
Article 1 

1. The product group ‘sanitary tapware’ shall comprise: household taps, showerheads and showers which are mainly used to derive water for personal hygiene, cleaning, cooking and drinking, including when they are marketed for non-domestic use.
2. The following products shall be excluded from the product group ‘sanitary tapware’:
(a) bathtub taps;
(b) double lever/handle showers;
(c) non-domestic special purpose sanitary tapware.
Article 2 
For the purpose of this Decision, the following definitions shall apply:

((1)) ‘tap’ means a directly or indirectly, mechanically and/or automatically operated valve from which water is drawn;
((2)) ‘showerhead’ means:

((a)) a fixed overhead or side shower outlet, body jet shower outlet or similar device which may be adjustable, and which directs water from a supply system onto the user; or
((b)) a moveable hand held shower outlet which is connected to a tap with a shower hose and can be hung directly on the tap or on the wall with the aid of an appropriate support;
((3)) ‘shower’ means a combination of showerhead and interrelated control valves and/or devices packaged and sold as a kit;
((4)) ‘double lever/handle shower’ means a shower equipped with separate levers or handles for the control of the supply of cold and hot water;
((5)) ‘electric shower’ means a shower equipped with a device to locally heat water for the shower using electrical power;
((6)) ‘non-domestic special purpose sanitary tapware’ means sanitary tapware which requires unrestricted water flow in order to fulfil the intended non-domestic function;
((7)) ‘water flow limiting device’ means a technical device limiting water flow to a given volume and allowing a higher water flow only where activated by the user for a chosen period of time within a single use;
((8)) ‘maximum available water flow rate’ means the highest available water flow rate from the system or individual fitting;
((9)) ‘lowest maximum available water flow rate’ means the lowest water flow rate from the system or individual fitting available at full opening of the valve;
((10)) ‘security technical feature’ means a device forming part of a sensor controlled sanitary tapware which is used to prevent continuous water flow by stopping the water supply after pre-set time even if there is a person or an object present within the sensor range.
Article 3 
The criteria for awarding the EU Ecolabel under Regulation (EC) No 66/2010, for a product falling within the product group ‘sanitary tapware’ defined in Article 1 of this Decision, as well as the related assessment and verification requirements are set out in the Annex to this Decision.
Article 4 
The criteria and the related assessment requirements set out in the Annex shall be valid for four years from the date of adoption of this Decision.
Article 5 
For administrative purposes, the code number assigned to the product group ‘sanitary tapware’ shall be ‘40’.
Article 6 
This Decision is addressed to the Member States.
ANNEX
Criteria for awarding the EU Ecolabel to sanitary tapware:

1.. Water consumption and related energy saving
2.. Materials in contact with drinking water
3.. Excluded or limited substances and mixtures
4.. Product quality and longevity
5.. Packaging
6.. User information
7.. Information appearing on the EU Ecolabel
The specific assessment and verification requirements are indicated within each criterion.
Where the applicant is required to provide declarations, documentation, analyses, test reports, or other evidence to show compliance with the criteria, these may originate from the applicant or his supplier or both.
Where possible, the testing shall be performed by laboratories that meet the general requirements of European Standard EN ISO 17025 or equivalent.
Where appropriate, test methods other than those indicated for each criterion may be used if the competent body assessing the application accepts their equivalence.
As pre-requisite, the product must meet all respective legal requirements of the country (countries) in which the product is intended to be placed on the market. The applicant shall declare the product’s compliance with this requirement.

Criterion 1.  (a) 
The maximum available water flow rates of the sanitary tapware, independent of the water pressure, shall not exceed the values presented in Table 1.


Product sub-group Water flow rate[l/min]
Kitchen taps without flow limiting device 6,0
with flow limiting device 8,0
Basin taps without flow limiting device 6,0
with flow limiting device 8,0
Showerheads and showers 8,0



Assessment and verification: the applicant shall declare the product’s compliance with the requirement and specify the maximum water flow rate (in l/min) of the product submitted for the labelling procedure together with results of tests conducted in accordance with testing procedure indicated in respective EN standards for the given kind of product (see Table 2). The testing shall be conducted at a pressure of 1,5, 3,0 and 4,5 bar (± 0,2 bar) for products claimed to be suitable for high pressure installations (typically 1,0 to 5,0 bar) or at pressure of 0,2, 0,3 and 0,5 bar (± 0,02 bar) for products claimed to be suitable for low pressure installations (typically 0,1 to 0,5 bar). A mean value of three measurements shall not exceed the maximum flow rate values indicated in Table 1. For pillar taps and divided spout outlet kitchen taps, the flow rate shall be the summation of the two flows, i.e. the total flow to basin or sink from the hot and cold water tapware. Additionally, for products with an option of economy setting (i.e. flow limiting device), a description of the device applied (i.e. its main technical parameters and installation, setting and use instructions) shall be submitted.


Number Title
EN 200 Sanitary tapware. Single taps and combination of taps for water supply systems of type 1 and type 2 – General technical specification
EN 816 Sanitary tapware. Automatic shut-off valves (PN10)
EN 817 Sanitary tapware. Mechanical mixing valves (PN10) – General technical specifications
EN 1111 Sanitary tapware. Thermostatic mixing valves (PN10) – General technical specification
EN 1112 Sanitary tapware. Shower outlets for sanitary tapware for water supply systems type 1 and type 2 – General technical specification
EN 1286 Sanitary tapware. Low pressure mechanical mixing valves. General technical specification
EN 1287 Sanitary tapware. Low pressure thermostatic mixing valves. General technical specifications
EN 15091 Sanitary tapware. Electronic opening and closing sanitary tapware
EN 248 Sanitary tapware. General specification for electrodeposited coatings of Ni-Cr
EN60335-1 Household and Similar Electrical Appliances
EN60335-2-35 Household and Similar Electrical Appliances, Safety, Particular Requirements for Instantaneous Water heaters
 (b) 
The lowest maximum available water flow rates of the sanitary tapware, independent of the water pressure, shall not be lower than the values given in Table 3:


