
Article 1 
The goods described in column 1 of the annexed table are now classified within the combined nomenclature under the appropriate CN codes indicated in column 2 of the said table.
Article 2 
Binding tariff information isued by the customs authorities of Member States which do not conform to the rights established by this Regulation can continue to be invoked under the provisions of Article 12 (6) of Regulation (EEC) No 2913/92 for a period of three months.
Article 3 
This Regulation shall enter into force on the 21st day following its publication in the Official Journal of the European Communities.
This Regulation shall be binding in its entirety and directly applicable in all Member States.Done at Brussels, 23 May 1995.
For the Commission
Mario MONTI
Member of the Commission
ANNEX

Description of goods Classification CN code Reason
(1) (2) (3)

1. An ornamental article (luminous fountain or ‘running tap’), put up unassembled in a packing for retail sale. Assembled, the various plastic components (a base about 15 cm diameter, incorporating a lighting system and an electric motor with a power-supply cable, and equipped with a switch, three basins, various pipe connections, a tap, a small figure of a dancer, artificial flowers and foliage, etc.) form one or other of the articles depicted (height between 30 cm and 40 cm)
 3926 40 00 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature and by the wording of CN codes 3926 and 3926 40 00

2. Slippers consisting of a textile upper and an outer sole of plastic (approximately one centimetre thick), the outside of which is entirely covered by a very thin layer of textile material, with poor wearing properties, stuck along the edges
 6404 19 10 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature, note 4 (b) to Chapter 64 and by the wording of CN codes 6404, 6404 19 and 6404 19 10

3. 

((a)) one or more library storage modules (each containing cartridge storage cells and a microprocessor controlled robot and having one or more attached cartridge drive frames and control units); and
((b)) a library management unit with integral software (which acts as the link between the library storage modules and one or more central processing units).

This system is specifically designed for the automatic loading, processing, storage and unloading of magnetic tape cartridges for automatic data processing purposes
 8471 99 10 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature, by note 5 B to Chapter 84 and by the wording of CN codes 8471, 8471 99 and 8471 99 10

4. 
With such a card, an ADP-machine can be used as an input-output device for another machine or a central processing unit.

The card constitutes a printed circuit of a size of about 10 x 21 cm incorporating integrated circuits and active and passive components.

It is fitted with a row of pin contacts corresponding to an expansion slot in the ADP-machine, with an attachment to the connection cable of the LAN and light emitting diodes (LEDs)
 8517 82 90 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature, by note 5 to Chapter 84 and by the wording of CN codes 8517, 8517 82 and 8517 82 90

5. 
The receiver comprises a magnet, a coil and a diaphragm to recieve electrical signals which cause the diaphragm to vibrate thus producing audible sound.

The receiver may be used together with an amplifier as a hearing aid
 8518 30 90 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature, by note 2 (a) to Chapter 90 and by the wording of CN codes 8518, 8518 30 and 8518 30 90

6. 
The scanning device uses an optical system, consisting of a lamp, mirrors, lenses and photocells to scan the original image line by line.

The copies are produced electrostatically via a drum on the laser printer using the indirect process. The laser copier has several additional features for altering the original image, e.g. reduction, enlargement, shading
 9009 12 00 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature and by the wording of CN codes 9009 and 9009 12 00

7. Little star and heart shapes in a variety of colours (red, green and shiny silver) and multicoloured granules, the size of pinheads, made from plastic film, and used to decorate e.g. a table on which food for a carnival celebration, children's party or Advent festivity is served. The decorative effect is achieved by sprinkling the products
 9505 90 00 Classification is determined by the provisions of General Rules 1 and 6 for the interpretation of the combined nomenclature and by the wording of CN codes 9505 and 9505 90 00

