
CHAPTER I
Article 1 
This Decision establishes rules ... as regards:

((a)) appropriate authorities  obligations to report on the assessment and management of ambient air quality;
((b)) appropriate authorities  reciprocal exchange of information between each other  concerning networks and stations, and the measurements of air quality obtained from those stations that are selected by appropriate authorities for the purpose of reciprocal exchange from amongst existing stations.
Article 2 
For the purposes of this Decision, and in addition to the definitions laid down in Article 2 of Directive 2004/107/EC, Article 3 of Directive 2007/2/EC, and Article 2 of and Annex VII to Directive 2008/50/EC, the following definitions shall apply:

((1)) ‘station’ means a location where measurements or samples are taken at one or more sampling points at the same site within an area of approximately 100 m2;
((2)) ‘network’ means an organisational structure performing assessment of ambient air quality by measuring at one or more stations;
((3)) ‘measurement configuration’ means the technical facilities used for the measurement of one pollutant or one of its compounds at a certain station;
((4)) ‘measurement data’ means information on the concentration or deposition level of a specific pollutant obtained by measurements;
((5)) ‘modelling data’ means information on the concentration or deposition level of a specific pollutant obtained through numerical simulation of physical reality;
((6)) ‘objective estimation data’ means information on the concentration or deposition level of a specific pollutant obtained through expert analysis and may include use of statistical tools;
((7)) ‘primary data’ means information on the concentration or deposition level of a specific pollutant at the highest time resolution considered in this Decision;
((8)) ‘primary up-to-date assessment data’ means primary data collected with the frequency appropriate to each pollutant assessment method and made available to the public without delay;
((9)) ...
((10)) ‘data repository’ means an information system ... containing air quality information and data made available through national data reporting and exchange nodes under the control of the  appropriate authorities;
((11)) ‘data type’ means a descriptor by which similar data to be used for different purposes is categorised as set out in Part A of Annex II to this Decision;
((12)) ‘environmental objective’ means an ambient air quality objective to be attained within a given period, or where possible over a given period respectively or in the long term as laid down in Directives 2004/107/EC and 2008/50/EC.
((13)) “appropriate authority”
(a) in relation to England, the Secretary of State;
(b) in relation to Wales, the Welsh Ministers;
(c) in relation to Scotland, the Scottish Ministers;
(d) in relation to Northern Ireland, the Department of Agriculture, Environment and Rural Affairs.
((14)) For the purpose of this Decision a reference to a provision of a Directive is to be read as a reference to that provision in so far as it has been transposed into the law of any part of the United Kingdom.
CHAPTER II
Article 3 

1. Each appropriate authority, shall establish a data repository ....
2. The appropriate authority must include in its data repository information and data in accordance with Article 5.
3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. The public shall have access to the data repository free of charge.
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 4 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 5 

1. The appropriate authority  shall make available  in its  data repository the information required by this Decision in accordance with the data requirements set out in Part A of Annex I. ...
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER III
Article 6 

1. The appropriate authority must include in its data repository  the information set out in Part B of Annex II to this Decision on the delimitation and type of zones and agglomerations established in accordance with Article 3 of Directive 2004/107/EC and Article 4 of Directive 2008/50/EC and in which the assessment and management of air quality is to be carried out in the following calendar year....
2. The appropriate authoritymust include in its data repository  the information referred to in paragraph 1  by  no later than 31 December of each calendar year. The appropriate authority may indicate that there have been no changes to the information previously made available.
3. Where changes are made to the delimitation and type of zones and agglomerations, the  appropriate authority must update its data repository accordingly and by  no later than 9 months after the end of the calendar year the changes were made.
Article 7 

1. The appropriate authority must include in its data repository  the information set out in Part C of Annex II on the assessment regime to be applied in the following calendar year for each pollutant within individual zones and agglomerations in accordance with Article 4 of Directive 2004/107/EC and Articles 5 and 9 of Directive 2008/50/EC.
2. The appropriate authority must include in its data repository  the information referred to in paragraph 1  by  no later than 31 December of each calendar year.  The appropriate authority  may indicate that there have been no changes to the information previously made available.
Article 8 

1. The appropriate authority must include in its data repository  the information set out in Part D of Annex II on the methods used for the demonstration and subtraction of exceedances attributable to natural sources or to winter-sanding or -salting applied within individual zones and agglomerations according to Articles 20 and 21 of Directive 2008/50/EC.
2. The appropriate authorities must include in their data repository  the information referred to in paragraph 1 ... for a full calendar year no later than 9 months after the end of each calendar year.
Article 9 

