and signed and the signature is transferred to the IFD.
 3.3.  DDP_035 

— Download the common information of the card in the EFs  and  This information is optional and is not secured with a digital signature.
— (for first and second generation tachograph cards) Download EFs within  :
— Download the EFs  and  This information is not secured with a digital signature.
It is mandatory to download these files for each download session.
— Download the other application data EFs (within  ) except EF  . This information is secured with a digital signature, using Appendix 11 Common Security Mechanisms Part A.
— It is mandatory to download at least the EFs  and  for each download session.
— When downloading a driver card it is also mandatory to download the following EFs:

— (for second generation tacograph cards only) Except when a download of a driver card inserted in a VU is performed during drivers' control by a non EU control authority, using a first generation control card, download EFs within  :
— Download the EFs CardSignCertificate, CA_Certificate and Link_Certificate (if present). This information is not secured with a digital signature.
It is mandatory to download these files for each download session.
— Download the other application data EFs (within  ) except EF  . This information is secured with a digital signature, using Appendix 11 Common Security Mechanisms Part B.
— It is mandatory to download at least the EFs  and  for each download session.
— When downloading a driver card it is also mandatory to download the following EFs:

— When downloading a driver card, update the  date in EF  , in the  and, if applicable,  DFs.
— When downloading a workshop card, reset the calibration counter in EF  in the  and, if applicable,  DFs.
— When downloading a workshop card the EF  in the  and, if applicable,  DFs shall not be downloaded.
 3.3.1  DDP_036 
Card Direction IDE/IFD Meaning/Remarks
 ⇦ Hardware reset 
ATR ⇨  
It is optional to use PPS to switch to a higher baud rate as long as the ICC supports it.
 3.3.2  DDP_037 
Card Direction IDE/IFD Meaning/Remarks
 ⇦ Select File Select by File identifiers
OK ⇨  
 ⇦ Read Binary If the file contains more data than the buffer size of the reader or the card the command has to be repeated until the complete file is read.
File DataOK ⇨ Store data to ESM according to 3.4 Data storage formatNote 1: Before selecting the Card_Certificate (or CardSignCertificate) EF, the Tachograph Application must be selected (selection by AID).Note 2: Selecting and reading a file may also be performed in one step using a Read Binary command with a short EF identifier. 3.3.3  DDP_038 
Card
                                              
                                                Dir
                                              
                                                IDE / IFD
                                              
                                                Meaning / Remarks
                                             
  
                                                   Select File
                                                 

                                                   OK
                                                   
  
                                                   Perform Hash of File
                                                  — Calculates the hash value over the data content of the selected file using the prescribed hash algorithm in accordance with Appendix 11, part A or B. This command is not an ISO-Command.


                                                Calculate Hash of File and store Hash value temporarily
                                                

                                                   OK
                                                   
  
                                                   Read Binary
                                                 
                                                If the file contains more data than the buffer of the reader or the card can hold, the command has to be repeated until the complete file is read.
                                             

                                                         File Data
                                                      
                                                         OK
                                                        
                                                Store received data to ESM
                                              
                                                according to 
                                                
                                                   3.4
                                                
                                                 Data storage format
                                             
  
                                                   PSO: Compute Digital Signature
                                                 

                                                Perform Security Operation 
                                                ‘
                                                Compute Digital Signature
                                                ’
                                                 using the temporarily stored Hash value
                                                

                                                         Signature
                                                      
                                                         OK
                                                        
                                                Append data to the previous stored data on the ESM
                                              
                                                according to 
                                                
                                                   3.4
                                                
                                                 Data storage formatNote: Selecting and reading a file may also be performed in one step using a Read Binary command with a short EF identifier. In this case the EF may be selected and read before the command Perform Hash of File is applied. 3.3.4  DDP_039 
Card Dir IDE/IFD Meaning/Remarks
 ⇦ Select File EF Card_Download Select by File identifiers
OK ⇨  
 ⇦ Update BinaryNoOfCalibrationsSinceDownload = ‘00 00’ 
resets card download number   
OK ⇨  Note: Selecting and updating a file may also be performed in one step using an Update Binary command with a short EF identifier. 3.4.  3.4.1  DDP_040 

— The data shall be stored transparent. This means that the order of the bytes as well as the order of the bits inside the byte that are transferred from the card has to be preserved during storage.
— All files of the card downloaded within a download session are stored in one file on the ESM.
 3.4.2  DDP_041 The file format is a concatenation of several TLV objects.
 DDP_042 The tag for an EF shall be the FID plus the appendix „00“.
 DDP_043 The tag of an EF's signature shall be the FID of the file plus the appendix „01“.
 DDP_044 The length is a two byte value. The value defines the number of bytes in the value field. The value „FF FF“ in the length field is reserved for future use.
 DDP_045 When a file is not downloaded nothing related to the file shall be stored (no tag and no zero length).
 DDP_046 

                                                Definition
                                              
                                                Meaning
                                              
                                                Length
                                             

                                                FID (2 Bytes) || 
                                                ‘
                                                00
                                                ’
                                              
                                                Tag for EF (FID) in the 
                                                
                                                 or for common information of the card
                                              
                                                3 Bytes
                                             

                                                FID (2 Bytes) || 
                                                ‘
                                                01
                                                ’
                                              
                                                Tag for Signature of EF (FID) in the 
                                                
                                                 DF
                                              
                                                3 Bytes
                                             

                                                FID (2 Bytes) || 
                                                ‘
                                                02
                                                ’
                                              
                                                Tag for EF (FID) in the 
                                                
                                                 DF
                                              
                                                3 Bytes
                                             

                                                FID (2 Bytes) || 
                                                ‘
                                                03
                                                ’
                                              
                                                Tag for Signature of EF (FID) in the 
                                                
                                                 DF
                                              
                                                3 Bytes
                                             

                                                xx xx
                                              
                                                Length of Value field
                                              
                                                2 Bytes
                                             
Example of data in a download file on an ESM:


                                                Tag
                                              
                                                Length
                                              
                                                Value
                                             
   — Data of EF ICC

   — Data of EF Card_Certificate

   — …

  
                                                Data of EF 
                                                
                                                 (in the 
                                                
                                                 DF)
                                             
  
                                                Signature of EF 
                                                
                                                 (in the 
                                                
                                                 DF)
                                             
  
                                                Data of EF 
                                                
                                                 in the 
                                                
                                                 DF
                                             
  
                                                Signature of EF 
                                                
                                                 in the 
                                                
                                                 DF 4.  DDP_047 The VU must allow for downloading the content of a driver card inserted to a connected IDE.
 DDP_048 The IDE shall send a ‘Transfer Data Request Card Download’ message to the VU to initiate this mode (see 2.2.2.9).
 DDP_049 
Second generation driver cards: the VU shall then download the whole card, file by file, in accordance with the card downloading protocol defined in paragraph 3, and forward all data received from the card to the IDE within the appropriate TLV file format (see 3.4.2) and encapsulated within a ‘Positive Response Transfer Data’ message.
 DDP_050 The IDE shall retrieve card data from the ‘Positive Response Transfer Data’ message (stripping all headers, SIDs, TREPs, sub message counters, and checksums) and store them within one single physical file as described in paragraph 2.3.
 DDP_051 The VU shall then, as applicable, update the  or the  file of the driver card.

Appendix 8 1. 
This appendix describes how data is exchanged between a vehicle unit and a tester via the K-line which forms part of the calibration interface described in Appendix 6. It also describes control of the input/output signal line on the calibration connector.

Establishing K-line communications is described in Section 4 ‘Communication Services’.

This appendix uses the idea of diagnostic ‘sessions’ to determine the scope of K-line control under different conditions. The default session is the ‘StandardDiagnosticSession’ where all data can be read from a vehicle unit but no data can be written to a vehicle unit.

Selection of the diagnostic session is described in Section 5 ‘Management Services’.

This appendix has to be considered as relevant for both generations of VUs and of workshop cards, in compliance with the interoperability requirements laid down in this Regulation.
 CPR_001 
Data transfer via K-line is described in Section 6 ‘Data Transmission Services’. Formats of data transferred are detailed in Section 8 ‘dataRecords formats’.
 CPR_002 The ‘ECUAdjustmentSession’ allows the selection of the I/O mode of the calibration I/O signal line via the K-line interface. Control of the calibration I/O signal line is described in section 7 ‘Control of Test Pulses — Input/Output Control functional unit’.
 CPR_003 Throughout this document the address of the tester is referred to as ‘tt’. Although there may be preferred addresses for testers, the VU shall respond correctly to any tester address. The physical address of the VU is 0xEE.
 2. 
The protocols, messages and error codes are principally based on a draft of ISO 14229-1 (Road vehicles — Diagnostic systems — Part 1: Diagnostic services, version 6 of 22 February 2001).

Byte encoding and hexadecimal values are used for the service identifiers, the service requests and responses, and the standard parameters.

The term ‘tester’ refers to the equipment used to enter programming/calibration data into the VU.

The terms ‘client’ and ‘server’ refer to the tester and the VU respectively.

The term ECU means ‘Electronic Control Unit’ and refers to the VU.

ISO 14230-2: Road Vehicles -Diagnostic Systems — Keyword Protocol 2000- Part 2: Data Link Layer.

First edition: 1999.
 3.  3.1. 
The following table provides an overview of the services that will be available in the tachograph and are defined in this document.
 CPR_004 

— The 1st column lists the services that are available.
— The 2nd column includes the section number in this appendix where of service is further defined.
— The 3rd column assigns the service identifier values for request messages.
— The 4th column specifies the services of the ‘StandardDiagnosticSession’ (SD) which must be implemented in each VU.
— The 5th column specifies the services of the ‘ECUAdjustmentSession’ (ECUAS) which must be implemented to allow control of the I/O signal line in the front panel calibration connector of the VU.
— The 6th column specifies the services of the ‘ECUProgrammingSession’ (ECUPS) which must be implemented to allow for programming of parameters in the VU.


 Diagnostic Sessions
Diagnostic Service Name Section No. SId Req.Value SD ECUAS ECUPS
StartCommunication 4.1 81 ■ ■ ■
StopCommunication 4.2 82 ■  
TesterPresent 4.3 3E ■ ■ ■
StartDiagnosticSession 5.1 10 ■ ■ ■
SecurityAccess 5.2 27 ■ ■ ■
ReadDataByIdentifier 6.1 22 ■ ■ ■
WriteDataByIdentifier 6.2 2E   ■
InputOutputControlByIdentifier 7.1 2F  ■ 
■This symbol indicates that the service is mandatory in this diagnostic session.
No symbol indicates that this service is not allowed in this diagnostic session.
 3.2. 
Response codes are defined for each service.
 4. 
Some services are necessary to establish and maintain communication. They do not appear on the application layer. The services available are detailed in the following table:


Service name Description
StartCommunication The client requests to start a communication session with a server(s).
StopCommunication The client requests to stop the current communication session.
TesterPresent The client indicates to the server that it is still present.
 CPR_005 The StartCommunication Service is used for starting a communication. In order to perform any service, communication must be initialised and the communication parameters need to be appropriate for the desired mode.
 4.1.  CPR_006 Upon receiving a StartCommunication indication primitive, the VU shall check if the requested communication link can be initialised under the present conditions. Valid conditions for the initialisation of a communication link are described in document ISO 14230-2.
 CPR_007 Then the VU shall perform all actions necessary to initialise the communication link and send a StartCommunication response primitive with the Positive Response parameters selected.
 CPR_008 If a VU that is already initialised (and has entered any diagnostic session) receives a new StartCommunication Request (e.g. due to error recovery in the tester) the request shall be accepted and the VU shall be reinitialised.
 CPR_009 If the communication link cannot be initialised for any reason, the VU shall continue operating as it was immediately prior to the attempt to initialise the communication link..
 CPR_010 The StartCommunication Request message must be physically addressed.
 CPR_011 

— There is a bus-idle time prior to any activity.
— The tester then sends an initialisation pattern.
— All information which is necessary to establish communication is contained in the response of the VU.
 CPR_012 

— All communication parameters are set to values defined in Table 4 according to the key bytes.
— The VU is waiting for the first request of the tester.
— The VU is in the default diagnostic mode, i.e. StandardDiagnosticSession.
— The calibration I/O signal line is in the default state, i.e. disabled state.
 CPR_014 The data rate on the K-line shall be 10 400 Baud.
 CPR_016 

 CPR_017 

— First transmission after power on, Tidle = 300 ms.
— After completion of a StopCommunication Service, Tidle = P3 min.
— After stopping communication by time-out P3 max, Tidle = 0.


Table 3
Timing values for fast initialisation
Parameter min value max value
Tinil 25 ± 1 ms 24 ms 26 ms
Twup 50 ± 1 ms 49 ms 51 ms
Table 4
Communication timing values
Timing Parameter Parameter Description lower limit values [ms] upper limit values [ms]
min. max.
P1 Inter byte time for VU response 0 20
P2 Time between tester request and VU response or two VU responses 25 250
P3 Time between end of VU responses and start of new tester request 55 5 000
P4 Inter byte time for tester request 5 20 CPR_018 

Table 5
StartCommunication Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 81 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 StartCommunication Request Service Id 81 SCR
#5 Checksum 00-FF CS
Table 6
StartCommunication Positive Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 StartCommunication Positive Response Service Id C1 SCRPR
#6 Key byte 1 EA KB1
#7 Key byte 2 8F KB2
#8 Checksum 00-FF CS CPR_019 There is no negative response to the StartCommunication Request message, if there is no positive response message to be transmitted then the VU is not initialised, nothing is transmitted and it remains in its normal operation.
 4.2.  4.2.1 
The purpose of this communication layer service is to terminate a communication session.
 CPR_020 Upon receiving a StopCommunication indication primitive, the VU shall check if the current conditions allow to terminate this communication. In this case the VU shall perform all actions necessary to terminate this communication.
 CPR_021 If it is possible to terminate the communication, the VU shall issue a StopCommunication response primitive with the Positive Response parameters selected, before the communication is terminated.
 CPR_022 If the communication cannot be terminated by any reason, the VU shall issue a StopCommunication response primitive with the Negative Response parameter selected.
 CPR_023 If time-out of P3 max is detected by the VU, the communication shall be terminated without any response primitive being issued.
 4.2.2  CPR_024 

Table 7
StopCommunication Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte 01 LEN
#5 StopCommunication Request Service Id 82 SPR
#6 Checksum 00-FF CS
Table 8
StopCommunication Positive Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 01 LEN
#5 StopCommunication Positive Response Service Id C2 SPRPR
#6 Checksum 00-FF CS
Table 9
StopCommunication Negative Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 negative Response Service Id 7F NR
#6 StopCommunication Request Service Identification 82 SPR
#7 responseCode = generalReject 10 RC_GR
#8 Checksum 00-FF CS 4.2.3 
This service does not require any parameter definition.
 4.3.  4.3.1 
The TesterPresent service is used by the tester to indicate to the server that it is still present, in order to prevent the server from automatically returning to normal operation and possibly stopping the communication. This service, sent periodically, keeps the diagnostic session/communication active by resetting the P3 timer each time a request for this service is received.
 4.3.2  CPR_079 

Table 10
TesterPresent Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte 02 LEN
#5 TesterPresent Request Service Id 3E TP
#6 Sub Function = responseRequired = [ yes 01 RESPREQ_Y
no ] 02 RESPREQ_NO
#7 Checksum 00-FF CS CPR_080 

Table 11
TesterPresent Positive Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 01 LEN
#5 TesterPresent Positive Response Service Id 7E TPPR
#6 Checksum 00-FF CS CPR_081 

Table 12
TesterPresent Negative Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 negative Response Service Id 7F NR
#6 TesterPresent Request Service Identification 3E TP
#7 responseCode = [SubFunctionNotSupported-InvalidFormat 12 RC_SFNS_IF
incorrectMessageLength] 13 RC_IML
#8 Checksum 00-FF CS 5. 
The services available are detailed in the following table:


Service name Description
StartDiagnosticSession The client requests to start a diagnostic session with a VU.
SecurityAccess The client requests access to functions restricted to authorised users.
 5.1.  5.1.1  CPR_025 

— There shall be always exactly one diagnostic session active in the VU,
— The VU shall always start the StandardDiagnosticSession when powered up. If no other diagnostic session is started, then the StandardDiagnosticSession shall be running as long as the VU is powered,
— If a diagnostic session which is already running has been requested by the tester, then the VU shall send a positive response message,
— Whenever the tester requests a new diagnostic session, the VU shall first send a StartDiagnosticSession positive response message before the new session becomes active in the VU. If the VU is not able to start the requested new diagnostic session, then it shall respond with a StartDiagnosticSession negative response message, and the current session shall continue.
 CPR_026 A diagnostic session shall only be started if communication has been established between the client and the VU.
 CPR_027 The timing parameters defined in Table 4 shall be active after a successful StartDiagnosticSession with the diagnosticSession parameter set to ‘StandardDiagnosticSession’ in the request message if another diagnostic session was previously active.
 5.1.2  CPR_028 

Table 14
StartDiagnosticSession Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte 02 LEN
#5 StartDiagnosticSession Request Service Id 10 STDS
#6 diagnosticSession = [one value from Table 17] xx DS_…
#7 Checksum 00-FF CS
Table 15
StartDiagnosticSession Positive Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 02 LEN
#5 StartDiagnosticSession Positive Response Service Id 50 STDSPR
#6 diagnosticSession = [same value as in byte #6 Table 14] xx DS_…
#7 Checksum 00-FF CS
Table 16
StartDiagnosticSession Negative Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 Negative Response Service Id 7F NR
#6 StartDiagnosticSession Request Service Id 10 STDS
#7 ResponseCode = [subFunctionNotSupported 12 RC_SFNS
incorrectMessageLength 13 RC_IML
conditionsNotCorrect 22 RC_CNC
#8 Checksum 00-FF CS


 5.1.3  CPR_029 

Table 17
Definition of diagnosticSession Values
Hex Description Mnemonic
81 
This diagnostic session enables all services specified in Table 1 column 4 “SD”. These services allow reading of data from a server (VU). This diagnostic Session is active after the initialisation has been successfully completed between client (tester) and server (VU). This diagnostic session may be overwritten by other diagnostic sessions specified in this section.
 SD
85 
This diagnostic session enables all services specified in Table 1 column 6 “ECUPS”. These services support the memory programming of a server (VU) This diagnostic session may be overwritten by other diagnostic sessions specified in this section..
 ECUPS
87 
This diagnostic session enables all services specified in Table 1 column 5 “ECUAS”. These services support the input/output control of a server (VU). This diagnostic session may be overwritten by other diagnostic sessions specified in this section.
 ECUAS 5.2. 
Writing of calibration data is not possible unless the VU is in CALIBRATION mode. In addition to insertion of a valid workshop card into the VU, it is necessary to enter the appropriate PIN into the VU before access to the CALIBRATION mode is granted.

When the VU is in CALIBRATION or CONTROL mode, access to the calibration input/output line is also possible.

The SecurityAccess service provides a means to enter the PIN and to indicate to the tester whether or not the VU is in CALIBRATION mode.

It is acceptable that the PIN may be entered through alternative methods.
 5.2.1 
The SecurityAccess service consists of a SecurityAccess ‘requestSeed’ message, eventually followed by a SecurityAccess ‘sendKey’ message. The SecurityAccess service must be carried out after the StartDiagnosticSession service.
 CPR_033 The tester shall use the SecurityAccess ‘requestSeed’ message to check if the vehicle unit is ready to accept a PIN.
 CPR_034 If the vehicle unit is already in CALIBRATION mode, it shall answer the request by sending a ‘seed’ of 0x0000 using the service SecurityAccess Positive Response.
 CPR_035 If the vehicle unit is ready to accept a PIN for verification by a workshop card, it shall answer the request by sending a ‘seed’ greater than 0x0000 using the service SecurityAccess Positive Response.
 CPR_036 If the vehicle unit is not ready to accept a PIN from the tester, either because the workshop card inserted is not valid, or because no workshop card has been inserted, or because the vehicle unit expects the PIN from another method, it shall answer the request with a Negative Response with a response code set to conditionsNotCorrectOrRequestSequenceError.
 CPR_037 The tester shall then, eventually, use the SecurityAccess ‘sendKey’ message to forward a PIN to the Vehicle Unit. To allow time for the card authentication process to take place, the VU shall use the negative response code requestCorrectlyReceived-ResponsePending to extend the time to respond. However, the maximum time to respond shall not exceed 5 minutes. As soon as the requested service has been completed, the VU shall send a positive response message or negative response message with a response code different from this one. The negative response code requestCorrectlyReceived-ResponsePending may be repeated by the VU until the requested service is completed and the final response message is sent.
 CPR_038 The vehicle unit shall answer to this request using the service SecurityAccess Positive Response only when in CALIBRATION mode.
 CPR_039 

— subFunctionNot supported: Invalid format for the subfunction parameter (accessType),
— conditionsNotCorrectOrRequestSequenceError: Vehicle unit not ready to accept a PIN entry,
— invalidKey: PIN not valid and number of PIN checks attempts not exceeded,
— exceededNumberOfAttempts: PIN not valid and number of PIN checks attempts exceeded,
— generalReject: Correct PIN but mutual authentication with workshop card failed.
 5.2.2  CPR_040 

Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte 02 LEN
#5 SecurityAccess Request Service Id 27 SA
#6 accessType — requestSeed 7D AT_RSD
#7 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 04 LEN
#5 SecurityAccess Positive Response Service Id 67 SAPR
#6 accessType — requestSeed 7D AT_RSD
#7 Seed High 00-FF SEEDH
#8 Seed Low 00-FF SEEDL
#9 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 negativeResponse Service Id 7F NR
#6 SecurityAccess Request Service Id 27 SA
#7 responseCode = [conditionsNotCorrectOrRequestSequenceError 22 RC_CNC
incorrectMessageLength] 13 RC_IML
#8 Checksum 00-FF CS
 5.2.3  CPR_041 

Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte m+2 LEN
#5 SecurityAccess Request Service Id 27 SA
#6 accessType — sendKey 7E AT_SK
#7 to #m + 6 Key #1 (High) xx KEY
… … 
Key #m (low, m must be a minimum of 4, and a maximum of 8) xx 
#m + 7 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 02 LEN
#5 SecurityAccess Positive Response Service Id 67 SAPR
#6 accessType — sendKey 7E AT_SK
#7 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 NegativeResponse Service Id 7F NR
#6 SecurityAccess Request Service Id 27 SA
#7 ResponseCode = [generalReject 10 RC_GR
subFunctionNotSupported 12 RC_SFNS
incorrectMessageLength 13 RC_IML
conditionsNotCorrectOrRequestSequenceError 22 RC_CNC
invalidKey 35 RC_IK
exceededNumberOfAttempts 36 RC_ENA
requestCorrectlyReceived-ResponsePending] 78 RC_RCR_RP
#8 Checksum 00-FF CS
 6. 
The services available are detailed in the following table:


Service name Description
ReadDataByIdentifier The client requests the transmission of the current value of a record with access by recordDataIdentifier.
WriteDataByIdentifier The client requests to write a record accessed by recordDataIdentifier.
 6.1.  6.1.1  CPR_050 The ReadDataByIdentifier service is used by the client to request data record values from a server. The data are identified by a recordDataIdentifier. It is the VU manufacturer's responsibility that the server conditions are met when performing this service.
 6.1.2  CPR_051 

Table 25
ReadDataByIdentifier Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte 03 LEN
#5 ReadDataByIdentifier Request Service Id 22 RDBI
#6 to #7 recordDataIdentifier = [a value fromTable 28] xxxx RDI_…
#8 Checksum 00-FF CS
Table 26
ReadDataByIdentifier Positive Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte m+3 LEN
#5 ReadDataByIdentifier Positive Response Service Id 62 RDBIPR
#6 and #7 recordDataIdentifier = [the same value as bytes #6 and #7 Table 25] xxxx RDI_...
#8 to #m + 7 dataRecord[] = [data#1 xx DREC_DATA1
: : :
data#m] xx DREC_DATAm
#m + 8 Checksum 00-FF CS
Table 27
ReadDataByIdentifier Negative Response Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 NegativeResponse Service Id 7F NR
#6 ReadDataByIdentifier Request Service Id 22 RDBI
#7 ResponseCode= [requestOutOfRange 31 RC_ROOR
incorrectMessageLength 13 RC_IML
conditionsNotCorrect] 22 RC_CNC
#8 Checksum 00-FF CS 6.1.3  CPR_052 The parameter recordDataIdentifier (RDI_) in the ReadDataByIdentifier request message identifies a data record.
 CPR_053 
The recordDataIdentifier table consists of four columns and multiple lines.


— The 1st column (Hex) includes the ‘Hex Value’ assigned to the recordDataIdentifier specified in the 3rd column.
— The 2nd column (Data element) specifies the data element of Appendix 1 on which the recordDataIdentifier is based (transcoding is sometimes necessary).
— The 3rd column (Description) specifies the corresponding recordDataIdentifier name.
— The 4th column (Mnemonic) specifies the mnemonic of this recordDataIdentifier.


Table 28
Definition of recordDataIdentifier values
Hex Data element recordDataIdentifier Name(see format in Section 8.2) Mnemonic
F90B  TimeDate RDI_TD
F912  HighResolutionTotalVehicleDistance RDI_HRTVD
F918  Kfactor RDI_KF
F91C  LfactorTyreCircumference RDI_LF
F91D  WvehicleCharacteristicFactor RDI_WVCF
F921  TyreSize RDI_TS
F922  NextCalibrationDate RDI_NCD
F92C  SpeedAuthorised RDI_SA
F97D  RegisteringMemberState RDI_RMS
F97E  VehicleRegistrationNumber RDI_ VRN
F190  VIN RDI_ VIN CPR_054 The parameter dataRecord (DREC_) is used by the ReadDataByIdentifier positive response message to provide the data record value identified by the recordDataIdentifier to the client (tester). Data formats are specified in section 8. Additional user optional dataRecords including VU specific input, internal and output data may be implemented, but are not defined in this document.
 6.2.  6.2.1  CPR_056 The WriteDataByIdentifier service is used by the client to write data record values to a server. The data are identified by a recordDataIdentifier. It is the VU manufacturer's responsibility that the server conditions are met when performing this service. To update the parameters listed in Table 28 the VU must be in CALIBRATION mode.
 6.2.2  CPR_057 

Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte m + 3 LEN
#5 WriteDataByIdentifier Request Service Id 2E WDBI
#6 to #7 recordDataIdentifier = [a value from Table 28] xxxx RDI_…
#8 to m + 7 dataRecord[] = [data#1 xx DREC_DATA1
: : :
data#m] xx DREC_DATAm
#m + 8 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 WriteDataByIdentifier Positive Response Service Id 6E WDBIPR
#6 to #7 recordDataIdentifier = [the same value as bytes #6 and #7 Table 29] xxxx RDI_…
#8 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 NegativeResponse Service Id 7F NR
#6 WriteDataByIdentifier Request Service Id 2E WDBI
#7 ResponseCode= [requestOutOfRange 31 RC_ROOR
incorrectMessageLength 13 RC_IML
conditionsNotCorrect] 22 RC_CNC
#8 Checksum 00-FF CS
 6.2.3 
The parameter recordDataIdentifier (RDI_) is defined in Table 28.

The parameter dataRecord (DREC_) is used by the WriteDataByIdentifier request message to provide the data record values identified by the recordDataIdentifier to the server (VU). Data formats are specified in section 8.
 7. 
The services available are detailed in the following table:


Service name Description
InputOutputControlByIdentifier The client requests the control of an input/output specific to the server.
 7.1.  7.1.1 
There is a connection via the front connector which allows test pulses to be controlled or monitored using a suitable tester.
 CPR_058 

— disabled,
— speedSignalInput, where the calibration I/O signal line is used to input a speed signal (test signal) replacing the motion sensor speed signal, this function is not available in CONTROL mode,
— realTimeSpeedSignalOutputSensor, where the calibration I/O signal line is used to output the speed signal of the motion sensor,
— RTCOutput, where the calibration I/O signal line is used to output the UTC clock signal, this function is not available in CONTROL mode.
 CPR_059 The vehicle unit must have entered an adjustment session and must be in CALIBRATION or CONTROL mode to configure the state of the line. When the VU is in CALIBRATION mode, the four states of the line can be selected (disabled, speedSignalInput, realTimeSpeedSignalOutputSensor, RTCOutput). When the VU is in CONTROL mode, only two states of the lines can be selected (disabled, realTimeSpeedOutputSensor). On exit of the adjustment session or of the CALIBRATION or CONTROL mode the vehicle unit must ensure the calibration I/O signal line is returned to the ‘disabled’ (default) state.
 CPR_060 If speed pulses are received at the real time speed signal input line of the VU while the calibration I/O signal line is set to input then the calibration I/O signal line shall be set to output or returned to the disabled state.
 CPR_061 

— Establish communications by StartCommunication Service
— Enter an adjustment session by StartDiagnosticSession Service and be in CALIBRATION or CONTROL mode of operation (the order of these two operation is not important).
— Change the state of the output by InputOutputControlByIdentifier Service.
 7.1.2  CPR_062 

Table 33
InputOutputControlByIdentifier Request Message
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte EE TGT
#3 Source address byte tt SRC
#4 Additional length byte xx LEN
#5 InputOutputControlByIdentifier Request Sid 2F IOCBI
#6 and #7 InputOutputIdentifier = [CalibrationInputOutput] F960 IOI_CIO
#8 or#8 to #9 ControlOptionRecord = [  COR_…
inputOutputControlParameter — one value from Table 36 xx IOCP_…
controlState — one value from Table 37 (see note below)] xx CS_…
#9 or #10 Checksum 00-FF CSNote: The controlState parameter is present only in some cases (see 7.1.3).

Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte xx LEN
#5 inputOutputControlByIdentifier Positive Response SId 6F IOCBIPR
#6 and #7 inputOutputIdentifier = [CalibrationInputOutput] F960 IOI_CIO
#8 or#8 to #9 controlStatusRecord = [  CSR_
inputOutputControlParameter (same value as byte #8 Table 33) xx IOCP_…
controlState (same value as byte #9 Table 33)] (if applicable) xx CS_…
#9 or #10 Checksum 00-FF CS
Byte # Parameter Name Hex Value Mnemonic
#1 Format byte — physical addressing 80 FMT
#2 Target address byte tt TGT
#3 Source address byte EE SRC
#4 Additional length byte 03 LEN
#5 negativeResponse Service Id 7F NR
#6 inputOutputControlByIdentifier Request SId 2F IOCBI
#7 responseCode=[  
incorrectMessageLength 13 RC_IML
conditionsNotCorrect 22 RC_CNC
requestOutOfRange 31 RC_ROOR
deviceControlLimitsExceeded] 7A RC_DCLE
#8 Checksum 00-FF CS
 7.1.3  CPR_064 

Table 36
Definition of inputOutputControlParameter values
Hex Description Mnemonic
00 
This value shall indicate to the server (VU) that the tester does no longer have control about the calibration I/O signal line.
 RCTECU
01 
This value shall indicate to the server (VU) that it is requested to reset the calibration I/O signal line to its default state.
 RTD
03 
This value shall indicate to the server (VU) that it is requested to adjust the calibration I/O signal line to the value included in the controlState parameter.
 STA CPR_065 

Table 37
Definition of controlState values
Mode Hex Value Description
Disable 00 I/O line is disabled (default state)
Enable 01 Enable calibration I/O line as speedSignalInput
Enable 02 Enable calibration I/O line as realTimeSpeedSignalOutputSensor
Enable 03 Enable calibration I/O line as RTCOutput 8. 
This section details:


— general rules that shall be applied to ranges of parameters transmitted by the vehicle unit to the tester,
— formats that shall be used for data transferred via the Data Transmission Services described in section 6.
 CPR_067 All parameters identified shall be supported by the VU.
 CPR_068 Data transmitted by the VU to the tester in response to a request message shall be of the measured type (i.e. current value of the requested parameter as measured or observed by the VU).
 8.1.  CPR_069 Table 38 defines the ranges used to determine the validity of a transmitted parameter.
 CPR_070 The values in the range ‘error indicator’ provide a means for the vehicle unit to immediately indicate that valid parametric data is not currently available due to some type of error in the tachograph.
 CPR_071 The values in the range ‘not available’ provide a means for the vehicle unit to transmit a message which contains a parameter that is not available or not supported in that module. The values in the range ‘not requested’ provide a means for a device to transmit a command message and identify those parameters where no response is expected from the receiving device.
 CPR_072 

Table 38
dataRecords ranges
Range Name 1 byte(Hex value) 2 bytes(Hex value) 4 bytes(Hex Value) ASCII
Valid signal 00 to FA 0000 to FAFF 00000000 to FAFFFFFF 1 to 254
Parameter specific indicator FB FB00 to FBFF FB000000 to FBFFFFFF none
Reserved range for future indicator bits FC to FD FC00 to FDFF FC000000 to FDFFFFFF none
Error indicator FE FE00 to FEFF FE000000 to FEFFFFFF 0
Not available or not requested FF FF00 to FFFF FF000000 to FFFFFFFF FF CPR_073 For parameters coded in ASCII, the ASCII character ‘*’ is reserved as a delimiter.
 8.2. 
Table 39 to Table 42 below detail the formats that shall be used via the ReadDataByIdentifier and WriteDataByIdentifier Services.
 CPR_074 

Table 39
Format of dataRecords
Parameter Name Data length (bytes) Resolution Operating range
TimeDate 8 See details in Table 40
HighResolutionTotalVehicleDistance 4 5 m/bit gain, 0 m offset 0 to + 21 055 406 km
Kfactor 2 0,001 pulse/m/bit gain, 0 offset 0 to 64,255 pulse/m
LfactorTyreCircumference 2 0,125 10– 3 m/bit gain, 0 offset 0 to 8,031 m
WvehicleCharacteristicFactor 2 0,001 pulse/m/bit gain, 0 offset 0 to 64,255 pulse/m
TyreSize 15 ASCII ASCII
NextCalibrationDate 3 See details in Table 41
SpeedAuthorised 2 1/256 km/h/bit gain, 0 offset 0 to 250,996 km/h
RegisteringMemberState 3 ASCII ASCII
VehicleRegistrationNumber 14 See details in Table 42
VIN 17 ASCII ASCII CPR_075 

Table 40
Detailed format of TimeDate (recordDataIdentifier value # F90B)
Byte Parameter definition Resolution Operating range
1 Seconds 0,25 s/bit gain, 0 s offset 0 to 59,75 s
2 Minutes 1 min/bit gain, 0 min offset 0 to 59 min
3 Hours 1 h/bit gain, 0 h offset 0 to 23 h
4 Month 1 month/bit gain, 0 month offset 1 to 12 month
5 Day 0,25 day/bit gain, 0 day offset(see NOTE below Table 41) 0,25 to 31,75 day
6 Year 1 year/bit gain, + 1985 year offset(see NOTE below Table 41) 1985 to 2235 year
7 Local Minute Offset 1 min/bit gain, – 125 min offset – 59 to + 59 min
8 Local Hour Offset 1 h/bit gain, – 125 h offset – 23 to + 23 h CPR_076 

Table 41
Detailed format of NextCalibrationDate (recordDataIdentifier value # F922)
Byte Parameter definition Resolution Operating range
1 Month 1 month/bit gain, 0 month offset 1 to 12 month
2 Day 0,25 day/bit gain, 0 day offset(see NOTE below) 0,25 to 31,75 day
3 Year 1 year/bit gain, + 1985 year offset(see NOTE below) 1985 to 2235 yearNOTE concerning the use of the ‘Day’ parameter:
1)) A value of 0 for the date is null. The values 1, 2, 3, and 4 are used to identify the first day of the month; 5, 6, 7, and 8 identify the second day of the month; etc.
2)) This parameter does not influence or change the hours parameter above.NOTE concerning the use of byte ‘Year’ parameter:A value of 0 for the year identifies the year 1985; a value of 1 identifies 1986; etc. CPR_078 

Table 42
Detailed format of VehicleRegistrationNumber (recordDataIdentifier value # F97E)
Byte Parameter definition Resolution Operating range
1 Code Page (as defined in Appendix 1) ASCII 01 to 0A
2 - 14 Vehicle Registration Number (as defined in Appendix 1) ASCII ASCII
Appendix 9 1.  1.1. 
The EC type approval for a recording equipment (or component) or a tachograph card is based on:


— a 
                                             security certification
                                          , based on Common Criteria specifications, against a security target fully compliant with Appendix 10 to this Annex,
— a functional certification performed by a Member State authority certifying that the item tested fulfils the requirements of this Annex in terms of functions performed, measurement accuracy and environmental characteristics,
— an interoperability certification performed by the competent body certifying that the recording equipment (or tachograph card) is fully interoperable with the necessary tachograph card (or recording equipment) models (see Chapter 8 of this Annex).

This Appendix specifies which tests, as a minimum, must be performed by a Member State authority during the functional tests, and which tests, as a minimum, must be performed by the competent body during the interoperability tests. Procedures to follow to carry out the tests or the type of tests are not specified further.

The security certification aspects are not covered by this Appendix. If some tests requested for type approval are performed during the security evaluation and certification process, then these tests do not need to be performed again. In this case, only the results of these security tests may be inspected. For information, the requirements expected to be tested (or closely related to tests expected to be performed) during the security certification, are marked with a ‘*’ in this Appendix.

The numbered requirements refer to the Annex corpus, while the other requirements refer to the other appendixes (e.g. PIC_001 refers to requirement PIC_001 of Appendix 3 Pictograms).

This Appendix considers separately the type approval of the motion sensor, of the vehicle unit, and of the external GNSS facility as components of the recording equipment. Each component will get its own type approval certificate in which the other compatible components will be indicated. The functional test of the motion sensor (or external GNSS facility) is done together with the vehicle unit and vice versa.

