
Article 1 
Decision 2012/88/EU is amended as follows:

((1)) Article 6 is deleted.
((2)) The following Article is inserted:
'
Article 6a 
When implementing the TSI set out in Annex III to this Decision, one of the two sets of specifications listed in table A-2 of Annex A shall be applied. Baseline 3 specifications shall be maintained in order to ensure that trains equipped with Baseline 3-compliant ERTMS/ETCS can run on Baseline 2-compliant ERTMS/ETCS lines without any additional technical or operational restrictions.'
((3)) Annex A is replaced by Annex I to this Decision.
((4)) Annex G is replaced by Annex II to this Decision
Article 2 
This Decision shall apply from 1 January 2013.
Article 3 
This Decision is addressed to the Member States.
Done at Brussels, 6 November 2012.
For the Commission
Siim KALLAS
Vice-President
ANNEX I


ANNEX A 
For each reference made in the basic parameters (Chapter 4 of this TSI) the following table indicates the corresponding mandatory specifications, via the index in table A-2.


Reference in Chapter 4 Index number (see Table A 2)
4.1
4.1 a 1, 4
4.1 b 32
4.1 c 3
 
4.2.1
4.2.1 a 27, 78
4.2.1 b 28
 
4.2.2
4.2.2.a 14
4.2.2.b 1, 4, 13, 15, 60
4.2.2.c 31, 37b, c, d
4.2.2.d 18, 20
4.2.2.e 6
4.2.2.f 7
 
4.2.3
4.2.3 a 14
4.2.3 b 1, 4, 13, 15, 60
4.2.3 c 31, 37 b, c, d
4.2.3 d 18, 21
 
4.2.4
4.2.4 a 64, 65
4.2.4 b 66
4.2.4 c 67
4.2.4 d 68
4.2.4 e 73, 74
4.2.4 f 32, 33
4.2.4 g 48
4.2.4 h 69, 70
4.2.4 j 71, 72
4.2.4 k 75, 76
 
4.2.5
4.2.5 a 64, 65
4.2.5 b 10, 39, 40
4.2.5 c 19, 20
4.2.5 d 9, 43
4.2.5 e 16, 50
 
4.2.6
4.2.6 a 8, 25, 26, 36 c, 49, 52
4.2.6 b 29, 45
4.2.6 c 46
4.2.6 d 34
4.2.6 e 20
4.2.6 f 44
 
4.2.7
4.2.7 a 12
4.2.7 b 62, 63
4.2.7 c 34
4.2.7 d 9
4.2.7 e 16
 
4.2.8
4.2.8 a 11, 79
 
4.2.9
4.2.9 a 23
 
4.2.10
4.2.10 a 77 (section 3.1)
 
4.2.11
4.2.11 a 77 (section 3.2)
 
4.2.12
4.2.12 a 6, 51
 
4.2.13
4.2.13 a 32, 33, 51, 80
 
4.2.14
4.2.14 a 5
 
4.2.15
4.2.15 a 38

One of the two sets of specifications listed in Table A-2 of this Annex shall be applied.

Documents referred to within a specification listed in Table A-2 shall be considered as being for information only, unless otherwise stated in Table A-2.
 Note: specifications indicated as ‘Reserved’ in table A-2 are also listed as open points in Annex G when there is a need for notification of national rules to close the corresponding open points. Reserved documents not listed as open points are intended as improvements to the system.
 Table A 2 

