
Article 1 
The use of the following methods is hereby authorized for grading pig carcases pursuant to Regulation (EEC) No 3220/84 in Denmark:

((a)) the apparatus termed ‘Klassificeringscenter (KC)’ and assessment methods related thereto, details of which are given in Part 1 of the Annex;
((b)) the apparatus termed ‘Fat-O-Meater/Manuel Klassificering (FOM/MK)’ and assessment methods related thereto, details of which are given in Part 2 of the Annex;
((c)) the apparatus termed ‘Uni-Fat-O-Meater (Unifom)’ and assessment methods related thereto, details of which are given in Part 3 of the Annex;
((d)) the apparatus termed ‘Fully automatic ultrasonic equipment (AutoFOM 1)’ and assessment methods related thereto, details of which are given in Part 4 of the Annex;
((e)) the apparatus termed ‘Updated fully automatic ultrasonic equipment (AutoFOM DK)’ and assessment methods related thereto, details of which are given in Part 5 of the Annex;
((f)) the apparatus termed ‘Fat-O-Meater II (FOM II)’ and assessment methods related thereto, details of which are given in Part 6 of the Annex.
Article 2 
Modifications of the apparata or the assessment methods shall not be authorised.
Article 3 
Decision 92/469/EEC is hereby repealed.
Article 4 
This Decision is addressed to the Kingdom of Denmark.
Done at Brussels, 19 December 2008.
For the Commission
Mariann FISCHER BOEL
Member of the Commission
ANNEX
Part 1
1. Grading of pig carcases shall be carried out by means of the apparatus termed ‘Klassificeringscenter (KC)’.

2. The apparatus shall be equipped with nine probes of six millimetres each containing a photodiode (Siemens of the type SFH 950 LD242 II or similar) and a photodetector (Siemens of the type SFH 960 — PB 103 or similar) and having an operation distance of between one and 180 millimetres. The results of the measurements are converted into estimated lean meat content by means of a central unit.

3. 
 = 70,5489 – 0,1572 x1 – 0,1698 x2 – 0,1537 x3 – 0,1803 x4 – 0,2115 x5 – 0,1669 x6 – 0,1269 x7 + 0,04278 x8 + 0,0234 x9 + 0,0371 x10

where:

the estimated percentage of lean meat in carcase.

4. 
x1the thickness of backfat (including rind) in millimetres, measured at the centre of the third cervical vertebra, at 10,5 cm off the midline of the carcase.x2the thickness of backfat (including rind) in millimetres, measured at the centre of fourth cervical vertebra, at 7 cm off the midline of the carcase.x3the thickness of backfat (including rind) in millimetres, measured between fourth and fifth hindmost thoracic vertebra, at 3 cm off the midline of the carcase.x4the thickness of backfat (including rind) in millimetres, measured between second and third hindmost thoracic vertebra, at 7 cm off the midline of the carcase.x5the thickness of backfat (including rind) in millimetres, measured between first lumbar vertebra and last thoracic vertebra, at 6 cm off the midline of the carcase.x6the thickness of backfat (including rind) in millimetres, measured 4 cm before the fore edge of the pubic bone, at 7 cm off the midline of the carcase.x7the thickness of backfat (including rind) in millimetres, measured at the fore edge of the pubic bone, at 11 cm off the midline of the carcase.x8muscle thickness in millimetres, measured between fourth and fifth hindmost thoracic vertebra, at 3 cm off the midline of the carcase.x9muscle thickness in millimetres, measured between second and third hindmost thoracic vertebra, at 7 cm off the midline of the carcase.x10muscle thickness in millimetres, measured between first lumbar vertebra and hindmost thoracic vertebra, at 6 cm off the midline of the carcase.

The formulae shall be valid for carcases weighing between 50 and 110 kg.

Part 2
1. Pig carcase grading shall be carried out using the apparatus termed ‘Fat-O-Meater/Manuel Klassificering (FOM/MK)’.

2. The apparatus is a Fat-O-Meater type of equipment and it shall be equipped with a probe of six millimetres diameter containing a photodetector (Siemens of the type SFH 960 — BP 103 or similar) and having an operation distance of between one and 94 millimetres.