Interoperability between every model of motion sensor (resp. external GNSS facility) and every model of vehicle unit is not required. In that case the type approval for a motion sensor (resp. external GNSS facility) can be granted only in combination with the type approval of the relevant vehicle unit and vice versa.
 1.2. 
The following references are used in this Appendix:

IEC 60068-2-1:Environmental testing — Part 2-1: Tests — Test A: ColdIEC 60068-2-2:Basic environmental testing procedures; part 2: tests; tests B: dry heat (sinusoidal).IEC 60068-2-6:Environmental testing — Part 2: Tests — Test Fc: VibrationIEC 60068-2-14:Environmental testing; Part 2-14: Tests; Test N: Change of temperatureIEC 60068-2-27:Environmental testing. Part 2: Tests. Test Ea and guidance: ShockIEC 60068-2-30:Environmental testing — Part 2-30: Tests — Test Db: Damp heat, cyclic (12 h + 12 h cycle)IEC 60068-2-64:Environmental testing — Part 2-64: Tests — Test Fh: Vibration, broadband random and guidanceIEC 60068-2-78Environmental testing — Part 2-78: Tests — Test Cab: Damp heat, steady stateISO 16750-3 —Mechanical loads (2012-12)ISO 16750-4 —Climatic loads(2010-04).ISO 20653:Road vehicles — Degree of protection (IP code) — Protection of electrical equipment against foreign objects, water and accessISO 10605:2008 + Technical Corrigendum:2010 + AMD1:2014Road vehicles — Test methods for electrical disturbances from electrostatic dischargeISO 7637-1:2002 + AMD1: 2008Road vehicles — Electrical disturbances from conduction and coupling — Part 1: Definitions and general considerations.ISO 7637-2Road vehicles — Electrical disturbances from conduction and coupling — Part 2: Electrical transient conduction along supply lines only.ISO 7637-3Road vehicles — Electrical disturbances from conduction and coupling — Part 3: Electrical transient transmission by capacitive and inductive coupling via lines other than supply lines.ISO/IEC 7816-1Identification cards — Integrated circuit(s) cards with contacts — Part 1: Physical characteristics..ISO/IEC 7816-2Information technology — Identification cards — Integrated circuit(s) cards with contacts — Part 2: Dimensions and location of the contacts.ISO/IEC 7816-3Information technology — Identification cards — Integrated circuit(s) cards with contacts — Part 3: Electronic signals and transmission protocol.ISO/IEC 10373-1:2006 + AMD1:2012Identification cards — Test methods — Part 1: General characteristicsISO/IEC 10373-3:2010 + Technical Corrigendum:2013Identification cards — Test methods — Part 3: Integrated circuit cards with contacts and related interface devicesISO 16844-3:2004, Cor 1:2006Road vehicles — Tachograph systems — Part 3: Motion sensor interface (with vehicle units).ISO 16844-4Road vehicles — Tachograph systems — Part 4: CAN interfaceISO 16844-6Road vehicles — Tachograph systems — Part 6: DiagnosticsISO 16844-7Road vehicles — Tachograph systems — Part 7: ParametersISO 534Paper and board — Determination of thickness, density and specific volumeUN ECE R10Uniform provisions concerning the approval of vehicles with regard to electromagnetic compatibility (United Nation Economic Commission for Europe)
 2. 

No
                                        
                                          Test
                                        
                                          Description
                                        
                                          Related requirements
                                       

                                             1.
                                           
                                             Administrative examination
                                          

                                          1.1
                                        
                                          Documentation
                                        
                                          Correctness of documentation
                                        

                                          1.2
                                        
                                          Manufacturer test results
                                        Results of manufacturer test performed during integration.Paper demonstrations. 
                                          88, 89,91
                                       

                                             2.
                                           
                                             Visual inspection
                                          

                                          2,1
                                        
                                          Compliance with documentation
                                        

                                          2.2
                                        
                                          Identification / markings
                                        
                                          224 to 226
                                       

                                          2.3
                                        
                                          Materials
                                        
                                          219 to 223
                                       

                                          2.4
                                        
                                          Sealing
                                        
                                          398, 401 to 405
                                       

                                          2.5
                                        
                                          External interfaces
                                        

                                             3.
                                           
                                             Functional tests
                                          

                                          3.1
                                        
                                          Functions provided
                                        
                                          02, 03, 04, 05, 07, 382
                                       

                                          3.2
                                        
                                          Modes of operation
                                        
                                          09 to 11*, 134, 135
                                       

                                          3.3
                                        
                                          Functions and data access rights
                                        
                                          12* 13*, 382, 383, 386 to 389
                                       

                                          3.4
                                        
                                          Monitoring cards insertion and withdrawal
                                        
                                          15, 16, 17, 18, 19*, 20*, 134
                                       

                                          3.5
                                        
                                          Speed and distance measurement
                                        
                                          21 to 31
                                       

                                          3.6
                                        
                                          Time measurement (test performed at 20 °C)
                                        
                                          38 to 43
                                       

                                          3.7
                                        
                                          Monitoring driver activities
                                        
                                          44 to 53, 134
                                       

                                          3.8
                                        
                                          Monitoring driving status
                                        
                                          54, 55, 134
                                       

                                          3.9
                                        
                                          Manual entries
                                        
                                          56 to 62
                                       

                                          3.10
                                        
                                          Company locks management
                                        
                                          63 to 68
                                       

                                          3.11
                                        
                                          Monitoring control activities
                                        
                                          69, 70
                                       

                                          3.12
                                        
                                          Detection of events and/or faults
                                        
                                          71 to 88, 134
                                       

                                          3.13
                                        
                                          Equipment identification data
                                        
                                          93*, 94*, 97, 100
                                       

                                          3.14
                                        
                                          Driver card insertion and withdrawal data
                                        
                                          102* to 104*
                                       

                                          3.15
                                        
                                          Driver activity data
                                        
                                          105* to 107*
                                       

                                          3.16
                                        
                                          Places and positions data
                                        
                                          108* to 112*
                                       

                                          3.17
                                        
                                          Odometer data
                                        
                                          113* to 115*
                                       

                                          3.18
                                        
                                          Detailed speed data
                                        
                                          116*
                                       

                                          3.19
                                        
                                          Events data
                                        
                                          117*
                                       

                                          3.20
                                        
                                          Faults data
                                        
                                          118*
                                       

                                          3.21
                                        
                                          Calibration data
                                        
                                          119* to 121*
                                       

                                          3.22
                                        
                                          Time adjustment data
                                        
                                          124*, 125*
                                       

                                          3.23
                                        
                                          Control activity data
                                        
                                          126*, 127*
                                       

                                          3.24
                                        
                                          Company locks data
                                        
                                          128*
                                       

                                          3.25
                                        
                                          Download activity data
                                        
                                          129*
                                       

                                          3.26
                                        
                                          Specific conditions data
                                        
                                          130*, 131*
                                       

                                          3.27
                                        
                                          Recording and storing on tachographs cards
                                        136, 137, 138*, 139*, 141*, 142, 143144, 145, 146*, 147*, 148*, 149, 150

                                          3.28
                                        
                                          Displaying
                                        90, 134,151 to 168,PIC_001, DIS_001

                                          3.29
                                        
                                          Printing
                                        90, 134,169 to 181, PIC_001, PRT_001 to PRT_014

                                          3.30
                                        
                                          Warning
                                        134, 182 to 191,PIC_001

                                          3.31
                                        
                                          Data downloading to external media
                                        
                                          90, 134, 192 to 196
                                       

                                          3.32
                                        
                                          Remote communication for targeted roadside checks
                                        
                                          197 to 199
                                       

                                          3.33
                                        
                                          Output data to additional external devices
                                        
                                          200, 201
                                       

                                          3.34
                                        
                                          Calibration
                                        
                                          202 to 206*, 383, 384, 386 to 391
                                       

                                          3.35
                                        
                                          Roadside calibration checking
                                        
                                          207 to 209
                                       

                                          3.36
                                        
                                          Time adjustment
                                        
                                          210 to 212*
                                       

                                          3.37
                                        
                                          Non-interference of additional functions
                                        
                                          06, 425
                                       

                                          3.38
                                        
                                          Motion sensor interface
                                        
                                          02, 122
                                       

                                          3.39
                                        
                                          External GNSS facility
                                        
                                          03, 123
                                       

                                          3.40
                                        
                                          Verify that the VU detects, records and stores the event(s) and/or fault(s) defined by the VU manufacturer when a paired motion sensor reacts to magnetic fields disturbing vehicle motion detection.
                                        
                                          217
                                       

                                          3.41
                                        
                                          Cypher suite and standardized domain parameters
                                        
                                          CSM_48, CSM_50
                                       

                                             4.
                                           
                                             Environmental tests
                                          

                                          4.1
                                        
                                          Temperature
                                        Verify functionality through:
 Test according to ISO 16750-4, Chapter 5.1.1.2: Low temperature operation test (72 h @ – 20 °C)
 This test refers to IEC 60068-2-1: Environmental testing - Part 2-1: Tests - Test A: Cold
 Test according to ISO 16750-4: Chapter 5.1.2.2: High temperature operation test (72 h at 70 °C)
 This test refers to IEC 60068-2-2: Basic environmental testing procedures; part 2: tests; tests B: dry heat
 Test according to ISO 16750-4: Chapter 5.3.2: Rapid change of temperature with specified transition duration (– 20 °C/70 °C, 20 cycles, dwell time 2h at each temperature)
A reduced set of tests (among those defined in section 3 of this table) can be carried out at the lower temperature, the higher temperature and during the temperature cycles 
                                          213
                                       

                                          4.2
                                        
                                          Humidity
                                        
                                          Verify that the vehicle unit can withstand a cyclic damp (heat test) through IEC 60068-2-30, test Db, six 24 hours cycles, each temperature varying from +25 °C to + 55 °C and a relative humidity of 97 % at + 25 °C and equal to 93 % at +55 °C
                                        
                                          214
                                       

                                          4.3
                                        
                                          Mechanical
                                        
1.. Sinusoidal vibrations.
verify that the vehicle unit can withstand sinusoidal vibrations with the following characteristics:

 constant displacement between 5 and 11 Hz: 10mm peak
 constant acceleration between 11 and 300 Hz: 5g
 This requirement is verified through IEC 60068-2-6, test Fc, with a minimum test duration of 3 × 12 hours (12 hours per axis)
 ISO 16750-3 does not require a sinusoidal vibration test for devices located in the decoupled vehicle cab.
2.. Random vibrations:
Test according to ISO 16750-3: Chapter 4.1.2.8: Test VIII: Commercial vehicle, decoupled vehicle cab
Random vibration test, 10…2000 Hz, RMS vertical 21,3 m/s
                                                         2
                                                      , RMS longitudinal 11,8 m/s
                                                         2
                                                      , RMS lateral 13,1 m/s
                                                         2
                                                      , 3 axes, 32 h per axis, including temperature cycle – 20…70 °C.
This test refers to IEC 60068-2-64: Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband random and guidance
3.. Shocks:
mechanical shock with 3 g half sinus according ISO 16750.The tests described above are performed on different samples of the equipment type being tested. 
                                          219
                                       

                                          4.4
                                        
                                          Protection against water and foreign bodies
                                        
                                          Test according to ISO 20653: Road vehicles – Degree of protection (IP code) – Protection of electrical equipment against foreign objects, water and access (No change in parameters); Minimum value IP 40
                                        
                                          220, 221
                                       

                                          4.5
                                        
                                          Over-voltage protection
                                        Verify that the vehicle unit can withstand a power supply of:
                                                   24 V versions
                                                34V at + 40 °C 1 hour
                                                   12V versions
                                                17V at + 40 °C 1 hour(ISO 16750-2) 
                                          216
                                       

                                          4.6
                                        
                                          Reverse polarity protection
                                        Verify that the vehicle unit can withstand an inversion of its power supply(ISO 16750-2) 
                                          216
                                       

                                          4.7
                                        
                                          Short-circuit protection
                                        Verify that input output signals are protected against short circuits to power supply and ground(ISO 16750-2) 
                                          216
                                       

                                             5.
                                           
                                             EMC tests
                                          

                                          5.1
                                        
                                          Radiated emissions and susceptibility
                                        
                                          Compliance with Regulation ECE R10
                                        
                                          218
                                       

                                          5.2
                                        
                                          Electrostatic discharge
                                        Compliance with ISO 10605:2008 +Technical Corrigendum:2010 +AMD1:2014: +/– 4 kV for contact and +/– 8 kV for air discharge 
                                          218
                                       

                                          5.3
                                        
                                          Conducted transient susceptibility on power supply
                                        For 24V versions: compliance with ISO 7637-2 + ECE Regulation No. 10 Rev. 3:
 pulse 1a: Vs=450V Ri=50 ohms
 pulse 2a: Vs=+37V Ri=2 ohms
 pulse 2b: Vs=+20V Ri=0,05 ohms
 pulse 3a: Vs=– 150V Ri=50 ohms
 pulse 3b: Vs=+150V Ri=50 ohms
 pulse 4: Vs=– 16V Va=– 12V t6=100ms
 pulse 5: Vs=+120V Ri=2,2 ohms td=250msFor 12V versions: compliance with ISO 7637– 1 + ECE Regulation No. 10 Rev. 3:
 pulse 1: Vs=– 75V Ri=10 ohms
 pulse 2a: Vs=+37V Ri=2 ohms
 pulse 2b: Vs=+10V Ri=0,05 ohms
 pulse 3a: Vs=– 112V Ri=50 ohms
 pulse 3b: Vs=+75V Ri=50 ohms
 pulse 4: Vs=– 6V Va=– 5V t6=15ms
 pulse 5: Vs=+65V Ri=3ohms td=100ms
 Pulse 5 shall be tested only for vehicle units designed to be installed in vehicles for which no external common protection against load dump is implementedFor load dump proposal, refer to ISO 16750-2, 4th edition, chapter 4.6.4. 
                                          218
 3. 

No Test Description Related requirements
1. Administrative examination
1.1 Documentation Correctness of documentation 
2. Visual inspection
2.1. Compliance with documentation 
2.2. Identification/markings 225, 226,
2.3 Materials 219 to 223
2.4. Sealing 398, 401 to 405
3. Functional tests
3.1 Sensor identification data 95 to 97*
3.2 Motion sensor — vehicle unit pairing 122*, 204
3.3 Motion detectionMotion measurement accuracy 30 to 35
3.4 Vehicle unit interface 02
3.5 Check that the motion sensor is immune to constant magnetic field. Alternatively, verify that the motion sensor reacts to constant magnetic fields disturbing vehicle motion detection so that a connected VU can detect, record and store sensor faults 217
4. Environmental tests
4.1 Operating temperature Verify functionality (as defined in test No 3.3) in temperature range [– 40°C; + 135°C] through:
 IEC 60068-2-1 test Ad, with a test duration of 96 hours at the lowest temperature Tomin,
 IEC 60068-2-2 test Bd, with a test duration of 96 hours at the highest temperature Tomax
 Test according to ISO 16750-4: Chapter 5.1.1.2: Low temperature operation test (24 h @ – 40 °C)
This test refers to IEC 60068-2-1: Environmental testing — Part 2-1: Tests — Test A: Cold IEC 68-2-2 test Bd, with a test duration of 96 hours at the lowest temperature of – 40°C.
 Test according to ISO 16750-4: Chapter 5.1.2.2: High temperature operation test (96 h @ 135 °C)
This test refers to IEC 60068-2-2: Basic environmental testing procedures; part 2: tests; tests B: dry heat 213
4.2 Temperature cycles Test according to ISO 16750-4: Chapter 5.3.2: Rapid change of temperature with specified transition duration (– 40°C/135 °C, 20 cycles, dwell time 30 min at each temperature)IEC 60068-2-14: Environmental testing; Part 2-14: Tests; Test N: Change of temperature 213
4.3 Humidity cycles Verify functionality (as defined in test No. 3.3) through IEC 60068-2-30, test Db, six 24 hours cycles, each temperature varying from + 25°C to + 55°C and a relative humidity of 97 % at + 25°C and equal to 93 % at + 55°C 214
4.4 Vibration ISO 16750-3: Chapter 4.1.2.6: Test VI: Commercial vehicle, engine, gearboxMixed mode vibration test including
a)) Sinusoidal vibration test, 20…520 Hz, 11,4 … 120 m/s2, <= 0,5 oct/min
b)) Random vibration test, 10…2 000 Hz, RMS 177 m/s294 h per axis, including temperature cycle – 20…70°C)This test refers to IEC 60068-2-80: Environmental testing — Part 2-80: Tests — Test Fi: Vibration — Mixed mode 219
4.5 Mechanical shock ISO 16750-3: Chapter 4.2.3: Test VI: Test for devices in or on the gearboxhalf-sinusoidal shock, acceleration to be agreed in the range 3 000…15 000 m/s2, pulse duration to be agreed, however < 1 ms, number of shocks: to be agreedThis test refers to IEC 60068-2-27: Environmental testing. Part 2: Tests. Test Ea and guidance: Shock 219
4.6 Protection against water and foreign bodies Test according to ISO 20653: Road vehicles — Degree of protection (IP code) — Protection of electrical equipment against foreign objects, water and access(Target value IP 64) 220, 221
4.7 Reverse polarity protection Verify that the motion sensor can withstand an inversion of its power supply 216
4.8 Short circuit protection Verify that input output signals are protected against short circuits to power supply and ground 216
5. EMC
5.1 radiated emissions and susceptibility Verify compliance with Regulation ECE R10 218
5.2 Electrostatic discharge Compliance with ISO 10605:2008 + Technical Corrigendum:2010 + AMD1:2014: +/– 4kV for contact and +/– 8kV for air discharge 218
5.3 Conducted transient susceptibility on data lines) For 24V versions: compliance with ISO 7637-2 + ECE Regulation No. 10 Rev. 3:
 pulse 1a: Vs = – 450 V Ri = 50 ohms
 pulse 2a: Vs = + 37 V Ri = 2 ohms
 pulse 2b: Vs = + 20 V Ri = 0,05 ohms
 pulse 3a: Vs = – 150 V Ri = 50 ohms
 pulse 3b: Vs = + 150 V Ri = 50 ohms
 pulse 4: Vs= – 16 V Va = – 12 V t6 = 100ms
 pulse 5: Vs = + 120 V Ri = 2,2 ohms td = 250msFor 12V versions: compliance with ISO 7637-1 + ECE Regulation No. 10 Rev. 3:
 pulse 1: Vs = – 75 V Ri = 10 ohms
 pulse 2a: Vs = + 37 V Ri = 2 ohms
 pulse 2b: Vs = + 10 V Ri = 0,05 ohms
 pulse 3a: Vs = – 112 V Ri = 50 ohms
 pulse 3b: Vs = + 75 V Ri = 50 ohms
 pulse 4: Vs= – 6 V Va=-5 V t6 = 15 ms
 pulse 5: Vs = + 65 V Ri = 3 ohms td = 100 msPulse 5 shall be tested only for vehicle units designed to be installed in vehicles for which no external common protection against load dump is implementedFor load dump proposal, refer to ISO 16750-2, 4th edition, chapter 4.6.4 218
 4. 
Tests according to this Section 4,


 no. 5 ‘Protocol tests’,
 no. 6 ‘Card structure’ and
 no. 7 ‘Functional tests’

can be performed by the evaluator or certifier during the Common Criteria (CC) security certification process for the chip module.

Tests number 2.3 and 4.2 are the same. These are the mechanical tests of the combination card body and chip module. If one of these components (card body, chip module) is changed, then these tests are necessary.


No Test Description Related requirements
1. Administrative examination
1.1 Documentation Correctness of documentation 
2 Card Body
2.1 Printed Design Make sure that all features for protection and visible data are correctly printed on the card and compliant.
[Designator]
Annex 1C, chapter 4.1 ‘Visible data’, 227)
The front page shall contain:
the words ‘Driver card’ or ‘Control card’ or ‘Workshop card’ or ‘Company card’ printed in capital letters in the official language or languages of the Member State issuing the card, according to the type of the card.

[Member State name]
Annex 1C, chapter 4.1 ‘Visible data’, 228)
The front page shall contain:
the name of the Member State issuing the card (optional).

[Sign]
Annex 1C, chapter 4.1 ‘Visible data’, 229)
The front page shall contain:
the distinguishing sign of the Member State issuing the card, printed in negative in a blue rectangle and encircled by 12 yellow stars.

[Enumeration]
Annex 1C, chapter 4.1 ‘Visible data’, 232)
The reverse page shall contain:
an explanation of the numbered items which appear on the front page of the card.

[Colour]
Annex 1C, chapter 4.1 ‘Visible data’, 234)
Tachograph cards shall be printed with the following background predominant colours:

— driver card: white,
— workshop card: red,
— control card: blue,
— company card: yellow.

[Security]
Annex 1C, chapter 4.1 ‘Visible data’, 235)
Tachograph cards shall bear at least the following features for protection of the card body against counterfeiting and tampering:

— a security design background with fine guilloche patterns and rainbow printing,
— at least one two-coloured microprint line.

[Markings]
Annex 1C, chapter 4.1 ‘Visible data’, 236)
Member States may add colours or markings, such as national symbols and security features.

[Approval mark]
Tachograph cards shall contain an approval mark.
The approval mark shall be made up of:

— a rectangle, within which shall be placed the letter ‘e’ followed by a distinguishing number or letter for the country which has issued the approval,
— an approval number corresponding to the number of the approval certificate for a tachograph card, placed at any point within the immediate proximity of this rectangle.
 227 to 229, 232, 234 to 236
2.2 Mechanical Tests 
[Card size]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[5] Dimension of card,
[5.1] Card size,
[5.1.1] Card dimensions and tolererances,
card type ID-1 Unused card

[Card edges]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[5] Dimension of card,
[5.1] Card size,
[5.1.2] Card edges

[Card construction]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[6] Card construction

[Card materials]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[7] Card materials

[Bending stiffness]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.1] Bending stiffness

[Toxicity]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.3] Toxicity

[Resistance to chemicals]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.4] Resistance to chemicals

[Card stability]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.5] Card dimensional stability and warpage with temperature and humidity

[Light]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.6] Light

[Durability]
Annex 1C, chapter 4.4 ‘Environmental and electrical specifications’, 241)
Tachograph cards shall be capable of operating correctly for a five-year period if used within the environmental and electrical specifications.

[Peel strength]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.8] Peel strength

[Adhesion or blocking]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.9] Adhesion or blocking

[Warpage]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.11] Overall card warpage

[Resistance to heat]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.12] Resistance to heat

[Surface distortions]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.13] Surface distortions

[Contamination]
Tachograph cards must conform to standard
ISO/IEC 7810, Identification cards — Physical characteristics,
[8] Card characteristics,
[8.14] Contamination and interaction of card components
 240, 243ISO/IEC 7810
2.3 Mechanical tests with chip module embedded 
[Bending]
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.2] Dynamic bending stress
Total number of bending cycles: 4 000.

[Torsion]
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.3] Dynamic torsional stress
Total number of torsion cycles: 4 000.
 ISO/IEC 7810
3 Module
3.1 Module Module is the chip encapsulation and the contact plate.
[Surface profile]
Tachograph cards must conform to standard
ISO/IEC 7816-1:2011, Identification cards — Integrated circuit cards — Part 1: Cards with contacts — Physical characteristics
[4.2] Surface profile of contacts

[Mechanical strength]
Tachograph cards must conform to standard
ISO/IEC 7816-1:2011, Identification cards — Integrated circuit cards — Part 1: Cards with contacts — Physical characteristics
[4.3] Mechanical strength (of a card and contacts)

[Electrical resistance]
Tachograph cards must conform to standard
ISO/IEC 7816-1:2011, Identification cards — Integrated circuit cards — Part 1: Cards with contacts — Physical characteristics
[4.4] Electrical resistance (of contacts)

[Dimension]
Tachograph cards must conform to standard
ISO/IEC 7816-2:2007, Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimension and location of the contacts
[3] Dimension of the contacts

[Location]
Tachograph cards must conform to standard
ISO/IEC 7816-2:2007, Identification cards — Integrated circuit cards — Part 2: Cards with contacts — Dimension and location of the contacts
[4] Number and location of the contacts
In case of modules with six contacts, contact ‘C4’ and ‘C8’ are not part of this test requirement.
 ISO/IEC 7816
4 Chip
4.1 Chip 
[Operating temperature]
The Tachograph card chip shall operate in an ambient temperature range between – 25 °C and + 85 °C.

[Temperature and humidity]
Annex 1C, chapter 4.4 ‘Environmental and electrical specifications’, 241)
Tachograph cards shall be capable of operating correctly in all the climatic conditions normally encountered in Community territory and at least in the temperature range – 25°C to + 70°C with occasional peaks of up to + 85°C, ‘occasional’ meaning not more than 4 hours each time and not over 100 times during the life time of the card.
The Tachograph cards are exposed in consecutive steps to the following temperatures and humidities for the given time. After each step the Tachograph cards are tested for electrical functionality.

1.. Temperature of – 20 °C for 2 h.
2.. Temperature of +/– 0 °C for 2 h.
3.. Temperature of + 20 °C, 50 % RH, for 2 h.
4.. Temperature of + 50 °C, 50 % RH, for 2 h.
5.. Temperature of + 70 °C, 50 % RH, for 2 h.
The temperature is increased intermittently to + 85 °C, 50 % RH, for 60 min.
6.. Temperature of + 70 °C, 85 % RH, for 2 h.
The temperature is increased intermittently to + 85 °C, 85 % RH, for 30 min.

[Humidity]
Annex 1C, chapter 4.4 ‘Environmental and electrical specifications’, 242)
Tachograph cards shall be capable of operating correctly in the humidity range 10 % to 90 %.

[Electromagnetic compatibility — EMC]
Annex 1C, chapter 4.4 ‘Environmental and electrical specifications’ 244)
During operation, Tachograph cards shall conform to ECE R10 related to electromagnetic compatibility.

[Static electricity]
Annex 1C, chapter 4.4 ‘Environmental and electrical specifications’, 244)
During operation, Tachograph cards shall be protected against electrostatic discharges.
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.4] Static electricity
[9.4.1] Contact IC cards
Test voltage: 4 000 V.

[X-rays]
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.1] X-rays

[Ultraviolet light]
ISO/IEC 10373-1:2006, Identification cards — Test methods — Part 1: General characteristics
[5.11] Ultraviolet light

[3-wheel]
Tachograph cards must conform to standard
ISO/IEC 10373-1:2006/Amd. 1:2012, Identification cards — Test methods — Part 1: General characteristics, Amendment 1
[5.22] ICC — Mechanical strength: 3 wheel test for ICCs with contacts

[Wrapping]
Tachograph cards must conform to standard
MasterCard CQM V2.03:2013
[11.1.3] R-L3-14-8: Wrapping Test Robustness
[13.2.1.32] TM-422: Mechanical Reliability: Wrapping Test
 241 to 244ECE R10ISO/IEC 7810ISO/IEC 10373
4.2 Mechanical tests chip module embedded in the card body-> same as 2.3 
[Bending]
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.2] Dynamic bending stress
Total number of bending cycles: 4 000.

[Torsion]
Tachograph cards must conform to standard
ISO/IEC 7810:2003/Amd. 1:2009, Identification cards — Physical characteristics, Amendment 1: Criteria for cards containing integrated circuits
[9.3] Dynamic torsional stress
Total number of torsion cycles: 4 000.
 ISO/IEC 7810
5 Protocol tests
5.1 ATR Check that the ATR is compliant ISO/IEC 7816-3TCS_14, TCS_17, TCS_18
5.2 T=0 Check that T=0 protocol is compliant ISO/IEC 7816-3TCS_11, TCS_12, TCS_13, TCS_15
5.3 PTS Check that the PTS command is compliant by setting T=1 from T=0. ISO/IEC 7816-3TCS_12, TCS_19, TCS_20, TCS_21
5.4 T=1 Check that T=1 protocol is compliant ISO/IEC 7816-3TCS_11, TCS_13, TCS_16
6 Card structure
6.1  Test that the file structure of the card is compliant by checking the presence of the mandatory files in the card and their access conditions TCS_22 to TCS_28TCS_140 to TCS_179
7 Functional tests
7.1 Normal processing Test at least once each allowed usage of each command (ex: test the UPDATE BINARY command with CLA = ‘00’, CLA = ‘0C’ and with different P1,P2 and Lc parameters)Check that the operations have actually been performed in the card (ex: by reading the file the command has been performed on) TCS_29 to TCS_139
7.2 Error messages Test at least once each error message (as specified in Appendix 2) for each commandTest at least once every generic error (except ‘6400’ integrity errors checked during security certification)
7.3 Cypher suite and standardized domain parameters CSM_48, CSM_50
8 Personalisation
8.1 Optical personalisation 
Annex 1C, chapter 4.1 ‘Visible data’, 230)
The front page shall contain:
information specific to the card issued.

Annex 1C, chapter 4.1 ‘Visible data’, 231)
The front page shall contain:
dates using a ‘dd/mm/yyyy’ or ‘dd.mm.yyyy’ format (day, month, year).

Annex 1C, chapter 4.1 ‘Visible data’, 235)
Tachograph cards shall bear at least the following features for protection of the card body against counterfeiting and tampering:

— in the area of the photograph, the security design background and the photograph shall overlap.
 230, 231, 235
 5. 

No Test Description Related requirements
1. Administrative examination
1.1 Documentation Correctness of documentation 
2. Visual inspection for external GNSS facility
2.1. Compliance with documentation 
2.2. Identification/markings 224 to 226
2.3 Materials 219 to 223
3. Functional tests
3.1 Sensor identification data 98,99
3.2 External GNSS module — vehicle unit coupling 123, 205
3.3 GNSS position 36, 37
3.4 Vehicle unit interface when the GNSS receiver is external to the Vehicle Unit 03
3.5 Cypher suite and standardized domain parameters CSM_48, CSM_50
4. Environmental tests
4.1 Temperature Verify functionality through:
 Test according to ISO 16750-4, Chapter 5.1.1.2: Low temperature operation test (72 h @ – 20 °C)
This test refers to IEC 60068-2-1: Environmental testing — Part 2-1: Tests — Test A: Cold
 Test according to ISO 16750-4: Chapter 5.1.2.2: High temperature operation test (72 h @ 70 °C)
This test refers to IEC 60068-2-2: Basic environmental testing procedures; part 2: tests; tests B: dry heat
 Test according to ISO 16750-4: Chapter 5.3.2: Rapid change of temperature with specified transition duration (– 20 °C/70 °C, 20 cycles, dwell time 1 h at each temperature)
A reduced set of tests (among those defined in section 3 of this table) can be carried out at the lower temperature, the higher temperature and during the temperature cycles 213
4.2 Humidity Verify that the vehicle unit can withstand a cyclic damp (heat test) through IEC 60068-2-30, test Db, six 24 hours cycles, each temperature varying from + 25 °C to + 55 °C and a relative humidity of 97 % at + 25 °C and equal to 93 % at + 55 °C 214
4.3 Mechanical 
1.. Sinusoidal vibrations.
verify that the vehicle unit can withstand sinusoidal vibrations with the following characteristics:

 constant displacement between 5 and 11 Hz: 10 mm peak
 constant acceleration between 11 and 300 Hz: 5g
This requirement is verified through IEC 60068-2-6, test Fc, with a minimum test duration of 3 × 12 hours (12 hours per axis)
ISO 16750-3 does not require a sinusoidal vibration test for devices located in the decoupled vehicle cab.
2.. Random vibrations:
Test according to ISO 16750-3: Chapter 4.1.2.8: Test VIII: Commercial vehicle, decoupled vehicle cab
Random vibration test, 10…2 000 Hz, RMS vertical 21,3 m/s2, RMS longitudinal 11,8 m/s2, RMS lateral 13,1 m/s2, 3 axes, 32 h per axis, including temperature cycle – 20…70°C.
This test refers to IEC 60068-2-64: Environmental testing — Part 2-64: Tests — Test Fh: Vibration, broadband random and guidance
3.. Shocks:
mechanical shock with 3g half sinus according ISO 16750.The tests described above are performed on different samples of the equipment type being tested. 219
4.4 Protection against water and foreign bodies Test according to ISO 20653: Road vehicles — Degree of protection (IP code) — Protection of electrical equipment against foreign objects, water and access (No change in parameters) 220, 221
4.5 Over-voltage protection Verify that the vehicle unit can withstand a power supply of: 216
24 V versions: 34 V at + 40 °C 1 hour
12V versions: 17 V at + 40 °C 1 hour
( ISO 16750-2, chapter 4.3)
4.6 Reverse polarity protection Verify that the vehicle unit can withstand an inversion of its power supply(ISO 16750-2, chapter 4.7) 216
4.7 Short-circuit protection Verify that input output signals are protected against short circuits to power supply and ground(ISO 16750-2, chapter 4.10]) 216
5 EMC tests
5.1 Radiated emissions and susceptibility Compliance with Regulation ECE R10 218
5.2 Electrostatic discharge Compliance with ISO 10605:2008 + Technical Corrigendum: 2010 + AMD1:2014: +/– 4kV for contact and +/– 8kV for air discharge 218
5.3 Conducted transient susceptibility on power supply For 24V versions: compliance with ISO 7637-2 + ECE Regulation No. 10 Rev. 3:
 pulse 1a: Vs = – 450V Ri = 50 ohms
 pulse 2a: Vs= + 37V Ri = 2 ohms
 pulse 2b: Vs= + 20V Ri = 0,05 ohms
 pulse 3a: Vs= – 150V Ri = 50 ohms
 pulse 3b: Vs=+ 150V Ri = 50 ohms
 pulse 4: Vs = – 16 V Va = – 12V t6 = 100 ms
 pulse 5: Vs= + 120 V Ri = 2,2 ohms td = 250 msFor 12V versions: compliance with ISO 7637-1 + ECE Regulation No. 10 Rev. 3:
 pulse 1: Vs= – 75V Ri=10 ohms
 pulse 2a: Vs= + 37V Ri=2 ohms
 pulse 2b: Vs= + 10V Ri=0,05 ohms
 pulse 3a: Vs= – 112V Ri=50 ohms
 pulse 3b: Vs= + 75V Ri=50 ohms
 pulse 4: Vs= – 6V Va=-5V t6=15ms
 pulse 5: Vs= + 65V Ri=3ohms td=100msPulse 5 shall be tested only for vehicle units designed to be installed in vehicles for which no external common protection against load dump is implementedFor load dump proposal, refer to ISO 16750-2, 4th edition, chapter 4.6.4. 218
 6. 


                                          No
                                        
                                          Test
                                        
                                          Description
                                        
                                          Related requirements
                                       

                                          1.
                                        
                                             Administrative examination
                                          

                                          1.1
                                        
                                          Documentation
                                        
                                          Correctness of documentation
                                        

                                          2.
                                        
                                             Visual inspection
                                          

                                          2.1.
                                        
                                          Compliance with documentation
                                        

                                          2.2.
                                        
                                          Identification / markings
                                        
                                          225, 226
                                       

                                          2.3
                                        
                                          Materials
                                        
                                          219 to 223
                                       

                                             3.
                                           
                                             Functional tests
                                          

                                          3.1
                                        
                                          Remote communication for targeted roadside checks
                                        
                                          4, 197 to 199
                                       

                                          3.2
                                        
                                          Recording and storing in data memory
                                        
                                          91
                                       

                                          3.3
                                        
                                          Communication with Vehicle Unit
                                        
                                          Appendix 14 DSC_66 to DSC_70, DSC_71 to DSC_76
                                       

                                          4.
                                        
                                             Environmental tests
                                          

                                          4.1
                                        
                                          Temperature
                                        Verify functionality through:
 Test according to ISO 16750-4, Chapter 5.1.1.2: Low temperature operation test (72 h @ – 20 °C)
This test refers to IEC 60068-2-1: Environmental testing - Part 2-1: Tests - Test A: Cold
 Test according to ISO 16750-4: Chapter 5.1.2.2: High temperature operation test (72 h @ 70 °C)
This test refers to IEC 60068-2-2: Basic environmental testing procedures; part 2: tests; tests B: dry heat
 Test according to ISO 16750-4: Chapter 5.3.2: Rapid change of temperature with specified transition duration (– 20 °C/70 °C, 20 cycles, dwell time 1 h at each temperature)
A reduced set of tests (among those defined in section 3 of this table) can be carried out at the lower temperature, the higher temperature and during the temperature cycles 
                                          213
                                       

                                          4.2
                                        
                                          Protection against water and foreign bodies
                                        
                                          Test according to ISO 20653: Road vehicles – Degree of protection (IP code) – Protection of electrical equipment against foreign objects, water and access (targeted value IP40)
                                        
                                          220, 221
                                       

                                             5
                                           
                                             EMC tests
                                          

                                          5.1
                                        
                                          Radiated emissions and susceptibility
                                        
                                          Compliance with Regulation ECE R10
                                        
                                          218
                                       

                                          5.2
                                        
                                          Electrostatic discharge
                                        
                                          Compliance with ISO 10605:2008 + Technical Corrigendum:2010 + AMD1:2014: +/– 4 kV for contact and +/– 8 kV for air discharge
                                        
                                          218
                                       

                                          5.3
                                        
                                          Conducted transient susceptibility on power supply
                                        For 24V versions: compliance with ISO 7637-2 + ECE Regulation No. 10 Rev. 3:
 pulse 1a: Vs=– 450V Ri=50 ohms
 pulse 2a: Vs=+37V Ri=2 ohms
 pulse 2b: Vs=+20V Ri=0,05 ohms
 pulse 3a: Vs=– 150V Ri=50 ohms
 pulse 3b: Vs=+150V Ri=50 ohms
 pulse 4: Vs=– 16V Va=-12V t6=100ms
 pulse 5: Vs=+120V Ri=2,2 ohms td=250msFor 12V versions: compliance with ISO 7637-1 + ECE Regulation No. 10 Rev. 3:
 pulse 1: Vs=-75V Ri=10 ohms
 pulse 2a: Vs=+37V Ri=2 ohms
 pulse 2b: Vs=+10V Ri=0,05 ohms
 pulse 3a: Vs=– 112V Ri=50 ohms
 pulse 3b: Vs=+75V Ri=50 ohms
 pulse 4: Vs=– 6V Va=– 5V t6=15ms
 pulse 5: Vs=+65V Ri=3ohms td=100ms
 Pulse 5 shall be tested only for vehicle units designed to be installed in vehicles for which no external common protection against load dump is implementedFor load dump proposal, refer to ISO 16750-2, 4th edition, chapter 4.6.4. 
                                          218
 7. 