1. The appropriate authority must include in its data repository  the information set out in Part D of Annex II on the quality and traceability of the assessment methods applied.
2. The appropriate authorities must include  the information referred to in paragraph 1 ... for a full calendar year no later than 9 months after the end of each calendar year.
3. Where in a particular zone or agglomeration fixed measurement is mandatory according to Article 4 of Directive 2004/107/EC and Articles 6 and 9 and Article 10(6) of Directive 2008/50/EC, the information shall include at least the following:
(a) the measurement configuration;
(b) the demonstration of equivalence where a non-reference method is used;
(c) the sampling point location, its description and classification;
(d) the documentation of data quality.
4. Where in a particular zone or agglomeration indicative measurement is applied in accordance with Article 4 of Directive 2004/107/EC and Articles 6 and 9 and Article 10(6) of Directive 2008/50/EC, the information shall include at least the following:
(a) the measurement method applied;
(b) the sampling points and the coverage area;
(c) the validation method;
(d) the documentation of data quality.
5. Where in a particular zone or agglomeration modelling techniques are applied in accordance with Article 4 of Directive 2004/107/EC and Articles 6 and 9 of Directive 2008/50/EC, the information shall include at least the following:
(a) the description of the modelling system and its inputs;
(b) the model validation through measurements;
(c) the coverage area;
(d) the documentation of data quality.
6. Where in a particular zone or agglomeration objective estimation is applied in accordance with Article 4 of Directive 2004/107/EC and Articles 6 and 9 of Directive 2008/50/EC, the information shall include at least the following:
(a) the description of the estimation method;
(b) the documentation of data quality.
7. The appropriate authority  shall also make available the information set out in Part D of Annex II on the quality and traceability of the assessment methods applied, for the networks and stations selected by the  appropriate authority  for the purpose of the reciprocal exchange of information as referred to in point (b) of Article 1 for the pollutants listed in Part B of Annex I and where available for the additional pollutants listed in Part C of Annex I and for the additional pollutants listed on the portal for that purpose. Paragraphs 1 to 6 of this Article shall apply to the exchanged information.
Article 10 

1. The appropriate authority must include in its data repository  the information set out in Part E of Annex II on primary validated assessment data for all sampling points where measurement data is collected for the purpose of the assessment ... according to Article 9 for the pollutants listed in Parts B and C of Annex I.Where in a particular zone or agglomeration modelling techniques are applied, ... the information set out in Part E of Annex II at the highest time resolution available must be included.
2. The primary validated assessment data shall be  included in the data repository  for a full calendar year as complete time series no later than 9 months after the end of each calendar year.
3. The appropriate authority must, where they make use of the possibility provided for in Articles 20(2) and 21(3) of Directive 2008/50/EC,  include in its data repository  information on the quantification of the contribution from natural sources pursuant to Article 20(1) of Directive 2008/50/EC or from the winter-sanding or -salting of roads pursuant to Article 21(1) and (2) of Directive 2008/50/EC.The information shall include:
(a) the spatial extent of the subtraction;
(b) the quantity of the primary validated assessment data made available according to paragraph 1 of this Article that can be attributed to natural sources or winter-sanding or -salting;
(c) the results of the application of the methods reported according to Article 8.
4. The appropriate authority must include in its data repository  the information set out in Part E of Annex II on primary up-to-date assessment data for the networks and stations selected ... for the specific purpose of making available up-to-date information amongst the networks and stations selected ... for the purpose of the reciprocal exchange of information as referred to in point (b) of Article 1 for the pollutants listed in Part B of Annex I and where available for the additional pollutants listed in Part C of Annex I ....
5. The appropriate authority must include in its data repository  the information set out in Part E of Annex II on primary validated assessment data for the networks and stations selected ... for the purpose of the reciprocal exchange of information as referred to in point (b) of Article 1 for the pollutants listed in Part B of Annex I and where available for the additional pollutants listed in Part C of Annex I .... Paragraphs 2 and 3 of this Article shall apply to the exchanged information.
6. The primary up-to-date assessment data pursuant to paragraph 4 shall be  included in the data repository  on a provisional basis with the frequency appropriate to each pollutant assessment method and within a reasonable timeframe after the data has been made available to the public according to Article 26 of Directive 2008/50/EC, for the pollutants specified for that purpose in Part B of Annex I to this Decision.The information shall include:
(a) assessed concentration levels;
(b) a status indication on the quality control.
7. The primary up-to-date information made available pursuant to paragraph 4 shall be coherent with the information made available pursuant to Articles 6, 7 and 9.
8. The appropriate authority  may update the primary up-to-date assessment data made available pursuant to paragraph 4 following further quality control. The updated information shall replace the original information and its status shall be clearly indicated.
Article 11 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 12 

