
Article 1 
In Article 2 of Decision 2006/771/EC, the following point is added:
'
3.. “category of short-range devices” means a group of short-range devices that use spectrum with similar technical spectrum access mechanisms or based on common usage scenarios'
Article 2 
Article 3 of Decision 2006/771/EC is replaced by the following.
'
Article 3 

1. Member States shall designate and make available, on a non-exclusive, non-interference and non-protected basis, the frequency bands for the categories of short-range devices, subject to the specific conditions and by the implementation deadline, as laid down in the Annex to this Decision.
2. Notwithstanding paragraph 1, Member States may request the benefit of Article 4(5) of the Radio Spectrum Decision.
3. This Decision is without prejudice to the right of Member States to allow the use of the frequency bands under less restrictive conditions or for short-range devices which are not part of the harmonised category provided that this does not prevent or reduce the possibility for short-range devices of such a category to rely on the appropriate set of harmonised technical and operational conditions, as specified in the Annex to this Decision, which allow the shared use of a specific part of the spectrum on a non-exclusive basis and for different purposes by short range devices of the same category.'
Article 3 
The Annex to Decision 2006/771/EC is replaced by the text in the Annex to this Decision.
Article 4 
Decision 2005/928/EC is repealed.
Article 5 
Member States shall report to the Commission on the implementation of this Decision no later than 1 September 2014.
Article 6 
This Decision is addressed to the Member States.
Done at Brussels, 11 December 2013.
For the Commission
Neelie KROES
Vice-President
ANNEX


‘ANNEX 
Band no Frequency band Category of short-range devices Transmit power limit/field strength limit/power density limit Additional parameters (channelling and/or channel access and occupation rules) Other usage restrictions Implementation deadline
1 9-59,750 kHz Inductive devices 72 dΒμΑ/m at 10 metres   1 July 2014
2 9-315 kHz Active medical implant devices 30 dΒμΑ/m at 10 metres Duty cycle limit: 10 % This set of usage conditions is only available to active implantable medical devices. 1 July 2014
3 59,750-60,250 kHz Inductive devices 42 dΒμΑ/m at 10 metres   1 July 2014
4 60,250-74,750 kHz Inductive devices 72 dBμA/m at 10 metres   1 July 2014
5 74,750-75,250 kHz Inductive devices 42 dBμA/m at 10 metres   1 July 2014
6 75,250-77,250 kHz Inductive devices 72 dBμA/m at 10 metres   1 July 2014
7 77,250-77,750 kHz Inductive devices 42 dBμA/m at 10 metres   1 July 2014
8 77,750-90 kHz Inductive devices 72 dBμA/m at 10 metres   1 July 2014
9 90-119 kHz Inductive devices 42 dBμA/m at 10 metres   1 July 2014
10 119-128,6 kHz Inductive devices 66 dBμA/m at 10 metres   1 July 2014
11 128,6-129,6 kHz Inductive devices 42 dBμA/m at 10 metres   1 July 2014
12 129,6-135 kHz Inductive devices 66 dBμA/m at 10 metres   1 July 2014
13 135-140 kHz Inductive devices 42 dBμA/m at 10 metres   1 July 2014
14 140-148,5 kHz Inductive devices 37,7 dΒμΑ/m at 10 metres   1 July 2014
15 148,5-5 000 kHz Inductive devices – 15 dΒμΑ/m at 10 metres in any bandwidth of 10 kHz.Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz   1 July 2014
16 315-600 kHz Active medical implant devices – 5 dΒμΑ/m at 10 m Duty cycle limit: 10 % This set of usage conditions is only available to animal implantable devices. 1 July 2014
17 400-600 kHz Radio Frequency Identification (RFID) devices – 8 dΒμΑ/m at 10 metres   1 July 2014
18 456,9-457,1 kHz Non-specific short-range devices 7 dBμA/m at 10 m  This set of usage conditions is only available for emergency detections of buried victims and valuable items devices. 1 July 2014
19 984-7 484 kHz Transport and Traffic Telematics devices 9 dΒμΑ/m at 10 m Duty cycle limit: 1 % This set of usage conditions is only available for Eurobalise transmissions in the presence of trains and using the 27 MHz band for telepowering. 1 July 2014
20 3 155-3 400 kHz Inductive devices 13,5 dΒμΑ/m at 10 metres   1 July 2014
21 5 000-30 000 kHz Inductive devices – 20 dΒμΑ/m at 10 metres in any bandwidth of 10 kHz. Furthermore the total field strength is – 5 dΒμΑ/m at 10 m for systems operating at bandwidths larger than 10 kHz   1 July 2014
22a 6 765-6 795 kHz Inductive devices 42 dΒμΑ/m at 10 metres   1 July 2014
22b 6 765-6 795 kHz Non-specific short-range devices 42 dΒμΑ/m at 10 metres   1 July 2014
23 7 300-23 000 kHz Transport and Traffic Telematics devices – 7 dΒμΑ/m at 10 m Antenna restrictions apply as specified in the harmonised standards adopted under Directive 1999/5/EC. This set of usage conditions is only available for Euroloop transmissions in the presence of trains and using the 27 MHz band for telepowering. 1 July 2014