No Test Description Related requirements
1. Administrative examination
1.1 Documentation Correctness of documentation 
2 General Tests
2.1 Number of characters per line Visual inspection of printouts. 172
2.2 Minimum character size Visual inspection of printout and character inspection. 173
2.3 Supported character sets The printer shall support characters specified in Appendix 1 Chapter 4 ‘Character sets’. 174
2.4 Printouts definition Check of tachograph type approval and visual inspection of printouts 174
2.5 Legibility and identification of printouts Inspection of printoutsDemonstrated by test reports and test protocols by manufacturer.All homologation number(s) of tachographs with which the printer paper may be used are imprinted on the paper. 175, 177, 178
2.6 Addition of handwritten notes Visual inspection: Field for signature of the driver is available.Fields for additional other handwritten entries are available. 180
2.7 Additional details on paper faces. Paper's face and reverse side may feature additional details and information.These additional details and information may not interfere with the legibility of the printouts.Visual inspection. 177, 178
3 Storage Tests
3.1 Dry Heat Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidityTest environment: 72 hours at + 70 °C ± 2 °CRecovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178IEC 60068-2-2-Bb
2.2 Damp Heat Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ±3 % relative humidityTest environment: 144 hours at + 55 °C ± 2 °C and 93 % ± 3 % r.h.Recovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178IEC 60068-2-78-Cab
4 Paper In-Service Tests
4.1 Humidity resistance background (unprinted paper) Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ±3 % relative humidityTest environment: 144 hours at + 55 °C ± 2 °C and 93 % ± 3 % r.h.Recovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178IEC 60068-2-78-Cab
4.2 Printability Preconditioning: 24 hours at + 40 °C ± 2 °C/93 % ± 3 % relative humidityTest environment: printout produced at + 23 °C ± 2 °CRecovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178
4.3 Heat resistance Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidityTest environment: 2 hours at + 70 °C ± 2 °C, dry heatRecovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178IEC 60068-2-2-Bb
4.4 Low temperature resistance Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidityTest environment: 24 hours – 20 °C ± 3 °C, dry coldRecovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178ISO 60068-2-1-Ab
4.5 Light resistance Preconditioning: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidityTest environment: 100 hours under 5 000 Lux illumination at + 23 °C ± 2 °C/55 % ± 3 % relative humidityRecovery: 16 hours at + 23 °C ± 2 °C/55 % ± 3 % relative humidity 176, 178

Legibility criteria for tests 3.x and 4.x:

Printout legibility is assured if optical densities comply with the following limits:


 Printed characters: min. 1,0
 Background (unprinted paper): max. 0,2

Optical densities of the resulting printouts shall be measured according to DIN EN ISO 534.

Printouts shall show no dimensional changes and remain clearly legible.
 8. 

No
                                        
                                          Test
                                        
                                          Description
                                       

                                          8.1 
                                          Interoperability tests between vehicle units and tachograph cards
                                       

                                          1
                                        
                                          Mutual authentication
                                        
                                          Check that the mutual authentication between the vehicle unit and the tachograph card runs normally
                                       

                                          2
                                        
                                          Write/read tests
                                        Execute a typical activity scenario on the vehicle unit. The scenario shall be adapted to the type of card being tested and involve writings in as many EFs as possible in the cardVerify through a vehicle unit downloading that all corresponding recordings have been properly madeVerify through a card downloading that all corresponding recordings have been properly madeVerify through daily printouts that all corresponding recordings can be properly read

                                          8.2 
                                          Interoperability tests between vehicle units and motion sensors
                                       

                                          1
                                        
                                          Pairing
                                        
                                          Check that the pairing between the vehicle units and the motion sensors runs normally
                                       

                                          2
                                        
                                          Activity tests
                                        Execute a typical activity scenario on the motion sensor. The scenario shall involve a normal activity and creating as many events or faults as possible.Verify through a vehicle unit downloading that all corresponding recordings have been properly madeVerify through a card downloading that all corresponding recordings have been properly madeVerify through a daily printout that all corresponding recordings can be properly read

                                          8.3 
                                          Interoperability tests between vehicle units and external GNSS facilities (when applicable)
                                       

                                          1
                                        
                                          Mutual authentication
                                        
                                          Check that the mutual authentication (coupling) between the vehicle unit and the external GNSS module runs normally.
                                       

                                          2
                                        
                                          Activity tests
                                        Execute a typical activity scenario on the external GNSS facility. The scenario shall involve a normal activity and creating as many events or faults as possible.Verify through a vehicle unit downloading that all corresponding recordings have been properly madeVerify through a card downloading that all corresponding recordings have been properly madeVerify through a daily printout that all corresponding recordings can be properly read

Appendix 10
This appendix specifies the IT security requirements for the smart tachograph system components (second-generation tachograph).
 SEC_001 

— vehicle unit
— tachograph card,
— motion sensor,
— external GNSS facility.
 SEC_002 The minimum IT security requirements to be met by each component needing to be security certified shall be defined in a component Protection Profile, according to the Common Criteria scheme.
 SEC_003 

— Protection Profile for vehicle unit,
— Protection Profile for tachograph card,
— Protection Profile for motion sensor,
— Protection Profile for external GNSS facility.

The Protection Profile for vehicle unit shall address the cases when the VU is designed to be used or not with an external GNSS facility. In the former case, the security requirements of the external GNSS facility are provided in the dedicated Protection Profile.
 SEC_004 Component manufacturers shall refine and complete the appropriate component Protection Profile as necessary, without amending or deleting existing threats, objectives, procedural means and security enforcing functions specifications, in order to build a Security Target against which they shall seek the security certification of the component.
 SEC_005 Strict conformance of such specific Security Target with the corresponding Protection Profile must be stated during the evaluation process.
 SEC_006 The assurance level for each Protection Profile shall be EAL4 augmented by the assurance components ATE_DPT.2 and AVA_VAN.5.

Appendix 11
This Appendix specifies the security mechanisms ensuring


— mutual authentication between different components of the tachograph system.
— confidentiality, integrity, authenticity and/or non-repudiation of data transferred between different components of the tachograph system or downloaded to external storage media.

This Appendix consists of two parts. Part A defines the security mechanisms for the first-generation tachograph system (digital tachograph). Part B defines the security mechanisms for the second-generation tachograph system (smart tachograph).

The mechanisms specified in Part A of this Appendix shall apply if at least one of the components of the tachograph system involved in a mutual authentication and/or data transfer process is of the first generation.

The mechanisms specified in Part B of this Appendix shall apply if both components of the tachograph system involved in the mutual authentication and/or data transfer process are of the second generation.

Appendix 15 provides more information regarding the use of first generation components in combination with second-generation components.
 PART A  1.  1.1. 
The following references are used in this Appendix:

SHA-1National Institute of Standards and Technology (NIST). FIPS Publication 180-1: Secure Hash Standard. April 1995.PKCS1RSA Laboratories. PKCS # 1: RSA Encryption Standard. Version 2.0. October 1998.TDESNational Institute of Standards and Technology (NIST). FIPS Publication 46-3: Data Encryption Standard. Draft 1999.TDES-OPANSI X9.52, Triple Data Encryption Algorithm Modes of Operation. 1998.ISO/IEC 7816-4Information Technology — Identification cards — Integrated circuit(s) cards with contacts — Part 4: Interindustry commands for interexchange. First edition: 1995 + Amendment 1: 1997.ISO/IEC 7816-6Information Technology — Identification cards — Integrated circuit(s) cards with contacts — Part 6: Interindustry data elements. First edition: 1996 + Cor 1: 1998.ISO/IEC 7816-8Information Technology — Identification cards — Integrated circuit(s) cards with contacts — Part 8: Security related interindustry commands. First edition 1999.ISO/IEC 9796-2Information Technology — Security techniques — Digital signature schemes giving message recovery — Part 2: Mechanisms using a hash function. First edition: 1997.ISO/IEC 9798-3Information Technology — Security techniques — Entity authentication mechanisms — Part 3: Entity authentication using a public key algorithm. Second edition 1998.ISO 16844-3Road vehicles — Tachograph systems — Part 3: Motion sensor interface.
 1.2. 
The following notations and abbreviated terms are used in this Appendix:

(Ka, Kb, Kc)a key bundle for use by the Triple Data Encryption Algorithm,CACertification Authority,CARCertification Authority Reference,CCCryptographic Checksum,CGCryptogram,CHCommand Header,CHACertificate Holder Authorisation,CHRCertificate Holder Reference,D()Decryption with DES,DEData Element,DOData Object,dRSA private key, private exponent,eRSA public key, public exponent,E()Encryption with DES,EQTEquipment,Hash()hash value, an output of Hash,Hashhash function,KIDKey Identifier,KmTDES key. Master Key defined in ISO 16844-3.KmVUTDES key inserted in vehicle units.KmWCTDES key inserted in workshop cards.mmessage representative, an integer between 0 and n-1,nRSA keys, modulus,PBPadding Bytes,PIPadding Indicator byte (for use in Cryptogram for confidentiality DO),PVPlain Value,ssignature representative, an integer between 0 and n-1,SSCSend Sequence Counter,SMSecure Messaging,TCBCTDEA Cipher Block Chaining Mode of OperationTDEATriple Data Encryption Algorithm,TLVTag Length Value,VUVehicle Unit,X.Cthe certificate of user X issued by a certification authority,X.CAa certification authority of user X,X.CA.PK o X.Cthe operation of unwrapping a certificate to extract a public key. It is an infix operator, whose left operand is the public key of a certification authority, and whose right operand is the certificate issued by that certification authority. The outcome is the public key of the user X whose certificate is the right operand,X.PKRSA public key of a user X,X.PK[I]RSA encipherment of some information I, using the public key of user X,X.SKRSA private key of a user X,X.SK[I]RSA encipherment of some information I, using the private key of user X,‘xx’an Hexadecimal value,||concatenation operator.
 2.  2.1.  CSM_001 

— authentication between vehicle units and cards,
— transport of Triple-DES session keys between vehicle units and tachograph cards,
— digital signature of data downloaded from vehicle units or tachograph cards to external media.
 CSM_002 Vehicle units and tachograph cards shall use a Triple DES symmetric cryptographic system to provide a mechanism for data integrity during user data exchange between vehicle units and tachograph cards, and to provide, where applicable, confidentiality of data exchange between vehicle units and tachograph cards.
 2.2.  2.2.1  CSM_003 
X.SK[m] = s = md mod n
X.PK[s] = m = se mod n

A more comprehensive description of the RSA function can be found in reference [PKCS1]. Public exponent, e, for RSA calculations is an integer between 3 and n-1 satisfying gcd(e, lcm(p-1, q-1))=1.
 2.2.2  CSM_004 The digital signature mechanisms shall use the SHA-1 hash algorithm as defined in reference [SHA-1].
 2.2.3  CSM_005 DES based algorithms shall be used in Cipher Block Chaining mode of operation.
 3.  3.1.  3.1.1  CSM_006 

— European level,
— Member State level,
— Equipment level.
 CSM_007 At European level, a single European key pair (EUR.SK and EUR.PK) shall be generated. The European private key shall be used to certify the Member States public keys. Records of all certified keys shall be kept. These tasks shall be handled by a European Certification Authority, under the authority and responsibility of the European Commission.
 CSM_008 At Member State level, a Member State key pair (MS.SK and MS.PK) shall be generated. Member States public keys shall be certified by the European Certification Authority. The Member State private key shall be used to certify public keys to be inserted in equipment (vehicle unit or tachograph card). Records of all certified public keys shall be kept with the identification of the equipment to which it is intended. These tasks shall be handled by a Member State Certification Authority. A Member State may regularly change its key pair.
 CSM_009 At equipment level, one single key pair (EQT.SK and EQT.PK) shall be generated and inserted in each equipment. Equipment public keys shall be certified by a Member State Certification Authority. These tasks may be handled by equipment manufacturers, equipment personalisers or Member State authorities. This key pair is used for authentication, digital signature and encipherement services
 CSM_010 
The following picture summarises the data flow of this process:


 3.1.2  CSM_011 For the purpose of equipment testing (including interoperability tests) the European Certification Authority shall generate a different single European test key pair and at least two Member State test key pairs, the public keys of which shall be certified with the European private test key. Manufacturers shall insert, in equipment undergoing type approval tests, test keys certified by one of these Member State test keys.
 3.1.3 
The confidentiality of the three Triple DES keys described below shall be appropriately maintained during generation, transport (if any) and storage.

In order to support tachograph components compliant with ISO 16844, the European Certification Authority and the Member State Certification Authorities shall, in addition, ensure the following:
 CSM_036 The European Certification authority shall generate KmVU and KmWC, two independent and unique Triple DES keys, and generate Km as: Km = KmVU XOR KmWC. The European Certification Authority shall forward these keys, under appropriately secured procedures, to Member States Certification Authorities at their request.
 CSM_037 

— use Km to encrypt motion sensor data requested by motion sensor manufacturers (data to be encrypted with Km is defined in ISO 16844-3),
— forward KmVU to vehicle unit manufacturers, under appropriately secured procedures, for insertion in vehicle units,
— ensure that KmWC will be inserted in all workshop cards ( in  elementary file) during card personalisation.
 3.1.4  CSM_012 Vehicle units and tachograph cards shall, as a part of the mutual authentication process, generate and exchange necessary data to elaborate a common Triple DES session key. This exchange of data shall be protected for confidentiality through an RSA crypt-mechanism.
 CSM_013 This key shall be used for all subsequent cryptographic operations using secure messaging. Its validity shall expire at the end of the session (withdrawal of the card or reset of the card) and/or after 240 use (one use of the key = one command using secure messaging sent to the card and associated response).
 3.2.  CSM_014 RSA keys shall have (whatever the level) the following lengths: modulus n1 024 bits, public exponent e 64 bits maximum, private exponent d1 024 bits.
 CSM_015 Triple DES keys shall have the form (Ka, Kb, Ka) where Ka and Kb are independent 64 bits long keys. No parity error detecting bits shall be set.
 3.3.  CSM_016 RSA Public key certificates shall be ‘non self-descriptive’‘Card Verifiable’ certificates (Ref.: ISO/IEC 7816-8)
 3.3.1  CSM_017 
Data Format Bytes Obs
CPI INTEGER 1 Certificate Profile Identifier (‘01’ for this version)
CAR OCTET STRING 8 Certification Authority Reference
CHA OCTET STRING 7 Certificate Holder Authorisation
EOV TimeReal 4 Certificate end of validity. Optional, ‘FF’ padded if not used.
CHR OCTET STRING 8 Certificate Holder Reference
n OCTET STRING 128 Public key (modulus)
e OCTET STRING 8 Public Key (public exponent)
 164  1. 
The headerlist associated with this certificate content is as follows:

‘4D’ ‘16’ ‘5F 29’ ‘01’ ‘42’ ‘08’ ‘5F 4B’ ‘07’ ‘5F 24’ ‘04’ ‘5F 20’ ‘08’ ‘7F 49’ ‘05’ ‘81’ ‘81 80’ ‘82’ ‘08’
Extended Headerlist Tag Length of header list CPI Tag CPI Length CAR Tag CAR Length CHA Tag CHA Length EOV Tag EOV Length CHR Tag CHR Length Public Key Tag (Constructed) Length of subsequent DOs modulus Tag modulus length public exponent Tag public exponent length

 2. The ‘Certification Authority Reference’ (CAR) has the purpose of identifying the certificate issuing CA, in such a way that the Data Element can be used at the same time as an Authority Key Identifier to reference the Public Key of the Certification Authority (for coding, see Key Identifier below).
 3. The ‘Certificate Holder Authorisation’ (CHA) is used to identify the rights of the certificate holder. It consists of the Tachograph Application ID and of the type of equipment to which the certificate is intended (according to  data element, ‘00’ for a Member State).
 4. The ‘Certificate Holder Reference’ (CHR) has the purpose of identifying uniquely the certificate holder, in such a way that the Data Element can be used at the same time as a Subject Key Identifier to reference the Public Key of the certificate holder.
 5. 

5.1 Equipment (VU or Card):

Data Equipment serial number Date Type Manufacturer
Length 4 Bytes 2 Bytes 1 Byte 1 Byte
Value Integer mm yy BCD coding Manufacturer specific Manufacturer codeIn the case of a VU, the manufacturer, when requesting certificates, may or may not know the identification of the equipment in which the keys will be inserted.
In the first case, the manufacturer will send the equipment identification with the public key to its Member State authority for certification. The certificate will then contain the equipment identification, and the manufacturer must ensure that keys and certificate are inserted in the intended equipment. The Key identifier has the form shown above.
In the later case, the manufacturer must uniquely identify each certificate request and send this identification with the public key to its Member State authority for certification. The certificate will contain the request identification. The manufacturer must feed back its Member State authority with the assignment of key to equipment (i.e. certificate request identification, equipment identification) after key installation in the equipment. The key identifier has the following form:
Data Certificate request serial number Date Type Manufacturer
Length 4 Bytes 2 Bytes 1 Byte 1 Byte
Value Integer mm yy BCD coding ‘FF’ Manufacturer code
5.2 Certification Authority:

Data Authority Identification Key serial number Additional info Identifier
Length 4 Bytes 1 Byte 2 Bytes 1 Byte
Value 1 Byte nation numerical code3 Bytes nation alphanumerical code Integer additional coding(CA specific)‘FF FF’ if not used ‘01’The key serial number is used to distinguish the different keys of a Member State, in the case the key is changed.
 6. Certificate verifiers shall implicitly know that the public key certified is an RSA key relevant to authentication, digital signature verification and encipherement for confidentiality services (the certificate contains no Object Identifier to specify it).
 3.3.2  CSM_018 
X.C = X.CA.SK[‘6A’ || Cr || Hash(Cc) || ‘BC’] || Cn || X.CAR

With certificate content = Cc = Cr || Cn
 106 bytes  58 bytes 1. This certificate is 194 bytes long.
 2. CAR, being hidden by the signature, is also appended to the signature, such that the Public Key of the Certification Authority may be selected for the verification of the certificate.
 3. The certificate verifier shall implicitly know the algorithm used by the Certification Authority to sign the certificate.
 4. 
‘7F 21’ ‘09’ ‘5F 37’ ‘81 80’ ‘5F 38’ ‘3A’ ‘42’ ‘08’
CV Certificate Tag (Constructed) Length of subsequent DOs Signature Tag Signature Length Remainder Tag Remainder Length CAR Tag CAR Length
 3.3.3 
Certificate verification and unwrapping consists in verifying the signature in accordance with ISO/IEC 9796-2, retrieving the certificate content and the public key contained: X.PK = X.CA.PK o X.C, and verifying the validity of the certificate.
 CSM_019 

 Verify signature and retrieve content:
 — from X.C retrieve Sign, Cn' and CAR':
 X.C = Sign || Cn' || CAR'
  128 Bytes  58 Bytes  8 Bytes
— from CAR' select appropriate Certification Authority Public Key (if not done before through other means)
— open Sign with CA Public Key: Sr'= X.CA.PK [Sign],
— check Sr' starts with ‘6A’ and ends with ‘BC’
 — compute Cr' and H' from: Sr' =
 ‘6A’ || Cr' || H' || ‘BC’
   106 Bytes  20 Bytes  
— Recover certificate content C' = Cr' || Cn',
— check Hash(C') = H'
 If the checks are OK the certificate is a genuine one, its content is C'.
 Verify validity. From C':
— if applicable, check End of validity date,
 Retrieve and store public key, Key Identifier, Certificate Holder Authorisation and Certificate End of Validity from C':
— X.PK = n || e
— X.KID = CHR
— X.CHA = CHA
— X.EOV = EOV
 4. 
Mutual authentication between cards and VUs is based on the following principle:

Each party shall demonstrate to the other that it owns a valid key pair, the public key of which has been certified by a Member State certification authority, itself being certified by the European certification authority.

Demonstration is made by signing with the private key a random number sent by the other party, who must recover the random number sent when verifying this signature.

The mechanism is triggered at card insertion by the VU. It starts with the exchange of certificates and unwrapping of public keys, and ends with the setting of a session key.
 CSM_020 



 5.  5.1.  CSM_021 VU-Cards data transfers integrity shall be protected through Secure Messaging in accordance with references [ISO/IEC 7816-4] and [ISO/IEC 7816-8].
 CSM_022 When data need to be protected during transfer, a Cryptographic Checksum Data Object shall be appended to the Data Objects sent within the command or the response. The Cryptographic Checksum shall be verified by the receiver.
 CSM_023 The cryptographic checksum of data sent within a command shall integrate the command header, and all data objects sent (=>CLA = ‘0C’, and all data objects shall be encapsulated with tags in which b1=1).
 CSM_024 The response status-information bytes shall be protected by a cryptographic checksum when the response contains no data field.
 CSM_025 
The structure of commands and responses when using secure messaging is therefore the following:


 The DOs used are a partial set of the Secure Messaging DOs described in ISO/IEC 7816-4:
Tag Mnemonic Meaning
‘81’ TPV Plain Value not BER-TLV coded data (to be protected by CC)
‘97’ TLE Value of Le in the unsecured command (to be protected by CC)
‘99’ TSW Status-Info (to be protected by CC)
‘8E’ TCC Cryptographic Checksum
‘87’ TPI CG Padding Indicator Byte || Cryptogram (Plain Value not coded in BER-TLV)
 Given an unsecured command response pair:
Command header Command body
CLA INS P1 P2 [Lc field] [Data field] [Le field]
four bytes L bytes, denoted as B1 to BL
Response body Response trailer
[Data field] SW1 SW2
Lr data bytes two bytes
 The corresponding secured command response pair is:
 Secured command:

Command header (CH) Command body
CLA INS P1 P2 [New Lc field] [New Data field] [New Le field]
‘OC’ Length of New Data field TPV LPV PV TLE LLE Le TCC LCC CC ‘00’
‘81’ Lc Data field ‘97’ ‘01’ Le ‘8E’ ‘04’ CCData to be integrated in checksum = CH || PB || TPV || LPV || PV || TLE || LLE || Le || PB
PB = Padding Bytes (80 .. 00) in accordance with ISO-IEC 7816-4 and ISO 9797 method 2.
DOs PV and LE are present only when there is some corresponding data in the unsecured command.
 Secured response:
1.. Case where response data field is not empty and needs not to be protected for confidentiality:

Response body Response trailer
[New Data field] new SW1 SW2
TPV LPV PV TCC LCC CC 
‘81’ Lr Data field ‘8E’ ‘04’ CCData to be integrated in checksum = TPV || LPV || PV || PB
2.. Case where response data field is not empty and needs to be protected for confidentiality:

Response body Response trailer
[New Data field] new SW1 SW2
TPI CG LPI CG PI CG TCC LCC CC 
‘87’  PI || CG ‘8E’ ‘04’ CCData to be carried by CG: non BER-TLV coded data and padding bytes.
Data to be integrated in checksum = TPI CG || LPI CG || PI CG || PB
3.. Case where response data field is empty:

Response body Response trailer
[New Data field] new SW1 SW2
TSW LSW SW TCC LCC CC 
‘99’ ‘02’ New SW1 SW2 ‘8E’ ‘04’ CCData to be integrated in checksum = TSW || LSW || SW || PB
 5.2.  CSM_026 
‘66 88’Verification of Cryptographic Checksum failed,‘69 87’Expected SM Data Objects missing,‘69 88’SM Data Objects incorrect.
 CSM_027 When the tachograph card returns status bytes without SM DOs or with an erroneous SM DO, the session must be aborted by the VU.
 5.3.  CSM_028 

— Initial stage: The initial check block y0 is E(Ka, SSC).
— Sequential stage: The check blocks y1, .., yn are calculated using Ka.
— Final stage: The cryptographic checksum is calculated from the last check block yn as follows: E(Ka, D(Kb, yn)).

where E() means encryption with DES, and D() means decryption with DES.

The four most significant bytes of the cryptographic checksum are transferred
 CSM_029 
Initial SSC: Rnd3 (4 least significant bytes) || Rnd1 (4 least significant bytes).
 CSM_030 
The following figure shows the calculation of the retail MAC:


 5.4.  CSM_031 
The following figure shows the application of keys in TDES:


 6.  CSM_032 The Intelligent Dedicated Equipment (IDE) stores data received from an equipment (VU or card) during one download session within one physical data file. This file must contain the certificates MSi.C and EQT.C. The file contains digital signatures of data blocks as specified in Appendix 7 Data Downloading Protocols.
 CSM_033 Digital signatures of downloaded data shall use a digital signature scheme with appendix such, that downloaded data may be read without any decipherment if desired.
 6.1.  CSM_034 

 Signature = EQT.SK[‘00’ || ‘01’ || PS || ‘00’ || DER(SHA-1(Data))]
 PS = Padding string of octets with value ‘FF’ such that length is 128.
 DER(SHA-1(M)) is the encoding of the algorithm ID for the hash function and the hash value into an ASN.1 value of type DigestInfo (distinguished encoding rules):
‘30’||‘21’||‘30’||‘09’||‘06’||‘05’||‘2B’||‘0E’||‘03’||‘02’||‘1A’||‘05’||‘00’||‘04’||‘14’||Hash Value.
 6.2.  CSM_035 
The European public key EUR.PK needs to be known independently (and trusted) by the verifier.

The following table illustrates the protocol an IDE carrying a Control card can follow to verify the integrity of data downloaded and stored on the ESM (External Storage media). The control card is used to perform the decipherement of digital signatures. This function may in this case not be implemented in the IDE.

The equipment that has downloaded and signed the data to be analysed is denoted EQT.


 PART B  7.  7.1. 
The following references are used in this part of this Appendix.

AESNational Institute of Standards and Technology (NIST), FIPS PUB 197: Advanced Encryption Standard (AES), November 26, 2001DSSNational Institute of Standards and Technology (NIST), FIPS PUB 186-4: Digital Signature Standard (DSS), July 2013ISO 7816-4ISO/IEC 7816-4, Identification cards — Integrated circuit cards — Part 4: Organization, security and commands for interchange. Third edition 2013-04-15ISO 7816-8ISO/IEC 7816-8, Identification cards — Integrated circuit cards — Part 8: Commands for security operations. Second edition 2004-06-01ISO 8825-1ISO/IEC 8825-1, Information technology — ASN.1 encoding rules: Specification of Basic Encoding Rules (BER), Canonical Encoding Rules (CER) and Distinguished Encoding Rules (DER). Fourth edition, 2008-12-15ISO 9797-1ISO/IEC 9797-1, Information technology — Security techniques — Message Authentication Codes (MACs) — Part 1: Mechanisms using a block cipher. Second edition, 2011-03-01ISO 10116ISO/IEC 10116, Information technology — Security techniques — Modes of operation of an n-bit block cipher. Third edition, 2006-02-01ISO 16844-3ISO/IEC 16844-3, Road vehicles — Tachograph systems — Part 3: Motion sensor interface. First edition 2004, including Technical Corrigendum 1 2006RFC 5480Elliptic Curve Cryptography Subject Public Key Information, March 2009RFC 5639Elliptic Curve Cryptography (ECC) — Brainpool Standard Curves and Curve Generation, 2010RFC 5869HMAC-based Extract-and-Expand Key Derivation Function (HKDF), May 2010SHSNational Institute of Standards and Technology (NIST), FIPS PUB 180-4: Secure Hash Standard, March 2012SP 800-38BNational Institute of Standards and Technology (NIST), Special Publication 800-38B: Recommendation for Block Cipher Modes of Operation: The CMAC Mode for Authentication, 2005TR-03111BSI Technical Guideline TR-03111, Elliptic Curve Cryptography, version 2.00, 2012-06-28
 7.2. 
The following notations and abbreviated terms are used in this Appendix:

AESAdvanced Encryption StandardCACertificate AuthorityCARCertificate Authority ReferenceCBCCipher Block Chaining (mode of operation)CHCommand HeaderCHACertificate Holder AuthorisationCHRCertificate Holder ReferenceCVConstant VectorDERDistinguished Encoding RulesDOData ObjectDSRCDedicated Short Range CommunicationECCElliptic Curve CryptographyECDSAElliptic Curve Digital Signature AlgorithmECDHElliptic Curve Diffie-Hellman (key agreement algorithm)EGFExternal GNSS FacilityEQTEquipmentIDEIntelligent Dedicated EquipmentKMMotion Sensor Master Key, allowing the pairing of a Vehicle Unit to a Motion SensorKM-VUKey inserted in vehicle units, allowing a VU to derive the Motion Sensor Master Key if a workshop card is inserted into the VUKM-WCKey inserted in workshop cards, allowing a VU to derive the Motion Sensor Master Key if a workshop card is inserted into the VUMACMessage Authentication CodeMoSMotion SensorMSBMost Significant BitPKIPublic Key InfrastructureRCFRemote Communication FacilitySSCSend Sequence CounterSMSecure MessagingTDESTriple Data Encryption StandardTLVTag Length ValueVUVehicle UnitX.Cthe public key certificate of user XX.CAthe certificate authority that issued the certificate of user XX.CARthe certificate authority reference mentioned in the certificate of user XX.CHRthe certificate holder reference mentioned in the certificate of user XX.PKpublic key of user XX.SKprivate key of user XX.PKephephemeral public key of user XX.SKephephemeral private key of user X‘xx’a hexadecimal value||concatenation operator
 7.3. 
The definitions of terms used in this Appendix are included in section I of Annex 1C.
 8.  8.1.  CSM_38 

— mutual authentication between a vehicle unit and a card,
— agreement of AES session keys between a vehicle unit and a card,
— ensuring the authenticity, integrity and non-repudiation of data downloaded from vehicle units or tachograph cards to external media.
 CSM_39 

— coupling of a vehicle unit and an external GNSS facility,
— mutual authentication between a vehicle unit and an external GNSS facility,
— agreement of an AES session key between a vehicle unit and an external GNSS facility.
 CSM_40 

— ensuring authenticity and integrity of data exchanged between a vehicle unit and a tachograph card,
— where applicable, ensuring confidentiality of data exchanged between a vehicle unit and a tachograph card.
 CSM_41 

— ensuring authenticity and integrity of data exchanged between a vehicle unit and an external GNSS facility.
 CSM_42 

— pairing of a vehicle unit and a motion sensor,
— mutual authentication between a vehicle unit and a motion sensor,
— ensuring confidentiality of data exchanged between a vehicle unit and a motion sensor.
 CSM_43 

— ensuring confidentiality, authenticity and integrity of data transmitted from a vehicle unit to a control card.
 — Properly speaking, data is transmitted from a vehicle unit to a remote interrogator under the control of a control officer, using a remote communication facility that may be internal or external to the VU, see Appendix 14. However, the remote interrogator sends the received data to a control card for decryption and validation of authenticity. From a security point of view, the remote communication facility and the remote interrogator are fully transparent.
 — A workshop card offers the same security services for the DSRC interface as a control card does. This allows a workshop to validate the proper functioning of the remote communication interface of a VU, including security. Please refer to section 9.2.2 for more information.
 8.2.  8.2.1  CSM_44 Vehicle units, tachograph cards, motion sensors and external GNSS facilities shall support the AES algorithm as defined in [AES], with key lengths of 128, 192 and 256 bits.
 8.2.2  CSM_45 Vehicle units, tachograph cards and external GNSS facilities shall support elliptic curve cryptography with a key size of 256, 384 and 512/521 bits.
 CSM_46 Vehicle units, tachograph cards and external GNSS facilities shall support the ECDSA signing algorithm, as specified in [DSS].
 CSM_47 Vehicle units, tachograph cards and external GNSS facilities shall support the ECKA-EG key agreement algorithm, as specified in [TR 03111].
 CSM_48 

Table 1
Standardized domain parameters
Name Size (bits) Reference Object identifier
NIST P-256 256 [DSS], [RFC 5480] 
BrainpoolP256r1 256 [RFC 5639] 
NIST P-384 384 [DSS], [RFC 5480] 
BrainpoolP384r1 384 [RFC 5639] 
BrainpoolP512r1 512 [RFC 5639] 
NIST P-521 521 [DSS], [RFC 5480] Note: the object identifiers mentioned in the last column of Table 1 are specified in [RFC 5639] for the Brainpool curves and in [RFC 5480] for the NIST curves. 8.2.3  CSM_49 Vehicle units, tachograph cards and external GNSS facilities shall support the SHA-256, SHA-384 and SHA-512 algorithms specified in [SHS].
 8.2.4  CSM_50 

Table 2
Allowed cipher suites
Cipher suite Id ECC key size (bits) AES key length (bits) Hashing algorithm MAC length (bytes)
CS#1 256 128 SHA-256 8
CS#2 384 192 SHA-384 12
CS#3 512/521 256 SHA-512 16Note: ECC keys sizes of 512 bits and 521 bits are considered to be equal in strength for all purposes within this Appendix. 9.  9.1.  9.1.1 Note: the keys described in this section are used for mutual authentication and secure messaging between vehicle units and tachograph cards and between vehicle units and external GNSS facilities. These processes are described in detail in chapters 10 and 11 of this Appendix. CSM_51 

— European level,
— Member State level,
— Equipment level.
 CSM_52 Within the entire European Smart Tachograph system, public and private keys and certificates shall be generated, managed and communicated using standardized and secure methods.
 9.1.2  CSM_53 At European level, a single unique ECC key pair designated as EUR shall be generated. It shall consist of a private key (EUR.SK) and a public key (EUR.PK). This key pair shall form the root key pair of the entire European Smart Tachograph PKI. This task shall be handled by a European Root Certificate Authority (ERCA), under the authority and responsibility of the European Commission.
 CSM_54 The ERCA shall use the European private key to sign a (self-signed) root certificate of the European public key, and shall communicate this European root certificate to all Member States.
 CSM_55 The ERCA shall use the European private key to sign the certificates of the Member States public keys upon request. The ERCA shall keep records of all signed Member State public key certificates.
 CSM_56 Note: The introduction of a new root key pair also implies that ERCA will generate a new motion sensor master key and a new DSRC master key, see sections 9.2.1.2 and 9.2.2.2. CSM_57 Before generating a new European root key pair, the ERCA shall conduct an analysis of the cryptographic strength that is needed for the new key pair, given it should stay secure for the next 34 years. If found necessary, the ERCA shall switch to a cipher suite that is stronger than the current one, as specified in CSM_50.
 CSM_58 Note: Since a link certificate contains the ERCA generation X public key and is signed with the ERCA generation X-1 private key, a link certificate offers equipment issued under generation X-1 a method to trust equipment issued under generation X. CSM_59 The ERCA shall not use the private key of a root key pair for any purpose after the moment a new root key certificate becomes valid.
 CSM_60 

— The current EUR key pair and corresponding certificate
— All previous EUR certificates to be used for the verification of MSCA certificates that are still valid
— Link certificates for all generations of EUR certificates except the first one
 9.1.3  CSM_61 At Member State level, all Member States required to sign tachograph card certificates shall generate one or more unique ECC key pairs designated as MSCA_Card. All Member States required to sign certificates for vehicle units or external GNSS facilities shall additionally generate one or more unique ECC key pairs designated as MSCA_VU-EGF.
 CSM_62 The task of generating Member State key pairs shall be handled by a Member State Certificate Authority (MSCA). Whenever a MSCA generates a Member State key pair, it shall send the public key to the ERCA in order to obtain a corresponding Member State certificate signed by the ERCA.
 CSM_63 An MSCA shall choose the strength of a Member State key pair equal to the strength of the European root key pair used to sign the corresponding Member State certificate.
 CSM_64 An MSCA_VU-EGF key pair, if present, shall consist of private key MSCA_VU-EGF.SK and public key MSCA_VU-EGF.PK. An MSCA shall use the MSCA_VU-EGF.SK private key exclusively to sign the public key certificates of vehicle units and external GNSS facilities.
 CSM_65 An MSCA_Card key pair shall consist of private key MSCA_Card.SK and public key MSCA_Card.PK. An MSCA shall use the MSCA_Card.SK private key exclusively to sign the public key certificates of tachograph cards.
 CSM_66 An MSCA shall keep records of all signed VU certificates, external GNSS facility certificates and card certificates, together with the identification of the equipment for which each certificate is intended.
 CSM_67 The validity period of an MSCA_VU-EGF certificate shall be 17 years plus 3 months. The validity period of an MSCA_Card certificate shall be 7 years plus 1 month.
 CSM_68 As shown in Figure 1 in section 9.1.7, the private key of a MSCA_VU-EGF key pair and the private key of a MSCA_Card key pair shall have a key usage period of two years.
 CSM_69 An MSCA shall not use the private key of an MSCA_VU-EGF key pair for any purpose after the moment its usage period has ended. Neither shall an MSCA use the private key of an MSCA_Card key pair for any purpose after the moment its usage period has ended.
 CSM_70 

— The current MSCA_Card key pair and corresponding certificate
— All previous MSCA_Card certificates to be used for the verification of the certificates of tachograph cards that are still valid
— The current EUR certificate necessary for the verification of the current MSCA certificate
— All previous EUR certificates necessary for the verification of all MSCA certificates that are still valid
 CSM_71 