Product sub-group Water flow rate[l/min]
Kitchen taps 2,0
Basin taps 2,0
Showers and showerheads 4,5
Electric showers and low pressure showers 3,0


Assessment and verification: the applicant shall declare the product’s compliance with the requirement and specify the lowest maximum available water flow rate of the product submitted for the labelling procedure together with the results of tests conducted in accordance with the testing procedure indicated in respective EN standards for the given kind of product (see Table 2). 1,5, 3,0 and 4,5 bar (± 0,2 bar) for products claimed to be suitable for high pressure installations (typically 1,0 to 5,0 bar) or at pressure of 0,2, 0,3 and 0,5 bar (± 0,02 bar) for products claimed to be suitable for low pressure installations (typically 0,1 to 0,5 bar). A mean value of three measurements shall not be lower than the flow rate value given in Table 3. For pillar taps and divided spout outlet kitchen taps, the flow rate shall be the summation of the two flows, i.e. the total flow to basin or sink from the hot and cold water tapware.
 (c) 
Sanitary tapware shall be equipped with an advanced device or technical solution which allows for the management of temperature and/or hot water by the end-user, for example by limiting the water temperature or the supply of hot water, or by thermostatic adjustment.

The solution shall be specified to provide the user with accurate control over the temperature of the water from the tap or shower, independent of the heating system to which it is connected. Possible solutions may include, for example, a hot water barrier, a cold water supply in middle position and/or a thermostatic mixing valve.

Sanitary tapware designed to be fitted to a water supply that is already temperature controlled and showerheads shall be exempted from this criterion.

Assessment and verification: in the application submitted to the competent body, the applicant shall declare that the product complies with the requirement and provide documentation describing the technology or device applied in the product. Where the water supply is already temperature controlled, the applicant shall explain the specific technical property that makes the sanitary tapware suited for fitting to this form of system.
 (d) 
This criterion applies to sanitary tapware which is sold or marketed together with time control devices (i.e. devices which stop water flow after a certain time if they are not used, for example sensors which stop the water flow when a user leaves the sensor range, or after a set time period of use, for example, time limiters, which stop the water flow when the maximum flow time is reached).

For sanitary tapware equipped with time limiters, the pre-set maximum flow period should not exceed 15 seconds for taps and 35 seconds for showers. Nevertheless, the product shall be designed to allow the installer to adjust the flow time in accordance with the intended product’s application.

For sanitary tapware equipped with a sensor, shut off delay time after usage shall not exceed 1 second for taps and 3 seconds for showers. Furthermore, the sanitary tapware equipped with a sensor shall have an in-built ‘security technical feature’ with a pre-set shut-off time of maximum 2 minutes to prevent an accident or continuous water flow from taps or showers when not in use.

Assessment and verification: the product or system shall be tested at the pressure range stipulated (3,0 bar (± 0,2 bar) for high pressure valves or 0,5 bar (± 0,02 bar) for low pressure valves) to verify that the time control shuts off within a 10 % tolerance of that specified by the applicant. The applicant shall declare that the product complies with the requirement and specify the type of solution used within its technical parameters (a pre-set water flow time for time limiters, the shut-off delay time after usage for sensors), and provide the results of a test conducted in accordance with the standard EN 15091 for electronic opening and closing sanitary tapware or EN 816 for automatic shut-off valves to the competent body as part of the application.

Criterion 2. 
Materials used in products coming into contact with drinking water, or impurities associated with them, shall not release into water intended for human consumption any compounds in concentrations higher than necessary for the purpose of their use and shall not either directly or indirectly reduce the protection of human health. They shall not cause any deterioration in the quality of water intended for human consumption with regard to appearance, odour or taste. Within the recommended limits for correct operation (i.e. conditions of use as laid down in the respective EN standards indicated in Table 2), the materials shall not undergo any change which would impair the performance of the product. Materials without adequate resistance to corrosion shall be adequately protected so that they do not present a health risk.

Assessment and verification: the applicant shall declare that the product complies with the requirement and submit relevant documentation or test results, as indicated below:

Metallic materials in contact with drinking water used in sanitary tapware shall be listed in the positive list ‘Acceptance of Metallic Materials for Products in Contact with Drinking Water’ as given in the Appendix. The applicant shall submit a declaration of compliance with this requirement. If the metallic materials are not included in this positive list, results of test conducted in accordance with the approach for ‘Adding Materials to the Composition List within a Category of Materials’, as described in the Appendix, and using the EN 15664-1 standard, shall be submitted. Alternatively, if obligatory national regulations are in place in the Member State where the product will be placed on the market, a certificate of approval of these metallic materials and/or product issued by national authorities or responsible laboratories shall be submitted.

Organic materials in contact with drinking water shall be tested in accordance with the respective requirements of the Member State where the product will be placed on the market. A certificate or, if appropriate, test results issued by national authorities or responsible laboratories shall be submitted.

Additionally, if required by the national regulations or the Member State where the product is placed on the market, test results for enhancement of microbial growth and assessment of odour and flavour assessment of water shall be submitted.

Criterion 3.  (a) 
According to the Article 6(6) of Regulation (EC) No 66/2010 on the EU Ecolabel, the product or any article of it shall not contain substances meeting criteria for classification with the hazard statements or risk phrases specified below in accordance with Regulation (EC) No 1272/2008 of the European Parliament and of the Council or Council Directive 67/548/EEC nor shall it contain substances referred to in Article 57 of Regulation (EC) No 1907/2006 of the European Parliament and of the Council. The risk phrases below generally refer to substances. However, if information on substances cannot be obtained, the classification rules for mixtures apply.


