
Article 1 
The undermentioned Directives are hereby amended in accordance with the Annexes to this Directive:

— Directive 70/157/EEC is amended in accordance with Annex I,
— Directive 70/220/EEC is amended in accordance with Annex II,
— Directive 72/245/EEC is amended in accordance with Annex III,
— Directive 72/306/EEC is amended in accordance with Annex IV,
— Directive 80/1268/EEC is amended in accordance with Annex V,
— Directive 80/1269/EEC is amended in accordance with Annex VI.
Article 2 
Member States shall bring into force the laws, regulations and administrative provisions necessary to comply with this Directive not later than 1 January 1990. They shall forthwith inform the Commission thereof.
Article 3 
This Directive is addressed to the Member States.
ANNEX I

6 is added as follows:
'
6.  6.1.  6.1.1. Approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended when the manufacturer certifies, subject to the approval of the authority granting type approval, that the sound level for the modified vehicle shall not exceed the limiting values specified in 5.2.2.1.
 6.2.  6.2.1. Approval of a vehicle type may be extended to vehicle types differing with regard to the characteristics listed in Annex III if the authority granting type approval considers that the modifications made are not likely to have any substantial adverse effect on the sound level of the vehicle.
'

ANNEX II

1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNEX III

8 is added as follows:
'
8.  8.1.  8.1.1. Approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended when the manufacturer certifies, subject to the radio interference suppression for the modified vehicles remain within the limits for conformity of production, as specified in 9 to this Annex.
 8.2.  8.2.1. Approval of a vehicle type may be extended to vehicle types differing with regard to the characteristics listed in 2.2 to this Annex if the authority granting type approval considers that the modification made are not likely to have any substantial adverse effect on the radio interference suppression of the vehicle.
'

ANNEX IV

Annex V is replaced by the following:
'
 Limits and units ASTM method
Cetan number min 49 D 613
max 53
Density 15 °C (Kg/l) min 0,835 D 1298
max 0,845 
Destillation 50 % min 245 °C D 86
90 % min 320 °C
max 340 °C
FBP max 370 °C
Flash point min 55 °C D 93
CFPP min – EN 116 (CEN)
max – 5 °C
Viscosity 40 °C min 2,5 mm2/S D 445
max 3,5 mm2/S
Sulphur content min (to be reported) D 1266/D 2622D 2785
max 0,3 % mass
Copper corrosion max 1 D 130
Conradson carbon residue (10 % DR) max 0,2 % mass D 189
Ash content max 0,01 % mass D 482
Water content max 0,05 % mass D 95/D 1744
Neutralization (strong acid) number max 0,2 mg KPH/g
Oxidation stability max 2,5 mg/100 m D 2274
Additives 
Carbon-hydrogen ratio (to be reported) 






'

ANNEX V

1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ANNEX VI

1. 8 is replaced by:
' 8.  8.1.  8.1.1. Subject to the approval of the authority granting type approval, approval of a vehicle type modified and/or adjusted solely for the purpose of making it capable of running on unleaded petrol, as specified in Directive 85/210/EEC, shall be extended under the following alternative conditions:
 8.1.1.1. The manufacturer shall certify that the engine power of the modified vehicle shall remain within the limits for conformity of production, as specified in 9.2 as obtained with the original, unmodified, type approved vehicle. In this case the extension shall confirm the power of the original type approval, or
 8.1.1.2. The manufacturer shall declare a revised engine power figure which is less than that obtained with the original, unmodified type approved vehicle. In this case the extension shall specify the newly declared figures as applicable to the modified vehicle type.
 8.2. 
Any other modification of the engine with regard to the characteristics listed in Appendix 1 or Apendix 2 to this Annex shall be reported to the competent authority. That authority may then either:
 8.2.1. consider that the modifications made are not likely to have any substantial effect on the power of the engine, or
 8.2.2. request a further determination of engine power through the carrying-out of such tests as are deemed necessary.
'

2. 9 is replaced by:
' 9.  9.1. The net power indicated by the manufacturer for the type of engine shall be accepted if it does not differ by more than ± 2 % for maximum power and more than ± 4 % at, the other measurement points on the curve with a tolerance of ± 1,5 % for engine speed, from the values measured by the technical service on the engine submitted for testing.
 9.2. During the tests to verify conformity of production the power shall be measured at two engine speeds S1 and S2 corresponding respectively to the measurement points of maximum power and maximum torque accepted for type approval. At these two engine speeds, which are subject to a tolerance of ± 5 %, the net power measured at at least one point within the ranges S1 ± 5 % and S2 ± 5 % shall not differ by more than ± 5 % from the approval figure.
'