1. The appropriate authority must include in its data repository  the information set out in Part G of Annex II on the attainment of environmental objectives set by Directives 2004/107/EC and 2008/50/EC.
2. The information referred to in paragraph 1 shall be  included in the data repository  for a full calendar year no later than 9 months after the end of each calendar year.The information shall include the following:
(a) a declaration of attainment of all environmental objectives in each specific zone or agglomeration, including information on the exceedance of any applicable margin of tolerance;
(b) where relevant, a declaration that the exceedance in the zone is attributable to natural sources;
(c) where relevant, a declaration that the exceedance of a PM10 air quality objective in the zone or agglomeration is due to the re-suspension of particulate matter following the winter-sanding or -salting of roads;
(d) information on the attainment of the PM2,5 exposure concentration obligation.
3. Where an exceedance has occurred, the information made available shall also include information on the area of exceedance and the number of people exposed.
4. The information made available shall be coherent with the zone delimitation made available pursuant to Article 6 for the same calendar year ....
Article 13 

1. The appropriate authority must include in its data repository  the information set out in Parts H, I, J and K of Annex II to this Decision on air quality plans as required by Article 23 of Directive 2008/50/EC including:
(a) the mandatory elements of the air quality plan as listed pursuant to Article 23 of Directive 2008/50/EC in Section A of Annex XV to Directive 2008/50/EC;
(b) references to where the public can have access to regularly updated information on the implementation of the air quality plans.
2. The information shall be  included in the data repository  without delay, and no later than 2 years after the end of the calendar year in which the first exceedance was observed.
Article 14 

1. The appropriate authority must include in its data repository  the information set out in Part K of Annex II to this Decision on measures taken to comply with the target values as required pursuant to Article 5(2) of Directive 2004/107/EC.
2. The information shall be  included in the data repository  no later than 2 years after the end of the year in which the exceedance triggering the measure was observed.
CHAPTER IV
Article 15 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 16 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 17 
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNEX I
(A)  (1) 
All time references shall be made available in accordance with the ISO standard 8601:2004(E) using the extended format (YYYY-MM-DDThh:mm:ss ± hh:mm) that includes the information on difference from UTC.

The time stamp refers to the end of the measurement period.
 (2) 
Data should be made available with the same number of digits as they are used in the monitoring network.

Rounding has to be the very last step of any calculation, i.e. immediately before comparing the result with the environmental objective and has to be done only once. By default the system will perform rounding of the data made available where appropriate following the commercial rounding rules.
 (3) 
When more than one assessment method is used at a specific location, data should be supplied using the assessment method exhibiting the lowest uncertainty at that specific location.
 (4) 
The provisions set out in Part IV of Annex IV to Directive 2004/107/EC and Part C of Annex VI to Directive 2008/50/EC should apply to the reciprocal exchange of information.
 (5) 
For PM2,5, in accordance with Part E of Annex XIV to Directive 2008/50/EC, the following sum of limit value (LV) + margin of tolerance (MOT) shall apply in the respective years mentioned below:


Year LV + MOT
2008 30
2009 29
2010 29
2011 28
2012 27
2013 26
2014 26
2015 25

Calculation is made for each individual year, calculating PM2,5 annual means for each of the selected sampling points. The selection of the sampling points has to be evident from the appropriate information made available.

Valid annual means complying with the data quality objectives are averaged over all designated AEI sites of the  appropriate authorities and the appropriate authorities in Wales, Scotland and Northern Ireland and the competent authority in England must cooperate with the Secretary of State to ensure the Secretary of State is able  to obtain an annual average.

The procedure is repeated for each of the 3 years, and the three annual averages are then averaged to obtain the AEI.

The AEI shall be made available annually as a three-year running mean. In case of a need to update any of the data that could directly or indirectly (through selection of sampling point) influence the AEI, the complete update of all affected information is necessary.

(B) 

