
Article 1 
The products and families of products set out in Annex I shall have their conformity attested by a procedure whereby, in addition to a factory production control system operated by the manufacturer, an approved body is involved in assessment and surveillance of the production control or of the product itself.
Article 2 
The procedure for attesting conformity as set out in Annex II shall be indicated in the mandates for harmonised European standards.
Article 3 
This Decision is addressed to the Member States.
Done at Brussels, 14 January 2011.
For the Commission
Antonio TAJANI
Vice-President
ANNEX I

Sealants for non-structural use in joints in buildings and pedestrian walkways as follows:

1.. sealants for external and/or internal walls, partitions;
2.. sealants for glazing (except for sealants for aquariums, structural glazing, first and outer seal to manufacture insulated glazing units, horizontal glazing (below 7°) and organic glass);
3.. sealants for sanitary joints (except for industrial, drinking water, underwater (swimming pools, sewage systems etc.) and food contact applications);
4.. sealants for pedestrian walkways (except for chemical containment, submersed, roads and other traffic areas, airports and sewage treatment plants).

ANNEX IINote: For products having more than one of the intended uses specified in the following families, the tasks for the approved body, derived from the relevant systems of attestation of conformity, are cumulative.
PRODUCT FAMILY 
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonised European standards:


Product Intended use Level(s) or class(es) AoC system
 — Sealants for external walls
 Outdoor applications — 3
 — Sealants for internal walls, partitions
 Indoor applications — 4
 — Sealants for glazing
 For uses in building construction — 3
 — Sealants for pedestrian walkways
 — 3
 — Sealants for sanitary joints
 — 3
System 3: See point (ii) of Section 2 of Annex III to Directive 89/106/EEC, second possibility.
System 4: See point (ii) of Section 2 of Annex III to Directive 89/106/EEC, third possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.

PRODUCT FAMILY 
For the product(s) and intended use(s) listed below, CEN/Cenelec is requested to specify the following system(s) of attestation of conformity in the relevant harmonised European standards:


Product(s) Intended use(s) Level(s) or class(es)(reaction to fire) Attestation of conformity system(s)
Sealants for non-structural use in joints in buildings and pedestrian walkways For uses subject to reaction to fire regulations A1, A2, B, C 1
A1, A2, B, C, D, E 3
(A1 to E), F 4



System 1: See point (i) of Section 2 of Annex III to Directive 89/106/EEC, without audit-testing of samples.
System 3: See point (ii) of Section 2 of Annex III to Directive 89/106/EEC, second possibility.
System 4: See point (ii) of Section 2 of Annex III to Directive 89/106/EEC, third possibility.

The specification for the system should be such that it can be implemented even where performance does not need to be determined for a certain characteristic, because at least one Member State has no legal requirement at all for such characteristic (see Article 2(1) of Directive 89/106/EEC and, where applicable, clause 1.2.3 of the Interpretative Documents). In those cases the verification of such a characteristic must not be imposed on the manufacturer if he does not wish to declare the performance of the product in that respect.