24 7 400-8 800 kHz Inductive devices 9 dΒμΑ/m at 10 metres   1 July 2014
25 10 200-11 000 kHz Inductive devices 9 dΒμΑ/m at 10 metres   1 July 2014
26 12 500-20 000 kHz Active medical implant devices – 7 dΒμΑ/m at 10 m in a bandwidth of 10 kHz Duty cycle limit: 10 % This set of usage conditions is only available to indoor use by animal implantable devices. 1 July 2014
27a 13 553-13 567 kHz Inductive devices 42 dΒμΑ/m at 10 metres   1 July 2014
27b 13 553-13 567 kHz Radio Frequency Identification (RFID) devices 60 dΒμΑ/m at 10 metres   1 July 2014
27c 13 553-13 567 kHz Non-specific short-range devices 42 dΒμΑ/m at 10 metres   1 July 2014
28a 26 957-27 283 kHz Inductive devices 42 dΒμΑ/m at 10 metres   1 July 2014
28b 26 957-27 283 kHz Non-specific short-range devices 10 mW effective radiated power (e.r.p.), which corresponds to 42 dΒμΑ/m at 10 metres   1 July 2014
29 26 990-27 000 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 % Model control devices may operate without duty cycle restrictions. 1 July 2014
30 27 040-27 050 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 % Model control devices may operate without duty cycle restrictions. 1 July 2014
31 27 090-27 100 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 % Model control devices may operate without duty cycle restrictions. 1 July 2014
32 27 140-27 150 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 % Model control devices may operate without duty cycle restrictions. 1 July 2014
33 27 190-27 200 kHz Non-specific short-range devices 100 mW e.r.p. Duty cycle limit: 0,1 % Model control devices may operate without duty cycle restrictions. 1 July 2014
34 30-37,5 MHz Active medical implant devices 1 mW e.r.p. Duty cycle limit: 10 % This set of usage conditions is only available to ultra-low power medical membrane implants for blood pressure measurements within the definition of active implantable medical devices in Directive 90/385/EEC. 1 July 2014
35 40,66-40,7 MHz Non-specific short-range devices 10 mW e.r.p.  Video applications are excluded. 1 July 2014
36 87,5-108 MHz High duty cycle/continuous transmission devices 50 nW e.r.p. Channel spacing up to 200 kHz. This set of usage conditions is only available to transmitters with analogue frequency modulation (FM). 1 July 2014
37a 169,4-169,475 MHz Assistive Listening Devices (ALD) 500 mW e.r.p. Channel spacing: max 50 kHz.  1 July 2014
37b 169,4-169,475 MHz Metering devices 500 mW e.r.p. Channel spacing: max 50 kHz. Duty cycle limit: 10,0 %.  1 July 2014
37c 169,4-169,475 MHz Non-specific short-range devices 500 mW e.r.p. Channel spacing: max 50 kHz. Duty cycle limit: 1,0 %.  1 July 2014
38 169,4-169,4875 MHz Non-specific short-range devices 10 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limit: 0,1 %.  1 July 2014
39a 169,4875-169,5875 MHz Assistive Listening Devices (ALD) 500 mW e.r.p. Channel spacing: max 50 kHz.  1 July 2014
39b 169,4875-169,5875 MHz Non-specific short-range devices 10 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limit: 0,001 %. Between 00.00 and 06.00 local time a duty cycle limit of 0,1 % may be used. 1 July 2014
40 169,5875-169,8125 MHz Non-specific short-range devices 10 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limit: 0,1 %.  1 July 2014
41 401-402 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz. Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used. This set of usage conditions is only available for systems specifically designed for the purpose of providing non-voice digital communications between active implantable medical devices and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. 1 July 2014
42 402-405 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz. Individual transmitters may combine adjacent channels for increased bandwidth up to 300 kHz. Other techniques to access spectrum or mitigate interference, including bandwidths greater than 300 kHz, can be used provided they result at least in an equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC to ensure compatible operation with the other users and in particular with meteorological radiosondes. This set of usage conditions is only available to active implantable medical devices. 1 July 2014
43 405-406 MHz Active medical implant devices 25 μW e.r.p. Channel spacing: 25 kHz Individual transmitters may combine adjacent channels for increased bandwidth up to 100 kHz. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used. This set of usage conditions is only available for systems specifically designed for the purpose of providing non-voice digital communications between active implantable medical devices and/or body-worn devices and other devices external to the human body used for transferring non-time critical individual patient-related physiological information. 1 July 2014