Formula Protection target Environmental Objective type (Code) Averaging period of assessments Reporting metric of environmental objective Numerical values of the environmental objective(allowed number of exceedances)
Pollutants for which up-to-date and validated data have to be reported
NO2 Health LV 1 hour Hours in exceedance in a calendar year 200 μg/m3 (18)
LVMT
LV 1 calendar year Annual average 40 μg/m3
LVMT
ALT 1 hour Three consecutive hours in exceedance (at locations representative of air quality over at least 100 km2 or an entire zone or agglomeration, which ever is smaller) 400 μg/m3
NOx Vegetation CL 1 calendar year Annual average 30 μg/m3
PM10 Health LV 1 day Days in exceedance in a calendar year 50 μg/m3 (35)Percentile of 90,4
LV 1 calendar year Annual average 40 μg/m3
WSS 1 day Deducted days in exceedance in a calendar year n.a.
1 calendar year Deduction of annual average n.a.
NAT 1 day Deducted days in exceedance in a calendar year n.a.
1 calendar year Deduction of the annual average n.a.
PM2,5 Health ECO 3 subsequent calendar years Average Exposure Indicator (calculation see Directive 2008/50/EC) 20 μg/m3
ERT in accordance with Annex XIV, Part B to Directive 2008/50/EC
TV 1 calendar year Annual average 25 μg/m3
LV
LVMT
SO2 Health LV 1 hour Hours in exceedance in a calendar year 350 μg/m3 (24)
1 day Days in exceedance in a calendar year 125 μg/m3 (3)
ALT 1 hour Three consecutive hours in exceedance (at locations representative of air quality over at least 100 km2 or an entire zone or agglomeration, which ever is smaller) 500 μg/m3
NAT 1 hour Deducted hours in exceedance in a calendar year n.a.
1 day Deducted days in exceedance in a calendar year n.a.
Vegetation CL 1 calendar year Annual average 20 μg/m3
Winter Average value over the winter months, i.e. 1 October year x-1 to 31 March year x 20 μg/m3
O3 Health TV Maximum daily eight-hour mean Days when maximum daily eight-hour mean exceeded the target value averaged over 3 years 120 μg/m3 (25)
LTO Maximum daily eight-hour mean Days when maximum daily eight-hour mean exceeded the long term objective in 1 calendar year 120 μg/m3
INT 1 hour Hours in exceedance in a calendar year 180 μg/m3
ALT 1 hour Hours in exceedance in a calendar year 240 μg/m3
Vegetation TV 1 May to 31 July AOT40 (calculation see Dir. 2008/50/EC Annex VII) 18 000 μg/m3·h
LTO 1 May to 31 July AOT40 (calculation see Dir. 2008/50/EC Annex VII) 6 000 μg/m3 ·h
CO Health LV Maximum daily eight-hour mean Days when maximum daily eight-hour mean exceeded the limit value 10 mg/m3
Pollutants for which only validated data have to be reported
Benzene Health LV 1 calendar year Annual average 5 μg/m3
Lead Health LV 1 calendar year Annual average 0,5 μg/m3
Cadmium Health TV 1 calendar year Annual average 5 ng/m3
Arsenic Health TV 1 calendar year Annual average 6 ng/m3
Nickel
                                  
                                    Health
                                  
                                    TV
                                  
                                    1 calendar year
                                  
                                    Annual average
                                  
                                    20 ng/m
                                    
                                       3
B(a)P Health TV 1 calendar year Annual average 1 ng/m3



(C) 
The list includes all pollutants with monitoring requirements referred to in Directives 2004/107/EC and 2008/50/EC. ...


Airbase code Pollutant formula Pollutant name Measurement unit
Gaseous inorganic pollutants
1 SO2 Sulphur dioxide μg/m3
8 NO2 Nitrogen dioxide μg/m3
9 NOx Nitrogen oxides μg/m3
7 O3 Ozone μg/m3
10 CO Carbon monoxide mg/m3
Particulate Matter (PM)
5 PM10 PM10 μg/m3
6001 PM2,5 PM2,5 μg/m3
PM2,5 Speciation
1047
                                  
                                    SO
                                    
                                       4
                                    
                                       2-
                                    
                                     in PM
                                    
                                       2,5
                                     
                                    Sulphate in PM
                                    
                                       2,5
                                     
                                    μg/m
                                    
                                       3
1046 NO3- in PM2,5 Nitrate in PM2,5 μg/m3
1045 NH4+ in PM2,5 Ammonium in PM2,5 μg/m3
1771 elem. C in PM2,5 Elemental Carbon in PM2,5 μg/m3
1772 org. C in PM2,5 Organic Carbon in PM2,5 μg/m3
1629 Ca2 + in PM2,5 Calcium in PM2,5 μg/m3
1659 Mg2 + in PM2,5 Magnesium in PM2,5 μg/m3
1657 K + in PM2,5 Potassium in PM2,5 μg/m3
1668 Na + in PM2,5 Sodium in PM2,5 μg/m3
1631 Cl- in PM2,5 Chloride in PM2,5 μg/m3
Heavy Metals
5012
                                  