Index N Set of specifications # 1(ETCS baseline 2 and GSM-R baseline 0) Set of specifications # 2(ETCS baseline 3 and GSM-R baseline 0)
Reference Name of Specification Version Notes Reference Name of Specification Version Notes
1 ERA/ERTMS/003204 ERTMS/ETCS Functional requirement specification 5.0  Intentionally deleted   
2 Intentionally deleted    Intentionally deleted   
3 UNISIG SUBSET-023 Glossary of Terms and Abbreviations 2.0.0  UNISIG SUBSET-023 Glossary of Terms and Abbreviations 3.0.0 
4 UNISIG SUBSET-026 System Requirements Specification 2.3.0  UNISIG SUBSET-026 System Requirements Specification 3.3.0 
5 UNISIG SUBSET-027 FFFIS Juridical recorder-downloading tool 2.3.0 Note 1 UNISIG SUBSET-027 FIS Juridical Recording 3.0.0 
6 UNISIG SUBSET-033 FIS for man-machine interface 2.0.0  ERA_ERTMS_015560 ETCS Driver Machine interface 3.3.0 
7 UNISIG SUBSET-034 FIS for the train interface 2.0.0  UNISIG SUBSET-034 Train Interface FIS 3.0.0 
8 UNISIG SUBSET-035 Specific Transmission Module FFFIS 2.1.1  UNISIG SUBSET-035 Specific Transmission Module FFFIS 3.0.0 
9 UNISIG SUBSET-036 FFFIS for Eurobalise 2.4.1  UNISIG SUBSET-036 FFFIS for Eurobalise 3.0.0 
10 UNISIG SUBSET-037 EuroRadio FIS 2.3.0  UNISIG SUBSET-037 EuroRadio FIS 3.0.0 
11 UNISIG SUBSET-038 Offline key management FIS 2.3.0  UNISIG SUBSET-038 Offline key management FIS 3.0.0 
12 UNISIG SUBSET-039 FIS for the RBC/RBC handover 2.3.0  ReservedUNISIG SUBSET-039 FIS for the RBC/RBC handover  
13 UNISIG SUBSET-040 Dimensioning and Engineering rules 2.3.0  UNISIG SUBSET-040 Dimensioning and Engineering rules 3.2.0 
14 UNISIG SUBSET-041 Performance Requirements for Interoperability 2.1.0  UNISIG SUBSET-041 Performance Requirements for Interoperability 3.1.0 
15 ERA SUBSET-108 Interoperability related consolidation on TSI Annex A documents 1.2.0  Intentionally deleted   
16 UNISIG SUBSET-044 FFFIS for Euroloop 2.3.0  UNISIG SUBSET-044 FFFIS for Euroloop 2.4.0 
17 Intentionally deleted    Intentionally deleted   
18 UNISIG SUBSET-046 Radio infill FFFS 2.0.0  Intentionally deleted   
19 UNISIG SUBSET-047 Trackside-Trainborne FIS for Radio infill 2.0.0  UNISIG SUBSET-047 Trackside-Trainborne FIS for Radio infill 3.0.0 
20 UNISIG SUBSET-048 Trainborne FFFIS for Radio infill 2.0.0  UNISIG SUBSET-048 Trainborne FFFIS for Radio infill 3.0.0 
21 UNISIG SUBSET-049 Radio infill FIS with LEU/interlocking 2.0.0  Intentionally deleted   
22 Intentionally deleted    Intentionally deleted   
23 UNISIG SUBSET-054 Responsibilities and rules for the assignment of values to ETCS variables 2.1.0  UNISIG SUBSET-054 Responsibilities and rules for the assignment of values to ETCS variables 3.0.0 
24 Intentionally deleted    Intentionally deleted   
25 UNISIG SUBSET-056 STM FFFIS Safe time layer 2.2.0  UNISIG SUBSET-056 STM FFFIS Safe time layer 3.0.0 
26 UNISIG SUBSET-057 STM FFFIS Safe link layer 2.2.0  UNISIG SUBSET-057 STM FFFIS Safe link layer 3.0.0 
27 UNISIG SUBSET-091 Safety Requirements for the Technical Interoperability of ETCS in Levels 1 and 2 2.5.0  UNISIG SUBSET-091 Safety Requirements for the Technical Interoperability of ETCS in Levels 1 and 2 3.2.0 
28 Reserved Reliability — availability requirements   Reserved Reliability — availability requirements  
29 UNISIG SUBSET-102 Test specification for interface ‘K’ 1.0.0  UNISIG SUBSET-102 Test specification for interface ‘K’ 2.0.0 
30 Intentionally deleted    Intentionally deleted   
31 UNISIG SUBSET-094 Functional requirements for an on-board reference test facility 2.0.2  ReservedUNISIG SUBSET-094 Functional requirements for an on-board reference test facility  
32 EIRENE FRS GSM-R Functional requirements specification 7.3.0  EIRENE FRS GSM-R Functional requirements specification 7.3.0 
33 EIRENE SRS GSM-R System requirements specification 15.3.0  EIRENE SRS GSM-R System requirements specification 15.3.0 
34 A11T6001 (MORANE) Radio Transmission FFFIS for EuroRadio 12.4  A11T6001 (MORANE) Radio Transmission FFFIS for EuroRadio 12.4 
35 Intentionally deleted    Intentionally deleted   
36 a Intentionally deleted    Intentionally deleted   
36 b Intentionally deleted    Intentionally deleted   
36 c UNISIG SUBSET-074-2 FFFIS STM Test cases document 1.0.0  ReservedUNISIG SUBSET-074-2 FFFIS STM Test cases document  
37 a Intentionally deleted    Intentionally deleted   
37 b UNISIG SUBSET-076-5-2 Test cases related to features 2.3.3  ReservedUNISIG SUBSET-076-5-2 Test cases related to features  
37 c UNISIG SUBSET-076-6-3 Test sequences 2.3.3  ReservedUNISIG SUBSET-076-6-3 Test sequences  
37 d UNISIG SUBSET-076-7 Scope of the test specifications 1.0.2  ReservedUNISIG SUBSET-076-7 Scope of the test specifications  
37 e Intentionally deleted    Intentionally deleted   
38 06E068 ETCS Marker-board definition 2.0  06E068 ETCS Marker-board definition 2.0 
39 UNISIG SUBSET-092-1 ERTMS EuroRadio Conformance Requirements 2.3.0  UNISIG SUBSET-092-1 ERTMS EuroRadio Conformance Requirements 3.0.0 