Hazard Statement Risk Phrase
H300 Fatal if swallowed R28
H301 Toxic if swallowed R25
H304 May be fatal if swallowed and enters airways R65
H310 Fatal in contact with skin R27
H311 Toxic in contact with skin R24
H330 Fatal if inhaled R23/26
H331 Toxic if inhaled R23
H340 May cause genetic defects R46
H341 Suspected of causing genetic defects R68
H350 May cause cancer R45
H350i May cause cancer by inhalation R49
H351 Suspected of causing cancer R40
H360F May damage fertility R60
H360D May damage the unborn child R61
H360FD May damage fertility. May damage the unborn child R60/61/60-61
H360Fd May damage fertility. Suspected of damaging the unborn child R60/63
H360Df May damage the unborn child. Suspected of damaging fertility R61/62
H361f Suspected of damaging fertility R62
H361d Suspected of damaging the unborn child R63
H361fd Suspected of damaging fertility. Suspected of damaging the unborn child. R62-63
H362 May cause harm to breast fed children R64
H370 Causes damage to organs R39/23/24/25/26/27/28
H371 May cause damage to organs R68/20/21/22
H372 Causes damage to organs through prolonged or repeated exposure R48/25/24/23
H373 May cause damage to organs through prolonged or repeated exposure R48/20/21/22
H400 Very toxic to aquatic life R50
H410 Very toxic to aquatic life with long-lasting effects R50-53
H411 Toxic to aquatic life with long-lasting effects R51-53
H412 Harmful to aquatic life with long-lasting effects R52-53
H413 May cause long-lasting harmful effects to aquatic life R53
EUH059 Hazardous to the ozone layer R59
EUH029 Contact with water liberates toxic gas R29
EUH031 Contact with acids liberates toxic gas R31
EUH032 Contact with acids liberates very toxic gas R32
EUH070 Toxic by eye contact R39-41





Substances or mixtures which change their properties through processing (e.g. become no longer bioavailable, or undergo chemical modification in a way that removes the previously identified hazard) are exempted) from the above requirement.

Concentration limits for substances or mixtures which may be or have been assigned the hazard statements or risk phrase listed above, meeting the criteria for classification in the hazard classes or categories, and for substances meeting the criteria of Article 57 (a), (b) or (c) of Regulation (EC) No 1907/2006, shall not exceed the generic or specific concentration limits determined in accordance with the Article 10 of Regulation (EC) No 1272/2008. Where specific concentration limits are determined they shall prevail over the generic ones.

Concentration limits for substances meeting criteria of Article 57 (d), (e) or (f) of Regulation (EC) No 1907/2006 shall not exceed 0,1 % weight by weight.

The final product must not be labelled according to the hazard statements above.

The following substances/components are specifically derogated from this requirement:


Nickel in stainless steel of all types All hazard statements and risk phrases
Articles and homogenous parts of sanitary tapware in contact with drinking water made of alloys, which fall under Article 23 (d) of Regulation (EC) No 1272/2008 and are listed in Part B of the ‘Acceptance of metallic materials used for products in contact with drinking water’ – Common Approach’ or fulfil the requirements to be added to this list as indicated in the Appendix. All hazard statements and risk phrases
Nickel in protective coating layer, if the release of nickel from nickel layers or a coating containing nickel on inner surfaces of products which are intended to come into contact with drinking water tested in accordance with EN 16058 standard does not exceed 10 μg/l. All hazard statements and risk phrases
Electronic components of sanitary tapware, which fulfil the requirements of Directive 2011/65/EU All hazard statements and risk phrases




Assessment and verification: for each article or any homogenous part of the applicant shall provide a declaration of compliance with this criterion, together with related documentation, such as declarations of compliance signed by their suppliers, on the non-classification of the substances or materials with any of the hazard classes associated to the hazard statements referred to in the above list in accordance with Regulation (EC) No 1272/2008, as far as this can be determined, as a minimum, from the information meeting the requirements listed in Annex VII of Regulation (EC) No 1907/2006. This declaration shall be supported by summarized information on the relevant characteristics associated to the hazard statements referred to in the above list, to the level of detail specified in section 10, 11 and 12 of Annex II of Regulation (EC) No 1907/2006 (Requirements for the Compilation of Safety Data Sheets).

Information on intrinsic properties of substances may be generated by means other than tests, for instance through the use of alternative methods such as in vitro methods, by quantitative structure activity models or by the use of grouping or read-across in accordance with Annex XI of Regulation (EC) No 1907/2006. The sharing of relevant data is strongly encouraged.

The information provided shall relate to the forms or physical states of the substance or mixtures as used in the final product.

For substances listed in Annexes IV and V of REACH, exempted from registration obligations under Article 2(7)(a) and (b) of Regulation (EC) No 1907/2006 REACH, a declaration to this effect will suffice to comply with the requirements set out above.
 (b) 
No derogation from the exclusion in Article 6(6) of the Regulation (EC) No 66/2010 shall be given concerning substances identified as substances of very high concern and included in the list foreseen in Article 59 of Regulation (EC) No 1907/2006, present in mixtures, in an article or in any homogeneous part of a complex article in concentrations > 0,1 %. Specific concentration limits determined in accordance with Article 10 of Regulation (EC) No 1272/2008 shall apply in cases where the concentration is lower than 0,1 %.

Assessment and verification: The list of substances identified as substances of very high concern and included in the candidate list in accordance with Article 59 of Regulation (EC) No 1907/2006 can be found on the ECHA website.

Reference to the list shall be made on the date of application. The applicant shall provide a declaration of compliance with this criterion, together with related documentation, such as declarations of compliance signed by the material suppliers and copies of relevant Safety Data Sheets for substances or mixtures in accordance with Annex II to Regulation (EC) No 1907/2006 for substances or mixtures. Concentration limits shall be specified in the Safety Data Sheets in accordance with Article 31 of Regulation (EC) No 1907/2006 for substances and mixtures.