                                    Pb in PM
                                    
                                       10
                                     
                                    Lead in PM
                                    
                                       10
                                     
                                    μg/m
                                    
                                       3
                                    

                                    5014
                                  
                                    Cd in PM
                                    
                                       10
                                     
                                    Cadmium in PM
                                    
                                       10
                                     
                                    ng/m
                                    
                                       3
                                    

                                    5018
                                  
                                    As in PM
                                    
                                       10
                                     
                                    Arsenic in PM
                                    
                                       10
                                     
                                    ng/m
                                    
                                       3
                                    

                                    5015
                                  
                                    Ni in PM
                                    
                                       10
                                     
                                    Nickel in PM
                                    
                                       10
                                     
                                    ng/m
                                    
                                       3
Heavy Metals Deposition
7012
                                  
                                    Pb deposition
                                  
                                    wet/total Pb deposition
                                  
                                    μg/m
                                    
                                       2
                                    
                                    .day
                                 

                                    7014
                                  
                                    Cd deposition
                                  
                                    wet/total Cd deposition
                                  
                                    μg/m
                                    
                                       2
                                    
                                    .day
                                 

                                    7018
                                  
                                    As deposition
                                  
                                    wet/total As deposition
                                  
                                    μg/m
                                    
                                       2
                                    
                                    .day
                                 

                                    7015
                                  
                                    Ni deposition
                                  
                                    wet/total Ni deposition
                                  
                                    μg/m
                                    
                                       2
                                    
                                    .day
7013 Hg deposition wet/total Hg deposition μg/m2.day
Mercury
4013 Metallic gaseous Hg elemental gaseous Mercury ng/m3
4813 Total gaseous Hg Total gaseous Hg ng/m3
653 Reactive gaseous Hg reactive gaseous Mercury ng/m3
5013
                                  
                                    Hg in PM
                                    
                                       10
                                     
                                    Mercury in PM
                                    
                                       10
                                     
                                    ng/m
                                    
                                       3
Polycyclic Aromatic Hydrocarbons
5029 B(a)P Benzo(a)pyrene in PM10 ng/m3
5610 Benzo(a)anthracene Benzo(a)anthracene in PM10 ng/m3
5617 Benzo(b)fluoranthene Benzo(b)fluoranthene in PM10 ng/m3
5759 Benzo(j)fluoranthene Benzo(j)fluoranthene in PM10 ng/m3
5626 Benzo(k)fluoranthene Benzo(k)fluoranthene in PM10 ng/m3
5655 Indeno(1,2,3,-cd)pyrene Indeno(1,2,3,-cd)pyrene in PM10 ng/m3
5763 Dibenzo(a,h)anthracene Dibenzo(a,h)anthracene in PM10 ng/m3
Polycyclic Aromatic Hydrocarbons Deposition
7029 B(a)P Benzo(a)pyrene deposition μg/m2.day
611 Benzo(a)anthracene Benzo(a)anthracene deposition μg/m2.day
618 Benzo(b)fluoranthene Benzo(b)fluoranthene deposition μg/m2.day
760 Benzo(j)fluoranthene Benzo(j)fluoranthene deposition μg/m2.day
627 Benzo(k)fluoranthene Benzo(k)fluoranthene deposition μg/m2.day
656 Indeno(1,2,3,-cd)pyrene Indeno(1,2,3,-cd)pyrene deposition μg/m2.day
7419 Dibenzo(a,h)anthracene Dibenzo(a,h)anthracene deposition μg/m2.day
Volatile Organic Compounds
20 C6H6 Benzene μg/m3
428 C2H6 Ethane μg/m3
430 C2H4 Ethene (ethylene) μg/m3
432 HC≡CH Ethyne (acetylene) μg/m3
503 H3C-CH2-CH3 Propane μg/m3
505 CH2 = CH-CH3 Propene μg/m3
394 H3C-CH2-CH2-CH3 n-butane μg/m3
447 H3C-CH(CH3)2 2-methylproprane (i-butane) μg/m3
6005 H2C = CH-CH2-CH3 1-butene μg/m3
6006 H3C-CH = CH-CH3 trans-2-butene μg/m3
6007 H3C-CH = CH-CH3 cis-2-butene μg/m3
24 CH2 = CH-CH = CH2 1,3-butadiene μg/m3
486 H3C-(CH2)3-CH3 n-pentane μg/m3
450
                                  
                                    H
                                    
                                       3
                                    
                                    C-CH
                                    
                                       2
                                    
                                    -CH(CH
                                    
                                       3
                                    
                                    )
                                    
                                       2
                                     
                                    2-methylbutane (i-pentane)
                                  
                                    μg/m
                                    
                                       3
6008 H2C = CH-CH2-CH2-CH3 1-pentene μg/m3
6009 H3C-HC = CH-CH2-CH3 2-pentene μg/m3
451 CH2 = CH-C(CH3) = CH2 2-methyl-1,3-butadiene (isoprene) μg/m3
443 C6H14 n-hexane μg/m3
316 (CH3)2-CH-CH2-CH2-CH3 2-methylpentane (i-hexane) μg/m3
441 C7H16 n-heptane μg/m3
475 C8H18 n-octane μg/m3
449 (CH3)3-C-CH2-CH-(CH3)2 2,2,4-trimethylpentane (i-octane) μg/m3
21
                                  
