
Article 1 

1. Annex I to Regulation (EC) No 2003/2003 is amended in accordance with Annex I to this Regulation.
2. Annex II to Regulation (EC) No 2003/2003 is amended in accordance with Annex II to this Regulation.
3. Annex IV to Regulation (EC) No 2003/2003 is amended in accordance with Annex III to this Regulation.
Article 2 
By way of derogation from the second paragraph of Article 3, manufacturers may apply the provisions in Annex I, point (1) before 7 December 2014.
Article 3 

1. This Regulation shall enter into force on the twentieth day following that of its publication in the Official Journal of the European Union.
2. Annex I, point (1) shall apply from 7 December 2014.
3. Annex I, point (3), Annex II, point (2) and Annex III, point (4) shall apply from 7 June 2014.
This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Brussels, 17 May 2013.
For the Commission
The President
José Manuel BARROSO
ANNEX I

Annex I to Regulation (EC) No 2003/2003 is amended as follows:

((1)) In Section A.3, entries 1 and 2 in the table are replaced by the following:
'
1 Crude potassium salt Product obtained from crude potassium salts 10 % K2OPotassium expressed as water-soluble K2O5 % MgOMagnesium in the form of water-soluble salts, expressed as magnesium oxide Usual trade names may be added Water-soluble potassium oxideWater-soluble magnesium oxide
2 Enriched crude potassium salt Product obtained from crude potassium salts enriched by blending with potassium chloride 18 % K2OPotassium expressed as water-soluble K2O Usual trade names may be added Water-soluble potassium oxideOptional mention of the water-soluble magnesium oxide content where higher than 5 % MgO'
((2)) In Section E.3.2, the table is replaced by the following:

‘No Designation Alternative designation Chemical formula CAS number of the acid
1 Lignosulfonic acid LS No chemical formula available 8062-15-5


((3)) The following Section G is added:
'
G. 
The words “LIMING MATERIAL” shall be added after the term “EC FERTILISER”.

All the properties mentioned in the tables of Sections G.1 to G.5 refer to the product as supplied unless otherwise specified.

Granulated liming materials which are produced by aggregating smaller primary particles must break down when stirred in water into particles with fineness distributions as specified in the type descriptions, and as measured using Method 14.9 “Determination of the breakdown of granules”.
 G.1. 