Criterion 4.  (a) 
The product shall comply with the general requirements of the respective EN standards listed in Table 2 or with the corresponding mandatory national legal regulations. The requirement regarding water flow rates is excluded from this criterion.

Where applicable, cleaning of the product elements, which may be necessary under normal use conditions, shall be possible with use of simple tools or agents.
 (b) 
A sanitary product which has a metallic Ni-Cr coating (regardless of the nature of the substrate material) shall comply with the standard EN 248.
 (c) 
The product shall be designed in such a way that its exchangeable components can be replaced easily by the end-user or a professional service engineer, as appropriate. Information about which elements can be replaced shall be clearly indicated in the information sheet attached to the product. The applicant shall also provide clear instructions to enable the end-user or trained experts, as appropriate, to undertake basic repairs.

The applicant shall further ensure that spare parts are available for at least seven years from the end of production.
 (d) 
The applicant shall give a warranty for repair or replacement of minimum four years.

Assessment and verification: the applicant shall declare that the product complies with these requirements and provide samples of the product information sheet and warranty terms to the competent body as part of the application.

With regard to points (a) and (b) the applicant shall additionally provide the competent body with the results of tests conducted in accordance with the standards listed in Table 2 as regards point (a) and the standard EN 248 as regards point (b) as part of the application.

Criterion 5. 
Packaging shall meet the following requirements:


((a)) all packaging components shall be easily separable by hand into individual materials in order to facilitate recycling,
((b)) where used, cardboard packaging shall consist of at least 80 % recycled material.

Assessment and verification: the applicant shall declare that the product complies with the requirement and provide the competent body with a sample(s) of the packaging as part of the application.

Criterion 6. 
The product shall be accompanied by relevant user information which provides advice on the product’s proper and environmentally friendly use as well as its maintenance. It shall bear the following information in print (on the packaging and/or on documentation accompanying the product) and/or in electronic format:


((a)) information that the main environmental impact is related to the use phase of the product, i.e. to consumption of water and related energy for water heating and advice on how rational use can minimise the environmental impact,
((b)) information that the product has been awarded the EU Ecolabel, together with a brief, specific explanation as to what this means in addition to the general information provided alongside the EU Ecolabel logo,
((c)) the maximum flow rate in l/min (tested as indicated in Criterion 1(a)),
((d)) installation instructions, including information on the specific operating pressures that the product is suitable for,
((e)) advice concerning the issue of water stagnation and a related warning against drinking tap water after a longer stagnation time (applicable for taps), such as for example ‘To avoid the wastage of drinking water, use stagnation water (e.g. such as water used in the morning or after holidays) to for example, flush toilets, take a shower or water gardens’,
((f)) recommendations on the proper use and maintenance (including cleaning and decalcification) of the product, mentioning all relevant instructions, particularly:

((i)) advice on maintenance and use of products,
((ii)) information about which spare parts can be replaced,
((iii)) instructions concerning the replacement of washers if taps drip water,
((iv)) advice on cleaning sanitary tapware with appropriate materials in order to prevent damage to their internal and external surfaces.
((v)) advice on regular and proper service of aerators.

For sanitary tapware (except showerheads) which is not equipped with time control devices, the following text shall be visibly reproduced on the packaging of the product:

'This EU Ecolabel product is intended for domestic use. It is not intended for use in a non-domestic environment for multiple and frequent use (e.g. public facilities in schools, offices, hospitals, swimming-pools)'.

For sanitary tapware which is equipped with time control devices, the following text shall be visibly reproduced on the packaging of the product:

'This EU Ecolabel product is particularly intended for use in non-domestic environment for multiple and frequent use (e.g. public facilities in schools, offices, hospitals, swimming-pools)'.

For ‘restricted flow showerheads’ information should be placed on the product sheet regarding the need of checking the compatibility when used with electric shower, e.g. ‘please check that this restricted flow showerhead is compatible with your existing shower system in case you plan to use it with an electric shower’.

Assessment and verification: the applicant shall declare that the product complies with the requirement and provide the competent body with a sample or samples of the user information and/or a link to a manufacturer’s website containing this information as part of the application.

Criterion 7. 
The optional label with text box shall contain the following text:


— Improved water efficiency
— Increased energy saving potential
— With this certified product you save water, energy and money.

The guidelines for the use of the optional label with the text box can be found in the ‘Guidelines for the use of the EU Ecolabel logo’ on the website:

http://ec.europa.eu/environment/ecolabel/promo/pdf/logo%20guidelines.pdf

Assessment and verification: the applicant shall provide a sample of the label, together with a declaration of compliance with this criterion.

Appendix
The following information is based on the report of ‘ACCEPTANCE OF METALLIC MATERIALS USED FOR PRODUCTS IN CONTACT WITH DRINKING WATER. Common Approach. Part A – Procedure for the acceptance and Part B – Common Composition List’ accessible via http://www.umweltbundesamt.de/wasser-e/themen/trinkwasser/4ms-initiative.htm.
Excerpt 1 of the ‘ACCEPTANCE OF METALLIC MATERIALS USED FOR PRODUCTS IN CONTACT WITH DRINKING WATER. Common Approach. Part A. Procedure for the acceptance’ presented in chapter 2.

1. 
Metallic materials used for PDW must be listed on the Composition List.
 1.1. 
The primary responsibility for assessment of materials will remain at the national level making use of established processes and the expert resources available there. However, the interpretation of test results and the application of acceptance criteria described below is complex. For this reason a Committee of Experts should advice in the decision-making process.