                                    C
                                    
                                       6
                                    
                                    H
                                    
                                       5
                                    
                                    -CH
                                    
                                       3
                                     
                                    Toluene
                                  
                                    μg/m
                                    
                                       3
                                    

                                    431
                                  
                                    C
                                    
                                       6
                                    
                                    H
                                    
                                       5
                                    
                                    -C
                                    
                                       2
                                    
                                    H
                                    
                                       5
                                     
                                    Ethyl benzene
                                  
                                    μg/m
                                    
                                       3
                                    

                                    464
                                  
                                    m,p-C
                                    
                                       6
                                    
                                    H
                                    
                                       4
                                    
                                    (CH
                                    
                                       3
                                    
                                    )
                                    
                                       2
                                     
                                    m,p-xylene
                                  
                                    μg/m
                                    
                                       3
                                    

                                    482
                                  
                                    o-C
                                    
                                       6
                                    
                                    H
                                    
                                       4
                                    
                                    (CH
                                    
                                       3
                                    
                                    )
                                    
                                       2
                                     
                                    o-xylene
                                  
                                    μg/m
                                    
                                       3
6011 C6H3(CH3)3 1,2,4-trimethylbenzene μg/m3
6012 C6H3(CH3)3 1,2,3-trimethylbenzene μg/m3
6013 C6H3(CH3)3 1,3,5-trimethylbenzene μg/m3
32 THC(NM) total non methane Hydrocarbons μg/m3
25 HCHO Methanal (formaldehyde) μg/m3


ANNEX II
(A) 
Wherever a certain data type is to be made available pursuant to Parts B to K of this Annex, all information listed under the relevant data type specified below is to be included.
 (1)  1. Name of responsible authority, institution or body
 2. Name of responsible person
 3. Web address
 4. Address
 5. Telephone number
 6. E-mail
 (2)  1. Exceedance Situation ID
 2. Exceeded environmental objective
 3. Area of the exceedance situation (data type ‘Spatial Extent’)
 4. Classification of the area
 5. Administrative units
 6. Estimate of the surface area where the level was above the environmental objective
 7. Estimate of the length of road where the level was above the environmental objective
 8. Monitoring stations in exceedance area (link to D)
 9. Modelled exceedance (link to D)
 10. Estimate of the total resident population in the exceedance area
 11. Estimate of the ecosystem/vegetation area exposed above the environmental objective
 12. Reference year
 (3)  1. Objective type
 2. Averaging period of assessment
 3. Protection target
 (4)  1. GIS information provided as coordinates
 (5)  1. Spatial assessment data
 (6)  1. Publication
 2. Title
 3. Author(s)
 4. Publication date
 5. Publisher
 6. Web link
 (7)  1. Change
 2. Description of change

(B)  (1) Provider (data type ‘Contact Details’)
 (2) Change documentation (data type ‘Documentation of Change’)
 (3) Zone code
 (4) Zone name
 (5) Zone type
 (6) Zone delimitation (data type ‘Spatial Extent’)
 (7) Zone history: application start and end date
 (8) Predecessors (link to B)
 (9) Resident population
 (10) Resident population reference year
 (11) Code of designated pollutant
 (12) Protection Target
 (13) Exemption or postponement according to Article 22 of Directive 2008/50/EC

(C)  (1) Provider (data type ‘Contact Details’)
 (2) Change documentation (data type ‘Documentation of Change’)
 (3) Information on zone (link to B)
 (4) Pollutant
 (5) Environmental objective (data type ‘Environmental Objective’)
 (6) Attainment of assessment threshold
 (7) Assessment threshold classification year
 (8) Documentation of the classification (web link)
 (9) Assessment type
 (10) Assessment type: Description
 (11) Individual assessment metadata, including station ID, location information (link to D)
 (12) Authority responsible for the assessment of air quality (data type ‘Contact Details’)
 (13) Authority responsible for the approval of measurement systems (data type ‘Contact Details’)
 (14) Authority responsible for ensuring the accuracy of measurements (data type ‘Contact Details’)
 (15) Authority responsible for the analysis of assessment method (data type ‘Contact Details’)
 (16) Authority responsible for the coordination of nation-wide quality assurance (data type ‘Contact Details’)
 (17) ...