— The current MSCA_VU-EGF key pair and corresponding certificate
— All previous MSCA_VU-EGF public keys to be used for the verification of the certificates of VUs or external GNSS facilities that are still valid
 9.1.4  CSM_72 Two unique ECC key pairs shall be generated for each vehicle unit, designated as VU_MA and VU_Sign. This task is handled by VU manufacturers. Whenever a VU key pair is generated, the party generating the key shall send the public key to its MSCA, in order to obtain a corresponding VU certificate signed by the MSCA. The private key shall be used only by the vehicle unit.
 CSM_73 The VU_MA and VU_Sign certificates of a given vehicle unit shall have the same Certificate Effective Date.
 CSM_74 A VU manufacturer shall choose the strength of a VU key pair equal to the strength of the MSCA key pair used to sign the corresponding VU certificate.
 CSM_75 A vehicle unit shall use its VU_MA key pair, consisting of private key VU_MA.SK and public key VU_MA.PK, exclusively to perform VU Authentication towards tachograph cards and external GNSS facilities, as specified in sections 10.3 and 11.4 of this Appendix.
 CSM_76 A vehicle unit shall be capable of generating ephemeral ECC key pairs and shall use an ephemeral key pair exclusively to perform session key agreement with a tachograph card or external GNSS facility, as specified in sections 10.4 and 11.4 of this Appendix.
 CSM_77 A vehicle unit shall use the private key VU_Sign.SK of its VU_Sign key pair exclusively to sign downloaded data files, as specified in chapter 14 of this Appendix. The corresponding public key VU_Sign.PK shall be used exclusively to verify signatures created by the vehicle unit.
 CSM_78  — The extended validity period of a VU_Sign certificate allows a Vehicle Unit to create valid signatures over downloaded data during the first three months after it has expired, as required in Regulation (EU) No 581/2010.
 — The extended validity period of a VU_MA certificate is needed to allow the VU to authenticate to a control card or a company card during the first three months after it has expired, such that is it possible to perform a data download.
 CSM_79 A vehicle unit shall not use the private key of a VU key pair for any purpose after the corresponding certificate has expired.
 CSM_80  — Ephemeral key pairs are not included in this requirement, as a new ephemeral key pair is generated by a VU each time Chip Authentication and session key agreement is performed, see section 10.4. Note that ephemeral key pairs do not have corresponding certificates.
 — This requirement does not forbid the possibility of replacing static VU key pairs during a refurbishment or repair in a secure environment controlled by the VU manufacturer.
 CSM_81 

— The VU_MA private key and corresponding certificate
— The VU_Sign private key and corresponding certificate
— The MSCA_VU-EGF certificate containing the MSCA_VU-EGF.PK public key to be used for verification of the VU_MA certificate and VU_Sign certificate
— The EUR certificate containing the EUR.PK public key to be used for verification of the MSCA_VU-EGF certificate
— The EUR certificate whose validity period directly precedes the validity period of the EUR certificate to be used to verify the MSCA_VU-EGF certificate, if existing
— The link certificate linking these two EUR certificates, if existing
 CSM_82 In addition to the cryptographic keys and certificates listed in CSM_81, vehicle units shall also contain the keys and certificates specified in Part A of this Appendix, allowing a vehicle unit to interact with first-generation tachograph cards.
 9.1.5  CSM_83 One unique ECC key pair, designated as Card_MA, shall be generated for each tachograph card. A second unique ECC key pair, designated as Card_Sign, shall additionally be generated for each driver card and each workshop card. This task may be handled by card manufacturers or card personalisers. Whenever a card key pair is generated, the party generating the key shall send the public key to its MSCA, in order to obtain a corresponding card certificate signed by the MSCA. The private key shall be used only by the tachograph card.
 CSM_84 The Card_MA and Card_Sign certificates of a given driver card or workshop card shall have the same Certificate Effective Date.
 CSM_85 A card manufacturer or card personaliser shall choose the strength of a card key pair equal to the strength of the MSCA key pair used to sign the corresponding card certificate.
 CSM_86 A tachograph card shall use its Card_MA key pair, consisting of private key Card_MA.SK and public key Card_MA.PK, exclusively to perform mutual authentication and session key agreement towards vehicle units, as specified in sections 10.3 and 10.4 of this Appendix.
 CSM_87 A driver card or workshop card shall use the private key Card_Sign.SK of its Card_Sign key pair exclusively to sign downloaded data files, as specified in chapter 14 of this Appendix. The corresponding public key Card_Sign.PK shall be used exclusively to verify signatures created by the card.
 CSM_88 

— For driver cards: 5 years
— For company cards: 5 years
— For control cards: 2 years
— For workshop cards: 1 year
 CSM_89 
 — For driver cards:
 5 years and 1 month
 — For workshop cards:
 1 year and 1 monthNote: the extended validity period of a Card_Sign certificate allows a driver card to create valid signatures over downloaded data during the first month after it has expired. This is necessary in view of Regulation (EU) No 581/2010, which requires that a data download from a driver card must be possible up to 28 days after the last data has been recorded. CSM_90 The key pairs and corresponding certificates of a given tachograph card shall not be replaced or renewed once the card has been issued.
 CSM_91 
— The Card_MA private key and corresponding certificate
— For driver cards and workshop cards additionally: the Card_Sign private key and corresponding certificate
— The MSCA_Card certificate containing the MSCA_Card.PK public key to be used for verification of the Card_MA certificate and Card_Sign certificate
— The EUR certificate containing the EUR.PK public key to be used for verification of the MSCA_Card certificate.
— The EUR certificate whose validity period directly precedes the validity period of the EUR certificate to be used to verify the MSCA_Card certificate, if existing.
— The link certificate linking these two EUR certificates, if existing.
— Additionally, for control cards, company cards and workshop cards only, and only if such cards are issued during the first three months of the validity period of a new EUR certificate: the EUR certificate that is two generations older, if existing.
                                                Note to last bullet:
                                              For example, in the first three months of the ERCA(3) certificate (see Figure 1), the mentioned cards shall contain the ERCA(1) certificate. This is needed to ensure that these cards can be used to perform data downloads from ERCA(1) VUs whose normal 15-year life period plus the 3-months data downloading period expires during these months; see the last bullet of requirement 13) in Annex IC. CSM_92 In addition to the cryptographic keys and certificates listed in CSM_91, tachograph cards shall also contain the keys and certificates specified in Part A of this Appendix, allowing these cards to interact with first-generation VUs.
 9.1.6  CSM_93 One unique ECC key pair shall be generated for each external GNSS facility, designated as EGF_MA. This task is handled by external GNSS facility manufacturers. Whenever an EGF_MA key pair is generated, the party generating th e key shall send the public key to its MSCA in order to obtain a corresponding EGF_MA certificate signed by the MSCA. The private key shall be used only by the external GNSS facility.
 CSM_94 An EGF manufacturer shall choose the strength of an EGF_MA key pair equal to the strength of the MSCA key pair used to sign the corresponding EGF_MA certificate.
 CSM_95 An external GNSS facility shall use its EGF_MA key pair, consisting of private key EGF_MA.SK and public key EGF_MA.PK, exclusively to perform mutual authentication and session key agreement towards vehicle units, as specified in section 11.4 of this Appendix.
 CSM_96 The validity period of an EGF_MA certificate shall be 15 years.
 CSM_97 Note: as explained in section 11.3.3, an EGF may potentially use its private key for mutual authentication towards the VU it is already coupled to, even after the corresponding certificate has expired. CSM_98 Note: This requirement does not forbid the possibility of replacing EGF key pairs during a refurbishment or repair in a secure environment controlled by the EGF manufacturer. CSM_99 

— The EGF_MA private key and corresponding certificate
— The MSCA_VU-EGF certificate containing the MSCA_VU-EGF.PK public key to be used for verification of the EGF_MA certificate
— The EUR certificate containing the EUR.PK public key to be used for verification of the MSCA_VU-EGF certificate
— The EUR certificate whose validity period directly precedes the validity period of the EUR certificate to be used to verify the MSCA_VU-EGF certificate, if existing
— The link certificate linking these two EUR certificates, if existing
 9.1.7 
Figure 1 below shows how different generations of ERCA root certificates, ERCA link certificates, MSCA certificates and equipment (VU and card) certificates are issued and used over time:
 Figure 1
                                        

 1. Different generations of the root certificate are indicated by a number in brackets. E.g. ERCA (1) is the first generation of ERCA root certificate; ERCA (2) is the second generation, etc.
 2. Other certificates are indicated by two numbers in brackets, the first one indicating the root certificate generation under which they are issued, the second one the generation of the certificate itself. E.g. MSCA_Card (1-1) is the first MSCA_Card certificate issued under ERCA (1); MSCA_Card (2-1) is the first MSCA_Card certificate issued under ERCA (2); MSCA_Card (2-last) is the last MSCA_Card certificate issued under ERCA (2); Card_MA(2-1) is the first Card certificate for mutual authentication that is issued under ERCA (2), etc.
 3. The MSCA_Card (2-1) and MSCA_Card (1-last) certificates are issued at almost but not exactly the same date. MSCA_Card (2-1) is the first MSCA_Card certificate issued under ERCA (2) and will be issued slightly later than MSCA_Card (1-last), the last MSCA_Card certificate under ERCA (1).
 4. As shown in the figure, the first VU and Card certificates issued under ERCA (2) will appear almost two years before the last VU and Card certificates issued under ERCA (1) will appear. This is because of the fact that VU and Card certificates are issued under an MSCA certificate, not directly under the ERCA certificate. The MSCA (2-1) certificate will be issued directly after ERCA (2) becomes valid, but the MSCA (1-last) certificate will be issued only slightly before that time, at the last moment the ERCA (1) certificate is still valid. Therefore, these two MSCA certificates will have almost the same validity period, despite the fact that they are of different generations.
 5. The validity period shown for cards is the one for driver cards (5 years).
 6. To save space, the difference in validity period between the Card_MA and Card_Sign certificates is shown only for the first generation.
 9.2.  9.2.1  9.2.1.1 Note: readers of this section are supposed to be familiar with the contents of [ISO 16844-3] describing the interface between a vehicle unit and a motion sensor. The pairing process between a VU and a motion sensor is described in detail in chapter 12 of this Appendix. CSM_100 

Table 3
Keys for securing vehicle unit — motion sensor communication
Key Symbol Generated by Generation method Stored by
Motion Sensor Master Key — VU part KM-VU ERCA Random ERCA, MSCAs involved in issuing VUs certificates, VU manufacturers, vehicle units
Motion Sensor Master Key — Workshop part KM-WC ERCA Random ERCA, MSCAs, card manufacturers, workshop cards
Motion Sensor Master Key KM Not independently generated Calculated as KM = KM-VU XOR KM-WC ERCA, MSCAs involved in issuing motion sensors keys (optionally)
Identification Key KID Not independently generated Calculated as KID = KM XOR CV, where CV is specified in CSM_106 ERCA, MSCAs involved in issuing motion sensors keys (optionally)
Pairing Key KP Motion sensor manufacturer Random One motion sensor
Session Key KS VU (during pairing of VU and motion sensor) Random One VU and one motion sensor
 CSM_101 The European Root Certificate Authority shall generate KM-VU and KM-WC, two random and unique AES keys from which the motion sensor master key KM can be calculated as KM-VU XOR KM-WC. The ERCA shall communicate KM, KM-VU and KM-WC to Member State Certificate Authorities upon their request.
 CSM_102 Note: The version number is used to distinguish different generations of these keys, as explained in detail in section 9.2.1.2. CSM_103 A Member State Certificate Authority shall forward KM-VU, together with its version number, to vehicle unit manufacturers upon their request. The VU manufacturers shall insert KM-VU and its version number in all manufactured VUs.
 CSM_104  — See the description of data type  in Appendix 2.
 — as explained in section 9.2.1.2, in fact multiple generations of KM-WC may have to be inserted in a single workshop card.
 CSM_105  — This allows a second-generation workshop card to be used for coupling a first-generation VU.
 — A second-generation workshop card will contain two different applications, one complying with Part B of this Appendix and one complying with Part A. The latter will contain the TDES key KmWC.
 CSM_106 

— For 128-bit motion sensor master keys: CV = ‘B6 44 2C 45 0E F8 D3 62 0B 7A 8A 97 91 E4 5D 83’
— For 192-bit motion sensor master keys: CV = ‘72 AD EA FA 00 BB F4 EE F4 99 15 70 5B 7E EE BB 1C 54 ED 46 8B 0E F8 25’
— For 256-bit motion sensor master keys: CV = ‘1D 74 DB F0 34 C7 37 2F 65 55 DE D5 DC D1 9A C3 23 D6 A6 25 64 CD BE 2D 42 0D 85 D2 32 63 AD 60’
Note: the constant vectors have been generated as follows:
 Pi_10 = first 10 bytes of the decimal portion of the mathematical constant π = ‘24 3F 6A 88 85 A3 08 D3 13 19’
 CV_128-bits = first 16 bytes of SHA-256(Pi_10)
 CV_192-bits = first 24 bytes of SHA-384(Pi_10)
 CV_256-bits = first 32 bytes of SHA-512(Pi_10) CSM_107 Note: as explained in section 9.2.1.2, in fact a motion sensor manufacturer may have to generate multiple unique pairing keys for a single motion sensor. CSM_108 Each motion sensor manufacturer shall generate a unique serial number for every motion sensor, and shall send all serial numbers to its Member State Certificate Authority. The MSCA shall encrypt each serial number separately with the identification key K
                                                ID
                                              and shall return the encrypted serial number to the motion sensor manufacturer. For each encrypted serial number, the MSCA shall notify the motion sensor manufacturer of the version number of the associated K
                                                ID
                                             .
 CSM_109 For requirements CSM_107 and CSM_108, the MSCA shall use the AES algorithm in the Cipher Block Chaining mode of operation, as defined in [ISO 10116], with an interleave parameter m = 1 and an initialization vector SV = ‘00’ {16}, i.e. sixteen bytes with binary value 0. When necessary, the MSCA shall use padding method 2 defined in [ISO 9797-1].
 CSM_110 Note: as explained in section 9.2.1.2, in fact a motion sensor manufacturer may have to insert multiple encrypted pairing keys and multiple encrypted serial numbers in a single motion sensor. CSM_111 Note: doing so will allow a second-generation motion sensor to be coupled to a first-generation VU. CSM_112 The length of the session key KS generated by a VU during the pairing to a motion sensor shall be linked to the length of its KM-VU, as described in CSM_50.
 9.2.1.2  CSM_113 
Figure 2 CSM_114 At least one year before generating a new European root key pair, as described in CSM_56, the ERCA shall generate a new motion sensor master key KM by generating a new KM-VU and KM-WC. The length of the motion sensor master key shall be linked to the foreseen strength of the new European root key pair, according to CSM_50. The ERCA shall communicate the new KM, KM-VU and KM-WC to the MSCAs upon their request, together with their version number.
 CSM_115 Note: this implies that in the last year of the validity period of an ERCA certificate, workshop cards will be issued with three different generations of KM-WC, as shown in Figure 2. CSM_116 Note: This implies that in the last year of the validity period of an ERCA certificate, motion sensors will be issued with encrypted data based on three different generations of KM, as shown in Figure 2. CSM_117 Note: In case the motion sensor manufacturer chooses to generate a TDES-based pairing key for a second-generation motion sensor (see CSM_111), the manufacturer shall indicate to the MSCA that the TDES-based motion sensor master key must be used for encrypting this pairing key. This is because the length of a TDES key may be equal to that of an AES key, so the MSCA cannot judge from the key length alone. CSM_118  — A vehicle unit based on the generation X ERCA certificate shall only contain the generation X KM-VU, even if it is issued after the start of the validity period of the generation X+1 ERCA certificate. This is shown in Figure 2.
 — A VU of generation X cannot be paired to a motion sensor of generation X-1.
 — Since workshop cards have a validity period of one year, the result of CSM_113 — CSM_118 is that all workshop cards will contain the new KM-WC at the moment the first VU containing the new KM-VU is issued. Therefore, such a VU will always be able to calculate the new KM. Moreover, by that time most new motion sensors will contain encrypted data based on the new KM as well.
 9.2.2  9.2.2.1  CSM_119 The authenticity and confidentiality of data communicated from a vehicle unit to a control authority over a DSRC remote communication channel shall be ensured by means of a set of VU-specific AES keys derived from a single DSRC master key, KMDSRC.
 CSM_120 The DSRC master key KMDSRC shall be an AES key that is securely generated, stored and distributed by the ERCA. The key length may be 128, 192 or 256 bits and shall be linked to the length of the European root key pair, as described in CSM_50.
 CSM_121 The ERCA shall communicate the DSRC master key to Member State Certificate Authorities upon their request in a secure manner, to allow them to derive VU-specific DSRC keys and to ensure that the DSRC master key is inserted in all control cards and workshop cards issued under their responsibility.
 CSM_122 Note: The version number is used to distinguish different generations of the DSRC master key, as explained in detail in section 9.2.2.2. CSM_123 
— This VU serial number shall be identical to the vuSerialNumber element of VuIdentification, see Appendix 1 and to the Certificate Holder Reference in the VU’s certificates.
— The VU serial number may not be known at the moment a vehicle unit manufacturer requests the VU-specific DSRC keys. In this case, the VU manufacturer shall send instead the unique certificate request ID it used when requesting the VU’s certificates; see CSM_153. This certificate request ID shall therefore be equal to the Certificate Holder Reference in the VU’s certificates. CSM_124 

 Step 1 (Extract):
— PRK = HMAC-Hash (salt, IKM) where salt is an empty string ‘’ and IKM is KMDSRC.
 Step 2 (Expand):
— OKM = T(1), where
T(1) = HMAC-Hash (PRK, T(0) || info || ‘01’) with
— T(0) = an empty string (‘’)
— info
                                                                   = VU serial number or certificate request ID, as specified in CSM_123
— K_VUDSRC_ENC = first L octets of OKM and
K_VUDSRC_MAC = last L octets of OKM
where L is the required length of K_VUDSRC_ENC and K_VUDSRC_MAC in octets.
 CSM_125 The MSCA shall distribute K_VUDSRC_ENC and K_VUDSRC_MAC to the VU manufacturer in a secure manner for insertion in the intended vehicle unit.
 CSM_126 When issued, a vehicle unit shall have stored K_VUDSRC_ENC and K_VUDSRC_MAC in its secure memory, in order to be able to ensure the integrity, authenticity and confidentiality of data sent over the remote communication channel. A vehicle unit shall also store the version number of the DSRC master key used to derive these VU-specific keys.
 CSM_127 Note: as explained in section 9.2.2.2, in fact multiple generations of KMDSRC may have to be inserted in a single workshop card or control card. CSM_128 The MSCA shall keep records of all VU-specific DSRC keys it generated, their version number and the VU serial number or certificate request ID used in deriving them.
 9.2.2.2  CSM_129 
Figure 3 CSM_130 At least two years before generating a new European root key pair, as described in CSM_56, the ERCA shall generate a new DSRC master key. The length of the DSRC key shall be linked to the foreseen strength of the new European root key pair, according to CSM_50. The ERCA shall communicate the new DSRC master key to the MSCAs upon their request, together with its version number.
 CSM_131 Note: this implies that in the last two years of the validity period of an ERCA certificate, control cards will be issued with three different generations of KMDSRC, as shown in Figure 3. CSM_132 Note: this implies that in the last year of the validity period of an ERCA certificate, workshop cards will be issued with three different generations of KMDSRC, as shown in Figure 3. CSM_133  — This implies that a vehicle unit based on the generation X ERCA certificate shall only contain the generation X K_VUDSRC_ENC and K_VUDSRC_MAC, even if the VU is issued after the start of the validity period of the generation X+1 ERCA certificate. This is shown in Figure 3.
 — Since workshop cards have a validity period of one year and control cards of two years, the result of CSM_131 — CSM_133 is that all workshop cards and control cards will contain the new DSRC master key at the moment the first VU containing VU-specific keys based on that master key will be issued.
 9.3.  9.3.1  CSM_134 All certificates in the European Smart Tachograph system shall be self-descriptive, card-verifiable (CV) certificates according to [ISO 7816-4] and [ISO 7816-8].
 CSM_135 Note: this encoding results in a Tag-Length-Value (TLV) structure as follows:TagThe tag is encoded in one or two octets and indicates the content.LengthThe length is encoded as an unsigned integer in one, two, or three octets, resulting in a maximum length of 65 535 octets. The minimum number of octets shall be used.ValueThe value is encoded in zero or more octets 9.3.2  CSM_136 

Table 4
Certificate Profile version 1
Field Field ID Tag Length (bytes) ASN.1 data type(see Appendix 1)
ECC Certificate C ‘7F 21’ var 
ECC Certificate Body B ‘7F 4E’ var 
Certificate Profile Identifier CPI ‘5F 29’ ‘01’ 
Certificate Authority Reference CAR ‘42’ ‘08’ 
Certificate Holder Authorisation CHA ‘5F 4C’ ‘07’ 
Public Key PK ‘7F 49’ var 
Domain Parameters DP ‘06’ var 
Public Point PP ‘86’ var 
Certificate Holder Reference CHR ‘5F 20’ ‘08’ 
Certificate Effective Date CEfD ‘5F 25’ ‘04’ 
Certificate Expiration Date CExD ‘5F 24’ ‘04’ 
ECC Certificate Signature S ‘5F 37’ var Note: the Field ID will be used in later sections of this Appendix to indicate individual fields of a certificate, e.g. X.CAR is the Certificate Authority Reference mentioned in the certificate of user X. 9.3.2.1  CSM_137 Certificates shall use a Certificate Profile Identifier to indicate the certificate profile used. Version 1, as specified in Table 4, shall be identified by a value of ‘00’.
 9.3.2.2  CSM_138 The Certificate Authority Reference shall be used to identify the public key to be used to verify the certificate signature. The Certificate Authority Reference shall therefore be equal to the Certificate Holder Reference in the certificate of the corresponding certificate authority.
 CSM_139 An ERCA root certificate shall be self-signed, i.e., the Certificate Authority Reference and the Certificate Holder Reference in the certificate shall be equal.
 CSM_140 For an ERCA link certificate, the Certificate Holder Reference shall be equal to the CHR of the new ERCA root certificate. The Certificate Authority Reference for a link certificate shall be equal to the CHR of the previous ERCA root certificate.
 9.3.2.3  CSM_141 The Certificate Holder Authorisation shall be used to identify the type of certificate. It consists of the six most significant bytes of the Tachograph Application ID, concatenated with the equipment type, which indicates the type of equipment for which the certificate is intended. In the case of a VU certificate, a driver card certificate or a workshop card certificate, the equipment type is also used to differentiate between a certificate for Mutual Authentication and a certificate for creating digital signatures (see section 9.1 and Appendix 1, data type EquipmentType).
 9.3.2.4 
The Public Key nests two data elements: the standardized domain parameters to be used with the public key in the certificate and the value of the public point.
 CSM_142 The data element Domain Parameters shall contain one of the object identifiers specified in Table 1 to reference a set of standardized domain parameters.
 CSM_143 The data element Public Point shall contain the public point. Elliptic curve public points shall be converted to octet strings as specified in [TR-03111]. The uncompressed encoding format shall be used. When recovering an elliptic curve point from its encoded format, the validations described in [TR-03111] shall always be carried out.
 9.3.2.5  CSM_144 The Certificate Holder Reference is an identifier for the public key provided in the certificate. It shall be used to reference this public key in other certificates.
 CSM_145 For card certificates and external GNSS facility certificates, the Certificate Holder Reference shall have the  data type specified in Appendix 1.
 CSM_146 Note:
                                                 For a card certificate, the value of the CHR shall be equal to the value of the cardExtendedSerialNumber in EF_ICC; see Appendix 2. For an EGF certificate, the value of the CHR shall be equal to the value of the sensorGNSSSerialNumber in EF_ICC; see Appendix 14. For a VU certificate, the value of the CHR shall be equal to the vuSerialNumber element of VuIdentification, see Appendix 1, unless the manufacturer does not know the manufacturer-specific serial number at the time the certificate is requested. CSM_147 For ERCA and MSCA certificates, the Certificate Holder Reference shall have the  data type specified in Appendix 1.
 9.3.2.6  CSM_148 The Certificate Effective Date shall indicate the starting date and time of the validity period of the certificate.
 9.3.2.7  CSM_149 The Certificate Expiration Date shall indicate the end date and time of the validity period of the certificate.
 9.3.2.8  CSM_150 The signature on the certificate shall be created over the encoded certificate body, including the certificate body tag and length. The signature algorithm shall be ECDSA, as specified in [DSS], using the hashing algorithm linked to the key size of the signing authority, as specified in CSM_50. The signature format shall be plain, as specified in [TR-03111].
 9.3.3  CSM_151 

— The Certificate Profile Identifier of the requested certificate
— The Certificate Authority Reference expected to be used for signing the certificate.
— The Public Key to be signed
 CSM_152 

— The numerical nation code of the Certification Authority (data type  defined in Appendix 1)
— The alphanumerical nation code of the Certification Authority (data type  defined in Appendix 1)
— The 1-byte serial number to distinguish the different keys of the Certification Authority in the case keys are changed
— The two-byte field containing Certification Authority specific additional info
 CSM_153 

— If known (see CSM_154), a serial number for the equipment, unique for the manufacturer, the equipment's type and the month of manufacturing. Otherwise, a unique certificate request identifier.
— The month and the year of equipment manufacturing or of the certificate request.

The manufacturer shall ensure that this data is correct and that the certificate returned by the MSCA is inserted in the intended equipment.
 CSM_154 In the case of a VU, the manufacturer, when requesting a certificate, may or may not know the manufacturer-specific serial number of the VU for which that certificate and the associated private key is intended. If known, the VU manufacturer shall send the serial number to the MSCA. If not known, the manufacturer shall uniquely identify each certificate request and send this certificate request serial number to the MSCA. The resulting certificate will then contain the certificate request serial number. After inserting the certificate in a specific VU, the manufacturer shall communicate the connection between the certificate request serial number and the VU identification to the MSCA.
 10.  10.1.  CSM_155 

— First, each party shall demonstrate to the other that it owns a valid public key certificate, signed by a Member State Certificate Authority. In turn, the MSCA public key certificate must be signed by the European root certificate authority. This step is called certificate chain verification and is specified in detail in section 10.2
— Second, the vehicle unit shall demonstrate to the card that it is in possession of the private key corresponding to the public key in the presented certificate. It does so by signing a random number sent by the card. The card verifies the signature over the random number. If this verification is successful, the VU is authenticated. This step is called VU Authentication and is specified in detail in section 10.3.
— Third, both parties independently calculate two AES session keys using an asymmetric key agreement algorithm. Using one of these session keys, the card creates a message authentication code (MAC) over some data sent by the VU. The VU verifies the MAC. If this verification is successful, the card is authenticated. This step is called Card Authentication and is specified in detail in section 10.4.
— Fourth, the VU and the card shall use the agreed session keys to ensure the confidentiality, integrity and authenticity of all exchanged messages. This is called Secure Messaging and is specified in detail in section 10.5.
 CSM_156 The mechanism described in CSM_155 shall be triggered by the vehicle unit whenever a card is inserted into one of its card slots.
 10.2.  10.2.1  CSM_157 

— The CHA field of the Card certificate shall indicate a card certificate for mutual authentication (see Appendix 1, data type EquipmentType).
— The CHA of the Card.CA certificate shall indicate an MSCA.
— The CHA of the Card.Link certificate shall indicate the ERCA.
 — The Card certificates and public keys mentioned in the figure are those for mutual authentication. Section 9.1.5 denotes these as Card_MA.
 — The Card.CA certificates and public keys mentioned in the figure are those for signing card certificates and it is indicated in the CAR of the Card certificate. Section 9.1.3 denotes these as MSCA_Card.
 — The Card.CA.EUR certificate mentioned in the figure is the European root certificate that is indicated in the CAR of the Card.CA certificate.
 — The Card.Link certificate mentioned in the figure is the card's link certificate, if present. As specified in section 9.1.2, this is a link certificate for a new European root key pair created by the ERCA and signed by the previous European private key.
 — The Card.Link.EUR certificate is the European root certificate that is indicated in the CAR of the Card.Link certificate.
 CSM_158 Note: There are three ways in which the VU may know the Card.CA.EUR certificate:
— the Card.CA.EUR certificate is the same certificate as the VU's own EUR certificate;
— the Card.CA.EUR certificate precedes the VU's own EUR certificate and the VU contained this certificate already at issuance (see CSM_81);
— the Card.CA.EUR certificate succeeds the VU's own EUR certificate and the VU received a link certificate in the past from another tachograph card, verified it and stored it for future reference. CSM_159 As indicated in Figure 4, once the VU has verified the authenticity and validity of a previously unknown certificate, it may store this certificate for future reference, such that it does not need to verify that certificate's authenticity again if it is presented to the VU again. Instead of storing the entire certificate, a VU may choose to store only the contents of the Certificate Body, as specified in section 9.3.2. Whereas storing of all other types of certificate is optional, it is mandatory for a VU to store a new link certificate presented by a card.
 CSM_160 The VU shall verify the temporal validity of any certificate read from the card or stored in its memory, and shall reject expired certificates. For verifying the temporal validity of a certificate presented by the card a VU shall use its internal clock.

Figure 4 10.2.2  CSM_161 

— The CHA of the VU.Link certificate shall indicate the ERCA.
— The CHA of the VU.CA certificate shall indicate an MSCA.
— The CHA field of the VU certificate shall indicate a VU certificate for mutual authentication (see Appendix 1, data type EquipmentType).

Figure 5 — The VU certificates and public keys mentioned in the figure are those for mutual authentication. Section 9.1.4 denotes these as VU_MA.
 — The VU.CA certificates and public keys mentioned in the figure are those for signing VU and external GNSS facility certificates. Section 9.1.3 denotes these as MSCA_VU-EGF.
 — The VU.CA.EUR certificate mentioned in the figure is the European root certificate that is indicated in the CAR of the VU.CA certificate.
 — The VU.Link certificate mentioned in the figure is the VU's link certificate, if present. As specified in section 9.1.2, this is a link certificate for a new European root key pair created by the ERCA and signed by the previous European private key.
 — The VU.Link.EUR certificate is the European root certificate that is indicated in the CAR of the VU.Link certificate.
 CSM_162  — the VU.CA.EUR certificate is the same certificate as the card's own EUR certificate;
 — the VU.CA.EUR certificate precedes the card's own EUR certificate and the card contained this certificate already at issuance (see CSM_91);
 — the VU.CA.EUR certificate succeeds the card's own EUR certificate and the card received a link certificate in the past from another vehicle unit, verified it and stored it for future reference.
 CSM_163 The VU shall use the MSE: Set AT command to set its public key for use in the tachograph card. As specified in Appendix 2, this command contains an indication of the cryptographic mechanism that will be used with the key that is set. This mechanism shall be ‘VU Authentication using the ECDSA algorithm, in combination with the hashing algorithm linked to the key size of the VU's VU_MA key pair, as specified in CSM_50’.
 CSM_164 The MSE: Set AT command also contains an indication of the ephemeral key pair which the VU will use during session key agreement (see section 10.4). Therefore, before sending the MSE: Set AT command, the VU shall generate an ephemeral ECC key pair. For generating the ephemeral key pair, the VU shall use the standardized domain parameters indicated in the card certificate. The ephemeral key pair is denoted as (VU.SKeph, VU.PKeph, Card.DP). The VU shall take the x-coordinate of the ECDH ephemeral public point as the key identification; this is called the compressed representation of the public key and denoted as Comp(VU.PKeph).
 CSM_165 If the MSE: Set AT command is successful, the card shall set the indicated VU.PK for subsequent use during Vehicle Authentication, and shall temporarily store Comp(VU.PKeph). In case two or more successful MSE: Set AT commands are sent before session key agreement is performed, the card shall store only the last Comp(VU.PKeph) received. The card shall reset Comp(VU.PKeph) after a successful GENERAL AUTHENTICATE command.
 CSM_166 The card shall verify the temporal validity of any certificate presented by the VU or referenced by the VU while stored in the card's memory, and shall reject expired certificates.
 CSM_167 

— Second-generation ERCA link certificates
— Second-generation MSCA certificates
— Second-generation VU certificates issued by the same country as the card's own card certificate(s).
Note: the last requirement implies that a card shall be able to recognize the CAR of the VU certificate, i.e. the MSCA_VU-EGF certificate. This will not be the same as the CAR of its own certificate, which is the MSCA_Card certificate. CSM_168 As indicated in Figure 5, once the card has verified the authenticity and validity of a previously unknown certificate, it may store this certificate for future reference, such that it does not need to verify that certificate's authenticity again if it is presented to the card again. Instead xof storing the entire certificate, a card may choose to store only the contents of the Certificate Body, as specified in section 9.3.2.
 10.3.  CSM_169 Vehicle units and cards shall use the VU Authentication protocol depicted in Figure 6 to authenticate the VU towards the card. VU Authentication enables the tachograph card to explicitly verify that the VU is authentic. To do so, the VU shall use its private key to sign a challenge generated by the card.
 CSM_170 Note: This ensures that the card to which the VU authenticates itself is the same card whose certificate chain the VU has verified previously. CSM_171 Note: This ensures that the VU with which a card communicates during a Secure Messaging session is the same VU that was authenticated by the card. Figure 6
                                     

 CSM_172 If multiple GET CHALLENGE commands are sent by the VU during VU Authentication, the card shall return a new 8-byte random challenge each time, but shall store only the last challenge.
 CSM_173 The signing algorithm used by the VU for VU Authentication shall be ECDSA as specified in [DSS], using the hashing algorithm linked to the key size of the VU's VU_MA key pair, as specified in CSM_50. The signature format shall be plain, as specified in [TR-03111]. The VU shall send the resulting signature to the card.
 CSM_174 

— Calculate the authentication token by concatenating Card.CHR, the card challenge rcard and the identifier of the VU ephemeral public key Comp(VU.PKeph),
— Verify the VU’s signature using the ECDSA algorithm, using the hashing algorithm linked to the key size of the VU’s VU_MA key pair as specified in CSM_50, in combination with VU.PK and the calculated authentication token.
 10.4.  CSM_175 Vehicle units and cards shall use the Chip Authentication protocol depicted in Figure 7 to authenticate the card towards the VU. Chip Authentication enables the vehicle unit to explicitly verify that the card is authentic.

Figure 7 CSM_176 

1.. The vehicle unit initiates the Chip Authentication process by sending the MSE: Set AT command indicating ‘Chip Authentication using the ECDH algorithm resulting in an AES session key length linked to the key size of the card's Card_MA key pair, as specified in CSM_50’. The VU shall determine the key size of the card's key pair from the card certificate.
2.. The VU sends the public point VU.PK
                                                   eph
                                                 of its ephemeral key pair to the card. The public point shall be converted to an octet string as specified in [TR-03111]. The uncompressed encoding format shall be used. As explained in CSM_164, the VU generated this ephemeral key pair prior to the verification of the VU certificate chain. The VU sent the identifier of the ephemeral public key Comp(VU.PK
                                                   eph
                                                ) to the card, and the card stored it.
3.. The card computes Comp(VU.PKeph) from VU.PKeph and compares this to the stored value of Comp(VU.PKeph).
4.. Using the ECDH algorithm in combination with the card's static private key and the VU's ephemeral public key, the card computes a secret K.
5.. The card chooses a random 8-byte nonce NPICC and uses it to derive two AES session keys KMAC and KENC from K. See CSM_179.
6.. Using K
                                                   MAC
                                                , the card computes an authentication token over the VU ephemeral public point: T
                                                   PICC
                                                 = CMAC(K
                                                   MAC
                                                , VU.PK
                                                   eph
                                                ). The public point shall be in the format used by the VU (see bullet 2 above). The card sends N
                                                   PICC
                                                 and T
                                                   PICC
                                                 to the vehicle unit.
7.. Using the ECDH algorithm in combination with the card's static public key and the VU's ephemeral private key, the VU computes the same secret K as the card did in step 4.
8.. The VU derives session keys KMAC and KENC from K and NPICC; see CSM_179.
9.. The VU verifies the authentication token TPICC.
 CSM_177 In step 3 above, the card shall compute Comp(VU.PKeph) as the x-coordinate of the public point in VU.PKeph.
 CSM_178 In steps 4 and 7 above, the card and the vehicle unit shall use the ECKA-EG algorithm as defined in [TR-03111].
 CSM_179 

— The value of the counter shall be ‘00 00 00 01’ for KENC and ‘00 00 00 02’ for KMAC.
— The optional nonce r shall be used and shall be equal to NPICC.
— For deriving 128-bits AES keys, the hashing algorithm to be used shall be SHA-256.
— For deriving 192-bits AES keys, the hashing algorithm to be used shall be SHA-384.
— For deriving 256-bits AES keys, the hashing algorithm to be used shall be SHA-512.