The Committee of Experts should have the following expertise:


— Competent knowledge of corrosion and metal release
— Competence on toxicology and evaluation of drinking water quality related to human health aspects
— Understanding of the ways in which metallic materials and products are used in drinking water treatment and supply

The 4 Member States group agreed on a common procedure to accept materials on a common Composition List. This procedure is described in Part B of this document.
 1.2. 
The Composition List contains different categories of metallic materials.

A Category is defined as:

a group of materials with the same characteristics in respect of their field of application, behaviour in contact with drinking water and restrictions with regard to water composition and/or surface area.

The Composition List contains the categories’ range of compositions.

Each category has one reference material.

A Reference Material is defined as:

a material falling within a category for which the characteristics of metal release into drinking water are known and reproducible, the composition is strictly controlled and the elements of interest will be at or near the upper limit of acceptability. Possible effects of some constituents to inhibit the metal release have to be taken into account.

Under each category commercially available metallic materials accepted for use in PDW will be listed. The materials may only be used for certain products due to the restrictions with respect to the surface area (Table 1).


Product Group Examples of products or parts of products Assumed contact surface‘a’
A Pipes in buildings installationUncoated pipelines in water supply systems 100 %
B FittingsAncillariesParts of pumps in buildings installationsParts of valves in buildings installations 10 %
C Moving parts in water meterParts of pumps in water supply systemsParts of valves in water supply systems 1 %
 — 
For pipes in a buildings installation the same material can be used for all diameters. A single material can contribute to nearly 100 % of the surface in contact with water e.g. copper, galvanised steel or stainless steel. The evaluation of the conditions for safe use must assume the maximum possible percentage. The acceptance of a composition for the use as pipes includes the acceptance for all uses (e.g. fittings, components, etc.).

This group also includes uncoated metallic pipelines in water supply systems and water treatment processes.
 — 
Fittings or ancillaries can be produced from one material or from slightly different materials throughout the buildings installation. The most common are made from copper alloys that contain lead. Due to their potential to release lead to water there is a need to restrict the total surface contact of products made from these alloys. For assessments of materials for these products a contribution of 10 % water contact surface area is assumed.

This group also includes metallic parts of pumps and valves used in buildings installations.
 — 
For technical reasons, there might be a need to produce small parts from compositions not accepted for the Product Group B, fittings and ancillaries. Other compositions with higher release rates may be accepted in these devices as long as their use will not significantly increase the total contamination of drinking water. The use of such compositions should be restricted to parts that do not exceed 1 % of the total surface in contact with drinking water; for example, the body of a water meter would need to be produced from an accepted composition for Product Group B but a moving part may be produced from a material listed for Product Group C.

This group also includes metallic parts of pumps and valves used in water supply systems and water treatment processes.
 1.3. 
Acceptance of metallic materials is based on results of long term tests on a rig test according to EN 15664-1. The minimum test period is six months and which can be extended. Additional requirements for the testing according to EN 15664-1 are described in 1.4 and 1.5.

Acceptance of a reference material for a category requires acceptance of results from the EN 15664-1 test carried out with different waters (see EN 15664-2) representing the normal range of compositions of drinking waters in the EU.

To add a material in a category, a comparative test against the reference material is required using EN 15664-1. For comparative testing it is sufficient to use a local drinking water, provided that the water is suitably corrosive (see EN 15664-2).

The following information shall be provided:


— Test reports according to EN 15664-1
— Test reports for the composition of the test specimen
— For each composition, information on the boundaries for major alloying constituent elements and maximum values for impurities. Such boundaries will be tighter for Reference Materials than for commercial alloys
— Existing applicable European standard(s) for the material
— The material characteristics
— Products to be manufactured from the material and their uses (a-factor)
— The production process
— Other information considered appropriate in support of the assessment
 1.4. 
For the testing of a material according to EN 15664-1 the test specimens have to be of a certain composition.

All elements exceeding 0,02 % could be of relevance and have to be declared for the composition of the material to be listed. For impurities below 0,02 % it is the responsibility of the producer of the alloys/materials to guarantee that no release occurs with the potential to cause negative health impacts.

The composition of the test specimens shall be as follows:
 1.4.1. 
The test specimens submitted for testing a new reference material and the test specimens used as reference materials for the comparative testing have to meet the following requirements:


— Constituents and impurities have to be in the range as declared.
Note: The composition of the reference material should be accepted before testing is started. The range of composition should be very narrow and the reference material should represent a worst case material in respect of the metal release of concern for the category. 1.4.2. 
For the candidate materials the range of composition and its allowed impurities have to be defined. Comparative testing is possible, if the defined range of composition of the candidate material complies with the definition of an existing category of materials.

The composition of the test specimens used for testing has to be more restricted than the defined range of composition of the material. Based on the knowledge about copper alloys the composition of the test specimens has to meet the following requirements:


 Constituents:
— Cu, Zn as constituents have to be in the range as declared
— As as a constituent shall be greater than 66 % of the declared range. (e.g. if the declared range is ≤ 0,15 % then 66 % of the range (0,15 %) is 0,10 %; therefore, element content should be 0,10-0,15 %.)
— Al, Si and P shall be less than 50 % of the declared range
— For all other constituents the content shall be greater than 80 % of the declared range (e.g. if the declared range is 1,6 to 2,2 % then 80 % of the range (0,6 %) is 0,48 %; therefore, element content should be greater than 2,08 %.).
 Impurities:
— Impurities to be analysed in the contact water (see 1.5) shall be greater than 60 % of the declared maximum content

For other non-copper alloys these requirements may be different.
 1.5. 
If a new reference material is tested the contact water according to EN 15664-1 has to be analysed for all elements exceeding 0,02 % in the composition of the declared material with the exception of:


— Sn, Si and P if present as constituents
— Fe, Sn, Mn, Al, Si and P if present as impurities in the alloy