(D)  (i)  (1) Provider (data type ‘Contact Details’)
 (2) Change documentation (data type ‘Documentation of change’)
 (3) Assessment Type
 (4) Information on zone (Link to B)
 (5) Pollutant
 (ii)  (1) Measurement configuration ID
 (2) European station ID
 (3) Network ID
 (4) National station code
 (5) Name of the monitoring station
 (6) Name of the municipality
 (7) Measurement start and end date
 (8) Measurement type
 (9) Measurement/sampling/analytical method
 (10) Measurement/sampling equipment (where available)
 (11) Detection limit (where available)
 (12) Demonstration of equivalence
 (13) Demonstration of equivalence: Documentation (web link)
 (14) Sampling time
 (15) Sampling interval
 (16) Spatial Extent of representative area (data type ‘Spatial Extent’) (where available)
 (17) Evaluation of representativeness (where available)
 (18) Documentation of representativeness (web link) (where available)
 (19) Sampling point location: height of air inlet above ground
 (20) Sampling point location: horizontal distance of air inlet from the next building (for traffic stations)
 (21) Sampling point location: Distance of air inlet from nearest lane (for traffic stations)
 (22) Classification of station in relation to predominant emission sources relevant for the measurement configuration for each pollutant
 (23) Main sources (traffic, domestic heating, industrial sources or source area etc.) (where available)
 (24) Distance from predominant industrial source or source area (for industrial stations)
 (25) Station time references: start and end date
 (26) Geographical coordinates: longitude, latitude and altitude of monitoring station
 (27) Documentation of station information including maps and photographs (web link) (where available)
 (28) Classification of the area
 (29) Distance to major junction (for traffic stations)
 (30) Assessed traffic volume (for traffic stations)
 (31) Heavy-duty fraction of traffic (for traffic stations, where available)
 (32) Traffic speed (for traffic stations, where available)
 (33) Street canyon — width of street (for traffic stations, where available)
 (34) Street canyon — mean height of building facades (for traffic stations, where available)
 (35) Network name
 (36) Network: start and end date of operation
 (37) Body responsible for network management (data type ‘Contact Details’)
 (38) Assessment method for winter sanding and salting (where Article 21 of Directive 2008/50/EC applies)
 (39) Assessment method for natural contribution (where Article 20 of Directive 2008/50/EC applies)
 (40) Data quality objectives: time coverage
 (41) Data quality objectives: data capture
 (42) Data quality objectives: uncertainty estimation
 (43) Data quality objectives: documentation of traceability and uncertainty estimation
 (44) Data quality objectives: documentation of QA/QC (Web Link)
 (iii)  (1) Indicative measurement ID
 (2) Description of measurement method
 (3) Measurement type
 (4) Measurement method
 (5) Measurement/sampling equipment (where available)
 (6) Detection limit (where available)
 (7) Sampling time
 (8) Sampling interval
 (9) Geographical coordinates: geographical longitude, latitude and altitude
 (10) Assessment method for winter sanding and salting (where Article 21 of Directive 2008/50/EC applies)
 (11) Assessment method for natural contribution (where Article 20 of Directive 2008/50/EC applies)
 (12) Data quality objectives: time coverage
 (13) Data quality objectives: data capture
 (14) Data quality objectives: uncertainty estimation
 (15) Data quality objectives: documentation of traceability and uncertainty estimation
 (16) Data quality objectives: documentation of QA/QC (Web Link)
 (iv)  (1) Modelling ID
 (2) Environmental objective type (data type ‘Environmental Objective’)
 (3) Modelling method: name
 (4) Modelling method: description
 (5) Modelling method: documentation (web link)
 (6) Modelling method: validation by measurement
 (7) Modelling method: validation by measurement at sites not reported under the AQD
 (8) Modelling period
 (9) Area for modelling (data type ‘Spatial Extent’)
 (10) Spatial resolution
 (11) Assessment method for winter sanding and salting (where Article 21 of Directive 2008/50/EC applies)
 (12) Assessment method for natural contribution (where Article 20 of Directive 2008/50/EC applies)
 (13) Data quality objectives: uncertainty estimation
 (14) Data quality objectives: documentation of QA/QC (Web Link)
 (v)  (1) Objective estimation ID
 (2) Description
 (3) Area for objective estimation (data type ‘Spatial Extent’)
 (4) Data quality objective: uncertainty estimation
 (5) Data quality objectives: documentation of traceability and uncertainty estimation
 (6) Data quality objectives: documentation of QA/QC (Web Link)

(E)  (1) Provider (data type ‘Contact Details’)
 (2) Documentation of change (data type ‘Documentation of Change’)
 (3) Version number
 (4) Pollutant
 (5) Unit of pollutant
 (6) Assessment Type
 (7) Assessment Method (Link to D)
 (8) Start and end date of sampling
 (9) Time units and number of units of sampling
 (10) Measurement value (including quantity of pollutant concentration levels attributed to natural sources and winter-sanding and -salting (where Articles 20 and 21 of Directive 2008/50/EC apply))
 (11) Modelled value (data type ‘Spatial Observation’) (including quantity of pollutant concentration levels attributed to natural sources and winter-sanding and -salting (where Articles 20 and 21 of Directive 2008/50/EC apply))
 (12) Validity
 (13) Verification status

(F) 
 . . . . . . . . . . . . . . . . . .  . . . . . . . 