40 UNISIG SUBSET-092-2 ERTMS EuroRadio test cases safety layer 2.3.0  UNISIG SUBSET-092-2 ERTMS EuroRadio test cases safety layer 3.0.0 
41 Intentionally deleted    Intentionally deleted   
42 Intentionally deleted    Intentionally deleted   
43 UNISIG SUBSET 085 Test specification for Eurobalise FFFIS 2.2.2  UNISIG SUBSET 085 Test specification for Eurobalise FFFIS 3.0.0 
44 Reserved Odometry FIS   Reserved Odometry FIS  
45 UNISIG SUBSET-101 Interface ‘K’ Specification 1.0.0  UNISIG SUBSET-101 Interface ‘K’ Specification 2.0.0 
46 UNISIG SUBSET-100 Interface ‘G’ Specification 1.0.1  UNISIG SUBSET-100 Interface ‘G’ Specification 2.0.0 
47 Intentionally deleted    Intentionally deleted   
48 Reserved Test specification for mobile equipment GSM-R   Reserved Test specification for mobile equipment GSM-R  
49 UNISIG SUBSET-059 Performance requirements for STM 2.1.1  UNISIG SUBSET-059 Performance requirements for STM 3.0.0. 
50 UNISIG SUBSET-103 Test specification for Euroloop 1.0.0  UNISIG SUBSET-103 Test specification for Euroloop 1.1.0 
51 Reserved Ergonomic aspects of the DMI   Intentionally deleted   
52 UNISIG SUBSET-058 FFFIS STM Application layer 2.1.1  UNISIG SUBSET-058 FFFIS STM Application layer 3.0.0 
53 Intentionally deleted    Intentionally deleted   
54 Intentionally deleted    Intentionally deleted   
55 Intentionally deleted    Intentionally deleted   
56 Intentionally deleted    Intentionally deleted   
57 Intentionally deleted    Intentionally deleted   
58 Intentionally deleted    Intentionally deleted   
59 Intentionally deleted    Intentionally deleted   
60 Intentionally deleted    UNISIG SUBSET-104 ETCS System Version Management 3.1.0 
61 Intentionally deleted    Intentionally deleted   
62 Reserved RBC-RBC Test specification for safe communication interface   Intentionally deleted   
63 UNISIG SUBSET-098 RBC-RBC Safe Communication Interface 1.0.0  UNISIG SUBSET-098 RBC-RBC Safe Communication Interface 3.0.0 
64 EN 301 515 Global System for Mobile Communication (GSM);Requirements for GSM operation on railways 2.3.0 Note 2 EN 301 515 Global System for Mobile Communication (GSM);Requirements for GSM operation on railways 2.3.0 Note 2
65 TS 102 281 Detailed requirements for GSM operation on railways 2.2.0 Note 3 TS 102 281 Detailed requirements for GSM operation on railways 2.2.0 Note 3
66 (MORANE) A 01 T 0004 1 ASCI Options for Interoperability 1  (MORANE) A 01 T 0004 1 ASCI Options for Interoperability 1 
67 (MORANE) P 38 T 9001 FFFIS for GSM-R SIM Cards 4.1  (MORANE) P 38 T 9001 FFFIS for GSM-R SIM Cards 4.1 
68 ETSI TS 102 610 Railway Telecommunication; GSM;Usage of the UUIE for GSM operation on railways 1.1.0  ETSI TS 102 610 Railway Telecommunication; GSM;Usage of the UUIE for GSM operation on railways 1.1.0 
69 (MORANE) F 10 T 6002 FFFS for Confirmation of High Priority Calls’ 4  (MORANE) F 10 T 6002 FFFS for Confirmation of High Priority Calls’ 4 
70 (MORANE) F 12 T 6002 FIS for Confirmation of High Priority Calls 4  (MORANE) F 12 T 6002 FIS for Confirmation of High Priority Calls 4 
71 (MORANE) E 10 T 6001 FFFS for Functional Addressing 4  (MORANE) E 10 T 6001 FFFS for Functional Addressing 4 
72 (MORANE) E 12 T 6001 FIS for Functional Addressing 5.1  (MORANE) E 12 T 6001 FIS for Functional Addressing 5.1 
73 (MORANE) F 10 T6001 FFFS for Location Dependent Addressing 4  (MORANE) F 10 T6001 FFFS for Location Dependent Addressing 4 
74 (MORANE) F 12 T6001 FIS for Location Dependent Addressing 3  (MORANE) F 12 T6001 FIS for Location Dependent Addressing 3 
75 (MORANE) F 10 T 6003 FFFS for Presentation of Functional Numbers to Called and Calling Parties 4  (MORANE) F 10 T 6003 FFFS for Presentation of Functional Numbers to Called and Calling Parties 4 
76 (MORANE) F 12 T 6003 FIS for Presentation of Functional Numbers to Called and Calling Parties 4  (MORANE) F 12 T 6003 FIS for Presentation of Functional Numbers to Called and Calling Parties 4 
77 ERA/ERTMS/033281 Interfaces between CCS track-side and other subsystems 1.0  ERA/ERTMS/033281 Interfaces between CCS track-side and other subsystems 1.0 
78 Reserved Safety requirements for ETCS DMI functions   Reserved Safety requirements for ETCS DMI functions  
79 Not applicable Not applicable   UNISIG SUBSET-114 KMC-ETCS Entity Off-line KM FIS 1.0.0 
80 Not applicable Not applicable   Reserved GSM-R Driver Machine Interface  
 Note 1: only the functional description of information to be recorded is mandatory, not the technical characteristics of the interface.
 Note 2: the specifications listed in section 2.1 of EN 301 515 are mandatory.
 Note 3: the change requests (CRs) listed in table 1 and 2 of TR 102 281 are mandatory.
 Table A 3 
The standards listed in this table shall be applied in the certification process, without prejudice to chapter 4 and chapter 6 of this TSI.