For comparative testing the analysis of contact water may be limited to certain elements specified for each category in the composition list.
 1.6. 
Table 2 proposes the acceptable contributions from metallic PDW to the overall concentrations of metals at consumers’ taps. It is based on the acceptance values for chemical and indicator parametric values in the DWD. The acceptable contributions were derived using the following principles:


— 90 % for elements for which metallic PDW constitute the only major source of contamination;
— 50 % for elements for which other sources of contamination are possible

In the case of other parameters not listed in the DWD, the following criteria have been used:


— Zinc: this element is not toxic at the concentrations encountered in water supply systems where galvanised steel pipes have been used. However, zinc can give rise to complaints about the taste and appearance of water. The proposed reference value has been set to ensure that zinc does not reduce the aesthetic acceptability of water (WHO, 2004).
— Tin, bismuth, molybdenum, titanium: these reference values are based on provisional values recommended by a toxicology expert (Fawell, 2003).
— Other metals: Advice will be sought from toxicology experts on an appropriate reference value as necessary

In order to allow time for the development of natural protective layers, it is proposed that the test procedure simulates a conditioning period of three months, in which a slight non-compliance with the reference concentration is tolerated.


Parameter Acceptable contribution from metallic PDW DWD parametric value or proposed reference value in DW(μg/l) Reference concentration ‘RC’ for Acceptance Scheme(μg/l)
Part B:Chemical parameters
Antimony 50 % 5 2,5
Arsenic 50 % 10 5
Chromium 50 % 50 25
Cadmium 50 % 5 2,5
Copper 90 % 2 000 1 800
Lead 50 % 10 5
Nickel 50 % 20 10
Selenium 50 % 10 5
Part C:Indicator parameters
Aluminium 50 % 200 100
Iron 50 % 200 100
Manganese 50 % 50 25
Others: not listed in DWD
Bismuth 90 % 10 9
Molybdenum 50 % 20 10
Tin 50 % 6 000 3 000
Titanium 50 % 15 7,5
Zinc 90 % 3 000 2 700
 1.7. 
The addition or change of range of an alloying element may move an alloy outside a Category and this change may significantly influence the metal release characteristics of the material. In this case and for an alloy representative of a Category (Reference Material) the following information shall be provided.


— The information listed in 1.3
— Where a proposed new composition is not comparable to a listed Category of materials the full test results from pipe rig testing according to EN15664-1 using at least three different drinking waters defined in EN15664-2 shall be provided.
 1.7.1. 
For the assessment of the test rig results (according to EN 15664-1) the arithmetic mean of the equivalent pipe concentrations MEPn(T) shall be considered.

For all periods of operation (T) an average of the MEPn(T) of the three test lines in one rig is calculated: MEPa(T).

The material can be accepted for a product group with the assumed contact surface a (see Table 1), if:


((I)) MEPa(T) * a ≤ RC for T = 16, 21 and 26 weeks
((II)) MEPa(Tb) ≥ MEPa(T) for {Tb, T} = {12, 16}, {16, 21} and {21, 26} weeks

are met for all tested drinking waters.

The test may be extended up to 1 year, if criterion II is not met. In this case the material is acceptable, if


((III)) MEPa(Tb) ≥ MEPa(T) for {Tb, T} = {26, 39} and {39, 52} weeks

is met for the tested drinking waters, where criterion II was not fulfilled.

The complete set of available data has to be considered. For the test rig according to EN 15664-1 these are:


— Results of individual test lines,
— 4h stagnation results and
— parameters of water composition.

If stagnation samples were analysed in addition to the requirements in EN 15664-1 this data shall also be considered for the assessment.

The Committee of Expert shall decide, whether the data available is of sufficient quality (e.g. no major difference of the three test lines, interpretation of outliers) for an assessment to be carried out and if so decide whether to accept the material based on the above mentioned criteria. Accepted materials will be added to the Composition List together with the Category as the Reference Material.
 1.8. 
Where the constituents of a candidate material for approval are shown to fall within a Category, the material can be added to the Composition List provided that a comparative test run against the respective Reference Material in a standardised rig test, EN15664-1, using one water defined in EN15664-2 shows satisfactory results.

For each material, the following information shall be provided:


— The information listed in 1.3
— Results from comparative testing using the pipe rig test EN15664-1 relative to the Category’s Reference Material
 1.8.1. 
For the assessment of the test rig results (according to EN 15664-1) the arithmetic mean of the equivalent pipe concentrations MEPn(T) shall be considered.

For all periods of operation (T) an average of the MEPn(T) of the three test lines in the rig is calculated: MEPa(T).

For the Reference Material MEPa,RM(T) of the three reference lines shall be considered.

The material can be accepted for a product group with the assumed contact surface a of the Reference Material (see Table 1), if:


((I)) MEPa(T) ≤ MEPa,RM(T) for T = 16, 21 and 26 weeks
((II)) MEPa(Tb) ≥ MEPa(T) for {Tb, T} = {12, 16}, {16, 21} and {21, 26} weeks

are met for the tested drinking water.

The test may be extended up to 1 year, if criterion II is not met. In this case the material is acceptable, if


((III)) MEPa(Tb) ≥ MEPa(T) for {Tb, T} = {26, 39} and {39, 52} weeks

is met.

The complete set of available data has to be considered. For the test rig according to EN 15664-1 these are:


— Results of individual test lines,
— 4h stagnation results and
— parameters of water composition.

If stagnation samples were analysed in addition to the requirements in EN 15664-1 this data shall also be considered for the assessment.

The Committee of Expert shall decide, whether the data available is of sufficient quality (e.g. no major difference of the three test lines, interpretation of outliers) for an assessment to be carried out, and if so decide whether to accept the materials based on the above mentioned criteria. Accepted materials will be added to the Composition List for the Category of the Reference Material used for comparative testing.

Excerpt 2 of the ‘ACCEPTANCE OF METALLIC MATERIALS USED FOR PRODUCTS IN CONTACT WITH DRINKING WATER. Common Approach. Part B – Common Composition List’ presented in chapter 2.
 1.8.1.1. 