(G) 
This information must cover all zones and agglomerations and be fully coherent with the generated information under Part F of this Annex on aggregated validated assessment data for pollutants with defined environmental objectives.
 (1) Provider (data type ‘Contact Details’)
 (2) Reporting year
 (3) Change documentation (data type ‘Documentation of Change’)
 (4) Information on zone (link to B)
 (5) Exceedance situation (data type ‘Exceedance Situation’)
 (6) Pollutant
 (7) Assessment information (link to D)
 (8) Exceedance of the environmental objective
 (9) Exceedance of the environmental objective plus margin of tolerance
 (10) Exceedance taking into account natural sources
 (11) Exceedance taking into account winter sanding or salting
 (12) Exceedance situation after consideration of natural contributions and winter sanding or salting (data type ‘Exceedance Situation’).
 (13) Total numbers of exceedances (according to 8 to 11)

(H)  (1) Provider (data type ‘Contact Details’)
 (2) Change documentation (data type ‘Documentation of Change’)
 (3) Air quality plan: code
 (4) Air quality plan: name
 (5) Air quality plan: reference year of first exceedance
 (6) Competent authority (data type ‘Contact Details’)
 (7) Air quality plan: status
 (8) Air quality plan: pollutants covered
 (9) Air quality plan: date of official adoption
 (10) Air quality plan: timetable of implementation
 (11) Reference to air quality plan (web link)
 (12) Reference to implementation (web link)
 (13) Relevant publication (data type ‘Publication’)
 (14) Code of the relevant exceedance situation(s) (link to G)

(I)  (1) Code(s) of exceedance situation (link to G)
 (2) Reference year
 (3) Regional background: total
 (4) Regional background: from within Member State
 (5) Regional background: transboundary
 (6) Regional background: natural
 (7) Urban background increment: total
 (8) Urban background increment: traffic
 (9) Urban background increment: industry including heat and power production
 (10) Urban background increment: agriculture
 (11) Urban background increment: commercial and residential
 (12) Urban background increment: shipping
 (13) Urban background increment: off-road mobile machinery
 (14) Urban background increment: natural
 (15) Urban background increment: transboundary
 (16) Local increment: total
 (17) Local increment: traffic
 (18) Local increment: industry including heat and power production
 (19) Local increment: agriculture
 (20) Local increment: commercial and residential
 (21) Local increment: shipping
 (22) Local increment: off-road mobile machinery
 (23) Local increment: natural
 (24) Local increment: transboundary

(J)  (1) Code of exceedance situation (link to G)
 (2) Code of scenario
 (3) Code of air quality plan (link to H)
 (4) Reference year for which projections are developed
 (5) Reference year from which projections are started
 (6) Source apportionment (link to I)
 (7) Relevant publication (data type ‘Publication’)
 (8) Baseline: description of the emission scenario
 (9) Baseline: total emissions in the relevant spatial unit
 (10) Baseline: included measures (link to K)
 (11) Baseline: expected concentration levels in the projection year
 (12) Baseline: expected number of exceedances in the projection year
 (13) Projection: description of the emission scenario
 (14) Projection: total emissions in the relevant spatial unit
 (15) Projection: included measures (Link to K)
 (16) Projection: expected concentration levels in the projection year
 (17) Projection: expected number of exceedances in the projection year

(K)  (1) Code(s) of exceedance situation (link to G)
 (2) Code of air quality plan (link to H)
 (3) Code of evaluation scenario (link to J)
 (4) Measure: code
 (5) Measure: name
 (6) Measure: description
 (7) Measure: classification
 (8) Measure: type
 (9) Measure: administrative level
 (10) Measure: time scale
 (11) Measure: affected source sector
 (12) Measure: spatial scale
 (13) Estimated implementation costs (where available)
 (14) Planned implementation: start and end date
 (15) Date when the measure is planned to take full effect
 (16) Other key implementation dates
 (17) Indicator for monitoring progress
 (18) Reduction in annual emissions due to applied measure
 (19) Expected impact in level of concentrations in the projection year (where available)
 (20) Expected impact in number of exceedances in the projection year (where available)