44a 433,05-434,04 MHz Non-specific short-range devices 1 mW e.r.p. and – 13 dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications are allowed with advanced mitigation techniques. Audio and video applications are excluded. 1 July 2014
44b 433,05-434,04 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
45a 434,04-434,79 MHz Non-specific short-range devices 1 mW e.r.p. and – 13 dBm/10 kHz power density for bandwidth modulation larger than 250 kHz Voice applications are allowed with advanced mitigation techniques. Audio and video applications are excluded. 1 July 2014
45b 434,04-434,79 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 10 % Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
45c 434,04-434,79 MHz Non-specific short-range devices 10 mW e.r.p. Duty cycle limit: 100 % subject to channel spacing up to 25 kHz. Voice applications are allowed with advanced mitigation techniques. Audio and video applications are excluded. 1 July 2014
46a 863-865 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used. Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
46b 863-865 MHz High duty cycle/continuous transmission devices 10 mW e.r.p.  This set of usage conditions is only available to wireless audio and multimedia streaming devices. 1 July 2014
47 865-868 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used. Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
48 868-868,6 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used. Analogue video applications are excluded. 1 July 2014
49 868,6-868,7 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz The whole frequency band may also be used as a single channel for high-speed data transmission.Duty cycle limit: 1,0 % This set of usage conditions is only available to alarm systems. 1 July 2014
50 868,7-869,2 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used. Analogue video applications are excluded. 1 July 2014
51 869,2-869,25 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz. Duty cycle limit: 0,1 % This set of usage conditions is only available to social alarm devices. 1 July 2014
52 869,25-869,3 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit: 0,1 % This set of usage conditions is only available to alarm systems. 1 July 2014
53 869,3-869,4 MHz Low duty cycle/high reliability devices 10 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit: 1,0 % This set of usage conditions is only available to alarm systems. 1 July 2014
54a 869,4-869,65 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 0,1 % may also be used. Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
54b 869,4-869,65 MHz Non-specific short-range devices 500 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a Duty cycle limit of 10 % may also be used. Analogue video applications are excluded. 1 July 2014
55 869,65-869,7 MHz Low duty cycle/high reliability devices 25 mW e.r.p. Channel spacing: 25 kHz Duty cycle limit: 10 % This set of usage conditions is only available to alarm systems. 1 July 2014
56a 869,7-870 MHz Non-specific short-range devices 5 mW e.r.p. Voice applications allowed with advanced mitigation techniques. Audio and video applications are excluded. 1 July 2014
56b 869,7-870 MHz Non-specific short-range devices 25 mW e.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Alternatively a duty cycle limit of 1 % may also be used. Analogue audio applications other than voice are excluded. Analogue video applications are excluded. 1 July 2014
57a 2 400-2 483,5 MHz Non-specific short-range devices 10 mW equivalent isotropic radiated power (e.i.r.p.)   1 July 2014
57b 2 400-2 483,5 MHz Radio determination devices 25 mW e.i.r.p.   1 July 2014
57c 2 400-2 483,5 MHz Wideband data transmission devices 100 mW e.i.r.p. and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used.  1 July 2014
58 2 446-2 454 MHz Radio Frequency Identification (RFID) devices 500 mW e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used.  1 July 2014
59 2 483,5-2 500 MHz Active medical implant devices 10 mW e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Channel spacing: 1 MHz. The whole frequency band may also be used dynamically as a single channel for high-speed data transmissions. Duty cycle limit of 10 %. This set of usage conditions is only available to active implantable medical devices.Peripheral master units are for indoor use only. 1 July 2014
60 4 500-7 000 MHz Radio determination devices 24 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Tank Level Probing Radar. 1 July 2014
61 5 725-5 875 MHz Non-specific short-range devices 25 mW e.i.r.p.   1 July 2014
62 5 795-5 805 MHz Transport and Traffic Telematics devices 2 W e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions applies only to road tolling applications. 1 July 2014