Constituent Content (%) Impurity Maximum (%)
Copper ≥ 57,0 Antimony 0,02
Zinc Remainder Arsenic 0,02
Lead ≤ 3,5 Bismuth 0,02
Aluminium ≤ 1,0 Cadmium 0,02
Iron ≤ 0,5 Chromium 0,02
Silicon ≤ 1,0 Nickel 0,2
Tin ≤ 0,5  


Constituent Content (%) Impurity Maximum (%)
Copper 57,0 – 59,0 Antimony 0,02
Zinc Remainder Arsenic 0,02
Lead 1,9-2,1 Bismuth 0,02
  Cadmium 0,02
  Chromium 0,02
  Nickel 0,2
  Aluminium 0,2
  Iron 0,3
  Silicon 0,02
  Tin 0,3

Elements for consideration in the migration water:

Lead, nickel, copper, zinc

Addition of:

For each element: Acceptance factors in comparison to the mentioned reference material
 1.8.1.2. 

Constituent Content (%) Impurity Maximum (%)
Copper 57,0 – 60,0 Antimony 0,02
Zinc Remainder Arsenic 0,02
Lead 1,6 – 2,2 Bismuth 0,02
  Cadmium 0,02
  Chromium 0,02
  Nickel 0,1
  Aluminium 0,05
  Iron 0,3
  Silicon 0,03
  Tin 0,3

Product group B

Product group C

German Co-normative Research Report RG_CPDW_01_074

Dossier John Nuttall (March 2006)


Constituent Content (%) Impurity Maximum (%)
Copper 57,0 – 62,0 Antimony 0,02
Zinc Remainder Arsenic 0,02
Lead 2,5 – 3,5 Bismuth 0,02
  Cadmium 0,02
  Chromium 0,02
  Nickel 0,2
  Aluminium 0,05
  Iron 0,3
  Silicon 0,03
  Tin 0,3

Product group C

German Co-normative Research Report RG_CPDW_01_074

Dossier John Nuttall (March 2006)
 1.8.1.3. 

Constituent Content (%) Impurity Maximum (%)
Copper ≥ 61,0 Antimony 0,02
Zinc Remainder Bismuth 0,02
Arsenic ≤ 0,15 Cadmium 0,02
Lead ≤ 2,2 Chromium 0,02
Aluminium ≤ 1,0 Nickel 0,2
Iron ≤ 0,5  
Silicon ≤ 1,0  
Tin ≤ 0,5  


Constituent Content (%) Impurity Maximum (%)
Copper 61,0-63,0 Antimony 0,02
Zinc Remainder Bismuth 0,02
Arsenic 0,09-0,13 Cadmium 0,02
Lead 1,4-1,6 Chromium 0,02
Aluminium 0,5-0,7 Nickel 0,2
  Iron 0,12
  Silicon 0,02
  Tin 0,3

Elements for consideration in the migration water:

Lead, nickel, arsenic, copper, zinc

Based on the results of ongoing dedicated research (by industry), the alloying elements (constituents) and the impurities will be limited such, that the alloys can be used in any drinking water.

Product Group B

Product Group C

Dossier John Nuttall (March 2006)

Addition of:

For each element: Acceptance factors in comparison to the mentioned reference material
 1.8.1.4. 

Constituent Content (%) Impurity Maximum (%)
Copper Remainder Aluminium 0,01
Zinc ≤ 6,5 Antimony 0,1
Tin ≤ 13,0 Arsenic 0,03
Lead ≤ 3,0 Bismuth 0,02
Nickel ≤ 0,6 Cadmium 0,02
  Chromium 0,02
  Iron 0,3
  Silicon 0,01


Constituent Content (%) Impurity Maximum (%)
Copper Remainder Aluminium 0,01
Zinc 5,9-6,2 Antimony 0,1
Tin 3,9-4,1 Arsenic 0,03
Lead 2,8-3,0 Bismuth 0,02
Nickel 0,5-0,6 Cadmium 0,02
  Chromium 0,02
  Iron 0,3
  Silicon 0,01

Elements for consideration in the migration water:

Lead, nickel, antimony, copper, zinc, tin

Addition of:

For each element: Acceptance factors in comparison to the mentioned reference material
 1.8.1.5. 

Constituent Content (%) Impurity Maximum (%)
Copper 84,0 – 88,0 Aluminium 0,01
Zinc 4,0 – 6,0 Antimony 0,1
Tin 4,0 – 6,0 Arsenic 0,03
Lead 2,5-3,0 Bismuth 0,02
Nickel 0,1-0,6 Cadmium 0,02
  Chromium 0,02
  Iron 0,3
  Silicon 0,01

Product Group B

Product Group C

Basis for Proposal: German Co-normative Research Report RG_CPDW_01_074, Dossier John Nuttall (March 2006)
 1.8.1.6. 

Constituent Content (%) Impurity Maximum (%)
Copper ≥ 99,9 Others total ≤ 0,1
Phosphorus ≤ 0,04  


Constituent EN number
Cu-DHP CW 024A

Elements for consideration in the migration water:

None: no need for comparative testing
 1.8.1.7. 

Constituent Content (%) Impurity Maximum (%)
Copper ≥ 99,9 Others total ≤ 0,1
Phosphorus ≤ 0,04  

Product group A

Product group B

Product group C

The formation of the copper compounds on the surface of copper pipes and consequently the dissolution is strongly influenced by minor components of the water composition. In some water compositions, the rate of leaching of copper may be unacceptably high. Member States may need to offer guidance to the water industry and to suppliers and installers of copper pipe on restrictions that may need to be introduced on use of copper pipe in water compositions where excessive leaching of copper might occur.

Further research into the compatibility of copper with certain compositions of water needs to be carried out using harmonised procedures for investigation and evaluation.