The length of the session keys (i.e. the length at which the hash is truncated) shall be linked to the size of the Card_MA key pair, as specified in CSM_50.
 CSM_180 In steps 6 and 9 above, the card and the vehicle unit shall use the AES algorithm in CMAC mode, as specified in [SP 800-38B]. The length of TPICC shall be linked to the length of the AES session keys, as specified in CSM_50.
 10.5.  10.5.1  CSM_181 All commands and responses exchanged between a vehicle unit and a tachograph card after successful Chip Authentication took place and until the end of the session shall be protected by Secure Messaging.
 CSM_182 Except when reading from a file with access condition SM-R-ENC-MAC-G2 (see Appendix 2, section 4), Secure Messaging shall be used in authentication-only mode. In this mode, a cryptographic checksum (a.k.a. MAC) is added to all commands and responses to ensure message authenticity and integrity.
 CSM_183 When reading data from a file with access condition SM-R-ENC-MAC-G2, Secure Messaging shall be used in encrypt-then-authenticate mode, i.e. the response data is encrypted first to ensure message confidentiality, and afterwards a MAC over the formatted encrypted data is calculated to ensure authenticity and integrity.
 CSM_184 Secure Messaging shall use AES as defined in [AES] with the session keys KMAC and KENC that were agreed during Chip Authentication.
 CSM_185 An unsigned integer shall be used as the Send Sequence Counter (SSC) to prevent replay attacks. The size of the SSC shall be equal to the AES block size, i.e. 128 bits. The SSC shall be in MSB-first format. The Send Sequence Counter shall be initialized to zero (i.e. ‘00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00’) when Secure Messaging is started. The SSC shall be increased every time before a command or response APDU is generated, i.e. since the starting value of the SSC in a SM session is 0, in the first command the value of the SSC will be 1. The value of SSC for the first response will be 2.
 CSM_186 For message encryption, KENC shall be used with AES in the Cipher Block Chaining (CBC) mode of operation, as defined in [ISO 10116], with an interleave parameter m = 1 and an initialization vector SV = E(KENC, SSC), i.e. the current value of the Send Sequence Counter encrypted with KENC.
 CSM_187 For message authentication, KMAC shall be used with AES in CMAC mode as specified in [SP 800-38B]. The length of the MAC shall be linked to the length of the AES session keys, as specified in CSM_50. The Send Sequence Counter shall be included in the MAC by prepending it before the datagram to be authenticated.
 10.5.2  CSM_188 

Table 5
Secure Messaging Data Objects
Data Object Name Tag Presence (M)andatory, (C)onditional or (F)orbidden in
Commands Responses
Plain value not encoded in BER-TLV ‘81’ C C
Plain value encoded in BER-TLV, but not including SM DOs ‘B3’ C C
Padding-content indicator followed by cryptogram, plain value not encoded in BER-TLV ‘87’ C C
Protected Le ‘97’ C F
Processing Status ‘99’ F M
Cryptographic Checksum ‘8E’ M MNote: As specified in Appendix 2, tachograph cards may support the READ BINARY and UPDATE BINARY command with an odd INS byte (‘B1’ resp. ‘D7’). These command variants are required to read and update files with more than 32 768 bytes or more. In case such a variant is used, a data object with tag ‘B3’ shall be used instead of an object with tag ‘81’. See Appendix 2 for more information. CSM_189 
TagThe tag is encoded in one or two octets and indicates the content.LengthThe length is encoded as an unsigned integer in one, two, or three octets, resulting in a maximum length of 65 535 octets. The minimum number of octets shall be used.ValueThe value is encoded in zero or more octets
 CSM_190 

— The command header shall be included in the MAC calculation, therefore value ‘0C’shall be used for the class byte CLA.
— As specified in Appendix 2, all INS bytes shall be even, with the possible exception of odd INS bytes for the READ BINARY and UPDATE BINARY commands.
— The actual value of Lc will be modified to Lc' after application of secure messaging.
— The Data field shall consist of SM data objects.
— In the protected command APDU the new Le byte shall be set to ‘00’. If required, a data object ‘97’ shall be included in the Data field in order to convey the original value of Le.
 CSM_191 
                                                Note:
                                              Padding for Secure Messaging is always performed by the secure messaging layer, not by the CMAC or CBC algorithms.
A command APDU with applied Secure Messaging will have the following structure, depending on the case of the respective unsecured command (DO is data object):


                                                Case 1
                                             CLA INS P1 P2 || Lc' || DO ‘8E’ || Le
                                                Case 2
                                             CLA INS P1 P2 || Lc' || DO ‘97’ || DO‘8E’ || Le
                                                Case 3 (even INS byte)
                                             CLA INS P1 P2 || Lc' || DO ‘81’ || DO‘8E’ || Le
                                                Case 3 (odd INS byte)
                                             CLA INS P1 P2 || Lc' || DO ‘B3’ || DO‘8E’ || Le
                                                Case 4 (even INS byte)
                                             CLA INS P1 P2 || Lc' || DO ‘81’ || DO‘97’ || DO‘8E’ || Le
                                                Case 4 (odd INS byte)
                                             CLA INS P1 P2 || Lc' || DO ‘B3’ || DO‘97’ || DO‘8E’ || Le

where Le = ‘00’ or ‘00 00’ depending on whether short length fields or extended length fields are used; see [ISO 7816-4].

A response APDU with applied Secure Messaging will have the following structure, depending on the case of the respective unsecured response:


                                                Case 1 or 3
                                             DO ‘99’ || DO ‘8E’ || SW1SW2
                                                Case 2 or 4 (even INS byte) without encryption
                                             DO ‘81’ || DO ‘99’ || DO ‘8E’ || SW1SW2
                                                Case 2 or 4 (even INS byte) with encryption
                                             DO ‘87’ || DO ‘99’ || DO ‘8E’ || SW1SW2
                                                Case 2 or 4 (odd INS byte) without encryption
                                             DO ‘B3’ || DO ‘99’ || DO ‘8E’ || SW1SW2

                                                Note:
                                              Case 2 or 4 (odd INS byte) with encryption is never used in the communication between a VU and a card.
Below are three example APDU transformations for commands with even INS code. Figure 8 shows an authenticated Case 4 command APDU, Figure 9 shows an authenticated Case 1/Case 3 response APDU, and Figure 10 shows an encrypted and authenticated Case 2/Case 4 response APDU.


                                             Figure 8
                                          

                                             Figure 9
                                           
                                             Figure 10
                                           

 10.5.3  CSM_192 

— it receives a plain response APDU,
— it detects a Secure Messaging error in a response APDU:
— An expected Secure Messaging data object is missing, the order of data objects is incorrect, or an unknown data object is included.
— A Secure Messaging data object is incorrect, e.g. the MAC value is incorrect, the TLV structure is incorrect or the padding indicator in tag ‘87’ is not equal to ‘01’.
— the card sends a status byte indicating it detected an SM error (see CSM_194),
— the limit for the number of commands and associated responses within the current session is reached. For a given VU, this limit shall be defined by its manufacturer, taking into account the security requirements of the hardware used, with a maximum value of 240 SM commands and associated responses per session.
 CSM_193 

— it receives a plain command APDU,
— it detects a Secure Messaging error in a command APDU:
— An expected Secure Messaging data object is missing, the order of data objects is incorrect, or an unknown data object is included.
— A Secure Messaging data object is incorrect, e.g. the MAC value is incorrect or the TLV structure is incorrect.
— it is depowered or reset,
— the VU starts the VU Authentication process,
— the limit for the number of commands and associated responses within the current session is reached. For a given card, this limit shall be defined by its manufacturer, taking into account the security requirements of the hardware used, with a maximum value of 240 SM commands and associated responses per session.
 CSM_194 

— If in a command APDU some expected Secure Messaging data objects are missing, the order of data objects is incorrect or unknown data objects are included, a tachograph card shall respond with status bytes ‘69 87’.
— If a Secure Messaging data object in a command APDU is incorrect, a tachograph card shall respond with status bytes ‘69 88’.

In such a case, the status bytes shall be returned without using SM.
 CSM_195 

— securely destroy the stored session keys
— immediately establish a new Secure Messaging session, as described in sections 10.2 — 10.5.
 CSM_196 If for any reason the VU decides to restart mutual authentication towards an inserted card, the process shall restart with verification of the card certificate chain, as described in section 10.2, and shall continue as described in sections 10.2 — 10.5.
 11.  11.1.  CSM_197 The GNSS facility used by a VU to determine its position may be internal, (i.e. built into the VU casing and not detachable), or it may be an external module. In the first case, there is no need to standardize the internal communication between the GNSS facility and the VU, and the requirements in this chapter do not apply. In the latter case, communication between the VU and the external GNSS facility shall be standardized and protected as described in this chapter.
 CSM_198 Secure communication between a vehicle unit and an external GNSS facility shall take place in the same way as secure communication between a vehicle unit and a tachograph card, with the external GNSS facility (EGF) taking the role of the card. All requirements mentioned in chapter 10 for tachograph cards shall be satisfied by an EGF, taking into account the deviations, clarifications and additions mentioned in this chapter. In particular, mutual certificate chain verification, VU Authentication and Chip Authentication shall be performed as described in sections 11.3 and 11.4.
 CSM_199 Communication between a vehicle unit and an EGF differs from communication between a vehicle unit and a card in the fact that a vehicle unit and an EGF must be coupled once in a workshop before the VU and the EGF can exchange GNSS-based data during normal operation. The coupling process is described in section 11.2.
 CSM_200 For communication between a vehicle unit and an EGF, APDU commands and responses based on [ISO 7816-4] and [ISO 7816-8] shall be used. The exact structure of these APDUs is defined in Appendix 2 of this Annex.
 11.2.  CSM_201 A vehicle unit and an EGF in a vehicle shall be coupled by a workshop. Only a coupled vehicle unit and EGF shall be able to communicate during normal operation.
 CSM_202 Coupling of a vehicle unit and an EGF shall only be possible if the vehicle unit is in calibration mode. The coupling shall be initiated by the vehicle unit.
 CSM_203 A workshop may re-couple a vehicle unit to another EGF or to the same EGF at any time. During re-coupling, the VU shall securely destroy the existing EGF_MA certificate in its memory and shall store the EGF_MA certificate of the EGF to which it is being coupled.
 CSM_204 A workshop may re-couple an external GNSS facility to another VU or to the same VU at any time. During re-coupling, the EGF shall securely destroy the existing VU_MA certificate in its memory and shall store the VU_MA certificate of the VU to which it is being coupled.
 11.3.  11.3.1  CSM_205 Mutual certificate chain verification between a VU and an EGF shall take place only during the coupling of the VU and the EGF by a workshop. During normal operation of a coupled VU and EGF, no certificates shall be verified. Instead, the VU and EGF shall trust the certificates they stored during the coupling, after checking the temporal validity of these certificates. The VU and the EGF shall not trust any other certificates for protecting the VU — EGF communication during normal operation.
 11.3.2  CSM_206  — Communication control is out of the scope of this Appendix. However, an EGF is not a smart card and hence the VU will probably not send a Reset to initiate the communication and will not receive an ATR.
 — The Card certificates and public keys mentioned in the figure shall be interpreted as the EGF's certificates and public keys for mutual authentication. Section 9.1.6 denotes these as EGF_MA.
 — The Card.CA certificates and public keys mentioned in the figure shall be interpreted as the MSCA's certificates and public keys for signing EGF certificates. Section 9.1.3 denotes these as MSCA_VU-EGF.
 — The Card.CA.EUR certificate mentioned in the figure shall be interpreted as the European root certificate that is indicated in the CAR of the MSCA_VU-EGF certificate.
 — The Card.Link certificate mentioned in the figure shall be interpreted as the EGF's link certificate, if present. As specified in section 9.1.2, this is a link certificate for a new European root key pair created by the ERCA and signed by the previous European private key.
 — The Card.Link.EUR certificate is the European root certificate that is indicated in the CAR of the Card.Link certificate.
 — Instead of the , the VU shall read the  from EF ICC.
 — Instead of selecting the Tachograph AID, the VU shall select the EGF AID.
 — ‘Ignore Card’ shall be interpreted as ‘Ignore EGF’.
 CSM_207 Once it has verified the EGF_MA certificate, the vehicle unit shall store this certificate for use during normal operation; see section 11.3.3.
 CSM_208  — The VU shall generate a fresh ephemeral key pair using the domain parameters in the EGF certificate.
 — The VU certificates and public keys mentioned in the figure are those for mutual authentication. Section 9.1.4 denotes these as VU_MA.
 — The VU.CA certificates and public keys mentioned in the figure are those for signing VU and external GNSS facility certificates. Section 9.1.3 denotes these as MSCA_VU-EGF.
 — The VU.CA.EUR certificate mentioned in the figure is the European root certificate that is indicated in the CAR of the VU.CA certificate.
 — The VU.Link certificate mentioned in the figure is the VU's link certificate, if present. As specified in section 9.1.2, this is a link certificate for a new European root key pair created by the ERCA and signed by the previous European private key.
 — The VU.Link.EUR certificate is the European root certificate that is indicated in the CAR of the VU.Link certificate.
 CSM_209 In deviation from requirement CSM_167, an EGF shall use the GNSS time to verify the temporal validity of any certificate presented.
 CSM_210 Once it has verified the VU_MA certificate, the external GNSS facility shall store this certificate for use during normal operation; see section 11.3.3.
 11.3.3  CSM_211 Note that Figure 11 in essence consists of the first steps shown in Figure 4 and Figure 5. Again, note that since an EGF is not a smart card, the VU will probably not send a Reset to initiate the communication and will not receive an ATR. In any case this is out of the scope of this Appendix.
Figure 11 CSM_212 As shown in Figure 11, the vehicle unit shall log an error if the EGF_MA certificate is no longer valid. However, mutual authentication, key agreement and subsequent communication via secure messaging shall proceed normally.
 11.4.  CSM_213 VU Authentication, Chip Authentication and session key agreement between a VU and an EGF shall take place during coupling and whenever a Secure Messaging session is re-established during normal operation. The VU and the EGF shall carry out the processes described in sections 10.3 and 10.4. All requirements in these sections shall apply.
 11.5.  CSM_214 All commands and responses exchanged between a vehicle unit and an external GNSS facility after successful Chip Authentication took place and until the end of the session shall be protected by Secure Messaging.in authentication-only mode. All requirements in section 10.5 shall apply.
 CSM_215 If a Secure Messaging session between a VU and an EGF is aborted, the VU shall immediately establish a new Secure Messaging session, as described in section 11.3.3 and 11.4.
 12.  12.1.  CSM_216 Note: readers of this chapter are supposed to be familiar with the contents of [ISO 16844-3]. 12.2. 
As explained in section 9.2.1, the motion sensor master key and all associated keys are regularly replaced. This leads to the presence of up to three motion sensor-related AES keys KM-WC (of consecutive key generations) in workshop cards. Similarly, in motion sensors up to three different AES-based encryptions of data (based on consecutive generations of the motion sensor master key KM) may be present. A vehicle unit contains only one motion sensor-related key KM-VU.
 CSM_217 

1.. A second-generation workshop card is inserted into the VU and the VU is connected to the motion sensor.
2.. The VU reads all available KM-WC keys from the workshop card, inspects their key version numbers and chooses the one matching the version number of the VU's KM-VU key. If the matching KM-WC key is not present on the workshop card, the VU aborts the pairing process and shows an appropriate error message to the workshop card holder.
3.. The VU calculates the motion sensor master key KM from KM-VU and KM-WC, and the identification key KID from KM, as specified in section 9.2.1.
4.. The VU sends the instruction to initiate the pairing process towards the motion sensor, as described in [ISO 16844-3], and encrypts the serial number it receives from the motion sensor with the identification key KID. The VU sends the encrypted serial number back to the motion sensor.
5.. The motion sensor matches the encrypted serial number consecutively with each of the encryptions of the serial number it holds internally. If it finds a match, the VU is authenticated. The motion sensor notes the generation of KID used by the VU and returns the matching encrypted version of its pairing key; i.e. the encryption that was created using the same generation of KM.
6.. The VU decrypts the pairing key using KM, generates a session key KS, encrypts it with the pairing key and sends the result to the motion sensor. The motion sensor decrypts KS.
7.. The VU assembles the pairing information as defined in [ISO 16844-3], encrypts the information with the pairing key, and sends the result to the motion sensor. The motion sensor decrypts the pairing information.
8.. The motion sensor encrypts the received pairing information with the received KS and returns this to the VU. The VU verifies that the pairing information is the same information which the VU sent to the motion sensor in the previous step. If it is, this proves that the motion sensor used the same KS as the VU and hence in step 5 sent its pairing key encrypted with the correct generation of KM. Hence, the motion sensor is authenticated.
Note that steps 2 and 5 are different from the standard process in [ISO 16844-3]; the other steps are standard.
Example: Suppose a pairing takes place in the first year of the validity of the ERCA (3) certificate; see Figure 2 in section 9.2.1.2. Moreover


— Suppose the motion sensor was issued in the last year of the validity of the ERCA (1) certificate. It will therefore contain the following keys and data:
— Ns[1]: its serial number encrypted with generation 1 of KID,
— Ns[2]: its serial number encrypted with generation 2 of KID,
— Ns[3]: its serial number encrypted with generation 3 of KID,
— KP[1]: its generation-1 pairing key, encrypted with generation 1 of KM,
— KP[2]: its generation-2 pairing key, encrypted with generation 2 of KM,
— KP[3]: its generation-3 pairing key, encrypted with generation 3 of KM,
— Suppose that the workshop card was issued in the first year of the validity of the ERCA (3) certificate. It will therefore contain the generation 2 and generation 3 of the KM-WC key.
— Suppose the VU is a generation-2 VU, containing the generation 2 of KM-VU.

In this case, the following will happen in steps 2 — 5:


— Step 2: The VU reads generation 2 and generation 3 of KM-WC from the workshop card and inspects their version numbers.
— Step 3: The VU combines the generation-2 KM-WC with its KM-VU to compute KM and KID.
— Step 4: The VU encrypts the serial number it receives from the motion sensor with KID.
— Step 5: The motion sensor compares the received data with Ns[1] and doesn't find a match. Next, it compares the data with Ns[2] and finds a match. It concludes that the VU is a generation-2 VU, and therefore sends back KP[2].
 12.3.  CSM_218 

Table 6
                                                

                                                   Number of plaintext and encrypted data bytes per instruction defined in [ISO 16844-3]
                                                

                                                Instruction
                                              
                                                Request / reply
                                              
                                                Description of data
                                              
                                                # of plaintext data bytes according to
                                                [ISO 16844-3]
                                              
                                                # of plaintext data bytes using AES keys
                                              
                                                # of encrypted data bytes when using AES keys of bitlength
                                             

                                                128
                                              
                                                192
                                              
                                                256
                                             

                                                10
                                              
                                                request
                                              
                                                Authentication data + file number
                                              
                                                8
                                              
                                                8
                                              
                                                16
                                              
                                                16
                                              
                                                16
                                             

                                                11
                                              
                                                reply
                                              
                                                Authentication data + file contents
                                              
                                                16 or 32, depend on file
                                              
                                                16 or32, depend on file
                                              
                                                32 / 48
                                              
                                                32 / 48
                                              
                                                32 / 48
                                             

                                                41
                                              
                                                request
                                              
                                                MoS serial number
                                              
                                                8
                                              
                                                8
                                              
                                                16
                                              
                                                16
                                              
                                                16
                                             

                                                41
                                              
                                                reply
                                              
                                                Pairing key
                                              
                                                16
                                              
                                                16 / 24 / 32
                                              
                                                16
                                              
                                                32
                                              
                                                32
                                             

                                                42
                                              
                                                request
                                              
                                                Session key
                                              
                                                16
                                              
                                                16 / 24 / 32
                                              
                                                16
                                              
                                                32
                                              
                                                32
                                             

                                                43
                                              
                                                request
                                              
                                                Pairing information
                                              
                                                24
                                              
                                                24
                                              
                                                32
                                              
                                                32
                                              
                                                32
                                             

                                                50
                                              
                                                reply
                                              
                                                Pairing information
                                              
                                                24
                                              
                                                24
                                              
                                                32
                                              
                                                32
                                              
                                                32
                                             

                                                70
                                              
                                                request
                                              
                                                Authentication data
                                              
                                                8
                                              
                                                8
                                              
                                                16
                                              
                                                16
                                              
                                                16
                                             

                                                80
                                              
                                                reply
                                              
                                                MoS counter value + auth. data
                                              
                                                8
                                              
                                                8
                                              
                                                16
                                              
                                                16
                                              
                                                16 CSM_219 

— In case the pairing key KP is 16 bytes long: K'p = KP XOR (Ns||Ns)
— In case the pairing key KP is 24 bytes long: K'p = KP XOR (Ns||Ns||Ns)
— In case the pairing key KP is 32 bytes long: K'p = KP XOR (Ns||Ns||Ns||Ns)

where Ns is the 8-byte serial number of the motion sensor.
 CSM_220 Note: in [ISO 16844-3], the number of plaintext data bytes is always a multiple of 8, such that padding is not necessary when using TDES. The definition of data and messages in [ISO 16844-3] is not changed by this part of this Appendix, thus necessitating the application of padding. CSM_221 

— For instruction 11: the 8-byte authentication block specified in section 7.6.3.3 of [ISO 16844-3], padded using padding method 2 defined in [ISO 9797-1]; see also section 7.6.5 and 7.6.6 of [ISO 16844-3].
— For all other instructions in which more than 16 bytes are transferred, as specified in Table 6: ‘00’ {16}, i.e. sixteen bytes with binary value 0.
Note: As shown in section 7.6.5 and 7.6.6 of [ISO 16844-3], when the MoS encrypts data files for inclusion in instruction 11, the authentication block is both
— Used as the initialization vector for the CBC-mode encryption of the data files
— Encrypted and included as the first block in the data that is sent to the VU. 12.4.  CSM_222  — It is not possible to pair a second-generation VU to a first-generation motion sensor.
 — It is not possible to use a first-generation workshop card for coupling a second-generation VU to a motion sensor.
 13.  13.1. 
As specified in Appendix 14, a VU regularly generates Remote Tachograph Monitoring (RTM) data and sends this data to the (internal or external) Remote Communication Facility (RCF). The remote communication facility is responsible for sending this data over the DSRC interface described in Appendix 14 to the remote interrogator. Appendix 1 specifies that the RTM data is the concatenation of:

Encrypted tachograph payloadthe encryption of the plaintext tachograph payloadDSRC security datadescribed below

The plaintext tachograph payload data format is specified in Appendix 1 and further described in Appendix 14. This section describes the structure of the DSRC security data; the formal specification is in Appendix 1.
 CSM_223 The plaintext  data communicated by a VU to a Remote Communication Facility (if the RCF is external to the VU) or from the VU to a remote interrogator over the DSRC interface (if the RCF is internal in the VU) shall be protected in encrypt-then-authenticate mode, i.e. the tachograph payload data is encrypted first to ensure message confidentiality, and afterwards a MAC is calculated to ensure data authenticity and integrity.
 CSM_224 
Current date timethe current date and time of the VU (data type )Countera 3-byte counter, see CSM_225VU serial number
                                             the VU’s serial number or certificate request ID (data type VuSerialNumber or CertificateRequestID) – see CSM_123DSRC master key version numberthe 1-byte version number of the DSRC master key from which the VU-specific DSRC keys were derived, see section 9.2.2.MACthe MAC calculated over all previous bytes in the RTM data.
 CSM_225 The 3-byte counter in the DSRC security data shall be in MSB-first format. The first time a VU calculates a set of RTM data after it is taken into production, it shall set the value of the counter to 0. The VU shall increase the value of the counter data by 1, each time before it calculates a next set of RTM data.
 13.2.  CSM_226 Given a plaintext data element with data type  as described in Appendix 14, a VU shall encrypt this data as shown in Figure 12: the VU's DSRC key for encryption K_VUDSRC_ENC (see section 9.2.2) shall be used with AES in the Cipher Block Chaining (CBC) mode of operation, as defined in [ISO 10116], with an interleave parameter m = 1. The initialization vector shall be equal to IV = current date time || ‘00 00 00 00 00 00 00 00 00’ || counter, where current date time and counter are specified in CSM_224. The data to be encrypted shall be padded using method 2 defined in [ISO 9797-1].
 CSM_227 A VU shall calculate the MAC in the DSRC security data as shown in Figure 12: the MAC shall be calculated over all preceding bytes in the RTM data, up to and including the DSRC master key version number, and including the tags and lengths of the data objects. The VU shall use its DSRC key for authenticity K_VUDSRC_MAC (see section 9.2.2) with the AES algorithm in CMAC mode as specified in [SP 800-38B]. The length of the MAC shall be linked to the length of the VU-specific DSRC keys, as specified in CSM_50.

Figure 12 13.3.  CSM_228 

1.. The control card shall inspect the DSRC master key version number in the DSRC security data. If the control card does not know the indicated DSRC master key, it shall return an error specified in Appendix 2 and abort the process.
2.. The control card shall use the indicated DSRC master key in combination with the VU serial number or the certificate request ID in the DSRC security data to derive the VU-specific DSRC keys K_VU
                                                   DSRC
                                                _ENC and K_VU
                                                   DSRC
                                                _MAC, as specified in CSM_124.
3.. The control card shall use K_VUDSRC_MAC to verify the MAC in the DSRC security data, as specified in CSM_227. If the MAC is incorrect, the control card shall return an error specified in Appendix 2 and abort the process.
4.. The control card shall use K_VUDSRC_ENC to decrypt the encrypted tachograph payload, as specified in CSM_226. The control card shall remove the padding and shall return the decrypted tachograph payload data to the remote interrogator.
 CSM_229  — This requires the remote interrogator to have an accurate and reliable source of time.
 — Since Appendix 14 requires a VU to calculate a new set of RTM data every 60 seconds, and the clock of the VU is allowed to deviate 1 minute from the real time, a lower limit for the freshness of the RTM data is 2 minutes. The actual freshness to be required also depends on the accuracy of the clock of the remote interrogator.
 CSM_230 When a workshop verifies the correct functioning of the DSRC functionality of a VU, it shall send the entire RTM data received from the VU to a workshop card in the data field of a PROCESS DSRC MESSAGE command, as described in Appendix 2. The workshop card shall perform all checks and actions specified in CSM_228.
 14.  14.1.  CSM_231 

— In case of a VU download:
— The VU_Sign certificate
— The MSCA_VU-EGF certificate containing the public key to be used for verification of the VU_Sign certificate
— In case of a Card download:
— The Card_Sign certificate
— The MSCA_Card certificate containing the public key to be used for verification of the Card_Sign certificate
 CSM_232 

— In case it uses a control card to verify the signature, as shown in Figure 13: The link certificate linking the latest EUR certificate to the EUR certificate whose validity period directly precedes it, if existing.
— In case it verifies the signature itself: all valid European root certificates.
Note: the method the IDE uses to retrieve these certificates is not specified in this Appendix. 14.2.  CSM_233 The signing algorithm to create digital signatures over downloaded data shall be ECDSA as specified in [DSS], using the hashing algorithm linked to the key size of the VU or the card, as specified in CSM_50. The signature format shall be plain, as specified in [TR-03111].
 14.3.  CSM_234 

— Second-generation ERCA link certificates
— Second-generation MSCA certificates
— Second-generation VU_Sign or Card_Sign certificates issued by the same country as the control card’s own card certificate.

In case it performs signature verification itself, the IDE shall verify the authenticity and validity of all certificates in the certificate chain in the data file, and it shall verify the signature over the data following the signature scheme defined in [DSS]. In both cases, for every certificate read from the data file, it is necessary to verify that the Certificate Holder Authorisation (CHA) field is correct:


— The CHA field of the EQT certificate shall indicate a VU or Card (as applicable) certificate for signing (see Appendix 1, data type EquipmentType).
— The CHA of the EQT.CA certificate shall indicate an MSCA.
— The CHA of the EQT.Link certificate shall indicate the ERCA.
 — The equipment that signed the data to be analysed is denoted EQT.
 — The EQT certificates and public keys mentioned in the figure are those for signing, i.e. VU_Sign or Card_Sign.
 — The EQT.CA certificates and public keys mentioned in the figure are those for signing VU or Card certificates, as applicable.
 — The EQT.CA.EUR certificate mentioned in the figure is the European root certificate that is indicated in the CAR of the EQT.CA certificate.
 — The EQT.Link certificate mentioned in the figure is the EQT's link certificate, if present. As specified in section 9.1.2, this is a link certificate for a new European root key pair created by the ERCA and signed with the previous European private key.
 — The EQT.Link.EUR certificate is the European root certificate that is indicated in the CAR of the EQT.Link certificate.
 CSM_235 For calculating the hash M sent to the control card in the PSO:Hash command, the IDE shall use the hashing algorithm linked to the key size of the VU or the card from which the data is downloaded, as specified in CSM_50.
 CSM_236 Note: This document does not specify any action to undertake if a signature over a downloaded data file cannot be verified or if the verification is unsuccessful. Figure 13
                                     


Appendix 12 1. 
This Appendix provides the technical requirements for the GNSS data used by the Vehicle Unit, including the protocols that must be implemented to assure the secure and correct data transfer of the positioning information.

The main articles in this Regulation (EU) No 165/2014 driving these requirements are: ‘Article 8 Recording of the position of the vehicle at certain points during the daily working period’, ‘Article 10 Interface with Intelligent Transport Systems’ and ‘Article 11 Detailed provisions for smart tachographs’.
 1.1.  GNS_1 The Vehicle Unit shall collect location data from at least one GNSS to support the implementation of Article 8.

The Vehicle Unit may be with or without an external GNSS facility as described in Figure 1:

Figure 1 1.2. 
The following acronyms are used in this appendix:

DOPDilution of PrecisionEGFElementary file GNSS FacilityEGNOSEuropean Geostationary Navigation Overlay ServiceGNSSGlobal Navigation Satellite SystemGSAGPS DOP and active satellitesHDOPHorizontal Dilution of PrecisionICDInterface Control DocumentNMEANational Marine Electronics AssociationPDOPPosition Dilution of PrecisionRMCRecommended Minimum SpecificSISSignal in SpaceVDOPVertical Dilution of PrecisionVUVehicle Unit
 2. 
Regardless of the configuration of the Smart Tachograph with or without an external GNSS facility, the provision of accurate and reliable positioning information is an essential element of the effective operation of the Smart Tachograph. Therefore, it is appropriate to require its compatibility with the services provided by the Galileo and European Geostationary Navigation Overlay Service (EGNOS) programmes as set out in Regulation (EU) No 1285/2013 of the European Parliament and of the Council. The system established under the Galileo programme is an independent global satellite navigation system and the one established under the EGNOS programme is a regional satellite navigation system improving the quality of the Global Positioning System signal.
 GNS_2 Manufacturers shall ensure that the GNSS receivers in the Smart Tachographs are compatible with the positioning services provided by the Galileo and the EGNOS systems. Manufacturers may also choose, in addition, compatibility with other satellite navigation systems.
 GNS_3 The GNSS receiver shall have the capability to support Authentication on the Open Service of Galileo when such service will be provided by the Galileo system and supported by GNSS receiver manufacturers. However, for smart tachographs introduced in the market before the previous conditions are satisfied and not having the capability to support Authentication of the Open Service of Galileo, no retrofitting will be required.
 3. 
This section describes the NMEA sentences used in the functioning of the Smart Tachograph. This section is valid both for the configuration of the Smart Tachograph with or without an external GNSS facility.
 GNS_4 The location data is based on the NMEA sentence Recommended Minimum Specific (RMC) GNSS Data, which contains the Position information (Latitude, Longitude), Time in UTC format (hhmmss.ss), and Speed Over Ground in Knots plus additional values.

The format of the RMC sentence is the following (as from NMEA V4.1 standard):

Figure 2The Status gives indication if the GNSS signal is available. Until the value of the Status is not set to A, the received data (e.g., on Time or Latitude/Longitude) cannot be used to record the position of the vehicle in the VU.The resolution of the position is based on the format of the RMC sentence described above. The first part of the fields 3) and 5) are used to represent the degrees. The rest are used to represent the minutes with three decimals. So the resolution is 1/1000 of minute or 1/60000 of degree (because one minute is 1/60 of a degree). GNS_5 
The GPS DOP and active satellites (GSA) command can be used by the VU to determine and record the signal availability and accuracy. In particular the HDOP is used to provide an indication on the level of accuracy of the recorded location data (see 4.2.2). The VU will store the value of the Horizontal Dilution of Precision (HDOP) calculated as the minimum of the HDOP values collected on the available GNSS systems.

The GNSS Id. indicates the corresponding NMEA Id. for every GNSS constellation and Satellite-Based Augmentation System (SBAS).
 
                                    Figure 3
                                  

 GNS_6 The 
                                    GSA
                                  sentence shall be stored with record number ‘02’ to ‘06’.
 GNS_7 The maximum size of the NMEA sentences (e.g., RMC, GSA or others), which can be used for the sizing of the read record command shall be 85 bytes (see Table 1).
 4.  4.1.  4.1.1 
In this configuration, the GNSS receiver is a part of the external GNSS facility.
 GNS_8 The external GNSS facility must be powered with a specific vehicle interface.
 GNS_9 

((a)) A commercial GNSS receiver to provide the position data through the GNSS data interface. For example, the GNSS data interface can be NMEA standard V4.10 where The GNSS receiver acts as a talker and transmit NMEA sentences to the GNSS Secure Transceiver with a frequency of 1Hz for the pre-defined set of NMEA sentences, which must include at least the RMC and GSA sentences. The implementation of the GNSS data interface is a choice of the manufacturers of the external GNSS facility.
((b)) A transceiver unit (GNSS Secure Transceiver) with the capability to support standard ISO/IEC 7816-4:2013 (see 4.2.1) to communicate with the vehicle unit and support the GNSS data interface to the GNSS receiver. The unit is provided with a memory to store the identification data of the GNSS receiver and external GNSS facility.
((c)) An enclosure system with tamper detection function, which encapsulate both the GNSS receiver and the GNSS Secure Transceiver. The tamper detection function shall implement the security protection measures as requested in the Protection Profile of the Smart Tachograph.
((d)) A GNSS antenna installed on the vehicle and connected to the GNSS receiver through the enclosure system.
 GNS_10 

((a)) the interface to the GNSS antenna installed on the vehicle truck, if an external antenna is used.
((b)) the interface to the Vehicle Unit.
 GNS_11 In the VU, the VU Secure Transceiver is the other end of the secure communication with the GNSS Secure Transceiver and it must support ISO/IEC 7816-4:2013 for the connection to the external GNSS facility.
 GNS_12 For the physical layer of the communication with the external GNSS facility, the vehicule unit shall support ISO/IEC 7816-12:2005 or another standard able to support ISO/IEC 7816-4:2013. (see 4.2.1).
 4.1.2  GNS_13 

— the EGF_MA key pair and corresponding certificate,
— the MSCA_VU-EGF certificate containing the MSCA_VU-EGF.PK public key to be used for verification of the EGF_MA certificate,
— the EUR certificate containing the EUR.PK public key to be used for verification of the MSCA_VU-EGF certificate,
— the EUR certificate whose validity period directly precedes the validity period of the EUR certificate to be used to verify the MSCA_VU-EGF certificate, if existing,
— the link certificate linking these two EUR certificates, if existing,
— the extended serial-number of the external GNSS facility,
— operating system identifier of the GNSS facility,
— type approval number of the external GNSS facility;
— Identifier of the security component of the external GNSS module.
 4.2.  4.2.1  GNS_14 

1.. The collection and distribution of GNSS data (e.g., position, timing, speed),
2.. The collection of the configuration data of the external GNSS facility,
3.. The management protocol to support the coupling, mutual authentication and session key agreement between the external GNSS facility and the VU.
 GNS_15 The communication protocol shall be based on standard ISO/IEC 7816-4:2013 with the VU Secure Transceiver playing the master role and the GNSS Secure Transceiver playing the slave role. The physical connection between the external GNSS facility and the vehicule unit is based on ISO/IEC 7816-12:2005 or another standard able to support ISO/IEC 7816-4:2013
 GNS_16 In the communication protocol, extended length fields shall not be supported.
 GNS_17 The communication protocol of ISO 7816 (both *-4:2013 and *-12:2005) between the external GNSS facility and the VU shall be set to T = 1.
 GNS_18 Regarding the functions 1) the collection and distribution of GNSS data and 2) the collection of the configuration data of the external GNSS facility and 3) management protocol, the GNSS Secure Transceiver shall simulate a smart card with a file system architecture composed by a Master File (MF), a Dedicated File (DF) with Application Identifier specified in Appendix 1 chapter 6.2 (‘FF 44 54 45 47 4D’) and with 3 EFs containing certificates and one single Elementary File (EF.EGF) with file identifier equal to ‘2F2F’ as described in Table 1.
 GNS_19 The GNSS Secure Transceiver shall store the data coming from the GNSS receiver and the configuration in the EF.EGF. This is a linear, variable-length record file with an identifier equal to ‘2F2F’ in hexadecimal format.
 GNS_20 
The mapping of record numbers and data is provided in Table 1. Note that there are five GSA sentences for the GNSS constellations and Satellite-Based Augmentation System (SBAS).
 GNS_21 

Table 1
File Structure
  Access conditions
File File ID Read Update Encrypted
MF 3F00   
EF.ICC 0002 ALW NEV(by VU) No
DF GNSS Facility 0501 ALW NEV No
EF EGF_MACertificate C100 ALW NEV No
EF CA_Certificate C108 ALW NEV No
EF Link_Certificate C109 ALW NEV No
EF.EGF 2F2F SM-MAC NEV(by VU) No
File / Data element Record no Size (bytes) Default values
  Min Max 
MF  552 1 031 
EF.ICC    
sensorGNSSSerialNumber  8 8 
    
DF GNSS Facility  612 1 023 
EF EGF_MACertificate  204 341 
EGFCertificate  204 341 {00..00}
EF CA_Certificate  204 341 
MemberStateCertificate  204 341 {00..00}
EF Link_Certificate  204 341 
LinkCertificate  204 341 {00..00}
    
EF.EGF    
RMC NMEA Sentence ‘01’ 85 85 
1st GSA NMEA Sentence ‘02’ 85 85 
2nd GSA NMEA Sentence ‘03’ 85 85 
3rd GSA NMEA Sentence ‘04’ 85 85 
4th GSA NMEA Sentence ‘05’ 85 85 
5th GSA NMEA Sentence ‘06’ 85 85 
Extended serial-number of the external GNSS facility defined in Appendix 1 as SensorGNSSSerialNumber. ‘07’ 8 8 
Operating system identifier of the GNSS Secure Transceiver defined in Appendix 1 as SensorOSIdentifier. ‘08’ 2 2 
Type approval number of the external GNSS facility defined in Appendix 1 as SensorExternalGNSSApprovalNumber. ‘09’ 16 16 
Identifier of the security component of the external GNSS facility defined in Appendix 1 as SensorExternalGNSSSCIdentifier ‘10’ 8 8 
RFU — Reserved for Future Use From ‘11’ to ‘FD’    4.2.2  GNS_22 

1.. The coupling process has been completed as described in Appendix 11. Common security mechanisms.
2.. The periodic mutual authentication and session key agreement between the VU and the external GNSS facility also described in Appendix 11. Common security mechanisms has been executed with the indicated frequency.
 GNS_23 

1.. The VU requests location data from the External GNSS facility together with Dilution of Precision data (from the GSA NMEA sentence). The VU Secure Transceiver shall use the ISO/IEC 7816-4:2013 SELECT and READ RECORD(S) command in secure messaging authentication-only mode as described in Appendix 11 section 11.5 with the file identifier ‘2F2F’ and RECORD number equal to ‘01’ for RMC NMEA sentence and ‘02’,‘03’,‘04’,‘05’,‘06’ for GSA NMEA sentence.
2.. The last location data received is stored in the EF with identifier ‘2F2F’ and the records described in Table 1 in the GNSS secure transceiver as the GNSS secure transceiver receives NMEA data with a frequency of at least 1 Hz from the GNSS receiver through the GNSS data interface.
3.. The GNSS Secure Transceiver sends the response to the VU Secure Transceiver by using the APDU response message in secure messaging authentication-only mode as described in Appendix 11 section 11.5.
4.. The VU Secure Transceiver checks the authenticity and integrity of the received response. In case of positive outcome, the location data is transferred to the VU processor through the GNSS data interface.
5.. The VU processor checks the received data extracting the information (e.g., latitude, longitude, time) from the RMC NMEA sentence. The RMC NMEA sentence includes the information if the position is valid. If the position is not valid, the location data is not available yet and it cannot be used to record the position of the vehicle. If the position is valid, the VU processor also extracts the values of HDOP from GSA NMEA sentences and calculate the minimum value on the available satellite systems (i.e., when the fix is available).
6.. The VU processor stores the received and processed information such as latitude, longitude, time and speed in the VU in the format defined in Appendix 1 Data Dictionary as GeoCoordinates together with the value of HDOP calculated as the minimum of the HDOP values collected on the available GNSS systems.
 4.2.3 
This section describes in detail the structure of the Read Record command. Secure messaging (authentication-only mode) is added as described in Appendix 11 Common security mechanisms.
 GNS_24 The command shall support the Secure Messaging authentication-only-mode, see Appendix 11.
 GNS_25 
Byte Length Value Description
CLA 1 ‘0Ch’ Secure messaging asked.
INS 1 ‘B2h’ Read Record
P1 1 ‘XXh’ Record number (‘00’ references the current record)
P2 1 ‘04h’ Read the record with the record number indicated in P1
Le 1 ‘XXh’ Length of data expected. Number of Bytes to be read. GNS_26 
Byte Length Value Description
#1-#X X ‘XX..XXh’ Data read
SW 2 ‘XXXXh’ Status Words (SW1,SW2)

— If the command is successful, the GNSS secure transceiver returns ‘9000’.
— If the current file is not record oriented, the GNSS secure transceiver returns ‘6981’.
— If the command is used with P1 = ‘00’ but there is no current EF the GNSS secure transceiver returns ‘6986’ (command not allowed).
— If the record is not found, the GNSS secure transceiver returns ‘6A 83’.
— If the external GNSS facility has detected tampering, it shall return status words ‘66 90’.
 GNS_27 
Command Reference
Select Appendix 2 chapter 3.5.1
Read Binary Appendix 2 chapter 3.5.2
Get Challenge Appendix 2 chapter 3.5.4
PSO: Verify Certificate Appendix 2 chapter 3.5.7
External Authenticate Appendix 2 chapter 3.5.9
General Authenticate Appendix 2 chapter 3.5.10
MSE:SET Appendix 2 chapter 3.5.11 4.3. 
The coupling, mutual authentication and session key agreement of the external GNSS facility with the vehicle unit is described in Appendix 11. Common security mechanisms, Chapter 11.
 4.4. 
This section describes how potential error conditions by the external GNSS facility are addressed and recorded in the VU.
 4.4.1  GNS_28 If the VU does not manage to communicate to the coupled external GNSS facility for more than 20 continuous minutes, the VU shall generate and record in the VU an event of type EventFaultType with the value of enum ‘0E’H Communication error with the external GNSS facility and with the timestamp set to the current time. The event will be generated only if the following two conditions are satisfied: (a) the Smart Tachograph is not in calibration mode and (b) the vehicle is moving. In this context, a communication error is triggered when the VU Secure Transceiver does not receive a response message after a request message as described in 4.2.
 4.4.2  GNS_29 If the external GNSS facility has been breached, the GNSS Secure Transceiver shall erase all its memory including cryptographic material. As described in GNS_25 and GNS_26, the VU shall detect tampering if the Response has status ‘6690’. The VU shall then generate an event of type EventFaultType enum ‘19’H Tamper detection of GNSS. Alternately, the external GNSS facility may not respond to any external request anymore.
 4.4.3  GNS_30 If the GNSS Secure Transceiver does not receive data from the GNSS receiver for more than 3 continuous hours, the GNSS Secure Transceiver shall generate a response message to the READ RECORD command with RECORD number equal to ‘01’ with a Data Field of 12 bytes all set to 0xFF. Upon reception of the Response message with this value of the data field, the VU shall generate and record an event of type EventFaultType enum ‘0D’H Absence of position information from GNSS receiver event with a timestamp equal to the current value of time only if the following two conditions are satisfied: a) the Smart Tachograph is not in calibration mode and b) the vehicle is moving.
 4.4.4  GNS_31 If the VU detects that the EGF certificate used for mutual authentication is not valid any longer, the VU shall generate and record a recording equipment event of type EventFaultType enum ‘
                                          1B
                                          ’
                                          H External GNSS facility certificate expired
                                        with a timestamp equal to the current value of time. The VU shall still use the received GNSS position data.