3. 
The lean meat content of the carcase shall be calculated according to the following formula

 = 68,1746 – 0,3220 x1 – 0,5326 x2 + 0,0836 x3

where:

the estimated percentage of lean meat in carcase.

4. 
x1the thickness of backfat (including rind) in millimetres, measured at 8 cm off the midline of the carcase between the third and fourth last lumbar vertebrae.x2the thickness of backfat (including rind) in millimetres, measured at 6 cm off the midline of the carcase between the third and fourth last ribs.x3the thickness of muscle in millimetres, measured at the same time and in the same place as x2.

The formulae shall be valid for carcases weighing between 50 and 110 kg.

Part 3
1. Grading of pig carcases shall be carried out by means of the apparatus termed ‘Uni-Fat-O-Meater’ (Unifom).

2. The apparatus is the same as the apparatus described under point 2 of part 2. However, Unifom differs from MK with regard to computer and software for the interpretation of the reflection profile from the optical probe.

3. 
 = 66,7393 – 0,2655 x1 – 0,5432 x2 + 0,0838 x3

where:

the estimated percentage of lean meat in carcase.

4. 
x1the thickness of backfat (including rind) in millimetres, measured at 8 cm off the midline of the carcase between the third and fourth last lumbar vertebrae.x2the thickness of backfat (including rind) in millimetres, measured at 6 cm off the midline of the carcase between the third and fourth last ribs.x3the thickness of muscle in millimetres, measured at the same time and in the same place as x2.

The formulae shall be valid for carcases weighing between 50 and 110 kg.

Part 4
1. Grading of the pig carcases shall be carried out by means of the apparatus termed ‘Fully automatic ultrasonic equipment (AutoFOM 1)’.

2. 
The results of the measurements are converted into estimated lean mean content by means of a central data-processing unit.

3. 
 = c + c0 × IP000 + c1 × IP001 + .... + c126 × IP126

where:

the estimated percentage of lean meat in carcase. The constants c and c0 up to c126 appear from the Danish Protocol, Part II, submitted to the Commission under the terms of Article 3(3) of Commission Regulation (EEC) No 2967/85.

4. 
The formula shall be valid for carcases weighing between 50 and 110 kg.

Part 5
1. Grading of pig carcase shall be carried out by means of the apparatus termed ‘Updated fully automatic ultrasonic equipment (AutoFOM DK)’.

2. The apparatus is mechanically compatible with the AutoFOM 1 concerning the scanner array itself. Likewise, the measuring principle itself remains unchanged. AutoFOM DK differs from AutoFOM 1 with regard to a fixture which ensures that the carcase passes the measuring unit in a straight position, and which together with a laser sensor detecting the carcase, provides symmetric measurements, with more computation power and a new software packages providing the opportunity to enhance the imaging speed and resolution.

3. 
 = 63,4322 – 0,1429 x1 – 0,0438 x2 – 0,0715 x3 + 0,9420 x4 + 0,0911 x5

where:

the estimated percentage of lean meat in carcase.

4. 
The formula shall be valid for carcases weighing between 50 and 110 kg.

Part 6
1. Grading of pig carcase shall be carried out by means of the apparatus termed ‘Fat-O-Meater II (FOM II)’.

2. The apparatus is a new version of the FAT-O-Meater measurement system. The basic measurement principle, as described in point 2 in Part 2 and 3, is unchanged, but all software, hardware as well as the mechanical design is redesigned. The FOM II pistol consists of an optical probe with a knife, a depth measurement device and a data acquisition and analysis board. All legally relevant acquisition and analysis are contained within the FOM II pistol.

3. 
 = 66,5015 – 0,3568 x1 – 0,4704 x2 + 0,0947 x3

where:

the estimated percentage of lean meat in carcase.

4. 
x1the thickness of backfat (including rind) in millimetres, measured at 8 cm off the midline of the carcase between the third and fourth last lumbar vertebrae.x2the thickness of backfat (including rind) in millimetres, measured at 6 cm off the midline of the carcase between the third and fourth last ribs.x3the thickness of muscle in millimetres, measured at the same time and in the same place as x2.

The formula shall be valid for carcases weighing between 50 and 110 kg.