Research results and practical experience in several Member States are needed to characterise the conditions for safe use.
The contamination of drinking water by copper pipes depends on several characteristics of water composition. There is no consensus view on their combined action and interaction at this time. In particular, there is inadequate information on the range of compositions of drinking water where non-compliance with the DWD is likely to occur.
For tinned copper tubes and tinned copper fittings as base material copper according to 4.3.1 is used. On this substrate material a tin layer is deposited by different processes. By diffusion of copper ions into the tin layer the formation of an increasing intermetallic phase consisting of tin and copper (η-phase = Cu6Sn5) is formed.
 1.8.1.8. 

Constituent Content (%) Impurity of Maximum (%)
Tin and Copper 99,9 Antimony 0,01
  Arsenic 0,01
  Bismuth 0,01
  Cadmium 0,01
  Chromium 0,01
  Lead 0,01
  Nickel 0,01


Constituent EN number
Cu-DHP CW 024A
 1.8.1.9. 

Constituent Content (%) Impurity of Maximum (%)
Tin 90 Antimony 0,01
Copper < 10 Arsenic 0,01
  Bismuth 0,01
  Cadmium 0,01
  Chromium 0,01
  Lead 0,01
  Nickel 0,01

Product group A

Product group B

Product group C

arig tests in representative German drinking waters, published: A. Baukloh, S. Priggemeyer, U. Reiter, B. Winkler, Chemically inner tinned Copper Pipes, Less Copper in Corrosive Drinking Waters, Metall 10-11 (1998) 592 - 600.bRig tests according to DIN 50931 (rig test): Technical report DVGW/TZW, 2000


— Netherlands: according to BRL-K19005,
— Germany: according to DIN 50930, T6 and DVGW GW 392)
— Denmark, ETA
 1.8.1.10. 
The zinc coating resulting from used in the galvanising process shall comply with the following requirements.


Constituent Content (%) Impurity Maximum (%)
Zinc  Antimony 0,01
  Arsenic 0,02
  Cadmium 0,01
  Chromium 0,02
  Lead 0,05
  Bismuth 0,01
 1.8.1.11. 
The zinc coating resulting from used in the galvanising process complying with the following:


Constituent Content (%) Impurity Maximum (%)
Zinc  Antimony 0,01
  Arsenic 0,02
  Cadmium 0,01
  Chromium 0,02
  Lead 0,05
  Bismuth 0,01

The following formula is proposed as a means identifying water compositions where corrosion rates for galvanised steel is acceptable.

pH ≥ 7,5 or free CO2 ≤ 0,25 mmol/L

ANDAlkalinity ≥ 1,5 mmol/LANDS1 < 2 (definition of S1 below)ANDCalcium ≥ 0,5 mmol/LANDConductivity ≤ 600 μS/cm at 25 °CANDS2 < 1 or S2> 3 (definition of S2 below)

S1=cCl−+cNO−3+2 cSO2−4cHCO−3 concentrations in mmol/l

S2=cCl−+2 cSO2−4cNO−3 concentrations in mmol/l

Product group A

Product group B

Product group C

There are regulations with respect to water composition in France (DTU 60.1/NF P 40-201) and in Germany (DIN 50930-3). These limits are based on practical experience but are expressed in different ways. The proposal covers mainly the same water compositions as both regulations. The proposal takes into account available results from research in Germany and co-normative research.

The proposal incorporates also the recommendations given EN 12502-3 with regard to the risk of localised corrosion. This localised corrosion frequently leads to deterioration in water quality as a result of corrosion products of iron.

The proposal is based on results that have been obtained with galvanised steel pipes with lead concentrations between 1,0 % and 0,6 % in the zinc layer, assuming a similar behaviour of pipes with lower lead concentrations.

Carbon steel without permanent protective layers is not suitable for use in contact with drinking water.

Unprotected carbon steel can be used for specific applications (e.g. pumps, valves) and only for small surface in contact with water.
 1.8.1.12. 
The constituents and impurities should not exceed the maximum limits stated below:


Constituent Content (%) Impurity Maximum (%)
Iron  Antimony 0,02
Carbon ≤ 2,11 Arsenic 0,02
Chromium ≤ 1,0 Cadmium 0,02
Molybdenum ≤ 1,0 Lead 0,02
Nickel ≤ 0,5  
 1.8.1.13. 
The constituents and impurities should not exceed the maximum limits stated below:


Constituent Content (%) Impurity Maximum (%)
Iron  Antimony 0,02
Carbon ≤ 2,11 Arsenic 0,02
Chromium ≤ 1,0 Cadmium 0,02
Molybdenum ≤ 1,0 Lead 0,02
Nickel ≤ 0,5  

Group C

Draft Italian Regulation

Calculation of possible impact on DW

Cast iron without permanent protective layers is not suitable for pipes and fittings in contact with drinking water.

Unprotected cast iron can be used for specific applications (e.g. pumps, valves) and only for very small surface in contact with water. Their composition needs to be regulated.
 1.8.1.14. 
The constituents and impurities should not exceed the maximum limits stated below:


Constituent Content (%) Impurity Maximum (%)
  Antimony 0,02
Iron  Arsenic 0,02
Carbon  Cadmium 0,02
Chromium ≤ 1,0 Lead 0,02
Molybdenum ≤ 1,0  
Nickel ≤ 6,0  
 1.8.1.15. 
The constituents and impurities should not exceed the maximum limits stated below:


Constituent Content (%) Impurity Maximum (%)
  Antimony 0,02
Iron  Arsenic 0,02
Carbon  Cadmium 0,02
Chromium ≤ 1,0 Lead 0,02
Molybdenum ≤ 1,0  
Nickel ≤ 6,0  

Group C

Draft Italian regulation

French regulation

Calculation of possible impact on DW