Figure 4 5.  5.1. 
In this configuration, the GNSS receiver is inside the Vehicle Unit as described in Figure 1.
 GNS_32 The GNSS receiver shall act as a talker and transmit NMEA sentences to the VU processor, which shall act as a listener with a frequency of 1/10 Hz or faster for the pre-defined set of NMEA sentences, which shall include at least the RMC and GSA sentences.
 GNS_33 An external GNSS antenna installed on the vehicle or an internal GNSS antenna shall be connected to the VU.
 5.2.  5.2.1  GNS_34 If the VU does not receive data from the GNSS receiver for more than 3 continous hours, the VU shall generate and record an event of type EventFaultType enum ‘0D’H Absence of position information from GNSS receiver event with a timestamp equal to the current value of time only if the following two conditions are satisfied: (a) the Smart Tachograph is not in calibration mode and (b) the vehicle is moving.
 6. 
If the VU detects a discrepancy of more than 1 minute between the time of the vehicle unit's time measurement function and the time originating from the GNSS receiver, the VU will record an event of type EventFaultType enum ‘
                                 0B
                                 ’
                                 H Time conflict (GNSS versus VU internal clock)
                              . After a time conflict event has been triggered, the VU will not check the time discrepancy for the next 12 hours. This event shall not be triggered in cases no valid GNSS signal was detectable by the GNSS receiver within the last 30 days.
 7.  GNS_35 

— every 10 seconds maximum, the absolute value of the difference between the vehicle speed estimated from the GNSS and the one estimated from the motion sensor shall be computed.
— all the computed values in a time window containing the last five minutes of movement shall be used to compute the median value.
— the median value shall be computed as the average of 80 % of the remaining values, after having eliminated the highest ones in absolute values

The Vehicle Motion Conflict event shall be triggered if the median value is above 10 Km/h for five uninterrupted minutes of vehicle movement. Other independent sources of vehicle motion detection may optionnally be used, so that a more reliable detection of tachograph manipulations is provided. (Note: the use of the median on the last 5 minutes is applied to mitigate the risk of measurement outliers and transient values). This event shall not be triggered in the following conditions: (a) during a ferry/train crossing, (b) when the position information from the GNSS receiver shall not be available and (c) while in calibration mode.

Appendix 13 1. 
This Appendix specifies the design and the procedures to follow in order to implement the interface with Intelligent Transport Systems (ITS) as required in Article 10 of Regulation (EU) No. 165/2014 (the Regulation).

The Regulation specifies that the tachographs of vehicles may be equipped with standardised interfaces allowing the data recorded or produced by tachograph to be used in operational mode, by an external device, provided that the following conditions are met:


((a)) the interface does not affect the authenticity and the integrity of the data of the tachograph;
((b)) the interface complies with the detailed provisions of Article 11 of the Regulation;
((c)) the external device connected to the interface has access to personal data, including geopositioning data, only after the verifiable consent of the driver to whom the data relates.
 2. 
The scope of this Appendix is to specify how applications hosted on external devices can via a Bluetooth® connection obtain data (the Data) from a tachograph.

The Data available via this interface is described in the Annex 1 of the present document. This interface does not prohibit the implementation of other interfaces (e.g. via the CAN bus) to transmit the data of the VU to other vehicle processing units.

This Appendix specifies:


— The Data available through the ITS interface
— The Bluetooth® profile that is used to transfer the data
— The enquiry and download procedures and sequence of operations
— The pairing mechanism between the tachograph and the external device
— The consent mechanism available to the driver

For clarification, this Appendix does 
                                 not
                               specify:


— The collection of 
                                          the Data
                                        operation and management within the VU (which shall be specified elsewhere within 
                                          the Regulation
                                        or otherwise shall be a function of product design).
— The form of presentation of collected data to application hosted on the external device.
— Data security provisions above what provides Bluetooth® (such as encryption) concerning the content of 
                                          the Data
                                        (which shall be specified elsewhere within 
                                          the Regulation
                                        [Appendix 11 Common Security Mechanisms]).
— The Bluetooth® protocols used by the ITS interface
 2.1. 
The following acronyms and definitions specific to this Appendix are used in this appendix:

the Communicationexchange of information/data between a master unit (i.e. the tachographs) and an external unit through the ITS interface over Bluetooth®.the DataData sets as specified in Annex 1.the RegulationRegulation (EU) No 165/2014 of the European Parliament and of the Council of 4 February 2014 on tachographs in road transport, repealing Council Regulation (EEC) No 3821/85 on recording equipment in road transport and amending Regulation (EC) No 561/2006 of the European Parliament and of the Council on the harmonisation of certain social legislation relating to road transportBRBasic RateEDREnhanced Data RateGNSSGlobal Navigation Satellite SystemIRKIdentity Resolution KeyITSIntelligent Transport SystemLELow EnergyPINPersonal Identification NumberPUCPersonal Unblocking CodeSIDService IdentifierSPPSerial Port ProfileSSPSecure Simple PairingTRTPTransfer Request ParameterTREPTransfer Response ParameterVUVehicle Unit
 3. 
The specification defined in this Appendix refers to and depends upon all or parts of the following regulations and standards. Within the clauses of this Appendix the relevant standards, or relevant clauses of standards, are specified. In the event of any contradiction the clauses of this Appendix shall take precedence.

Regulations and standards referenced in this Appendix are:


— Regulation (EU) No 165/2014 of the European Parliament and of the Council of 4 February 2014 on tachographs in road transport, repealing Council Regulation (EEC) No 3821/85 on recording equipment in road transport and amending Regulation (EC) No 561/2006 of the European Parliament and of the Council on the harmonisation of certain social legislation relating to road transport.
— Regulation (EC) No 561/2006 of the European Parliament and of the Council of 15 March 2006 on the harmonisation of certain social legislation relating to road transport and amending Council Regulations (EEC) No 3821/85 and (EC) No 2135/98 and repealing Council Regulation (EEC) No 3820/85.
— ISO 16844 — 4: Road vehicles — Tachograph systems — Part 4: Can interface
— ISO 16844 — 7: Road vehicles — Tachograph systems — Part 7: Parameters
— Bluetooth® — Serial Port Profile — V1.2
— Bluetooth® — Core Version 4.2
— NMEA 0183 V4.1 protocol
 4.  4.1. 
The VU shall be responsible to keep updated and maintain the data to be stored in the VU, without any involvement of the ITS interface. The means by which this is achieved is internal to the VU, specified elsewhere in the Regulation, and is not specified in this Appendix.
 4.1.1 
The VU shall be responsible to update the data that will be available through the ITS interface at a frequency determined within VU procedures, without any involvement of ITS interface. The VU data shall be used as a basis to populate and update the Data, the means by which this is achieved is specified elsewhere in the Regulation or if there is no such specification is a function of product design and is not specified in this Appendix.
 4.1.2 
The content of the Data shall be as specified in Annex 1 of this appendix.
 4.1.3 
ITS applications will be using the data made available through the ITS interface for instance to optimize driver activities management while respecting the Regulation, to detect possible faults of the tachograph or to use the GNSS data. The specification of the applications is not within the scope of this Appendix.
 4.2. 
The Data exchange using the ITS interface shall be performed via a Bluetooth® interface compatible via version 4.2 or later. Bluetooth® operates in the unlicensed industrial, scientific and medical (ISM) band at 2.4 to 2.485 GHz. Bluetooth® 4.2 offers enhanced privacy and security mechanisms and increases speed and reliability of data transfers. For the purpose of this specification is Bluetooth® class 2 radio used with a range up to 10 meters. More information on Bluetooth® 4.2 is available on www.bluetooth.com (https://www.bluetooth.org/en-us/specification/adopted-specifications?_ga=1.215147412.2083380574.1435305676).

The Communication shall be established with the communications equipment after a pairing process has been completed by an authorized device. As Bluetooth® is using a master/slave model to control when and where devices can send data, the tachograph will play the role of master while the external device will be the slave.

When an external device comes within range of the VU for the first time, the Bluetooth® pairing process can be initiated (see also annex 2). The devices share their addresses, names, and profiles and common secret key, which allows them to bond whenever they are together in the future. Once this step is completed, the external device is trusted and is in state to initiate requests to download data from the tachograph. It is not foreseen to add encryption mechanisms beyond what Bluetooth® provides. However, if additional security mechanisms are needed, this will be done in accordance with Appendix 11 Common Security Mechanisms.

The overall communication principle is described in the following figure.

The SPP (Serial Port Profile) profile of Bluetooth® shall be used to transfer data from the VU to the external device.
 4.3. 
For security reasons, the VU will require a PIN code authorization system separated from the Bluetooth pairing. Each VU shall be able to generate PIN codes for authentication purposes composed of at least 4 digits. Every time an external device pairs with the VU, it must provide the correct PIN code before receiving any data.

Succeeding entering the PIN shall result in putting the device on the whitelist. The whitelist shall store at least 64 devices paired with the particular VU.

Failing to provide the correct PIN code three times in a row shall result in putting temporarily the device on the blacklist. While blacklisted, every new attempt from the device shall be rejected. Further failure to provide the correct PIN code three times in a row shall result in increasingly longer ban duration (See table 1). Providing the correct PIN code shall reset the ban duration and the number of attempt. Figure 1 in Annex 2 represents the sequence diagram of a PIN validation attempt.


Number of consecutive failure Ban duration
3 30 seconds
6 5 minutes
9 1 hour
12 24 hours
15 Permanent

Failing to provide the correct PIN code fifteen times (5×3) in a row shall result in a permanent blacklisting of the ITS Unit. Only providing the correct PUC code shall overturn this permanent ban.

The PUC code shall be composed of 8 digits and provided by the manufacturer with the VU. Failing to provide the correct PUC code ten times in a row will irrevocably blacklist the ITS Unit.

While the manufacturer may offer an option to change the PIN code directly through the VU, the PUC code shall not be alterable. Modifying the PIN code, if possible, shall require to enter the current PIN code directly in the VU.

Furthermore any devices stored in the whitelist shall be kept until manual removal of by the user (e.g. via the man-machine-interface of the VU or other means). By doing so lost or stolen ITS-units may be removed from the whitelist. Also, any ITS Unit leaving the Bluetooth connection range for more than 24 hours shall be automatically removed from the VU whitelist and must provide the correct PIN code again when the connection is established again.

The format of the messages between the VU interface and the VU are not provided but left to the discretion of the manufacturer. Said manufacturer shall however ensure the message format between the ITS Unit and the VU interface is respected (see ASN.1 specifications).

Any data request shall thus be met with the proper verification of the sender's credential before any form of treatment. Figure 2 of Annex 2 represents the sequence diagram for this procedure. Any blacklisted device shall receive an automatic rejection, any non-blacklisted non-whitelisted device shall receive a PIN request it needs to fulfill before resending its data request.
 4.4. 
All messages exchanged between the ITS Unit and the VU interface shall be formatted with a structure consisting of three parts: A header composed by a target byte (TGT), a source byte (SRC) and a length byte (LEN).

The data field composed by a service identifier byte (SID) and a variable amount of data bytes (maximum 255).

The checksum byte is the 1 byte sum series modulo 256 of all the bytes of the message excluding the CS itself.

The message shall be Big Endian.


Header Data Field Checksum
TGT SRC LEN SID TRTP CC CM DATA CS
3 bytes Max. 255 bytes 1 byte

TGT and SRC: the ID of the Target (TGT) and Source (SRC) devices of the message. The VU Interface shall have the default ID “EE”. This ID cannot be changed. The ITS Unit shall use the default ID “A0” for its first message of the communication session. The VU Interface shall then assign an unique ID to the ITS Unit and informs it of this ID for future messages during the session.

The LEN byte shall only take into account the ‘DATA’ part of the Data Field (see Table 2), the 4 first bytes are implicit.

The VU Interface shall confirm the authenticity of the message's sender by cross-checking its own IDList with the Bluetooth data by checking the ITS Unit listed at the provided ID is currently in the range of the Bluetooth connection.

Besides the SID, the Data Field shall also contain other parameters: a transfer request parameter (TRTP) and Counter bytes.

If the data to be handled is larger than the available space in one message, it will be split in several submessages. Each submessage shall have the same Header and SID, but will contain a 2-bytes counter, Counter Current (CC) and Counter Max (CM), to indicate the submessage number. To enable error checking and abort the receiving device acknowledges every submessage. The receiving device can accept the submessage, ask for it to be re-transmitted, request the sending device to start again or abort the transmission.

If not used, CC and CM shall be given the value 0xFF.

For instance, the following message


HEADER SID TRTP CC CM DATA CS
3 bytes Longer than 255 bytes 1 byte

Shall be transmitted as such:


HEADER SID TRTP 01 n DATA CS
3 bytes 255 bytes 1 byte


HEADER SID TRTP 02 n DATA CS
3 bytes 255 bytes 1 byte

…


HEADER SID TRTP N N DATA CS
3 bytes Max. 255 bytes 1 byte

Table 3 contains the messages the VU and the ITS Unit shall be able to exchange. The content of each parameter is given in hexadecimal. Aren't represented in the table CC and CM for clarity, see above for complete format.


Message Header DATA Checksum
TGT SRC LEN SID TRTP DATA 
RequestPIN ITSID EE 00 01 FF  
SendITSID ITSID EE 01 02 FF ITSID 
SendPIN EE ITSID 04 03 FF 4*INTEGER (0..9) 
PairingResult ITSID EE 01 04 FF BOOLEAN (T/F) 
SendPUC EE ITSID 08 05 FF 8*INTEGER (0..9) 
BanLiftingResult ITSID EE 01 06 FF BOOLEAN (T/F) 
RequestRejected ITSID EE 08 07 FF Time 
RequestData 
standardTachData EE ITSID 01 08 01  
personalTachData EE ITSID 01 08 02  
gnssData EE ITSID 01 08 03  
standardEventData EE ITSID 01 08 04  
personalEventData EE ITSID 01 08 05  
standardFaultData EE ITSID 01 08 06  
manufacturerData EE ITSID 01 08 07  
ResquestAccepted ITSID EE Len 09 TREP Data 
DataUnavailable 
No data available ITSID EE 02 0A TREP 10 
Personal data not shared ITSID EE 02 0A TREP 11 
NegativeAnswer 
General reject ITSID EE 02 0B SID Req 10 
Service not supported ITSID EE 02 0B SID Req 11 
Sub function not supported ITSID EE 02 0B SID Req 12 
Incorrect message length ITSID EE 02 0B SID Req 13 
Conditions not correct or request sequence error ITSID EE 02 0B SID Req 22 
Request out of range ITSID EE 02 0B SID Req 31 
Response pending ITSID EE 02 0B SID Req 78 
ITSID Mismatch ITSID EE 02 0B SID Req FC 
ITSID Not Found ITSID EE 02 0B SID Req FB 

This message is issued by the VU Interface if a non-blacklisted but non-whitelisted ITS unit is sending any data request.

This message is issued by the VU Interface whenever a new device is sending a request. This device shall use the default ID “A0” before getting assigned an unique ID for the communication session.

This message is issued by the ITS Unit to be whitelisted from the VU interface. The content of this message is a 4 INTEGER between 0 and 9 code.

This message is issued by the VU Interface to inform the ITS Unit if the PIN code it sent was correct. The content of this message shall be a BOOLEAN with the value ‘True’ if the PIN code was correct and ‘False’ otherwise.

This message is issued by the ITS Unit to lift a blacklist sanction from the VU interface. The content of this message is a 8 INTEGER between 0 and 9 code.

This message is issued by the VU Interface to inform the ITS Unit if the PUC code it sent was correct. The content of this message shall be a BOOLEAN with the value ‘True’ if the PUC code was correct and ‘False’ otherwise.

This message is issued by the VU Interface as a reply to any message from a blacklisted ITS Unit except ‘SendPUC’. The message shall contain the remaining time the ITS Unit is blacklisted, following the ‘Time’ sequence format as defined in Annex 3.

This message for data accessing is issued by the ITS Unit. A one byte transfer request parameter (TRTP) indicates the type of data required. There are several types of data:


— standardTachData (TRTP 01): Data available from the tachograph classified as non-personal.
— personalTachData (TRTP 02): Data available from the tachograph classified as personal.
— gnssData (TRTP 03): GNSS data, always personal.
— standardEventData (TRTP 04): Recorded event data classified as non-personal.
— personalEventData (TRTP 05): Recorded event data classified as personal.
— standardFaultData (TRTP 06): Recorded faults classified as non-personal.
— manufacturerData (TRTP 07): data made available by the manufacturer.

See Annex 3 of this appendix for more information about the content of each data type.

See Appendix 12 for more information about the format and content of GNSS data.

See Annex IB and IC for more information about event data code and faults.

This message is issued by the VU Interface if a ITS Unit ‘RequestData’ message has been accepted. This message contains a 1-byte TREP, which is the TRTP byte of the associated RequestData message, and all the data of the requested type.

This message is issued by the VU Interface if, for a certain reason, the requested data aren't available to be sent to a whitelisted ITS Unit. The message contains a 1byte TREP which is the TRTP of the required data and a 1 byte error code specified in the table 3. The Following codes are available:


— No data available (10): The VU interface can't access the VU data for unspecified reasons.
— Personal data not shared (11): The ITS Unit tries to retrieve personal data when they are not shared.

These messages are issued by the VU Interface if a request cannot be completed for any other reason than the unavailability of the data. These messages are typically the result of a bad request format (Length, SID, ITSID…) but aren't limited to that. The TRTP in the Data Field contains the SID of the request. The Data Field contains a code identifying the reason of the negative answer. The following codes are available:


— General Reject (code: 10)
— The action can't be performed for a reason which isn't cited below nor in section (Enter DataUnavailable section number).
— Service not supported (code: 11)
— The request's SID isn't understood.
— Sub function not supported (code: 12)
— The request's TRTP isn't understood. It can be for instance missing or out of accepted values.
— Incorrect message length (code: 13)
— The length of the received message is wrong (mismatch between the LEN byte and the actual message length).
— Conditions not correct or request sequence error (code: 22)
— The required service is not active or the sequence of request messages is not correct
— Request out of range (code: 33)
— The request parameter record (data field) is not valid
— Response pending (code: 78)
— The action requested cannot be completed in time and the VU is not ready to accept another request.
— ITSID Mismatch (code: FB)
— The SRC ITSID doesn't match the associated device after comparison with the Bluetooth information.
— ITSID Not Found (code: FC)
— The SRC ITSID isn't associated with any device.

Lines 1 through 72 (FormatMessageModule) of the ASN.1 code in Annex 3 specify the messages format as described in table 3. More details about the messages content is given below.
 4.5. 
All the data available are classified as either standard or personal. Personal data shall only be accessible if the driver gave his/her consent, accepting his/her tachograph personal data can leave the vehicle network for third party applications.

Driver consent is given when, at first insertion of a given driver card or workshop card currently unknown to the vehicle unit, the cardholder is invited to express his consent for tachograph related personal data output through the optional ITS interface. (see also Annex I C paragraph 3.6.2).

The consent status (enabled/disabled) is recorded in the memory of the tachograph.

In case of multiple drivers, only the personal data about the drivers who gave their consent shall be shared with the ITS interface. For instance, if there's two drivers in the vehicle, and only the first driver accepted to share his personal data, the ones concerning the second driver shall not be shared.
 4.6. 
Figure 3 of Annex 2 represents the sequence diagrams of a valid request sent by the ITS Unit to access standard data. The ITS Unit is properly whitelisted and isn't requesting personal data, no further verification is required. The diagrams consider the proper procedure illustrated in Figure 2 of Annex 2 has already been followed. They can be equated to the REQUEST TREATMENT gray box of Figure 2.

Amongst available data, shall be considered standard:


— standardTachData (TRTP 01)
— StandardEventData (TRTP 04)
— standardFaultData (TRTP 06)
 4.7. 
Figure 4 of Annex 2 represents the sequence diagram for personal data request processing. As previously stated, the VU interface shall only send personal data if the driver has given his explicit consent (see also 4.5). Otherwise, the request must be automatically rejected.

Amongst available data, shall be considered personal:


— personalTachData (TRTP 02)
— gnssData (TRTP 03)
— personalEventData (TRTP 05)
— manufacturerData (TRTP 07)
 4.8. 
ITS units shall be able to request events data containing the list of all the unexpected events. These data are considered standard or personal, see Annex 3. The content of each event is in accordance with the documentation provided in Annex 1 of this appendix.

ANNEX 1
(1) 

Data Source Data classification (personal/not personal)
VehicleIdentificationNumber Vehicle Unit not personal
CalibrationDate Vehicle Unit not personal
TachographVehicleSpeed speed instant t Vehicle Unit personal
Driver1WorkingState Selector driver Vehicle Unit personal
Driver2WorkingState Vehicle Unit personal
DriveRecognize Speed Threshold detected Vehicle Unit not personal
Driver1TimeRelatedStates Weekly day time Driver Card personal
Driver2TimeRelatedStates Driver Card personal
DriverCardDriver1 Vehicle Unit not personal
DriverCardDriver2 Vehicle Unit not personal
OverSpeed Vehicle Unit personal
TimeDate Vehicle Unit not personal
HighResolutionTotalVehicleDistance Vehicle Unit not personal
ServiceComponentIdentification Vehicle Unit not personal
ServiceDelayCalendarTimeBased Vehicle Unit not personal
Driver1Identification Driver Card personal
Driver2Identification Driver Card personal
NextCalibrationDate Vehicle Unit not personal
Driver1ContinuousDrivingTime Driver Card personal
Driver2ContinuousDrivingTime Driver Card personal
Driver1CumulativeBreakTime Driver Card personal
Driver2CumulativeBreakTime Driver Card personal
Driver1CurrentDurationOfSelectedActivity Driver Card personal
Driver2CurrentDurationOfSelectedActivity Driver Card personal
SpeedAuthorised Vehicle Unit not personal
TachographCardSlot1 Driver Card not personal
TachographCardSlot2 Driver Card not personal
Driver1Name Driver Card personal
Driver2Name Driver Card personal
OutOfScopeCondition Vehicle Unit not personal
ModeOfOperation Vehicle Unit not personal
Driver1CumulatedDrivingTimePreviousAndCurrentWeek Driver Card personal
Driver2CumulatedDrivingTimePreviousAndCurrentWeek Driver Card personal
EngineSpeed Vehicle Unit personal
RegisteringMemberState Vehicle Unit not personal
VehicleRegistrationNumber Vehicle Unit not personal
Driver1EndOfLastDailyRestPeriod Driver Card personal
Driver2EndOfLastDailyRestPeriod Driver Card personal
Driver1EndOfLastWeeklyRestPeriod Driver Card personal
Driver2EndOfLastWeeklyRestPeriod Driver Card personal
Driver1EndOfSecondLastWeeklyRestPeriod Driver Card personal
Driver2EndOfSecondLastWeeklyRestPeriod Driver Card personal
Driver1CurrentDailyDrivingTime Driver Card personal
Driver2CurrentDailyDrivingTime Driver Card personal
Driver1CurrentWeeklyDrivingTime Driver Card personal
Driver2CurrentWeeklyDrivingTime Driver Card personal
Driver1TimeLeftUntilNewDailyRestPeriod Driver Card personal
Driver2TimeLeftUntilNewDailyRestPeriod Driver Card personal
Driver1CardExpiryDate Driver Card personal
Driver2CardExpiryDate Driver Card personal
Driver1CardNextMandatoryDownloadDate Driver Card personal
Driver2CardNextMandatoryDownloadDate Driver Card personal
TachographNextMandatoryDownloadDate Vehicle Unit not personal
Driver1TimeLeftUntilNewWeeklyRestPeriod Driver Card personal
Driver2TimeLeftUntilNewWeeklyRestPeriod Driver Card personal
Driver1NumberOfTimes9hDailyDrivingTimesExceeded Driver Card personal
Driver2NumberOfTimes9hDailyDrivingTimesExceeced Driver Card personal
Driver1CumulativeUninterruptedRestTime Driver Card personal
Driver2CumulativeUninterruptedRestTime Driver Card personal
Driver1MinimumDailyRest Driver Card personal
Driver2MinimumDailyRest Driver Card personal
Driver1MinimumWeeklyRest Driver Card personal
Driver2MinimumWeeklyRest Driver Card personal
Driver1MaximumDailyPeriod Driver Card personal
Driver2MaximumDailyPeriod Driver Card personal
Driver1MaximumDailyDrivingTime Driver Card personal
Driver2MaximumDailyDrivingTime Driver Card personal
Driver1NumberOfUsedReducedDailyRestPeriods Driver Card personal
Driver2NumberOfUsedReducedDailyRestPeriods Driver Card personal
Driver1RemainingCurrentDrivingTime Driver Card personal
Driver2RemainingCurrentDrivingTime Driver Card personal
GNSS position Vehicle Unit personal
 (2) 
See Appendix 12 — GNSS.
 (3) 

Event Storage rules Data to be recorded per event
Insertion of a non-valid card 
— the 10 most recent events. 
— date and time of event,
— card(s) type, number, issuing Member State and generation of the card creating the event.
— number of similar events that day
Card conflict 
— the 10 most recent events. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of the two cards creating the conflict.
Last card session not correctly closed 
— the 10 most recent events. 
— date and time of card insertion,
— card(s) type, number, issuing Member State and generation,
— last session data as read from the card:
— date and time of card insertion,
— VRN, Member State of registration and VU generation.
Power supply interruption (2) 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Communication error with the remote communication facility 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Absence of position information from GNSS receiver 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Communication error with the external GNSS facility
                                           
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Motion data error 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Vehicle motion conflict 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Security breach attempt the 10 most recent events per type of event. 
— date and time of beginning of event,
— date and time of end of event (if relevant),
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— type of event.
Time conflict 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— recording equipment date and time
— GNSS date and time,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
 (4) 

Event Storage rules Data to be recorded per event
Driving without an appropriate card 
— the longest event for each of the 10 last days of occurrence,
— the 5 longest events over the last 365 days. 
— date and time of beginning of event,
— date and time of end of event,
— card(s) type, number, issuing Member State and generation of any card inserted at beginning and/or end of the event,
— number of similar events that day.
Card insertion while driving 
— the last event for each of the 10 last days of occurrence, 
— date and time of the event,
— card(s) type, number, issuing Member State and generation,
— number of similar events that day
Over speeding (1) 
— the most serious event for each of the 10 last days of occurrence (i.e. the one with the highest average speed),
— the 5 most serious events over the last 365 days.
— the first event having occurred after the last calibration 
— date and time of beginning of event,
— date and time of end of event,
— maximum speed measured during the event,
— arithmetic average speed measured during the event,
— card type, number, issuing Member State and generation of the driver card (if applicable),
— number of similar events that day.
 (5) 

Fault Storage rules Data to be recorded per fault
Card fault 
— the 10 most recent driver card faults. 
— date and time of beginning of fault,
— date and time of end of fault,
— card(s) type, number, issuing Member State and generation.
Recording equipment faults 
— the 10 most recent faults for each type of fault,
— the first fault after the last calibration. 
— date and time of beginning of fault,
— date and time of end of fault,
— type of fault,
— card(s) type, number and issuing Member State and generation of any card inserted at beginning and/or end of the fault.

This fault shall be triggered for any of these failures, while not in calibration mode:


— VU internal fault
— Printer fault
— Display fault
— Downloading fault
— Sensor fault
— GNSS receiver or external GNSS facility fault
— Remote Communication facility fault
— ITS interface fault (if applicable)
 (6) 

Event or Fault Storage rules Data to be recorded per event
To be defined by Manufacturer To be defined by Manufacturer To be defined by Manufacturer

ANNEX 2
Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
ANNEX 3
Appendix 14 1. 
This Appendix specifies the design and the procedures to follow in order to perform the remote communication function (the Communication) as required in Article 9 of Regulation (EU) No 165/2014 (the Regulation).
 DSC_1 
It is important to comprehend that this functionality is intended to serve only as a pre-filter in order to select vehicles for closer inspection, and it does not replace the formal inspection process as determined in the provisions of Regulation (EU) No 165/2014. See recital 9 in the preamble of this regulation, stating that remote communication between the tachograph and control authorities for roadside control purposes facilitates targeted roadside checks.
 DSC_2 The Data shall be exchanged using the Communication which shall be a wireless intercourse using 5.8 GHz DSRC wireless communications consistent with this Appendix and tested against the appropriate parameters of EN 300 674-1, {Electromagnetic compatibility and Radio spectrum Matters (ERM); Road Transport and Traffic Telematics (RTTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and Medical (ISM) band; Part 1: General characteristics and test methods for Road Side Units (RSU) and On -Board Units (OBU)}.
 DSC_3 The Communication shall be established with the communications equipment only when so requested by the equipment of the competent control authority using compliant radio-communication means (the Remote early detection communication reader (REDCR)).
 DSC_4 The Data shall be secured to ensure integrity.
 DSC_5 Access to the Data communicated shall be restricted to competent control authorities authorised to check infringements of Regulation (EC) No 561/2006 and of Regulation (EU) No 165/2014 and to workshops in so far as it is necessary to verify the correct functioning of the tachograph.
 DSC_6 The Data exchanged during the Communication shall be limited to the data necessary for the purpose of targeting roadside checks of vehicles with a potentially manipulated or misused tachograph.
 DSC_7 Data integrity and security shall be obtained by securing the Data within the Vehicle Unit (VU) and by passing only the secured payload data and security related data (see 5.4.4) across the wireless 5.8 GHz DSRC remote communication medium, meaning that only authorised persons of competent control authorities have the means to understand the data passed across the Communication and to verify its authenticity. See Appendix 11 Common Security Mechanisms.
 DSC_8 The Data shall contain a timestamp for the time of its last update.
 DSC_9 The content of the security data shall be known only to and within the control of the competent control authorities, and those parties with whom they share this information and is outwith the provisions of the Communication that is the subject of this Appendix, save that the Communication makes provision to transfer a packet of security data with every packet of payload data.
 DSC_10 The same architecture and equipment shall be capable be used to acquire other data concepts (such as weigh–on-board) using the architecture specified herein.
 DSC_11 For clarification, in accordance with the provisions of Regulation (EU) No 165/2014 (Article 7), data concerning the identity of the driver shall not be communicated across the Communication.
 2. 
The scope of this Appendix is to specify how agents of the competent control authorities use a specified 5.8 GHz DSRC wireless communication to remotely obtain data (the Data) from a targeted vehicle that identifies that the targeted vehicle is in potential violation of Regulation (EU) No 165/2014 and should be targeted for consideration to be stopped for further investigation.

Regulation (EU) No 165/2014 requires that the Data collected shall be limited to data or pertaining to data that identifies a potential infringement, as defined in Article 9 of Regulation (EU) No 165/2014.

In this scenario, the time available for communication is limited, because 
                                 the Communication
                               is targeted and of a short- range design. Further, the same communication means for remote tachograph monitoring (RTM) may also be used by the competent control authorities for other applications (such as the maximal weights and dimensions for heavy goods vehicles defined in Directive (EU) 2015/719) and such operations may be separate or sequential at the discretion of the competent control authorities.

This Appendix specifies:


— The communications equipment, procedures and protocols to be used for the Communication
— The Standards and Regulations to which the radio equipment shall comply
— The presentation of the Data to the Communication equipment
— The enquiry and download procedures and sequence of operations
— The Data to be transferred
— Potential interpretation of the Data transferred across the Communication
— The provisions for security data relating to the Communication
— The availability of the Data to the competent control authorities
— How the Remote early detection communication reader can request different freight and fleet data concepts

For clarification, this Appendix does not specify:


— the collection of the Data operation and management within the VU (which shall be a function of product design unless specified elsewhere within Regulation (EU) No 165/2014)
— the form of presentation of collected data to the agent of the competent control authorities, nor the criteria which shall be used by the competent control authorities to decide which vehicles to stop (which shall be a function of product design unless specified elsewhere within Regulation (EU) No 165/2014 or a policy decision of the competent control authorities). For clarification: the Communication only makes the Data available to the competent control authorities in order that they may make informed decisions
— Data security provisions (such as encryption) concerning the content of the Data (which shall be specified within Appendix 11 Common Security Mechanisms).
— detail of any data concepts other than RTM which may be obtained using the same architecture and equipment
— detail of the behaviour and management between VU's and the DSRC-VU, nor the behaviour within the DSRC-VU (other than to provide the Data when so requested by an REDCR).
 3. 
The following acronyms and definitions specific to this Appendix are used in this appendix:

the Antennaelectrical device which converts electric power into radio waves, and vice versa used in combination with a radio transmitter or radio receiver. In operation, a radio transmitter supplies an electric current oscillating at radio frequency to the antenna's terminals, and the antenna radiates the energy from the current as electromagnetic waves (radio waves). In reception, an antenna intercepts some of the power of an electromagnetic wave in order to produce a tiny voltage at its terminals, that is applied to a receiver to be amplifiedthe Communicationexchange of information/data between a DSRC-REDCR and a DSRC-VU according to section 5 in a master-slave relationship to obtain the Data.the Datasecured data of defined format (see 5.4.4) requested by the DSRC-REDCR and provided to the DSRC-REDCR by the DSRC-VU across a 5.8 GHz DSRC link as defined in 5 belowRegulation (EC) No 165/2014Regulation (EU) No 165/2014 of the European Parliament and of the Council of 4 February 2014 on tachographs in road transport, repealing Council Regulation (EEC) No 3821/85 on recording equipment in road transport and amending Regulation (EC) No 561/2006 of the European Parliament and of the Council on the harmonisation of certain social legislation relating to road transportAIDApplication IdentifierBLEBluetooth Low EnergyBSTBeacon Service TableCIWDCard insertion while drivingCRCcyclic redundancy checkDSC (n)identifier of a requirement for a specific DSRC appendixDSRCDedicated Short Range CommunicationDSRC-REDCRDSRC — Remote Early Detection Communication Reader.DSRC-VUDSRC — Vehicle Unit. This is the ‘remote early detection facility’ defined in Annex 1C.DWVCDriving without valid cardEIDElement IdentifierLLCLogical Link ControlLPDULLC Protocol Data UnitOWSOnboard Weighing SystemPDUProtocol Data UnitREDCRRemote early detection communication reader. This is the ‘remote early detection communication reader equipment’ defined in Annex 1C.RTMRemote Tachograph MonitoringSM-REDCRSecurity Module-Remote early detection communication readerTARVTelematics Applications for Regulated Vehicles (ISO 15638 series of Standards)VUVehicle UnitVUPMVehicle Unit Payload MemoryVUSMVehicle Unit Security ModuleVSTVehicle Service TableWIMWeigh in motionWOBWeigh on board

The specification defined in this Appendix refers to and depends upon all or parts of the following regulations and standards. Within the clauses of this Appendix the relevant standards, or relevant clauses of standards, are specified. In the event of any contradiction the clauses of this Appendix shall take precedence. In the event of any contradiction where no specification is clearly determined in this Appendix, operating within ERC 70-03 (and tested against the appropriate parameters of EN 300 674-1) shall take precedence, followed in descending order of preference by EN 12795, EN 12253 EN 12834 and EN 13372, 6.2, 6.3, 6.4 and 7.1.