No Type designation Data on method of production and essential ingredients Minimum content of nutrients (percentage by weight)Data on the expression of nutrientsOther requirements Other data on the type designation Nutrient content to be declaredForms and solubilities of the nutrientsOther criteria to be declared
1 2 3 4 5 6
1(a) Limestone — standard quality Product containing as its essential ingredient calcium carbonate, obtained by grinding of natural deposits of limestone. Minimum neutralising value: 42Fineness determined by wet sieving:
— at least 97 % to pass through a 3,15 mm sieve;
— at least 80 % to pass through a 1 mm sieve; and
— at least 50 % to pass through a 0,5 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Reactivity and method of determination (optional)Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
1(b) Limestone — fine quality Minimum neutralising value: 50Fineness determined by wet sieving:
— at least 97 % to pass through a 2 mm sieve;
— at least 80 % to pass through a 1 mm sieve;
— at least 50 % to pass through a 0,315 mm sieve; and
— at least 30 % to pass through a 0,1 mm sieve. Usual trade names or alternative names may be added.
2(a) Magnesian limestone — standard quality Product containing as its essential ingredients calcium carbonate and magnesium carbonate, obtained by grinding of natural deposits of magnesian limestone. Minimum neutralising value: 45Total magnesium: 3 % MgOFineness determined by wet sieving:
— at least 97 % to pass through a 3,15 mm sieve;
— at least 80 % to pass through a 1 mm sieve; and
— at least 50 % to pass through a 0,5 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumReactivity and method of determination (optional)Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
2(b) Magnesian limestone — fine quality Minimum neutralising value: 52Total magnesium: 3 % MgOFineness determined by wet sieving:
— at least 97 % to pass through a 2 mm sieve;
— at least 80 % to pass through a 1 mm sieve;
— at least 50 % to pass through a 0,315 mm sieve; and
— at least 30 % to pass through a 0,1 mm sieve. Usual trade names or alternative names may be added.
3(a) Dolomitic limestone — standard quality Product containing as its essential ingredients calcium carbonate and magnesium carbonate, obtained by grinding of natural deposits of dolomite. Minimum neutralising value: 48Total magnesium: 12 % MgOFineness determined by wet sieving:
— at least 97 % to pass through a 3,15 mm sieve;
— at least 80 % to pass through a 1 mm sieve; and
— at least 50 % to pass through a 0,5 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumReactivity and method of determination (optional)Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
3(b) Dolomitic limestone — fine quality Minimum neutralising value: 54Total magnesium: 12 % MgOFineness determined by wet sieving:
— at least 97 % to pass through a 2 mm sieve;
— at least 80 % to pass through a 1 mm sieve;
— at least 50 % to pass through a 0,315 mm sieve; and
— at least 30 % to pass through a 0,1 mm sieve. Usual trade names or alternative names may be added.
4(a) Marine limestone — standard quality Product containing as its essential ingredient calcium carbonate, obtained by grinding of natural deposits of limestone of marine origin. Minimum neutralising value: 30Fineness determined by wet sieving:
— at least 97 % to pass through a 3,15 mm sieve; and
— at least 80 % to pass through a 1 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Reactivity and method of determination (optional)Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
4(b) Marine limestone — fine quality Minimum neutralising value: 40Fineness determined by wet sieving:
— at least 97 % to pass through a 2 mm sieve; and
— at least 80 % to pass through a 1 mm sieve. Usual trade names or alternative names may be added.
5(a) Chalk — standard quality Product containing as its essential ingredient calcium carbonate, obtained by grinding of natural deposits of chalk. Fineness determined by wet sieving after disintegration in water:
— at least 90 % to pass through a 3,15 mm sieve;
— at least 70 % to pass through a 2 mm sieve; and
— at least 40 % to pass through a 0,315 mm sieve.Reactivity of fraction 1-2 mm (obtained by dry sieving) at least 40 % in citric acidMinimum neutralising value: 42Fineness determined by wet sieving:
— at least 97 % to pass through a 25 mm sieve; and
— at least 30 % to pass through a 2 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Reactivity and method of determination (optional)Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
5(b) Chalk — fine quality Fineness determined by wet sieving after disintegration in water:
— at least 97 % to pass through a 3,15 mm sieve;
— at least 70 % to pass through a 2 mm sieve; and
— at least 50 % to pass through a 0,315 mm sieve.Reactivity of fraction 1-2 mm (obtained by dry sieving) at least 65 % in citric acidMinimum neutralising value: 48Fineness determined by wet sieving:
— at least 97 % to pass through a 25 mm sieve; and
— at least 30 % to pass through a 2 mm sieve. Usual trade names or alternative names may be added.
6 Carbonate suspension Product containing as its essential ingredients calcium carbonate and/or magnesium carbonate, obtained by grinding and suspending in water of natural deposits of limestone, magnesian limestone, dolomite or chalk. Minimum neutralising value: 35Fineness determined by wet sieving:
— at least 97 % to pass through a 2 mm sieve;
— at least 80 % to pass through a 1 mm sieve;
— at least 50 % to pass through a 0,315 mm sieve; and
— at least 30 % to pass through a 0,1 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium if MgO ≥ 3 %Moisture (optional)Reactivity and method of determination (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
 G.2. 