63 6 000-8 500 MHz Radio determination devices 7 dBm/50 MHz peak e.i.r.p. and – 33 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as equivalent techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Level Probing Radar.Established exclusion zones around radio astronomy sites must be obeyed. 1 July 2014
64 8 500-10 600 MHz Radio determination devices 30 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Tank Level Probing Radar. 1 July 2014
65 17,1-17,3 GHz Radio determination devices 26 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to ground-based systems. 1 July 2014
66 24,05-24,075 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p.   1 July 2014
67 24,05-26,5 GHz Radio determination devices 26 dBm/50 MHz peak e.i.r.p. and – 14 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as equivalent techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Level Probing Radar.Established exclusion zones around radio astronomy sites must be obeyed. 1 July 2014
68 24,05-27 GHz Radio determination devices 43 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Tank Level Probing Radar. 1 July 2014
69a 24,075-24,15 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Dwell time limits and frequency modulation range apply as specified in harmonised standards. This set of usage conditions is only available to ground-based vehicle radars. 1 July 2014
69b 24,075-24,15 GHz Transport and Traffic Telematics devices 0,1 mW e.i.r.p.   1 July 2014
70a 24,15-24,25 GHz Non-specific short-range devices 100 mW e.i.r.p.   1 July 2014
70b 24,15-24,25 GHz Transport and Traffic Telematics devices 100 mW e.i.r.p.   1 July 2014
71 24,25-24,495 GHz Transport and Traffic Telematics devices – 11 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limits and frequency modulation ranges apply as specified in harmonised standards. This set of usage conditions is only available to ground-based vehicle radars operating in the harmonised 24 GHz frequency range. 1 July 2014
72 24,25-24,5 GHz Transport and Traffic Telematics devices 20 dBm e.i.r.p. (forward-facing radars) 16 dBm e.i.r.p. (rear-facing radars) Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limits and frequency modulation range apply as specified in harmonised standards. This set of usage conditions is only available to ground-based vehicle radars operating in the harmonised 24 GHz frequency range. 1 July 2014
73 24,495-24,5 GHz Transport and Traffic Telematics devices – 8 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Duty cycle limits and frequency modulation range apply as specified in harmonised standards. This set of usage conditions is only available to ground-based vehicle radars operating in the harmonised 24 GHz frequency range. 1 July 2014
74a 57-64 GHz Non-specific short-range devices 100 mW e.i.r.p., a maximum transmit power of 10 dBm and a maximum e.i.r.p. power spectral density of 13 dBm/MHz   1 July 2014
74b 57-64 GHz Radio determination devices 43 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Tank Level Probing Radar. 1 July 2014
74c 57-64 GHz Radio determination devices 35 dBm/50 MHz peak e.i.r.p. and – 2 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as equivalent techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Level Probing Radar. 1 July 2014
75 57-66 GHz Wideband data transmission devices 40 dBm e.i.r.p. and 13 dBm/MHz e.i.r.p. density Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. Fixed outdoor installations are excluded. 1 July 2014
76 61-61,5 GHz Non-specific short-range devices 100 mW e.i.r.p.   1 July 2014
77 63-64 GHz Transport and Traffic Telematics devices 40 dBm e.i.r.p.  This set of usage conditions is only available to vehicle-to-vehicle, vehicle-to-infrastructure and infrastructure-to-vehicle systems. 1 July 2014
78a 75-85 GHz Radio determination devices 34 dBm/50 MHz peak e.i.r.p. and – 3 dBm/MHz mean e.i.r.p. Automatic power control and antenna requirements as well as equivalent techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Level Probing Radar.Established exclusion zones around radio astronomy sites must be obeyed. 1 July 2014
78b 75-85 GHz Radio determination devices 43 dBm e.i.r.p. Techniques to access spectrum and mitigate interference that provide at least equivalent performance to the techniques described in harmonised standards adopted under Directive 1999/5/EC must be used. This set of usage conditions is only available to Tank Level Probing Radar. 1 July 2014
79 76-77 GHz Transport and Traffic Telematics devices 55 dBm peak e.i.r.p. and 50 dBm mean e.i.r.p. and 23,5 dBm mean e.i.r.p. for pulse radars  This set of usage conditions is only available to ground-based vehicle and infrastructure systems. 1 July 2014
80 122-123 GHz Non-specific short-range devices 100 mW e.i.r.p.   1 July 2014
81 244-246 GHz Non-specific short-range devices 100 mW e.i.r.p.   1 July 2014

