Regulations and standards referenced in this Appendix are:


[[1]] Regulation (EU) No 165/2014 of the European Parliament and of the Council of 4 February 2014 on tachographs in road transport, repealing Council Regulation (EEC) No 3821/85 on recording equipment in road transport and amending Regulation (EC) No 561/2006 of the European Parliament and of the Council on the harmonisation of certain social legislation relating to road transport.
[[2]] Regulation (EC) No 561/2006 of the European Parliament and of the Council of 15 March 2006 on the harmonisation of certain social legislation relating to road transport and amending Council Regulations (EEC) No 3821/85 and (EC) No 2135/98 and repealing Council Regulation (EEC) No 3820/85 (Text with EEA relevance).
[[3]] ERC 70-03 CEPT: ECC Recommendation 70-03: Relating to the Use of Short Range Devices (SRD)
[[4]] ISO 15638 Intelligent transport systems — Framework for cooperative telematics applications for regulated commercial freight vehicles (TARV).
[[5]] EN 300 674-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); Road Transport and Traffic Telematics (RTTT); Dedicated Short Range Communication (DSRC) transmission equipment (500 kbit/s / 250 kbit/s) operating in the 5,8 GHz Industrial, Scientific and Medical (ISM) band; Part 1: General characteristics and test methods for Road Side Units (RSU) and On-Board Units (OBU).
[[6]] EN 12253 Road transport and traffic telematics — Dedicated short-range communication — Physical layer using microwave at 5.8 GHz.
[[7]] EN 12795 Road transport and traffic telematics — Dedicated short-range communication — Data link layer: medium access and logical link control.
[[8]] EN 12834 Road transport and traffic telematics — Dedicated short-range communication — Application layer.
[[9]] EN 13372 Road transport and traffic telematics — Dedicated short-range communication — Profiles for RTTT applications
[[10]] ISO 14906 Electronic fee collection — Application interface definition for dedicated short- range communication
 4.  4.1 
Regulation (EU) No 165/2014 provides specific and controlled scenarios within which the Communication is to be used.

The scenarios supported are:

'Communication Profile 1: Roadside inspection using a short range wireless communication Remote Early Detection Communication Reader instigating a physical roadside inspection (master-:-slave)Reader Profile 1a: via a hand aimed or temporary roadside mounted and aimed Remote Early Detection CommunicationReader Profile 1b: via a vehicle mounted and directed Remote Early Detection Communication Reader'.
 4.1.1 NOTE: In order to understand the context of the preconditions the reader is referred to Figure 14.3 below. 4.1.1.1  DSC_12 The VU shall be responsible to keep updated every 60 seconds and maintain the data to be stored in the VU, without any involvement of the DSRC communication function. The means by which this is achieved is internal to the VU, specified in Regulation (EU) No 165/2014, Annex 1 C, section 3.19 ‘Remote communication for targeted roadside checks’ and is not specified in this Appendix.
 4.1.1.2  DSC_13 The VU shall be responsible to update the DSRC tachograph data (the Data) whenever the data stored in the VU is updated at the interval determined in 4.1.1.1 (DSC_12), without any involvement of the DSRC communication function.
 DSC_14 The VU data shall be used as a basis to populate and update the Data, the means by which this is achieved, is specified in Annex 1.C, section 3.19 ‘Remote communication for targeted roadside checks’ or if there is no such specification it is a function of product design and is not specified in this Appendix. For the design of the connection between DSRC-VU facility and the VU, please refer to section 5.6.
 4.1.1.3  DSC_15 The content and format of the Data shall be such that, once decrypted, it shall be structured and made available in the form and format specified in 5.4.4 of this Appendix (Data structures).
 4.1.1.4  DSC_16 The Data, having been kept frequently updated in accordance with the procedures determined in 4.1.1.1, shall be secured prior to presentation to the DSRC-VU, and presented as a secured data concept value, for temporary storage in the DSRC-VU as the current version of the Data. This data is transferred from the VUSM to the DSRC function VUPM. The VUSM and VUPM are functions and not necessarily physical entities. The form of physical instantiation to perform these functions shall be a matter of product design unless specified elsewhere in Regulation (EU) No 165/2014.
 4.1.1.5  DSC_17 Security data (securityData), comprising the data required by the REDCR to complete its ability to decrypt the Data shall be supplied as defined in Appendix 11 Common Security Mechanisms and presented as a data concept value, for temporary storage in the DSRC-VU as the current version of securityData, in the form defined in this Appendix section 5.4.4.
 4.1.1.6  DSC_18 The data concept which shall always be available in the DSRC function VUPM for immediate transfer upon request by the REDCR is defined in section 5.4.4 for full ASN.1 Module specifications.

This profile covers the use case where an agent of the competent control authorities, uses a short range remote communication Remote Early Detection Communication Reader (5.8 GHz DSRC interfaces operating within ERC 70-03, and tested against the appropriate parameters of EN 300 674-1 as described in section 5) (the REDCR) to remotely identify a vehicle which is potentially in violation of Regulation (EU) No 165/2014. Once identified, the agent of the competent control authorities who is controlling the interrogation decides whether the vehicle should be stopped.
 4.1.2 
In this use case the agent of the competent control authorities is situated at the roadside, and aims a hand held, tripod mounted, or similar portable, REDCR from the roadside towards the centre of the windshield of the targeted vehicle. The interrogation is made using 5.8 GHz DSRC interfaces operating within ERC 70-03, and tested against the appropriate parameters of EN 300 674-1 as described in section 5. See Figure 14.1 (Use Case 1).

Figure 14.1 4.1.3 
In this use case the agent of the competent control authorities is situated within a moving vehicle, and either aims a hand held, portable REDCR from the vehicle towards the centre of the windshield of the targeted vehicle, or the REDCR is mounted within or on the vehicle so as to point towards the centre of the windshield of the targeted vehicle when the Remote Early Detection Communication Reader's vehicle is in a particular position relevant to the targeted vehicle (for example directly ahead in a stream of traffic). The interrogation is made using 5.8 GHz DSRC interfaces operating within ERC 70-03, and tested against the appropriate parameters of EN 300 674-1 as described in section 5. See Figure 14.2. (Use Case 2).

Figure 14.2 4.2 
To give the possibility to verify the authenticity and integrity of downloaded data through the remote communication, the secured Data is verified and decrypted in accordance with Appendix 11 Common Security Mechanisms.
 5.  5.1 
The design of the remote communication function in the Smart Tachograph is shown as described in Figure 14.3.

Figure 14.3 DSC_19 

— Security Module (VUSM). This function present in the VU is responsible for securing the Data which is to be transmitted from the DSRC-VU to the agent of the competent control authorities via remote communication.
— The secured data is stored in the VUSM memory. At intervals determined in 4.1.1.1 (DSC_12), the VU encrypts and replenishes the RTMdata concept (which comprises payload data and security data concept values determined below in this Appendix) held in the memory of the DSRC-VU. The operation of the security module is defined in Appendix 11 Common Security Mechanisms and outwith the scope of this Appendix, save that it shall be required to provide updates to the VU Communication facility each time the VUSM data changes.
— The communication between the VU and the DSRC-VU may be a wired communication or a Bluetooth Low Energy (BLE) communication, and the physical location of the DSRC-VU may be integral with the antenna on the windshield of the vehicle, may be internal to the VU, or located somewhere between.
— The DSRC-VU shall have a reliable source of power available at all times. The means by which it is provided with its power is a design decision.
— The memory of the DSRC-VU shall be non-volatile in order to maintain the Data in the DSRC-VU even when the vehicle ignition is switched off.
— If the communication between the VU and the DSRC-VU is made via BLE and the power source is a non-recharging battery, the power source of the DSRC-VU shall be replaced at every Periodic Inspection, and the manufacturer of the DSRC-VU equipment shall be responsible to ensure that the power supply is adequate to last from one Periodic Inspection to the next Periodic Inspection, maintaining normal access to the data by an REDCR throughout the period without failure or interruption.
— VU RTM ‘payload memory’ facility (VUPM). This function present in the VU is responsible for providing and updating the Data. The content of The Data. (‘TachographPayload’) is defined in 5.4.4/5.4.5 below and is updated at the interval determined in 4.1.1.1 (DSC_12).
— DSRC-VU. This is the function, within or connected to the antenna and in communication with the VU through a wired or wireless (BLE) connection, which holds the current data (VUPM-data) and manages the response to an interrogation across the 5.8 GHz DSRC medium. Disconnection of the DSRC facility or interference during normal vehicle operation with the functioning of the DSRC facility shall be construed as a violation of Regulation (EU) No 165/2014.
— Security module (REDCR) (SM-REDCR) is the function used to decrypt and check integrity of the data originating from the VU. The means by which this is achieved is determined in Appendix 11 Common Security Mechanisms, and is not defined in this Appendix.
— The DSRC facility (REDCR) (DSRC-REDCR) function comprises a 5.8 GHz transceiver and associated firmware and software which manages the Communication with the DSRC-VU according to this Appendix.
— The DSRC-REDCR interrogates the DSRC-VU of the targeted vehicle and obtains the Data (the targeted vehicle's current VUPM-data) via the DSRC link and processes and stores the received data in its SM-REDCR.
— The DSRC-VU antenna shall be positioned at a location where it optimizes the DSRC communication between the vehicle and the roadside reader antenna, when the reader is installed 15 meters distance in front of the vehicle and 2 meters height, targeting the horizontal and vertical centre of the windscreen. For light vehicles an installation corresponding to the upper part of the windscreen is suitable. For all the other vehicles the DSRC antenna shall be installed either near the lower or near the upper part of the windscreen.
 DSC_20 The Antenna and The Communication shall operate within ERC 70-03, tested against the appropriate parameters of EN 300 674-1 as described in section 5. The Antenna and the Communication can implement mitigation techniques against the risk of wireless interference as described in ECC report 228 using e.g., filters in the CEN DSRC 5.8 GHz communication.
 DSC_21 The DSRC antenna shall be connected to the DSRC-VU facility either directly within the module mounted to or close to the windshield, or through a dedicated cable constructed in a manner to make illegal disconnection difficult. Disconnection of or interference with the functioning of Antenna shall be a violation of Regulation (EU) No 165/2014. Deliberate masking or otherwise detrimentally affecting the operational performance of the Antenna shall be construed as a violation of Regulation (EU) No 165/2014.
 DSC_22 The form factor of the antenna is not defined and shall be a commercial decision, so long as the fitted DSRC-VU meets the conformance requirements defined in section 5 below. The antenna shall be positioned as determined in DSC_19 and efficiently support the use cases described in in 4.1.2 and 4.1.3.

Figure 14.4The form factor of the REDCR and its antenna may vary according to the circumstances of the reader (tripod mounted, hand held, vehicle mounted, etc.) and the modus operandi employed by the agent of the competent control authorities.A display and/or notification function is used to present the results of the remote communication function to the agent of the competent control authorities. A display may be provided on a screen, as a printed output, an audio signal, or a combination of such notifications. The form of such display and/or notification is a matter of the requirements of the agents of the competent control authorities and equipment design and is not specified within this Appendix. DSC_23 The design and form factor of the REDCR shall be a function of commercial design, operating within ERC 70-03, and the design and performance specifications defined in this Appendix, (section 5.3.2), thus providing the marketplace maximum flexibility to design and provide equipment to cover the specific interrogation scenarios of any particular competent control authority.
 DSC_24 The design and form factor of the DSRC-VU and its positioning inside or outside the VU shall be a function of commercial design, operating within ERC 70-03 and the design and performance specifications defined in this Appendix (section 5.3.2) and within this Clause (5.1).
 DSC_25 However, the DSRC-VU shall be reasonably capable to accept data concept values from other intelligent vehicle equipment by means of an open industry standard connection and protocols. (For example from weigh on board equipment), so long as such data concepts are identified by unique and known application identifiers/file names, and the instructions to operate such protocols shall be made available to the European Commission, and available without charge to manufacturers of relevant equipment.
 5.2  5.2.1 
The workflow of operations is represented in Figure 14.5.

Figure 14.5The steps are described below:
a.. Whenever the vehicle is in operation (ignition ON) the tachograph is providing data to the VU function. The VU function prepares the Data for the remote communication function (encrypted) and updates the VUPM held in the memory of the DSRC-VU (as defined in 4.1.1.1 — 4.1.1.2). The Data collected shall be formatted as determined in 5.4.4 — 5.4.5 below.
b.. On every occasion that the Data is updated, the timestamp defined in the security data concept shall be updated.
c.. The VUSM function secures the data in accordance with the procedures determined in Appendix 11.
d.. On every occasion that the Data is updated (see 4.1.1.1 — 4.1.1.2), the Data shall be transferred to the DSRC-VU, where it replaces any previous data, in order that updated current data (the Data) shall always be available to be provided in the event of an interrogation by an REDCR. When supplied by the VU to the DSRC-VU the Data shall be identifiable by the filename RTMData or by ApplicationID and Attribute identifiers.
e.. If an agent of the competent control authorities wishes to target a vehicle and collect the Data from the targeted vehicle, the agent of the competent control authorities shall first insert his/her smartcard in the REDCR to enable the Communication and to allow the SM-REDCR to verify its authenticity and decrypt the data.
f.. The agent of the competent control authority then targets a vehicle and requests the data through remote communication. The REDCR opens a 5.8 GHz DSRC interface session with the DSRC-VU of the targeted vehicle, and requests the Data. The Data is transferred to the REDCR through the wireless communication system as a DSRC Attribute using the Application service GET as defined in 5.4. The Attribute contains the encrypted payload data values and the DSRC security data.
g.. The data is analyzed by the REDCR equipment and provided to the agent of the competent control authority.
h.. The agent of the competent control authority uses the data to assist in a decision of whether or not to stop for a detailed inspection, or ask another agent of the competent control authority to stop the vehicle. 5.2.2  DSC_26 Data received across the 5.8 GHz interface shall carry the meaning and import defined in 5.4.4 and 5.4.5 below and only that meaning and import, and shall be understood within the objectives defined therein. In accordance with the provisions of Regulation (EU) No 165/2014, the Data shall be used only to provide relevant information to a competent control authority to assist them to determine which vehicle should be stopped for physical inspection, and shall be subsequently destroyed in accordance with Article 9 of Regulation (EU) No 165/2014.
 5.3  5.3.1  DSC_27 The remote interrogation of vehicles using a 5.8GHz DSRC interface should not be used within 200 metres of an operational 5.8 GHz DSRC gantry.
 5.3.2  DSC_28 The equipment used for remote tachograph monitoring shall conform to and operate within ERC70-03 and the parameters defined in Tables 14.1 and 14.2 below.
 DSC_29 Further, to ensure compatibility with the operational parameters of other standardised 5.8 GHz DSRC systems, the equipment used for remote tachograph monitoring shall conform to parameters from EN 12253 and EN 13372.

Namely:


Item No Parameter Value(s) Remark
D1 Downlink Carrier Frequencies There are four alternatives which may be used by an REDCR:
 5,7975 GHz
 5,8025 GHz
 5,8075 GHz
 5,8125 GHz Within ERC 70-03.Carrier Frequencies may be selected by the implementer of the roadside system and need not be known in the DSRC-VU(Consistent with EN 12253, EN 13372)
D1a Tolerance of Carrier Frequencies within ± 5 ppm (Consistent with EN 12253)
D2 RSU (REDCR) Transmitter Spectrum Mask Within ERC 70-03.REDCR shall be according to Class B,C as defined in EN 12253.No other specific requirement within this Annex Parameter used for controlling interference between interrogators in proximity (as defined in EN 12253 and EN 13372).
D3 OBU(DSRC-VU) Minimum Frequency Range 5,795 — 5,815 GHz (Consistent with EN 12253)
D4 Maximum E.I.R.P. Within ERC 70-03 (unlicensed) and within National RegulationMaximum + 33 dBm (Consistent with EN 12253)
D4a Angular E.I.R.P. mask According to declared and published specification of interrogator designer (Consistent with EN 12253)
D5 Polarisation Left hand circular (Consistent with EN 12253)
D5a Cross-Polarisation XPD:In bore sight: (REDCR) RSU t ≥ 15 dB(DSRC-VU) OBU r ≥ 10 dBAt -3 dB area: (REDCR) RSU t ≥ 10 dB(DSRC-VU) OBU r ≥ 6 dB (Consistent with EN 12253)
D6 Modulation Two level amplitude modulation. (Consistent with EN 12253)
D6a Modulation Index 0,5 ... 0,9 (Consistent with EN 12253)
D6b Eye Pattern ≥ 90 % (time) / ≥ 85 % (amplitude) 
D7 Data Coding FM0‘1’ bit has transitions only at the beginning and end of the bit interval. ‘0’ bit has an additional transition in the middle of the bit interval compared to the ‘1’ bit. (Consistent with EN 12253)
D8 Bit rate 500 kBit/s (Consistent with EN 12253)
D8a Tolerance of Bit Clock better than ± 100 ppm (Consistent with EN 12253)
D9 Bit Error Rate (B.E.R.) for communication ≤ 10– 6 when incident power at OBU (DSRC-VU) is in the range given by [D11a to D11b]. (Consistent with EN 12253)
D10 Wake-up trigger for OBU (DSRC-VU) OBU (DSRC-VU) shall wake up on receiving any frame with 11 or more octets (including preamble) No special wake-up pattern is necessary.DSRC-VU may wake up on receiving a frame with less than 11 octets(Consistent with EN 12253)
D10a Maximum Start Time ≤ 5 ms (Consistent with EN 12253)
D11 Communication zone Spatial region within which a B.E.R. according to D9a is achieved (Consistent with EN 12253)
D11a Power Limit for communication (upper). – 24dBm (Consistent with EN 12253)
D11b Power Limit for communication (lower). Incident power:
 – 43 dBm (boresight)
 – 41 dBm (within – 45° ± 45°Corresponding to the plane parallel to the road surface when the DSRC-VU later is installed in the vehicle (Azimuth)) (Consistent with EN 12253)Extended requirement for horizontal angles up to ±45°, due to the use cases defined in this annex.
D12 Cut-off power level of (DSRC-VU) – 60 dBm (Consistent with EN 12253)
D13 Preamble Preamble is mandatory. (Consistent with EN 12253)
D13a Preamble Length and Pattern 16 bits ± 1 bit of FM0 coded ‘1’ bits (Consistent with EN 12253)
D13b Preamble Wave form An alternating sequence of low level and high level with pulse duration of 2 μs.The tolerance is given byD8a (Consistent with EN 12253)
D13c Trailing Bits The RSU (REDCR) is permitted to transmit a maximum of 8 bits after the end flag. An OBU (DSRC-VU) is not required to take these additional bits into account. (Consistent with EN 12253)



Item No. Parameter Value(s) Remark
U1 Sub-carrier Frequencies A OBU (DSRC-VU) shall support 1,5 MHz and 2,0 MHzAn RSU (REDCR) shall support 1,5 MHz or 2,0 MHz or both. U1-0: 1,5 MHz U1-1: 2,0 MHz Selection of sub-carrier frequency(1,5 MHz or 2,0 MHz) depends on the EN 13372 profile selected.
U1a Tolerance of Sub- carrier Frequencies within ± 0,1 % (Consistent with EN 12253)
U1b Use of Side Bands Same data on both sides (Consistent with EN 12253)
U2 OBU (DSRC-VU) Transmitter Spectrum Mask According to EN12253
1)) Out band power:
see ETSI EN 300674-1
2)) In band power:
[U4a] dBm in 500 kHz
3)) Emission in any other uplink channel:
U2(3)-1 = – 35 dBm in 500 kHz (Consistent with EN 12253)
U4a Maximum Single Side Band E.I.R.P. (boresight) Two options:
 U4a-0: – 14 dBm
 U4a-1: – 21 dBm According to declared and published specification of equipment designer
U4b Maximum Single Side Band E.I.R.P. (35°) Two options:
— Not applicable
— – 17dBm According to declared and published specification of equipment designer
U5 Polarisation Left hand circular (Consistent with EN 12253)
U5a Cross Polarisation XPD:In bore sight: (REDCR) RSU r ≥ 15 dB(DSRC-VU) OBU t ≥ 10 dBAt – 3 dB: (REDCR) RSU r ≥ 10 dB(DSRC-VU) OBU t ≥ 6 dB (Consistent with EN 12253)
U6 Sub-Carrier Modulation 2-PSKEncoded data synchronised with sub-carrier: Transitions of encoded data coincide with transitions of sub- carrier. (Consistent with EN 12253)
U6b Duty Cycle Duty Cycle:50 % ± α, α ≤ 5 % (Consistent with EN 12253)
U6c Modulation on Carrier Multiplication of modulated sub- carrier with carrier. (Consistent with EN 12253)
U7 Data Coding NRZI (No transition at beginning of ‘1’ bit, transition at beginning of ‘0’ bit, no transition within bit) (Consistent with EN 12253)
U8 Bit Rate 250 kbit/s (Consistent with EN 12253)
U8a Tolerance of Bit Clock Within ± 1 000 ppm (Consistent with EN 12253)
U9 Bit Error Rate (B.E.R.) for communication ≤10– 6 (Consistent with EN 12253)
U11 Communication Zone The spatial region within which the DSRC-VU is situated such that its transmissions are received by the REDCR with a B.E.R. of less than that given by U9a. (Consistent with EN 12253)
U12a Conversion Gain (lower limit) 1 dB for each side band Range of angle: Circularly symmetric between bore sight and ± 35°and 
within – 45° ± 45° Corresponding to the plane parallel to the road surface when the DSRC-VU later is installed in the vehicle (Azimuth) Greater that the specified value range for horizontal angles up to ± 45°, due to the use cases defined in this annex.
U12b Conversion Gain (upper limit) 10 dB for each side band Less than the specified value range for each side band within a circular cone around boresight of ± 45° opening angle
U13 Preamble Preamble is mandatory. (Consistent with EN 12253)
U13a PreambleLength and Pattern 32 to 36 μs modulated with sub- carrier only, then 8 bits of NRZI coded ‘0’ bits. (Consistent with EN 12253)
U13b Trailing Bits The DSRC-VU is permitted to transmit a maximum of 8 bits after the end flag. A RSU (REDCR) is not required to take these additional bits into account. (Consistent with EN 12253)

 5.3.3  5.3.3.1  DSC_30 The design of the REDCR antenna shall be a function of commercial design, operating within the limits defined in 5.3.2 which is adapted to optimise the reading performance of the DSRC-REDCR for the specific purpose and read circumstances in which the REDCR has been designed to operate.
 5.3.3.2  DSC_31 The design of the DSRC-VU antenna shall be a function of commercial design, operating within the limits defined in 5.3.2 which is adapted to optimise the reading performance of the DSRC-REDCR for the specific purpose and read circumstances in which the REDCR has been designed to operate.
 DSC_32 The VU antenna shall be fixed to, or close to, the front windshield of the vehicle as specified in 5.1 above.
 DSC_33 In the test environment in a workshop (see section 6.3), a DSRC-VU antenna, affixed according to 5.1 above, shall successfully connect with a standard test communication and successfully provide an RTM transaction as defined within this Appendix, at a distance between 2 and 10 meters, better than 99 % of the time, averaged over 1 000 read interrogations.
 5.4  5.4.1  DSC_34 NOTE The purpose of the initialisation phase (Step 1) is to set up the communication between the REDCR and DSRC-VUs that have entered the 5.8 GHz DSRC (master-slave) transaction zone but have not yet established communication with the REDCR, and to notify the application processes.— Step 1Initialisation. The REDCR sends a frame containing a ‘beacon service table’ (BST) that includes the application identifiers (AIDs) in the service list that it supports. In the RTM application this will simply be the service with the AID value = 2 (Freight&Fleet). The DSRC-VU evaluates the received BST, and shall respond (see below) with the list of the supported applications within the Freight&Fleet domain, or shall not respond if none are supported. If the REDCR does not offer AID=2, the DSRC-VU shall not answer to the REDCR.— Step 2The DSRC-VU sends a frame containing a request for a private window allocation.— Step 3The REDCR sends a frame containing a private window allocation.— Step 4The DSRC-VU uses the allocated private window to send a frame containing its vehicle service table (VST). This VST includes a list of all the different application instantiations that this DSRC-VU supports in the framework of AID=2. The different instantiations shall be identified by means of uniquely generated EIDs, each associated with an Application Context Mark parameter value indicating the application and standard supported.— Step 5Next the REDCR analyses the offered VST, and either terminates the connection (RELEASE) since it is not interested in anything the VST has to offer (i.e. it is receiving a VST from a DSRC-VU that is not supporting the RTM transaction), or, if it receives an appropriate VST it starts an app instantiation.— Step 6To bring this about, the REDCR shall send a frame containing a command to retrieve the RTM data, identifying the RTM application instantiation by specifying the identifier corresponding to the RTM application instantiation (as specified by the DSRC-VU in the VST), and shall allocate a private window.— Step 7The DSRC-VU uses the newly allocated private window to send a frame that contains the addressed identifier corresponding to the RTM application instantiation as provided in the VST, followed by the attribute RtmData (payload element + security element).— Step 8If there are multiple services requested, the value ‘n’ is changed to the next service reference number and the process repeated.— Step 9The REDCR confirms receipt of the data by sending a frame containing a RELEASE command to the DSRC-VU to terminate the session OR if it has failed to validate a successful receipt of the LDPU goes back to step 6.
See Figure 14.6 for a pictorial description of the transaction protocol.

Figure 14.6 5.4.2  DSC_35 
— INITIALISATION.requestA command, issued from the REDCR in the form of a broadcast with definition of applications that the REDCR supports.— INITIALISATION.responseAn answer from the DSRC-VU confirming the connection and containing a list of supported application instances with characteristics and information how to address them (EID).— GET.requestA command, issued from the REDCR to the DSRC-VU, that specifies the application instantiation to be addressed by means of a defined EID, as received in the VST, instructing the DSRC-VU to send the selected attribute(s) with the Data. The objective of the GET command is for the REDCR to obtain the Data from the DSRC-VU.— GET.responseAn answer from the DSRC-VU that contains the Data requested.— ACTION.request ECHOA command, instructing the DSRC-VU to send back data from the DSRC-VU to the REDCR. The objective of the ECHO command is to enable workshops or type approval test facilities to test that the DSRC link is working without needing access to security credentials.— ACTION.response ECHOAn answer from the DSRC VU on the ECHO command.— EVENT_REPORT.request RELEASEA command, instructing the DSRC-VU that the transaction is ended. The objective of the RELEASE command is to end the session with the DSRC-VU. On receipt of the RELEASE the DSRC-VU shall not respond to any further interrogations under the current connection. Note that according to EN 12834 a DSRC-VU will not connect twice to the same interrogator unless it has been out of the communication zone for 255 seconds or if the Beacon ID of the interrogator is changed.
 5.4.3  DSC_36 
Sequence Sender  Receiver Description Action
1 REDCR > DSRC-VU Initialisation of the communication link — Request REDCR broadcasts BST
2 DSRC-VU > REDCR Initialisation of the communication link — Response If BST supports AID=2 then DSRC-VU Requests a private window
3 REDCR > DSRC-VU Grants a private window Sends Frame containing private window allocation
4 DSRC-VU > REDCR Sends VST Sends Frame comprising VST
5 REDCR > DSRC-VU Sends GET.request for data in Attribute for specific EID 
6 DSRC-VU > REDCR Sends GET.response with requested Attribute for specific EID Sends Attribute (RTMData, OWSData….) with data for specific EID
7
                                              
                                                REDCR
                                              
                                                >
                                              
                                                DSRC-VU
                                              
                                                Sends GET.request for data of other Attribute (if appropriate)
                                              
8 DSRC-VU > REDCR Sends GET.response with requested Attribute Sends Attribute with data for specific EID
9 REDCR > DSRC-VU Acknowledges successful receipt of data Sends RELEASE command which closes transaction
10 DSRC-VU   Closes transaction 
An example of the transaction sequence and contents of the exchanged frames is defined in clauses 5.4.7 and 5.4.8
 5.4.4  DSC_37 The semantic structure of the Data when passed across the 5.8 GHz DSRC interface shall be consistent with what described in this Appendix. The way these data are structured is specified in this clause.
 DSC_38 

1.. EncryptedTachographPayload data, which is the encryption of the TachographPayload defined in ASN.1 in section 5.4.5. The method of encryption is described in Appendix 11
2.. DSRCSecurityData, specified in Appendix 11.
 DSC_39 The RTM Data is being addressed as RTM Attribute=1 and is transferred in the RTM container = 10.
 DSC_40 
The ASN.1 module definition for the DSRC data within the RTM application is defined as follows:


 5.4.5  DSC_41 

Table 14.3
Elements of RtmData, actions performed and definitions
(1) RTM Data Element (2) Action performed by the VU  (3) ASN.1 definition of data
RTM1Vehicle Registration Plate The VU shall set the value of the tp15638VehicleRegistrationPlate data element RTM1 from the recorded value of the data type VehicleRegistrationIdentification as defined in Appendix 1 VehicleRegistrationIdentification Vehicle Registration Plate expressed as a string of characters 
RTM2Speeding Event The VU shall generate a boolean value for data element RTM2 tp15638SpeedingEvent.The tp15638SpeedingEvent value shall be calculated by the VU from the number of Over Speeding Events recorded in the VU in the last 10 days of occurrence, as defined in Annex 1C.If there is at least one tp15638SpeedingEvent in the last 10 days of occurrence, the tp15638SpeedingEvent value shall be set to TRUE.ELSE if there are no events in the last 10 days of occurrence, the tp15638SpeedingEvent shall be set to FALSE. 1 (TRUE) — Indicates irregularities in speed within last 10 days of occurrence 
RTM3Driving Without Valid Card The VU shall generate a boolean value for data element RTM3 tp15638DrivingWithoutValidCard.The VU shall assign a value of True to the tp15638DrivingWithoutValidCard variable if the VU data has recorded at least one event in the last 10 days of occurrence of type ‘Driving without an appropriate card’ event as defined in Annex 1C.ELSE if there are no events in the last 10 days of occurrence, the tp15638DrivingWithoutValidCard variable shall be set to FALSE. 1 (TRUE) = Indicates invalid card usage 
RTM4Valid Driver Card The VU shall generate a boolean value for data element RTM4tp15638DriverCard on the basis of the data stored in the VU and defined in Appendix 1.If no valid driver card is present the VU shall set the variable to TRUEELSE if a valid driver card is present the VU shall set the variable to FALSE 0 (FALSE) = Indicates a valid driver card 
RTM5Card Insertion while Driving The VU shall generate a boolean value for data element RTM5.The VU shall assign a value of TRUE to the tp15638CardInsertion variable if the VU data has recorded in the last 10 days of occurrence at least one event of type ‘Card insertion while driving.’ as defined in Annex 1C.ELSE if there are no such events in the last 10 days of occurrence, the tp15638CardInsertion variable shall be set to FALSE. 1 (TRUE) = Indicates card insertion while driving within last 10 days of occurrence 
RTM6Motion Data Error The VU shall generate a boolean value for data element RTM6.The VU shall assign a value of TRUE to the tp15638MotionDataError variable if the VU data has in the last 10 days of occurrence recorded at least one event of type ‘Motion data error’ as defined in Annex 1C.ELSE if there are no such events in the last 10 days of occurrence, the tp15638MotionDataError variable shall be set to FALSE. 1 (TRUE) = Indicates motion data error within last 10 days of occurrence 
RTM7Vehicle Motion Conflict The VU shall generate a boolean value for data element RTM7.The VU shall assign a value of TRUE to the tp15638vehicleMotionConflict variable if the VU data has in the last 10 days recorded at least one event of type Vehicle Motion Conflict (value ‘0A’H ).ELSE if there are no events in the last 10 days of occurrence, the tp15638vehicleMotionConflict variable shall be set to FALSE. 1 (TRUE) = Indicates motion conflict within last 10 days of occurrence 
RTM82nd Driver Card The VU shall generate a boolean value for data element RTM8 on the basis of Annex 1C (‘Driver Activity Data’ CREW and CO-DRIVER).If a 2nd valid driver card is present the VU shall set the variable to TRUEELSE if a 2nd valid driver card is not present the VU shall set the variable to FALSE 1 (TRUE) = Indicates a second driver card inserted 
RTM9Current Activity The VU shall generate a boolean value for data element RTM9.If the current activity is recorded in the VU as any activity other than ‘DRIVING’ as defined in Annex 1C the VU shall set the variable to TRUEELSE if the current activity is recorded in the VU as ‘DRIVING’ the VU shall set the variable to FALSE 1 (TRUE) = other activity selected;0 (FALSE) = driving selected 
RTM10Last Session Closed The VU shall generate a boolean value for data element RTM10.If the last card session was not properly closed as defined in Annex 1C the VU shall set the variable to TRUE.ELSE if the last card session was properly closed the VU shall set the variable to FALSE 1 (TRUE) = improperly closed0 (FALSE) = properly closed 
RTM11Power Supply Interruption The VU shall generate an integer value for data element RTM11.The VU shall assign a value for the tp15638PowerSupplyInterruption variable equal to the longest power supply interruption according to Article 9, Reg (EU) 165/2014 of type ‘Power supply interruption’ as defined in Annex 1C.ELSE if in the last 10 days of occurrence there are have been no Power supply interruption events the value of the integer shall be set to 0.  — Number of power supply interruptions in last 10 days of occurrence
 
RTM12
                                                      
                                                         Sensor Fault
                                                       The VU shall generate an integer value for data element RTM12.The VU shall assign to the variable sensorFault a value of:
— 1 if an event of type ‘35H’ Sensor fault has been recorded in the last 10 days,
— 2 if an event of type GNSS receiver fault (either internal or external with enum values ‘36’H or ‘37’ H) has been recorded in the last 10 days.
— 3 if an event of type ‘0E’H Communication error with the external GNSS facility event has been recorded in the last 10 days.
— 4 If both Sensor Fault and GNSS receiver faults have been recorded in the last 10 days
— 5 If both Sensor Fault and Communication error with the external GNSS facility event have been recorded in the last 10 days
— 6 If both GNSS receiver fault and Communication error with the external GNSS facility event have been recorded in the last 10 days
— 7 If all three sensor faults, have been recorded in the last 10 days ELSE it shall assign a value of 0 if no events have been recorded in the last 10 days 
                                                – sensor fault one octet as per data dictionary
                                              
RTM13Time Adjustment The VU shall generate an integer value (timeReal from Appendix 1) for data element RTM13 on the basis of the presence of Time Adjustment data as defined in Annex 1C.The VU shall assign the value of time at which the last time adjustment data event has occurred.ELSE if no ‘Time Adjustment’ event. as defined in Annex 1C is present in the VU data it shall set a value of 0 Time of the last time adjustment 
RTM14Security Breach Attempt The VU shall generate an integer value (timeReal from Appendix 1) for data element RTM14 on the basis of the presence of a Security breach attempt event as defined in Annex 1C.The VU shall set the value of the time of the latest security breach attempt event recorded by the VU.ELSE if no ‘security breach attempt’ event as defined in Annex 1C is present in the VU data it shall set a value of 0x00FF. Time of last breach attempt — Default value =0x00FF
 
RTM15Last Calibration The VU shall generate an integer value (timeReal from Appendix 1) for data element RTM15 on the basis of the presence of Last Calibration data as defined in Annex 1C.The VU shall set the value of time of the latest two calibrations (RTM15 and RTM16), which are set in VuCalibrationData defined in Appendix 1.The VU shall set the value for RTM15 to the timeReal of the latest calibration record. Time of last calibration data 
RTM16Previous Calibration The VU shall generate an integer value (timeReal from Appendix 1) for data element RTM16 of the calibration record preceding that of the last calibrationELSE if there has been no previous calibration the VU shall set the value of RTM16 to 0. Time of previous calibration data 
RTM17Date Tachograph Connected For data element RTM17 the VU shall generate an integer value (timeReal from Appendix 1).The VU shall set the value of the time of the initial installation of the VU.The VU shall extract this data from the VuCalibrationData (Appendix 1) from the vuCalibrationRecords with CalibrationPurpose equal to: ‘03’H Date tachograph connected 
RTM18Current Speed The VU shall generate an integer value for data element RTM18.The VU shall set the value for RTM16 to the last current recorded speed at the time of the latest update of the RtmData. Last current recorded speed 
RTM19Timestamp For data element RTM19 the VU shall generate an integer value (timeReal from Appendix 1).The VU shall set the value for RTM19 to the time of the latest update of the RtmData. Timestamp of currentTachographPayload record  5.4.6  DSC_42 Payload data defined previously are requested by the REDCR after initialisation phase, and consequently transmitted by the DSRC-VU in the allocated window. The command GET is used by the REDCR to retrieve data.
 DSC_43 For all DSRC exchanges, data shall be encoded using PER (Packed Encoding Rules) UNALIGNED, apart from  and  , which shall be encoded using OER (Octet Encoding Rules) defined in ISO/IEC 8825-7, Rec. ITU-T X.696.
 5.4.7  DSC_44 

Table 14.4
Initialisation — BST frame settings
Field Settings
Link Identifier Broadcast address
BeaconId As per EN 12834
Time As per EN 12834
Profile No extension, 0 or 1 to be used
MandApplications No extension, EID not present, Parameter not present, AID= 2 Freight&Fleet
NonMandApplications Not present
ProfileList No extension, number of profiles in list = 0
Fragmentation header No fragmentation
Layer 2 settings Command PDU, UI command
A practical example of the settings specified in Table 14.4, with an indication of bit encodings, is given in the following Table 14.5.