No Type designation Data on method of production and essential ingredients Minimum content of nutrients (percentage by weight)Data on the expression of nutrientsOther requirements Other data on the type designation Nutrient content to be declaredForms and solubilities of the nutrientsOther criteria to be declared
1 2 3 4 5 6
1(a) Burnt lime — basic quality Product containing as its essential ingredient calcium oxide obtained by burning of natural deposits of limestone. Minimum neutralising value: 75Fineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Fineness determined by dry sieving (optional)Soil incubation results (optional)
1(b) Burnt lime — premium quality Product containing as its essential ingredient calcium oxide obtained by burning of natural deposits of limestone. Minimum neutralising value: 85Fineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Fineness determined by dry sieving (optional)Soil incubation results (optional)
2(a) Magnesian burnt lime — basic quality Product containing as its essential ingredients calcium oxide and magnesium oxide, obtained by burning of natural deposits of magnesian limestone. Minimum neutralising value: 80Total Magnesium: 7 % MgOFineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by dry sieving (optional)Soil incubation results (optional)
2(b) Magnesian burnt lime — premium quality Product containing as its essential ingredients calcium oxide and magnesium oxide, obtained by burning of natural deposits of magnesian limestone. Minimum neutralising value: 85Total Magnesium: 7 % MgOFineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by dry sieving (optional)Soil incubation results (optional)
3(a) Dolomitic burnt lime — basic quality Product containing as its essential ingredients calcium oxide and magnesium oxide, obtained by burning of natural deposits of dolomite. Minimum neutralising value: 85Total Magnesium: 17 % MgOFineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by dry sieving (optional)Soil incubation results (optional)
3(b) Dolomitic burnt lime — premium quality Product containing as its essential ingredients calcium oxide and magnesium oxide, obtained by burning of natural deposits of dolomite. Minimum neutralising value: 95Total Magnesium: 17 % MgOFineness determined by dry sieving:Fine:
— at least 97 % to pass through a 4 mm sieve.Screened:
— at least 97 % to pass through a 8 mm sieve; and
— no more than 5 % to pass through a 0,4 mm sieve. The type designation must include the fineness type “fine” or “screened”.Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by dry sieving (optional)Soil incubation results (optional)
4 Hydrated burnt lime (slaked lime) Product containing as its essential ingredients calcium hydroxide, obtained by burning and slaking of natural deposits of limestone. Minimum neutralising value: 65Fineness determined by wet sieving:
— at least 95 % to pass through a 0,16 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Fineness determined by wet sieving (optional)Moisture (optional)Soil incubation results (optional)
5 Hydrated magnesian burnt lime (slaked magnesian lime) Product containing as its essential ingredients calcium hydroxide and magnesium hydroxide, obtained by burning and slaking of natural deposits of magnesian limestone. Minimum neutralising value: 70Total Magnesium: 5 % MgOFineness determined by wet sieving:
— at least 95 % to pass through a 0,16 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by wet sieving (optional)Moisture (optional)Soil incubation results (optional)
6 Hydrated dolomitic burnt lime Product containing as its essential ingredients calcium hydroxide and magnesium hydroxide, obtained by burning and slaking, of natural deposits of dolomite. Minimum neutralising value: 70Total Magnesium: 12 % MgOFineness determined by wet sieving:
— at least 95 % to pass through a 0,16 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesiumFineness determined by wet sieving (optional)Moisture (optional)Soil incubation results (optional)
7 Hydrated lime suspension Product containing as its essential ingredients calcium hydroxide and/or magnesium hydroxide, obtained by burning, slaking and suspending in water of natural deposits of limestone, magnesian limestone or dolomite. Minimum neutralising value: 20Fineness determined by wet sieving:
— at least 95 % to pass through a 0,16 mm sieve. Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium if MgO ≥ 3 %Moisture (optional)Fineness determined by wet sieving (optional)Soil incubation results (optional)
 G.3. 

No Type designation Data on method of production and essential ingredients Minimum content of nutrients (percentage by weight)Data on the expression of nutrientsOther requirements Other data on the type designation Nutrient content to be declaredForms and solubilities of the nutrientsOther criteria to be declared
1 2 3 4 5 6
1(a) Sugar factory lime Product from sugar production obtained by carbonation using exclusively burnt lime from natural sources and containing as essential ingredient finely divided calcium carbonate. Minimum neutralising value: 20 Usual trade names or alternative names may be added. Neutralising valueTotal calciumTotal magnesium (optional)Moisture (optional)Reactivity and method of determination (optional)Soil incubation results (optional)
1(b) Sugar factory lime suspension Minimum neutralising value: 15
 G.4. 

No Type designation Data on method of production and essential ingredients Minimum content of nutrients (percentage by weight)Data on the expression of nutrientsOther requirements Other data on the type designation Nutrient content to be declaredForms and solubilities of the nutrientsOther criteria to be declared
1 2 3 4 5 6
1 Mixed lime Product obtained by mixing types listed in sections G1 and G2. Minimum carbonate content: 15 %Maximum carbonate content: 90 % The word “magnesian” shall be added to the type designation if MgO ≥ 5 %.Usual trade names or alternative names may be added. Types as specified in sections G.1 and G.2Neutralising valueTotal calciumTotal magnesium if MgO ≥ 3 %Soil incubation results (optional)Moisture (optional)
 G.5. 