No Reference Document name and comments Version
A1 EN 50126 Railway applications — The specification and demonstration of reliability, availability, maintainability and safety (RAMS) 1999
A2 EN 50128 Railway applications — Communication, signalling and processing systems — Software for railway control and protection systems 2001
A3 EN 50129 Railway applications — Communication, signalling and processing systems — Safety related electronic systems for signalling 2003
A4 EN 50159-1 Railway applications — Communication, signalling and processing systems — Part 1: Safety related communication in closed transmission systems 2001
A5 EN 50159-2 Railway applications — Communication, signalling and processing systems — Part 2: Safety related communication in open transmission systems 2001


ANNEX II


ANNEX G 
Open Point Notes
Braking aspects It only applies to ERTMS/ETCS Baseline 2 (see Annex A, Table A2, Index 15).Resolved for ERTMS/ETCS Baseline 3 (see Annex A, Table A 2, Indexes 4 and 13).
Index 28 – Reliability/availability requirements Frequent occurrences of degraded situations caused by failures of control-command and signalling equipment will decrease the system safety.
Minimum wheel diameter for speed greater than 350 km/h See Annex A, Table A 2, Index 77
Minimum axle distance for speed greater than 350 km/h See Annex A, Table A 2, Index 77
Metal and inductive components free space between wheels See Annex A, Table A 2, Index 77This is not an open point for freight wagons
Characteristics of sand applied to tracks See Annex A, Table A 2, Index 77
Vehicle metal mass See Annex A, Table A 2, Index 77
Combination of rolling stock characteristics influencing shunting impedance See Annex A, Table A 2, Index 77
Electromagnetic interferences (traction current) See Annex A, Table A 2, Index 77
Electromagnetic interferences (electromagnetic fields) See Annex A, Table A 2, Index 77This is not an open point for power systems other than DC
Vehicle Impedance See Annex A, Table A 2, Index 77
DC and low frequency components of traction current See Annex A, Table A 2, Index 77
Use of magnetic/eddy current brakes See Annex A, Table A 2, Index 77
Index 78 — Safety requirements for ETCS DMI functions This open point is related to the interface between ETCS on-board and the driver, i.e. errors in displaying information and in entering data and commands.