Table 14.5
Initialisation — BST frame contents example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Broadcast ID  Broadcast address
3 MAC Control Field  Command PDU
4 LLC Control field  UI command
5 Fragmentation header  No fragmentation
6 BST  Initialisation request
SEQUENCE {  
OPTION indicatorBeaconIDSEQUENCE {ManufacturerIdINTEGER (0..65535)  NonMand applications not present
  
 Manufacturer Identifier
7   
8   
IndividualIDINTEGER (0..134217727)}  27 bit ID available for manufacturer
9 
10 
11 
12 TimeINTEGER (0..4294967295)  32 bit UNIX real time
13 
14 
15 
16 ProfileINTEGER (0..127,...)  No extension. Example profile 0
17 MandApplicationsSEQUENCE (SIZE(0..127,...)) OF {  No extension, Number of mandApplications = 1
18 SEQUENCE {  
OPTION indicator  EID not present
OPTION indicator  Parameter not present
AIDDSRCApplicationEntityID } }  No extension. AID= 2 Freight&Fleet
19 ProfileListSEQUENCE (0..127,...) OF Profile }  No extension, number of profiles in list = 0
20 FCS  Frame check sequence
21 
22 Flag  End Flag DSC_45 

Table 14.6
Initialisation — Private window allocation request frame contents
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of specific DSRC-VU
3 
4 
5 
6 MAC Control field  Private window request
7 FCS  Frame check sequence
8 
9 Flag  End Flag DSC_46 
Table 14.7 provides an example of bit encoding.


Table 14.7
Initialisation — Private window allocation frame contents
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  Private window allocation
7 FCS  Frame check sequence
8 
9 Flag  End Flag DSC_47 

Table 14.8
Initialisation — VST frame settings
Field Settings
Private LID As per EN 12834
VST parameters Fill=0, then for each supported application: EID present, parameter present, AID=2, EID as generated by the OBU
Parameter No extension, Contains the RTM Context Mark
ObeConfiguration The optional ObeStatus field may be present, but shall not be used by the REDCR
Fragmentation header No fragmentation
Layer 2 settings Command PDU, UI command DSC_48 
A practical example of the settings specified in Table 14.8, with an indication of bit encodings, is given in Table 14.9.


Table 14.9
Initialisation — VST frame contents example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  Command PDU
7 LLC Control field  UI command
8 Fragmentation header  No fragmentation
9 VSTSEQUENCE {  Initialisation response
FillBIT STRING (SIZE(4))  Unused and set to 0
10 ProfileINTEGER (0..127,...)ApplicationsSEQUENCE OF {  No extension. Example profile 0
11  No extension, 1 application
12 SEQUENCE {  
OPTION indicator  EID present
OPTION indicator  Parameter present
AIDDSRCApplicationEntityID  No extension. AID= 2 Freight&Fleet
13 EID Dsrc-EID  Defined within the OBU and identifying the application instance.
14 Parameter Container {  No extension, Container Choice = 02, Octet string
15   No extension, Rtm Context Mark length = 8
16 Rtm-ContextMark::= SEQUENCE {StandardIdentifierstandardIdentifier  Object Identifier of the supported standard, part, and version. Example: ISO (1) Standard (0) TARV (15638) part9 (9) Version1 (1).First octet is 06H, which is the Object Identifier. Second octet is 06H, which is its length. Subsequent 6 octets encode the example Object Identifier.
17 
18 
19 
20 
21 
22 
23 
24 ObeConfiguration Sequence {  
OPTION indicator  ObeStatus not present
EquipmentClassINTEGER (0..32767)  
25  
26 ManufacturerIdINTEGER (0..65535)  Manufacturer identifier for the DSRC-VU as described in ISO 14816 Register
27 
28 FCS  Frame check sequence
29 
30 Flag  End Flag DCS_49 

Table 14.10
Presentation — GET request frame settings
Field Settings
Invoker Identifier (IID) Not present
Link Identifier (LID) Link address of the specific DSRC-VU
Chaining No
Element Identifier (EID) As specified in the VST. No extension
Access Credentials No
AttributeIdList No extension, 1 attribute, AttributeID = 1 (RtmData)
Fragmentation No
Layer2 settings Command PDU, Polled ACn command
Table 14.11 shows an example of reading the RTM data.


Table 14.11
Presentation — Get Request frame example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  Command PDU
7 LLC Control field  Polled ACn command, n bit
8 Fragmentation header  No fragmentation
9 Get.requestSEQUENCE {  Get request
OPTION indicator  Access Credentials not present
OPTION indicator  IID not present
OPTION indicator  AttributeIdList present
FillBIT STRING(SIZE(1))  Set to 0.
10 EID INTEGER(0..127,…)  The EID of the RTM application instance, as specified in the VST. No extension
11 AttributeIdList SEQUENCE OF {AttributeId }}  No extension, number of attributes = 1
12  AttributeId=1, RtmData. No extension
13 FCS  Frame check sequence
14 
15 Flag  End Flag DSC_50 

Table 14.12
Presentation — GET response frame settings
Field Settings
Invoker Identifier (IID) Not present
Link Identifier (LID) As per EN 12834
Chaining No
Element Identifier (EID) As specified in the VST.
Access Credentials No
Fragmentation No
Layer2 settings Response PDU, Response available and command accepted, ACn command
Table 14.13 shows an example of reading the RTM data.


Table 14.13
Presentation — Response frame contents example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  Response PDU
7 LLC Control field  Response available, ACn command n bit
8 LLC Status field  Response available and command accepted
9 Fragmentation header  No fragmentation
10 Get.responseSEQUENCE {  Get response
OPTION indicator  IID not present
OPTION indicator  Attribute List present
OPTION indicator  Return status not present
FillBIT STRING(SIZE(1))  Not used
11 EIDINTEGER(0..127,…)  Responding from the RTM applicationInstance. No extension,
12 AttributeListSEQUENCE OF {  No extension, number of attributes = 1
13 AttributesSEQUENCE {AttributeId  No extension, AttributeId=1 (RtmData)
14 AttributeValueCONTAINER {  No extension, Container Choice = 1010.
15  RtmData
16 
17 
… …
n }}}} 
n+1 FCS  Frame check sequence
n+2 
n+3 Flag  End Flag DSC_51 

Table 14.14
Termination. EVENT_REPORT Release frame contents
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  The frame contains a command LPDU
7 LLC Control field  UI command
8 Fragmentation header  No fragmentation
9 EVENT_REPORT.requestSEQUENCE {  EVENT_REPORT (Release)
OPTION indicator  Access Credentials not present
OPTION indicator  Event parameter not present
OPTION indicator  IID not present
ModeBOOLEAN  No response expected
10 EIDINTEGER (0..127,…)  No extension, EID = 0 (System)
11 EventTypeINTEGER (0..127,…) }  Event type 0 = Release
12 FCS  Frame check sequence
13 
14 Flag  End Flag DSC_52 The DSRC-VU is not expected to answer to the Release command. The communication is then closed.
 5.4.8  DSC_53 Full tests that include securing the data, need to be carried out as defined in Appendix 11 Common Security Mechanisms, by authorised persons with access to security procedures, using the normal GET command as defined above.
 DSC_54 
However, the basic DSRC communication can be tested by the command ECHO. Such tests may be required on commissioning, at periodic inspection, or otherwise to the requirement of the competent control authority or Regulation (EU) No 165/2014 (See 6 below)
 DSC_55 
— Step 1The REDCR sends a ‘beacon service table’ (BST) that includes the application identifiers (AIDs) in the service list that it supports. In the RTM applications this will simply be the service with the AID value = 2.
The DSRC-VU evaluates the received BST, and where it identifies that the BST is requesting Freight&Fleet (AID = 2), the DSRC-VU shall respond. If the REDCR does not offer AID=2, the DSRC-VU shall shut down its transaction with the REDCR.— Step 2The DSRC-VU sends a request for a private window allocation.— Step 3The REDCR sends a private window allocation.— Step 4The DSRC-VU uses the allocated private window to send its vehicle service table (VST). This VST includes a list of all the different application instantiations that this DSRC-VU supports in the framework of AID=2. The different instantiations shall be identified by means of uniquely EIDs, each associated with a parameter value indicating the instance of the application that is supported.— Step 5Next the REDCR analyses the offered VST, and either terminates the connection (RELEASE) since it is not interested in anything the VST has to offer (i.e., it is receiving a VST from a DSRC-VU that is not an RTM VU, or, if it receives an appropriate VST it starts an app instantiation.— Step 6The REDCR shall issue a command (ECHO) to the specific DSRC-VU, and allocates a private window.— Step 7The DSRC-VU uses the newly allocated private window to send an ECHO response frame.

The following tables give a practical example of an ECHO exchange session.
 DSC_56 Initialisation is performed according to 5.4.7 (DSC_44 — DSC_48) and Tables 14.4 — 14.9
 DSC_57 

Table 14.15
ACTION, ECHO request frame example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific DSRC-VU
3 
4 
5 
6 MAC Control field  Command PDU
7 LLC Control field  Polled ACn command, n bit
8 Fragmentation header  No fragmentation
9 ACTION.requestSEQUENCE {  Action request (ECHO)
OPTION indicator  Access Credentials not present
OPTION indicator  Action parameter present
OPTION indicator  IID not present
ModeBOOLEAN  Response expected
10 EIDINTEGER (0..127,…)  No extension, EID = 0 (System)
11 ActionTypeINTEGER (0..127,…)  No extension, Action type ECHO request
12 ActionParameterCONTAINER {  No extension, Container Choice = 2
13  No extension. String length = 100 octets
14   Data to be echoed
… …
113 }} 
114 FCS  Frame check sequence
115 
116 Flag  End Flag DSC_58 

Table 14.16
ACTION, ECHO response frame example
Octet # Attribute/Field Bits in octet Description
1 FLAG  Start flag
2 Private LID  Link address of the specific VU
3 
4 
5 
6 MAC Control field  Response PDU
7 LLC Control field  ACn command n bit
8 LLC status field  Response available
9 Fragmentation header  No fragmentation
10 ACTION.responseSEQUENCE {  ACTION response (ECHO)
OPTION indicator  IID not present
OPTION indicator  Response parameter present
OPTION indicator  Return status not present
FillBIT STRING (SIZE (1))  Not used
11 EIDINTEGER (0..127,…)  No extension, EID = 0 (System)
12 ResponseParameterCONTAINER {  No extension, Container Choice = 2
13  No extension. String length = 100 octets
14   Echoed data
… …
113 }} 
114 FCS  Frame check sequence
115 
116 Flag  End Flag 5.5  5.5.1  DSC_59 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.2  DSC_60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.3  DSC_61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.4  DSC_62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.5  DSC_63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.5.7  DSC_64 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DSC_65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.6  5.6.1  DSC_66 The connection between the VU and the DSRC-VU can be either by physical cable or short range wireless communication based on Bluetooth v4.0 BLE.
 DSC_67 Regardless of the choice of the physical connection and interface, the following requirements shall be satisfied:
 DSC_68  a) 

i)) using fixed cable of at least 2 meters, using a Straight DIN 41612 H11 Connector — 11 pin approved male connector from the DSRC-VU to match a similar DIN/ISO approved female connector from the VU device,
ii)) using Bluetooth Low Energy (BLE)
iii)) using a standard ISO 11898 or SAE J1939 connection
 DSC_69  b) the definition of the interfaces and connection between the VU and DSRC-VU must support the application protocol commands defined in 5.6.2. and
 DSC_70  c) the VU and DSRC-VU must support the operation of the data transfer via the connection in regard to performance and power supply.
 5.6.2  DSC_71 The application protocol between the VU Remote Communication facility and DSRC-VU is responsible for periodically transferring the remote communication data from the VU to the DSRC.
 DSC_72 

1.. Initialisation of the communication link — Request
2.. Initialisation of the communication link — Response
3.. Send Data with Identifier of the RTM application and Payload defined by RTM Data
4.. Acknowledgment of the data
5.. Termination of the communication link — Request
6.. Termination of the communication link — Response
 DSC_73 

 DSC_74 

— is used to initialize the communication link. The command is sent by the VU to the DSRC-VU. The LinkIdentifier is set by the VU and communicated to the DSRC-VU to track a specific communication link.(Note: this is to support future links and other application/modules like Weighing on board).
— is used by the DSRC-VU to provide the response of the request to initialize the communication link. The command is sent by the DSRC-VU to the VU. The command provides the result of the initialisation as answer = 1 (Success) or =0 (Failure).
 DSC_75 

— is used to by the VU to send the signed RCDTData (i.e., the remote communication Data) to the DSRC-VU. The data will be sent every 60 seconds. The DataTransactionId parameter identifies the specific transmission of data. The LinkIdentifier is also used to ensure that the appropriate link is correct.
— is sent by the DSRC-VU to provide the feedback to the VU on the reception of the data from a  command identified by the DataTransactionId parameter. The Answer parameter is 1 (Success) or =0 (Failure). If a VU receives more than three answers equal to 0 or if the VU does not receive a RCDT Data Acknowledgment for a specific previously sent RCDT- Send Data with a specific DataTransactionId, the VU will generate and record an event.
— is sent by the VU to DSRC-VU to terminate a link for a specific LinkIdentifier.
 DSC_76 

— is sent by the DSRC-VU to the VU to confirm the request of termination of the link by the VU for the specific LinkIdentifier.
 5.7  5.7.1  DSC_77 
                                          The Data
                                        shall be provided, already secure
                                          d, b
                                       y the 
                                          VUSM
                                        function to the 
                                          DSRC-VU
                                       . The 
                                          VUSM
                                        shall verify that data recorded in the 
                                          DSRC-VU
                                        has been recorded correctly. The recording and reporting of any errors in the transfer of data from the 
                                          VU
                                        to the memory of the 
                                          DSRC-VU
                                        shall be recorded with type EventFaultType and enum value set to ‘0C’H Communication error with the remote communication facility event together with the timestamp.
 DSC_78 The VU shall maintain a file identified by a unique name that is easily identifiable by inspectors for the purpose of recording ‘VU internal communication failures’.
 DSC_79 If the VUPM attempts to obtain VU data from the security module (to pass to the VU-DSRC), but fails to do so, it shall record that failure with type EventFaultType and enum value set to ‘62’H Remote Communication Facility' communication fault together with the timestamp. The failure of the communication is detected when a  message is not received for the related (i.e., with the same DataTransactionId  messages)  for more than three consecutive times.
 5.7.2  DSC_80 Communication error handling shall be consistent with the related DSRC standards, namely EN 300 674-1, EN 12253, EN 12795, EN 12834 and the appropriate parameters of EN 13372.
 5.7.2.1  DSC_81 Encryption and signature errors shall be handled as defined in Appendix 11 Common Security Mechanisms and are not present in any error messages associated with the DSRC transfer of data.
 5.7.2.2 
The DSRC medium is a dynamic wireless communication in an environment of uncertain atmospheric and interference conditions, particularly in the ‘portable REDCR’ and ‘moving vehicle’ combinations involved in this application. It is therefore necessary to ascertain the difference between a ‘read failure’ and an ‘error’ condition. In a transaction across a wireless interface, read failure is common and the consequence is usually to retry, i.e. rebroadcast the BST and reattempt the sequence, which will in most circumstances lead to a successful communication connection and transfer of data, unless the target vehicle moves out of range during the time required to retransmit. (A ‘successful’ instance of a ‘read’ may have involved several attempts and retries).

Read failure may be because the antennas were not paired properly (failure of ‘aiming’); because one of the antennas is shielded — this may be deliberate, but also can be caused by the physical presence of another vehicle; radio interference, especially from circa 5.8 GHz WIFI or other public access wireless communications, or may be caused by radar interference, or difficult atmospheric conditions (e.g. during a thunderstorm); or simply by moving out of the range of the DSRC communication. Individual instances of read failures, by their nature, cannot be recorded, simply because the communication simply did not occur.

However, if the agent of the competent control authority targets a vehicle and attempts to interrogate its DSRC-VU, but no successful transfer of data ensues, this failure could have occurred because of deliberate tampering, and therefore the agent of the competent control authority needs a means to log the failure, and alert colleagues downstream that there may be a violation. The colleagues can then stop the vehicle and carry out a physical inspection. However, as no successful communication has taken place, the DSRC-VU cannot provide data concerning the failure. Such reporting shall therefore be a function of REDCR equipment design.

‘Failure to read’ is technically different to an ‘error’. In this context an ‘error’ is the acquisition of a wrong value.

Data transferred to the DSRC-VU is supplied already secured, therefore must be verified by the supplier of the data (see 5.4).

Data subsequently transferred across the air interface is checked by cyclic redundancy checks at the communications level. If the CRC validates, then the data is correct. If the CRC does not validate, the data is retransmitted. The probability that data could successfully pass through a CRC incorrectly is statistically so highly improbable that it may be discounted.

If the CRC does not validate and there is no time to retransmit and receive the correct data, then the result will not be an error, but an instantiation of a specific type of read failure.

The only meaningful ‘failure’ data that can be recorded is that of the number of successful initiations of transactions that occur, that do not result in a successful transfer of data to the REDCR.
 DSC_82 
The only meaningful ‘error’ data that can be recorded is the number of occasions where the REDCR fails to decrypt the Data received. However, it should be noted that this will only relate to the efficiency of the REDCR software. Data may be technically decrypted, but make no semantic sense.
 DSC_83 The REDCR shall therefore record, time-stamped, the number of occasions where it has attempted but failed to decipher data received across the DSRC interface.
 6.  6.1  DSC_84 

1)) An ECHO test to validate the DSRC-REDCR >>-:-<DSRC-VU wireless communication channel.
2)) A End-to-end security test to ensure that a workshop card is able to access the encrypted and signed data content created by the VU and transmitted over the wireless communication channel.
 6.2 
This clause contains provisions specifically made to test only that the DSRC-REDCR >>-:-<DSRC-VU is functionally active.

The objective of the ECHO command is to enable workshops or type approval test facilities to test that the DSRC link is working without needing access to security credentials. The tester's equipment therefore only needs to be able to initialise a DSRC communication (sending a BST with AID=2) and then send the ECHO command, and, assuming the DSRC is working, will receive the ECHO response. See 5.4.8 for details. Assuming it receives this response correctly, the DSRC link (DSRC-REDCR >>-:-<DSRC-VU) may be validated as functioning correctly.
 6.3  DSC_85 This test is execute to validate the end-to-end security flow of data. A DSRC test reader is needed for such test. The DSRC test reader performs the same functionality and it is implemented with the same specifications of the reader used by the law enforcers, with the difference that a workshop card shall be used to authenticate the user of the DSRC test reader rather than a control card. The test can be executed after the initial activation of a Smart Tachograph or at the end of the calibration procedure. After the activation, the vehicle unit shall generate and communicate to the DSRC-VU the secured early detection data.
 DSC_86 The workshop personnel must position the DSRC test reader at a distance between 2 and 10 metres in front of the vehicle.
 DSC_87 Then the workshop personnel will insert a workshop card in the DSRC test reader to request the interrogation of the early detection data to the vehicle unit. After a successful interrogation, the workshop personnel will access the received data to ensure that it has been successfully validated for integrity and decrypted.

Appendix 15 1. 
For the purposes of this Appendix, the following definitions are used.

smart tachograph systemas defined by this Annex (chapter 1: definition bbb);first generation tachograph systemas defined by this Regulation (article 2: definition 1);second generation tachograph systemas defined by this Regulation (article 2: definition 7);introduction dateas defined by this Annex (chapter 1: definition ccc);Intelligent Dedicated Equipment (IDE)equipment used to perform data downloading, as defined in Appendix 7 of this Annex.
 2.  2.1. 
The preamble of this Annex provides an overview of the transition between the first and the second generation tachograph systems.

In addition to the provisions of this preamble:


— first generation motion sensors will not be interoperable with second generation vehicle units.
— second generation motion sensors will start to be installed in vehicles at the same time as second generation vehicle units.
— data download and calibration equipment will need to evolve, in order to support use of both generation of recording equipment and tachograph cards.
 2.2. 
It is understood that first generation tachograph cards are interoperable with first generation vehicle units in compliance with Annex IB to Regulation (EEC) No 3821/85, while second generation tachograph cards are interoperable with second generation vehicle units in compliance with Annex IC to this Regulation. In addition, the requirements below shall apply.
 MIG_001 Except as provided for in requirement MIG_004 and MIG_005, first generation tachograph cards may continue to be used in second generation vehicle units until their end of validity date. Their holders may however ask for their replacement by second generation tachograph cards as soon as they are available.
 MIG_002 Second generation vehicle units shall be able to use any valid first generation driver, control and company card inserted.
 MIG_003 This capability may be suppressed once and forever in such vehicle units by workshops, so that first generation tachograph cards cannot be accepted anymore. This may only be done after the European Commission has launched a procedure aiming to request workshops to do so, for example during each periodic inspection of tachograph.
 MIG_004 Second generation vehicle units shall only be able to use second generation workshop cards.
 MIG_005 For determining the mode of operation, second generation vehicle units shall only consider the types of the valid cards inserted, regardless of their generations.
 MIG_006 Any valid second generation tachograph card shall be able to be used in first generation vehicle units exactly the same manner as a first generation tachograph card of the same type.
 2.3. 
It is understood that first generation motion sensors are interoperable with first generation vehicle units, while second generation motion sensors are interoperable with second generation vehicle units. In addition, the requirements below shall apply.
 MIG_007 Second generation vehicle units will not be able to be paired and used with first generation motion sensors.
 MIG_008 Second generation motion sensors may be paired and used with second generation vehicle units only, or with both generations of vehicle units.
 2.4.  MIG_009 Equipment for data download may be used with one generation only of vehicle units and tachograph cards, or with both.
 2.4.1  MIG_010 Data shall be downloaded by IDE from tachograph cards of one generation inserted in their card readers, using the security mechanisms and the data download protocol of this generation, and downloaded data shall have the format defined for this generation.
 MIG_011 

— non signed EFs IC and ICC (optional),
— non signed EFs (1st generation)  and ,
— the other application data EFs (within DF Tachograph) requested by the first generation card download protocol. This information shall be secured with a digital signature, according to the first generation security mechanisms.

Such download shall not include application data EFs only present in second generation driver (and workshop) cards (application data EFs within DF Tachograph_G2).
 2.4.2  MIG_012 Data shall be downloaded from a second generation card inserted in a first generation vehicle unit using the first generation data download protocol. The card shall answer to the vehicle unit commands exactly the same manner as a first generation card and downloaded data shall have the same format as data downloaded from a first generation card.
 MIG_013 Data shall be downloaded from a first generation card inserted in a second generation vehicle unit using the data download protocol defined in Appendix 7 of this Annex. The vehicle unit shall send commands to the card exactly the same manner as a first generation vehicle unit, and downloaded data shall respect the format defined for first generation cards.
 2.4.3  MIG_014 Outside the frame of drivers' control by non EU control authorities, data shall be downloaded from second generation vehicle units using the second generation security mechanisms, and the data download protocol specified in Appendix 7 of this Annex.
 MIG_015 To allow drivers' control by non EU control authorities, it may optionally also be possible to download data from second generation vehicle units using the first generation security mechanisms. Downloaded data shall then have the same format as data downloaded from a first generation vehicle unit. This capability may be selected through commands in the menu.
 2.5.  MIG_016 Calibration equipment shall be able to perform calibration of each generation of tachograph, using the calibration protocol of this generation. Calibration equipment may be used with one generation only of tachograph, or with both.
 3.  MIG_017 Test keys and certificates shall be available to manufacturers at the latest 30 months before the introduction date.
 MIG_018 Interoperability tests shall be ready to start if requested by manufacturers at the latest 15 months before the introduction date.
 MIG_019 Official keys and certificates shall be available to manufacturers at the latest 12 months before the introduction date.
 MIG_020 Member states shall be able to issue second generation workshop cards at the latest 3 months before the introduction date.
 MIG_021 Member States shall be able to issue all types of second generation tachograph cards at the latest 1 month before the introduction date.
 4.  MIG_022 After the introduction date, Member States shall only issue second generation tachograph cards.
 MIG_023 Vehicle units/motion sensors manufacturers shall be allowed to produce first generation vehicle units/motion sensors as long as they are used in the field, so that malfunctioning components can be replaced.
 MIG_024 Vehicle units/motion sensors manufacturers shall be allowed to request and obtain type approval maintenance of first generation vehicle units/motion sensors types already type approved.

Appendix 16 1.  1.1. 
TBDTo Be DefinedVUVehicle Unit
 1.2. 
ISO16844-3 Road vehicles — Tachograph systems — Part 3: Motion sensor interface
 2.  2.1.  ADA_001 
The adaptor is only intended for those vehicles that are required to be equipped with recording equipment in compliance with this Regulation.

It shall be installed and used only in those types of vehicle defined in definition yy) ‘adaptor’ of Annex IC where it is not mechanically possible to install any other type of existing motion sensor which is otherwise compliant with the provisions of this Annex and its Appendixes 1 to 16.

The adaptor shall not be mechanically interfaced to a moving part of the vehicle, but connected to the speed/distance impulses which are generated by integrated sensors or alternative interfaces.
 ADA_002 A type approved motion sensor (according to the provisions of this Annex IC, section 8, Type approval of recording equipment and tachograph cards) shall be fitted into the adaptor housing, which shall also include a pulse converter device inducing the incoming pulses to the embedded motion sensor. The embedded motion sensor itself shall be connected to the VU, so that the interface between the VU and the adaptor shall be compliant with the requirements set out in ISO16844-3.
 2.2.  ADA_003 

— interfacing and adapting the incoming speed pulses,
— inducing the incoming pulses to the embedded motion sensor,
— all functions of the embedded motion sensor, providing secured motion data to the VU.
 2.3.  ADA_004 The adaptor shall not be security certified according to the motion sensor generic security target defined in Appendix 10 of this Annex. Security related requirements specified in section 4.4 of this Appendix shall apply instead.
 3. 
The requirements in the following Chapters indicate how the requirements of this Annex shall be understood when an adaptor is used. The related requirement numbers of Annex IC are provided between brackets.
 ADA_005 The recording equipment of any vehicle fitted with an adaptor must comply with all the provisions of this Annex, except otherwise specified in this Appendix.
 ADA_006 When an adaptor is installed, the recording equipment includes cables, the adaptor (including a motion sensor), and a VU [01].
 ADA_007 

— the ‘power supply interruption’ event shall be triggered by the VU, while not in calibration mode, in case of any interruption exceeding 200 milliseconds of the power supply of the embedded motion sensor [79]
— the ‘motion data error’ event shall be triggered by the VU in case of interruption of the normal data flow between the embedded motion sensor and the VU and/or in case of data integrity or data authentication error during data exchange between the embedded motion sensor and the VU [83]
— the ‘security breach attempt’ event shall be triggered by the VU for any other event affecting the security of the embedded motion sensor, while not in calibration mode [85]
— the ‘recording equipment’ fault shall be triggered by the VU, while not in calibration mode, for any fault of the embedded motion sensor [88]
 ADA_008 The adaptor faults detectable by the recording equipment shall be those related with the embedded motion sensor [88].
 ADA_009 The VU calibration function shall allow to automatically pair the embedded motion sensor with the VU [202, 204].
 4.  4.1.  ADA_011 The adaptor input interface shall accept frequency pulses representative of the vehicle speed and distance travelled. Electrical characteristics of the incoming pulses are: TBD by the manufacturer. Adjustments accessible to only the adaptor manufacturer, and to the approved workshop performing the adaptor installation shall allow the correct interfacing of the adaptor input to the vehicle, if applicable.
 ADA_012 The adaptor input interface shall be able, if applicable, to multiply or divide the frequency pulses of the incoming speed pulses by a fixed factor, to adapt the signal to the k factor range defined by this Annex (4 000 to 25 000 pulses/km). This fixed factor may only be programmed by the adaptor manufacturer, and the approved workshop performing the adaptor installation.
 4.2.  ADA_013 The incoming pulses, possibly adapted as specified above, shall be induced to the embedded motion sensor, so that each incoming pulse shall be detected by the motion sensor.
 4.3.  ADA_014 The embedded motion sensor shall be stimulated by the induced pulses, thus allowing it to generate motion data accurately representing the vehicle movement, as if it was mechanically interfaced to a moving part of the vehicle.
 ADA_015 The identification data of the embedded motion sensor shall be used by the VU to identify the adaptor [95].
 ADA_016 The installation data stored in the embedded motion sensor shall be considered to represent the adaptor installation data [122].
 4.4.  ADA_017 The adaptor housing shall be designed so that it cannot be opened. It shall be sealed, so that physical tampering attempts can be easily detected (e.g. through visual inspection, see ADA_035). Seals shall follow the same requirements of motion sensor seals [398 to 406]
 ADA_018 It shall not be possible to remove the embedded motion sensor from the adaptor without breaking the seal(s) of the adaptor housing, or breaking the seal between the sensor and the adaptor housing (see ADA_034).
 ADA_019 The adaptor shall ensure that motion data may only been processed and derived from the adaptor input.
 4.5.  ADA_020 The adaptor shall be fully operational in the temperature range defined by the manufacturer.
 ADA_021 The adaptor shall be fully operational in the humidity range 10 % to 90 % [214].
 ADA_022 The adaptor shall be protected against over-voltage, inversion of its power supply polarity, and short circuits [216].
 ADA_023 

— react to a magnetic field disturbing vehicle motion detection. In such circumstances, the vehicle unit will record and store a sensor fault [88] or,
— have a sensing element that is protected from, or immune to, magnetic fields [217].
 ADA_024 The adaptor shall conform to international regulation UN ECE R10, related to electromagnetic compatibility, and shall be protected against electrostatic discharges and transients [218].
 4.6.  ADA_025 The adaptor shall meet the protection grade (TBD by the manufacturer, depending on the installation position) [220, 221].
 ADA_026 The colour of the adaptor housing shall be yellow.
 4.7.  ADA_027 

— name and address of the manufacturer of the adaptor,
— manufacturer's part number and year of manufacture of the adaptor,
— approval mark of the adaptor type or of the recording equipment type including the adaptor,
— the date on which the adaptor has been installed,
— the vehicle identification number of the vehicle on which it has been installed.
 ADA_028 

— name of the manufacturer of the embedded motion sensor,
— manufacturer's part number and year of manufacture of the embedded motion sensor,
— approval mark for the embedded motion sensor.
 5.  5.1.  ADA_029 Adaptors to be installed in vehicles shall only be installed by vehicle manufacturers, or by approved workshops, authorised to install, activate and calibrate digital and smart tachographs.
 ADA_030 Such approved workshop installing the adaptor shall adjust the input interface and select the division ratio of the input signal (if applicable).
 ADA_031 Such approved workshop installing the adaptor shall seal the adaptor housing.
 ADA_032 The adaptor shall be fitted as close as possible to that part of the vehicle which provides its incoming pulses.
 ADA_033 The cables for providing the adaptor power supply shall be red (positive supply) and black (ground).
 5.2.  ADA_034 

— the adaptor housing shall be sealed (see ADA_017),
— the housing of the embedded sensor shall be sealed to the adaptor housing, unless it is not possible to remove the sensor from the adaptor housing without breaking the seal(s) of the adaptor housing (see ADA_018),
— the adaptor housing shall be sealed to the vehicle,
— the connection between the adaptor and the equipment which provides its incoming pulses shall be sealed on both ends (to the extent of what is reasonably possible).
 6.  6.1.  ADA_035 

— that the adaptor carries the appropriate type approval markings,
— that the seals on the adaptor and its connections are intact,
— that the adaptor is installed as indicated on the installation plaque,
— that the adaptor is installed as specified by the adapter and/or vehicle manufacturer,
— that mounting an adaptor is authorised for the inspected vehicle.
 ADA_036 These inspections shall include a calibration and a replacement of all seals, whatever their state.
 7.  7.1.  ADA_037 Recording equipment shall be submitted for type approval complete, with the adaptor [425].
 ADA_038 Any adaptor may be submitted for its own type approval, or for type approval as a component of a recording equipment.
 ADA_039 Such type approval shall include functional tests involving the adaptor. Positive results to each of these tests are stated by an appropriate certificate [426].
 7.2.  ADA_040 
No Test Description Related requirements
1. Administrative examination
1.1 Documentation Correctness of documentation of the adaptor 
2. Visual inspection
2.1. Compliance of the adaptor with documentation 
2.2. Identification / markings of the adaptor ADA_027, ADA_028
2.3 Materials of the adaptor [219] to [223]ADA_026
2.4. Sealing ADA_017, ADA_018, ADA_034
3. Functional tests
3.1 Inducing the speed pulses to the embedded motion sensor ADA_013
3.2 Interfacing and adapting incoming speed pulses ADA_011, ADA_012
3.3 Motion measurement accuracy [30] to [35], [217]
4. Environmental tests
4.1 Manufacturer test results Results of manufacturer environment tests. ADA_020, ADA_021, ADA_022, ADA_024
5. EMC
5.1 radiated emissions and susceptibility Verify compliance with Directive 2006/28/EC ADA_024
5.2 Manufacturer test results Results of manufacturer environment tests. ADA_024
ANNEX II
I.  1. 

((a)) a rectangle, within which shall be placed the letter ‘e’ followed by a distinguishing number or letter for the country which has issued the approval in accordance with the following conventional signs:

Belgium 6,
Bulgaria 34,
Czech Republic 8,
Denmark 18,
Germany 1,
Estonia 29,
Ireland 24,
Greece 23,
Spain 9,
France 2,
Croatia 25,
Italy 3,
Cyprus CY,
Latvia 32,
Lithuania 36,
Luxembourg 13,
Hungary 7,
Malta MT,
Netherlands 4,
Austria 12,
Poland 20,
Portugal 21,
Romania 19,
Slovenia 26,
Slovakia 27,
Finland 17,
Sweden 5,
United Kingdom 11,and
((b)) an approval number corresponding to the number of the approval certificate drawn up for the prototype of the recording equipment or the record sheet or the tachograph card, placed at any point within the immediate proximity of that rectangle.
 2. The approval mark shall be shown on the descriptive plaque of each set of equipment and on each record sheet and on each tachograph card. It must be indelible and must always remain clearly legible.
 3. 


II. 
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.

Name of competent administration …

Notification concerning:


— approval of a type of recording equipment
— withdrawal of approval of a type of recording equipment
— approval of a model record sheet
— withdrawal of approval of a model record sheet

Approval No:

….


1.. Trade mark or name …
2.. Name of type or model …
3.. Name of manufacturer …
4.. Address of manufacturer …
5.. Submitted for approval on …
6.. Tested at …
7.. Date and number of the test(s) …
8.. Date of approval …
9.. Date of withdrawal of approval …
10.. Type or types of recording equipment in which sheet is designed to be used
11.. Place …
12.. Date …
13.. Descriptive documents annexed …
14.. Remarks (including the position of seals if applicable)

(Signature)

III. 
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.

Name of competent administration …

Notification concerning:
 □ approval of:
 □ withdrawal of approval of:


□ recording equipment model
□ recording equipment component
□ a driver's card
□ a workshop card
□ a company card
□ a controller's card

Approval No:

….


1.. Manufacturing brand or trademark …
2.. Name of model …
3.. Name of manufacturer …
4.. Address of manufacturer …
5.. Submitted for approval on …
6.. Laboratory(-ies) …
7.. Date and number of test report …
8.. Date of approval …
9.. Date of withdrawal of approval …
10.. Model of recording equipment(s) with which the component is designed to be used
11.. Place …
12.. Date …
13.. Descriptive documents annexed …
14.. Remarks (including the position of seals if applicable)

(Signature)

IV. 
A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.

Name of competent administration …

Notification concerning:
 □ approval of:
 □ withdrawal of approval of:


□ recording equipment model
□ recording equipment component
□ a driver's card
□ a workshop card
□ a company card
□ a controller's card

Approval No:

….


1.. Manufacturing brand or trademark …
2.. Name of model …
3.. Name of manufacturer …
4.. Address of manufacturer …
5.. Submitted for approval on …
6.. 
((a)) Test laboratory for functional certification …
((b)) Test laboratory for security certification …
((c)) Test laboratory for interoperability certification …
7.. 
((a)) Date and number of functional certificate …
((b)) Date and number of security certificate …
((c)) Date and number of interoperability certificate …
8.. Date of approval …
9.. Date of withdrawal of approval …
10.. Model of recording equipment(s) with which the component is designed to be used
11.. Place …
12.. Date …
13.. Descriptive documents annexed …
14.. Remarks (including the position of seals if applicable)

(Signature)