No Type designation Data on method of production and essential ingredients Minimum content of nutrients (percentage by weight)Data on the expression of nutrientsOther requirements Other data on the type designation Nutrient content to be declaredForms and solubilities of the nutrientsOther criteria to be declared
1 2 3 4 5 6
1 Mixture of [type designation in section G.1 to G.4] with [type designation in section A, B, D]. Product obtained by mixing, compacting or granulating liming materials listed in sections G.1 to G.4 with fertiliser types listed in sections A, B or D.The following mixtures are prohibited:
— ammonium sulphate (Type A.1.4) or urea (Type A.1.9) with oxide limes or hydroxide limes listed in Section G.2;
— mixing and then compacting or granulating super phosphates of the types A.2.2(a), (b) or (c) with any of the types described in Section G.1 to G.4. Neutralising value: 153 % N for mixtures containing fertiliser types with a minimum N content3 % P2O5 for mixtures containing fertiliser types with a minimum content P2O53 % K2O for mixtures containing fertiliser types with a minimum content K2OPotassium expressed as water-soluble K2O Other requirements mentioned in the individual entries. Neutralising ValueNutrients according to the nutrient declarations of the individual fertiliser types.Total calciumTotal magnesium if MgO ≥ 3 %If the chloride content does not exceed 2 % Cl, the words “low in chloride” may be addedMoisture (optional)Fineness (optional)
'

ANNEX II

Annex II to Regulation (EC) No 2003/2003 is amended as follows:

((1)) Section 1.3 is amended as follows:

((a)) In the first entry, the type designation ‘kainit’ is replaced by ‘crude potassium salt’.
((b)) In the second entry, the type designation ‘enriched kainit salt’ is replaced by ‘enriched crude potassium salt’.
((2)) The following Section 5 is added:
'
5. 
The tolerances allowed in respect of the declared calcium and magnesium shall be:


Magnesium oxide:
 — up to and including 8 % MgO
 1
 — between 8 % and 16 % MgO
 2
 — more than 16 % MgO
 3
Calcium oxide 3

The tolerance allowed in respect of the declared neutralising value shall be:


Neutralising value 3

The tolerance applicable to the declared percentage of material passing a specific sieve shall be:


Fineness 10
'

ANNEX III

In Annex IV to Regulation (EC) No 2003/2003, Section B is amended as follows:

((1)) Method 6.1 is replaced by the following:
'
Method 6.1 
EN 16195: Fertilisers — Determination of chlorides in the absence of organic material

This method of analysis has been ring-tested.
'
((2)) Methods 8.6 to 8.8 are replaced by the following:
'
Method 8.6 
EN 16196: Fertilisers — Manganimetric determination of extracted calcium following precipitation in the form of oxalate

This method of analysis has been ring-tested.

Method 8.7 
EN 16197: Fertilisers — Determination of magnesium by atomic absorption spectrometry

This method of analysis has been ring-tested.

Method 8.8 
EN 16198: Fertilisers — Determination of magnesium by complexometry

This method of analysis has been ring-tested.
'
((3)) Method 8.10 is replaced by the following:
'
Method 8.10 
EN 16199: Fertilisers — Determination of the sodium extracted by flame-emission spectrometry

This method of analysis has been ring-tested.
'
((4)) The following methods 14 are added:
'
Methods 14  Method 14.1 
EN 12948: Liming materials — Determination of size distribution by dry and wet sieving

This method of analysis has been ring-tested.
 Method 14.2 
EN 13971: Carbonate and silicate liming materials — Determination of reactivity — Potentiometric titration method with hydrochloric acid

This method of analysis has been ring-tested.
 Method 14.3 
EN 16357: Carbonate liming materials — Determination of reactivity — Automatic titration method with citric acid

This method of analysis has been ring-tested.
 Method 14.4 
EN 12945: Liming materials — Determination of neutralising value — Titrimetric methods

This method of analysis has been ring-tested.
 Method 14.5 
EN 13475: Liming materials — Determination of calcium content — Oxalate method

This method of analysis has been ring-tested.
 Method 14.6 
EN 12946: Liming materials — Determination of calcium and magnesium content — Complexometric method

This method of analysis has been ring-tested.
 Method 14.7 
EN 12947: Liming materials — Determination of magnesium content — Atomic absorption spectrometric method

This method of analysis has been ring-tested.
 Method 14.8 
EN 12048 Solid fertilisers and liming materials — Determination of moisture content — Gravimetric method by drying at 105 °C +/– 2 °C

This method of analysis has been ring-tested.
 Method 14.9 
EN 15704: Liming materials — Determination of the breakdown of granulated calcium and calcium/magnesium carbonates under the influence of water

This method of analysis has been ring-tested.
 Method 14.10 
EN 14984: Liming materials — Determination of product effect on soil pH — Soil incubation method

This method of analysis has been ring-tested.
'
